1 /*
2 * Copyright (C) 2000 Deep Blue Solutions Ltd
3 * Copyright (C) 2002 Shane Nay (shane@minirl.com)
4 * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
10 *
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
15 */
16
17 #include <linux/types.h>
18 #include <linux/init.h>
19 #include <linux/clk.h>
20 #include <linux/serial_8250.h>
21 #include <linux/gpio.h>
22 #include <linux/i2c.h>
23 #include <linux/irq.h>
24 #include <linux/irqdomain.h>
25
26 #include <asm/mach-types.h>
27 #include <asm/mach/arch.h>
28 #include <asm/mach/time.h>
29 #include <asm/memory.h>
30 #include <asm/mach/map.h>
31
32 #ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
33 #include <linux/mfd/wm8350/audio.h>
34 #include <linux/mfd/wm8350/core.h>
35 #include <linux/mfd/wm8350/pmic.h>
36 #endif
37
38 #include "common.h"
39 #include "devices-imx31.h"
40 #include "hardware.h"
41 #include "iomux-mx3.h"
42
43 /* Base address of PBC controller */
44 #define PBC_BASE_ADDRESS MX31_CS4_BASE_ADDR_VIRT
45
46 /* PBC Board interrupt status register */
47 #define PBC_INTSTATUS 0x000016
48
49 /* PBC Board interrupt current status register */
50 #define PBC_INTCURR_STATUS 0x000018
51
52 /* PBC Interrupt mask register set address */
53 #define PBC_INTMASK_SET 0x00001A
54
55 /* PBC Interrupt mask register clear address */
56 #define PBC_INTMASK_CLEAR 0x00001C
57
58 /* External UART A */
59 #define PBC_SC16C652_UARTA 0x010000
60
61 /* External UART B */
62 #define PBC_SC16C652_UARTB 0x010010
63
64 #define PBC_INTSTATUS_REG (PBC_INTSTATUS + PBC_BASE_ADDRESS)
65 #define PBC_INTMASK_SET_REG (PBC_INTMASK_SET + PBC_BASE_ADDRESS)
66 #define PBC_INTMASK_CLEAR_REG (PBC_INTMASK_CLEAR + PBC_BASE_ADDRESS)
67
68 #define EXPIO_INT_XUART_INTA 10
69 #define EXPIO_INT_XUART_INTB 11
70
71 #define MXC_MAX_EXP_IO_LINES 16
72
73 /* CS8900 */
74 #define EXPIO_INT_ENET_INT 8
75 #define CS4_CS8900_MMIO_START 0x20000
76
77 static struct irq_domain *domain;
78
79 /*
80 * The serial port definition structure.
81 */
82 static struct plat_serial8250_port serial_platform_data[] = {
83 {
84 .membase = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTA),
85 .mapbase = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTA),
86 .uartclk = 14745600,
87 .regshift = 0,
88 .iotype = UPIO_MEM,
89 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
90 }, {
91 .membase = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTB),
92 .mapbase = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTB),
93 .uartclk = 14745600,
94 .regshift = 0,
95 .iotype = UPIO_MEM,
96 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
97 },
98 {},
99 };
100
101 static struct platform_device serial_device = {
102 .name = "serial8250",
103 .id = 0,
104 .dev = {
105 .platform_data = serial_platform_data,
106 },
107 };
108
109 static struct resource mx31ads_cs8900_resources[] __initdata = {
110 DEFINE_RES_MEM(MX31_CS4_BASE_ADDR + CS4_CS8900_MMIO_START, SZ_64K),
111 DEFINE_RES_IRQ(-1),
112 };
113
114 static const struct platform_device_info mx31ads_cs8900_devinfo __initconst = {
115 .name = "cs89x0",
116 .id = 0,
117 .res = mx31ads_cs8900_resources,
118 .num_res = ARRAY_SIZE(mx31ads_cs8900_resources),
119 };
120
mxc_init_extuart(void)121 static int __init mxc_init_extuart(void)
122 {
123 serial_platform_data[0].irq = irq_find_mapping(domain,
124 EXPIO_INT_XUART_INTA);
125 serial_platform_data[1].irq = irq_find_mapping(domain,
126 EXPIO_INT_XUART_INTB);
127 return platform_device_register(&serial_device);
128 }
129
mxc_init_ext_ethernet(void)130 static void __init mxc_init_ext_ethernet(void)
131 {
132 mx31ads_cs8900_resources[1].start =
133 irq_find_mapping(domain, EXPIO_INT_ENET_INT);
134 mx31ads_cs8900_resources[1].end =
135 irq_find_mapping(domain, EXPIO_INT_ENET_INT);
136 platform_device_register_full(
137 (struct platform_device_info *)&mx31ads_cs8900_devinfo);
138 }
139
140 static const struct imxuart_platform_data uart_pdata __initconst = {
141 .flags = IMXUART_HAVE_RTSCTS,
142 };
143
144 static unsigned int uart_pins[] = {
145 MX31_PIN_CTS1__CTS1,
146 MX31_PIN_RTS1__RTS1,
147 MX31_PIN_TXD1__TXD1,
148 MX31_PIN_RXD1__RXD1
149 };
150
mxc_init_imx_uart(void)151 static inline void mxc_init_imx_uart(void)
152 {
153 mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins), "uart-0");
154 imx31_add_imx_uart0(&uart_pdata);
155 }
156
mx31ads_expio_irq_handler(u32 irq,struct irq_desc * desc)157 static void mx31ads_expio_irq_handler(u32 irq, struct irq_desc *desc)
158 {
159 u32 imr_val;
160 u32 int_valid;
161 u32 expio_irq;
162
163 imr_val = __raw_readw(PBC_INTMASK_SET_REG);
164 int_valid = __raw_readw(PBC_INTSTATUS_REG) & imr_val;
165
166 expio_irq = 0;
167 for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
168 if ((int_valid & 1) == 0)
169 continue;
170
171 generic_handle_irq(irq_find_mapping(domain, expio_irq));
172 }
173 }
174
175 /*
176 * Disable an expio pin's interrupt by setting the bit in the imr.
177 * @param d an expio virtual irq description
178 */
expio_mask_irq(struct irq_data * d)179 static void expio_mask_irq(struct irq_data *d)
180 {
181 u32 expio = d->hwirq;
182 /* mask the interrupt */
183 __raw_writew(1 << expio, PBC_INTMASK_CLEAR_REG);
184 __raw_readw(PBC_INTMASK_CLEAR_REG);
185 }
186
187 /*
188 * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
189 * @param d an expio virtual irq description
190 */
expio_ack_irq(struct irq_data * d)191 static void expio_ack_irq(struct irq_data *d)
192 {
193 u32 expio = d->hwirq;
194 /* clear the interrupt status */
195 __raw_writew(1 << expio, PBC_INTSTATUS_REG);
196 }
197
198 /*
199 * Enable a expio pin's interrupt by clearing the bit in the imr.
200 * @param d an expio virtual irq description
201 */
expio_unmask_irq(struct irq_data * d)202 static void expio_unmask_irq(struct irq_data *d)
203 {
204 u32 expio = d->hwirq;
205 /* unmask the interrupt */
206 __raw_writew(1 << expio, PBC_INTMASK_SET_REG);
207 }
208
209 static struct irq_chip expio_irq_chip = {
210 .name = "EXPIO(CPLD)",
211 .irq_ack = expio_ack_irq,
212 .irq_mask = expio_mask_irq,
213 .irq_unmask = expio_unmask_irq,
214 };
215
mx31ads_init_expio(void)216 static void __init mx31ads_init_expio(void)
217 {
218 int irq_base;
219 int i, irq;
220
221 printk(KERN_INFO "MX31ADS EXPIO(CPLD) hardware\n");
222
223 /*
224 * Configure INT line as GPIO input
225 */
226 mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio");
227
228 /* disable the interrupt and clear the status */
229 __raw_writew(0xFFFF, PBC_INTMASK_CLEAR_REG);
230 __raw_writew(0xFFFF, PBC_INTSTATUS_REG);
231
232 irq_base = irq_alloc_descs(-1, 0, MXC_MAX_EXP_IO_LINES, numa_node_id());
233 WARN_ON(irq_base < 0);
234
235 domain = irq_domain_add_legacy(NULL, MXC_MAX_EXP_IO_LINES, irq_base, 0,
236 &irq_domain_simple_ops, NULL);
237 WARN_ON(!domain);
238
239 for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
240 irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
241 set_irq_flags(i, IRQF_VALID);
242 }
243 irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_4));
244 irq_set_irq_type(irq, IRQ_TYPE_LEVEL_HIGH);
245 irq_set_chained_handler(irq, mx31ads_expio_irq_handler);
246 }
247
248 #ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
249 /* This section defines setup for the Wolfson Microelectronics
250 * 1133-EV1 PMU/audio board. When other PMU boards are supported the
251 * regulator definitions may be shared with them, but for now they can
252 * only be used with this board so would generate warnings about
253 * unused statics and some of the configuration is specific to this
254 * module.
255 */
256
257 /* CPU */
258 static struct regulator_consumer_supply sw1a_consumers[] = {
259 {
260 .supply = "cpu_vcc",
261 }
262 };
263
264 static struct regulator_init_data sw1a_data = {
265 .constraints = {
266 .name = "SW1A",
267 .min_uV = 1275000,
268 .max_uV = 1600000,
269 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
270 REGULATOR_CHANGE_MODE,
271 .valid_modes_mask = REGULATOR_MODE_NORMAL |
272 REGULATOR_MODE_FAST,
273 .state_mem = {
274 .uV = 1400000,
275 .mode = REGULATOR_MODE_NORMAL,
276 .enabled = 1,
277 },
278 .initial_state = PM_SUSPEND_MEM,
279 .always_on = 1,
280 .boot_on = 1,
281 },
282 .num_consumer_supplies = ARRAY_SIZE(sw1a_consumers),
283 .consumer_supplies = sw1a_consumers,
284 };
285
286 /* System IO - High */
287 static struct regulator_init_data viohi_data = {
288 .constraints = {
289 .name = "VIOHO",
290 .min_uV = 2800000,
291 .max_uV = 2800000,
292 .state_mem = {
293 .uV = 2800000,
294 .mode = REGULATOR_MODE_NORMAL,
295 .enabled = 1,
296 },
297 .initial_state = PM_SUSPEND_MEM,
298 .always_on = 1,
299 .boot_on = 1,
300 },
301 };
302
303 /* System IO - Low */
304 static struct regulator_init_data violo_data = {
305 .constraints = {
306 .name = "VIOLO",
307 .min_uV = 1800000,
308 .max_uV = 1800000,
309 .state_mem = {
310 .uV = 1800000,
311 .mode = REGULATOR_MODE_NORMAL,
312 .enabled = 1,
313 },
314 .initial_state = PM_SUSPEND_MEM,
315 .always_on = 1,
316 .boot_on = 1,
317 },
318 };
319
320 /* DDR RAM */
321 static struct regulator_init_data sw2a_data = {
322 .constraints = {
323 .name = "SW2A",
324 .min_uV = 1800000,
325 .max_uV = 1800000,
326 .valid_modes_mask = REGULATOR_MODE_NORMAL,
327 .state_mem = {
328 .uV = 1800000,
329 .mode = REGULATOR_MODE_NORMAL,
330 .enabled = 1,
331 },
332 .state_disk = {
333 .mode = REGULATOR_MODE_NORMAL,
334 .enabled = 0,
335 },
336 .always_on = 1,
337 .boot_on = 1,
338 .initial_state = PM_SUSPEND_MEM,
339 },
340 };
341
342 static struct regulator_init_data ldo1_data = {
343 .constraints = {
344 .name = "VCAM/VMMC1/VMMC2",
345 .min_uV = 2800000,
346 .max_uV = 2800000,
347 .valid_modes_mask = REGULATOR_MODE_NORMAL,
348 .valid_ops_mask = REGULATOR_CHANGE_STATUS,
349 .apply_uV = 1,
350 },
351 };
352
353 static struct regulator_consumer_supply ldo2_consumers[] = {
354 { .supply = "AVDD", .dev_name = "1-001a" },
355 { .supply = "HPVDD", .dev_name = "1-001a" },
356 };
357
358 /* CODEC and SIM */
359 static struct regulator_init_data ldo2_data = {
360 .constraints = {
361 .name = "VESIM/VSIM/AVDD",
362 .min_uV = 3300000,
363 .max_uV = 3300000,
364 .valid_modes_mask = REGULATOR_MODE_NORMAL,
365 .valid_ops_mask = REGULATOR_CHANGE_STATUS,
366 .apply_uV = 1,
367 },
368 .num_consumer_supplies = ARRAY_SIZE(ldo2_consumers),
369 .consumer_supplies = ldo2_consumers,
370 };
371
372 /* General */
373 static struct regulator_init_data vdig_data = {
374 .constraints = {
375 .name = "VDIG",
376 .min_uV = 1500000,
377 .max_uV = 1500000,
378 .valid_modes_mask = REGULATOR_MODE_NORMAL,
379 .apply_uV = 1,
380 .always_on = 1,
381 .boot_on = 1,
382 },
383 };
384
385 /* Tranceivers */
386 static struct regulator_init_data ldo4_data = {
387 .constraints = {
388 .name = "VRF1/CVDD_2.775",
389 .min_uV = 2500000,
390 .max_uV = 2500000,
391 .valid_modes_mask = REGULATOR_MODE_NORMAL,
392 .apply_uV = 1,
393 .always_on = 1,
394 .boot_on = 1,
395 },
396 };
397
398 static struct wm8350_led_platform_data wm8350_led_data = {
399 .name = "wm8350:white",
400 .default_trigger = "heartbeat",
401 .max_uA = 27899,
402 };
403
404 static struct wm8350_audio_platform_data imx32ads_wm8350_setup = {
405 .vmid_discharge_msecs = 1000,
406 .drain_msecs = 30,
407 .cap_discharge_msecs = 700,
408 .vmid_charge_msecs = 700,
409 .vmid_s_curve = WM8350_S_CURVE_SLOW,
410 .dis_out4 = WM8350_DISCHARGE_SLOW,
411 .dis_out3 = WM8350_DISCHARGE_SLOW,
412 .dis_out2 = WM8350_DISCHARGE_SLOW,
413 .dis_out1 = WM8350_DISCHARGE_SLOW,
414 .vroi_out4 = WM8350_TIE_OFF_500R,
415 .vroi_out3 = WM8350_TIE_OFF_500R,
416 .vroi_out2 = WM8350_TIE_OFF_500R,
417 .vroi_out1 = WM8350_TIE_OFF_500R,
418 .vroi_enable = 0,
419 .codec_current_on = WM8350_CODEC_ISEL_1_0,
420 .codec_current_standby = WM8350_CODEC_ISEL_0_5,
421 .codec_current_charge = WM8350_CODEC_ISEL_1_5,
422 };
423
mx31_wm8350_init(struct wm8350 * wm8350)424 static int mx31_wm8350_init(struct wm8350 *wm8350)
425 {
426 wm8350_gpio_config(wm8350, 0, WM8350_GPIO_DIR_IN,
427 WM8350_GPIO0_PWR_ON_IN, WM8350_GPIO_ACTIVE_LOW,
428 WM8350_GPIO_PULL_UP, WM8350_GPIO_INVERT_OFF,
429 WM8350_GPIO_DEBOUNCE_ON);
430
431 wm8350_gpio_config(wm8350, 3, WM8350_GPIO_DIR_IN,
432 WM8350_GPIO3_PWR_OFF_IN, WM8350_GPIO_ACTIVE_HIGH,
433 WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
434 WM8350_GPIO_DEBOUNCE_ON);
435
436 wm8350_gpio_config(wm8350, 4, WM8350_GPIO_DIR_IN,
437 WM8350_GPIO4_MR_IN, WM8350_GPIO_ACTIVE_HIGH,
438 WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
439 WM8350_GPIO_DEBOUNCE_OFF);
440
441 wm8350_gpio_config(wm8350, 7, WM8350_GPIO_DIR_IN,
442 WM8350_GPIO7_HIBERNATE_IN, WM8350_GPIO_ACTIVE_HIGH,
443 WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
444 WM8350_GPIO_DEBOUNCE_OFF);
445
446 wm8350_gpio_config(wm8350, 6, WM8350_GPIO_DIR_OUT,
447 WM8350_GPIO6_SDOUT_OUT, WM8350_GPIO_ACTIVE_HIGH,
448 WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
449 WM8350_GPIO_DEBOUNCE_OFF);
450
451 wm8350_gpio_config(wm8350, 8, WM8350_GPIO_DIR_OUT,
452 WM8350_GPIO8_VCC_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
453 WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
454 WM8350_GPIO_DEBOUNCE_OFF);
455
456 wm8350_gpio_config(wm8350, 9, WM8350_GPIO_DIR_OUT,
457 WM8350_GPIO9_BATT_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
458 WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
459 WM8350_GPIO_DEBOUNCE_OFF);
460
461 wm8350_register_regulator(wm8350, WM8350_DCDC_1, &sw1a_data);
462 wm8350_register_regulator(wm8350, WM8350_DCDC_3, &viohi_data);
463 wm8350_register_regulator(wm8350, WM8350_DCDC_4, &violo_data);
464 wm8350_register_regulator(wm8350, WM8350_DCDC_6, &sw2a_data);
465 wm8350_register_regulator(wm8350, WM8350_LDO_1, &ldo1_data);
466 wm8350_register_regulator(wm8350, WM8350_LDO_2, &ldo2_data);
467 wm8350_register_regulator(wm8350, WM8350_LDO_3, &vdig_data);
468 wm8350_register_regulator(wm8350, WM8350_LDO_4, &ldo4_data);
469
470 /* LEDs */
471 wm8350_dcdc_set_slot(wm8350, WM8350_DCDC_5, 1, 1,
472 WM8350_DC5_ERRACT_SHUTDOWN_CONV);
473 wm8350_isink_set_flash(wm8350, WM8350_ISINK_A,
474 WM8350_ISINK_FLASH_DISABLE,
475 WM8350_ISINK_FLASH_TRIG_BIT,
476 WM8350_ISINK_FLASH_DUR_32MS,
477 WM8350_ISINK_FLASH_ON_INSTANT,
478 WM8350_ISINK_FLASH_OFF_INSTANT,
479 WM8350_ISINK_FLASH_MODE_EN);
480 wm8350_dcdc25_set_mode(wm8350, WM8350_DCDC_5,
481 WM8350_ISINK_MODE_BOOST,
482 WM8350_ISINK_ILIM_NORMAL,
483 WM8350_DC5_RMP_20V,
484 WM8350_DC5_FBSRC_ISINKA);
485 wm8350_register_led(wm8350, 0, WM8350_DCDC_5, WM8350_ISINK_A,
486 &wm8350_led_data);
487
488 wm8350->codec.platform_data = &imx32ads_wm8350_setup;
489
490 regulator_has_full_constraints();
491
492 return 0;
493 }
494
495 static struct wm8350_platform_data __initdata mx31_wm8350_pdata = {
496 .init = mx31_wm8350_init,
497 };
498 #endif
499
500 static struct i2c_board_info __initdata mx31ads_i2c1_devices[] = {
501 #ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
502 {
503 I2C_BOARD_INFO("wm8350", 0x1a),
504 .platform_data = &mx31_wm8350_pdata,
505 /* irq number is run-time assigned */
506 },
507 #endif
508 };
509
mxc_init_i2c(void)510 static void __init mxc_init_i2c(void)
511 {
512 #ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
513 mx31ads_i2c1_devices[0].irq =
514 gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
515 #endif
516 i2c_register_board_info(1, mx31ads_i2c1_devices,
517 ARRAY_SIZE(mx31ads_i2c1_devices));
518
519 mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1));
520 mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1));
521
522 imx31_add_imx_i2c1(NULL);
523 }
524
525 static unsigned int ssi_pins[] = {
526 MX31_PIN_SFS5__SFS5,
527 MX31_PIN_SCK5__SCK5,
528 MX31_PIN_SRXD5__SRXD5,
529 MX31_PIN_STXD5__STXD5,
530 };
531
mxc_init_audio(void)532 static void __init mxc_init_audio(void)
533 {
534 imx31_add_imx_ssi(0, NULL);
535 mxc_iomux_setup_multiple_pins(ssi_pins, ARRAY_SIZE(ssi_pins), "ssi");
536 }
537
538 /*
539 * Static mappings, starting from the CS4 start address up to the start address
540 * of the CS8900.
541 */
542 static struct map_desc mx31ads_io_desc[] __initdata = {
543 {
544 .virtual = (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
545 .pfn = __phys_to_pfn(MX31_CS4_BASE_ADDR),
546 .length = CS4_CS8900_MMIO_START,
547 .type = MT_DEVICE
548 },
549 };
550
mx31ads_map_io(void)551 static void __init mx31ads_map_io(void)
552 {
553 mx31_map_io();
554 iotable_init(mx31ads_io_desc, ARRAY_SIZE(mx31ads_io_desc));
555 }
556
mx31ads_init_irq(void)557 static void __init mx31ads_init_irq(void)
558 {
559 mx31_init_irq();
560 mx31ads_init_expio();
561 }
562
mx31ads_init(void)563 static void __init mx31ads_init(void)
564 {
565 imx31_soc_init();
566
567 mxc_init_extuart();
568 mxc_init_imx_uart();
569 mxc_init_i2c();
570 mxc_init_audio();
571 mxc_init_ext_ethernet();
572 }
573
mx31ads_timer_init(void)574 static void __init mx31ads_timer_init(void)
575 {
576 mx31_clocks_init(26000000);
577 }
578
579 MACHINE_START(MX31ADS, "Freescale MX31ADS")
580 /* Maintainer: Freescale Semiconductor, Inc. */
581 .atag_offset = 0x100,
582 .map_io = mx31ads_map_io,
583 .init_early = imx31_init_early,
584 .init_irq = mx31ads_init_irq,
585 .handle_irq = imx31_handle_irq,
586 .init_time = mx31ads_timer_init,
587 .init_machine = mx31ads_init,
588 .restart = mxc_restart,
589 MACHINE_END
590