1 /*
2 * linux/include/linux/mtd/nand.h
3 *
4 * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org>
5 * Steven J. Hill <sjhill@realitydiluted.com>
6 * Thomas Gleixner <tglx@linutronix.de>
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License version 2 as
10 * published by the Free Software Foundation.
11 *
12 * Info:
13 * Contains standard defines and IDs for NAND flash devices
14 *
15 * Changelog:
16 * See git changelog.
17 */
18 #ifndef __LINUX_MTD_NAND_H
19 #define __LINUX_MTD_NAND_H
20
21 #include <linux/wait.h>
22 #include <linux/spinlock.h>
23 #include <linux/mtd/mtd.h>
24 #include <linux/mtd/flashchip.h>
25 #include <linux/mtd/bbm.h>
26
27 struct mtd_info;
28 struct nand_flash_dev;
29 /* Scan and identify a NAND device */
30 extern int nand_scan(struct mtd_info *mtd, int max_chips);
31 /*
32 * Separate phases of nand_scan(), allowing board driver to intervene
33 * and override command or ECC setup according to flash type.
34 */
35 extern int nand_scan_ident(struct mtd_info *mtd, int max_chips,
36 struct nand_flash_dev *table);
37 extern int nand_scan_tail(struct mtd_info *mtd);
38
39 /* Free resources held by the NAND device */
40 extern void nand_release(struct mtd_info *mtd);
41
42 /* Internal helper for board drivers which need to override command function */
43 extern void nand_wait_ready(struct mtd_info *mtd);
44
45 /* locks all blocks present in the device */
46 extern int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
47
48 /* unlocks specified locked blocks */
49 extern int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
50
51 /* The maximum number of NAND chips in an array */
52 #define NAND_MAX_CHIPS 8
53
54 /*
55 * Constants for hardware specific CLE/ALE/NCE function
56 *
57 * These are bits which can be or'ed to set/clear multiple
58 * bits in one go.
59 */
60 /* Select the chip by setting nCE to low */
61 #define NAND_NCE 0x01
62 /* Select the command latch by setting CLE to high */
63 #define NAND_CLE 0x02
64 /* Select the address latch by setting ALE to high */
65 #define NAND_ALE 0x04
66
67 #define NAND_CTRL_CLE (NAND_NCE | NAND_CLE)
68 #define NAND_CTRL_ALE (NAND_NCE | NAND_ALE)
69 #define NAND_CTRL_CHANGE 0x80
70
71 /*
72 * Standard NAND flash commands
73 */
74 #define NAND_CMD_READ0 0
75 #define NAND_CMD_READ1 1
76 #define NAND_CMD_RNDOUT 5
77 #define NAND_CMD_PAGEPROG 0x10
78 #define NAND_CMD_READOOB 0x50
79 #define NAND_CMD_ERASE1 0x60
80 #define NAND_CMD_STATUS 0x70
81 #define NAND_CMD_SEQIN 0x80
82 #define NAND_CMD_RNDIN 0x85
83 #define NAND_CMD_READID 0x90
84 #define NAND_CMD_ERASE2 0xd0
85 #define NAND_CMD_PARAM 0xec
86 #define NAND_CMD_GET_FEATURES 0xee
87 #define NAND_CMD_SET_FEATURES 0xef
88 #define NAND_CMD_RESET 0xff
89
90 #define NAND_CMD_LOCK 0x2a
91 #define NAND_CMD_UNLOCK1 0x23
92 #define NAND_CMD_UNLOCK2 0x24
93
94 /* Extended commands for large page devices */
95 #define NAND_CMD_READSTART 0x30
96 #define NAND_CMD_RNDOUTSTART 0xE0
97 #define NAND_CMD_CACHEDPROG 0x15
98
99 #define NAND_CMD_NONE -1
100
101 /* Status bits */
102 #define NAND_STATUS_FAIL 0x01
103 #define NAND_STATUS_FAIL_N1 0x02
104 #define NAND_STATUS_TRUE_READY 0x20
105 #define NAND_STATUS_READY 0x40
106 #define NAND_STATUS_WP 0x80
107
108 /*
109 * Constants for ECC_MODES
110 */
111 typedef enum {
112 NAND_ECC_NONE,
113 NAND_ECC_SOFT,
114 NAND_ECC_HW,
115 NAND_ECC_HW_SYNDROME,
116 NAND_ECC_HW_OOB_FIRST,
117 NAND_ECC_SOFT_BCH,
118 } nand_ecc_modes_t;
119
120 /*
121 * Constants for Hardware ECC
122 */
123 /* Reset Hardware ECC for read */
124 #define NAND_ECC_READ 0
125 /* Reset Hardware ECC for write */
126 #define NAND_ECC_WRITE 1
127 /* Enable Hardware ECC before syndrome is read back from flash */
128 #define NAND_ECC_READSYN 2
129
130 /* Bit mask for flags passed to do_nand_read_ecc */
131 #define NAND_GET_DEVICE 0x80
132
133
134 /*
135 * Option constants for bizarre disfunctionality and real
136 * features.
137 */
138 /* Buswidth is 16 bit */
139 #define NAND_BUSWIDTH_16 0x00000002
140 /* Chip has cache program function */
141 #define NAND_CACHEPRG 0x00000008
142 /*
143 * Chip requires ready check on read (for auto-incremented sequential read).
144 * True only for small page devices; large page devices do not support
145 * autoincrement.
146 */
147 #define NAND_NEED_READRDY 0x00000100
148
149 /* Chip does not allow subpage writes */
150 #define NAND_NO_SUBPAGE_WRITE 0x00000200
151
152 /* Device is one of 'new' xD cards that expose fake nand command set */
153 #define NAND_BROKEN_XD 0x00000400
154
155 /* Device behaves just like nand, but is readonly */
156 #define NAND_ROM 0x00000800
157
158 /* Device supports subpage reads */
159 #define NAND_SUBPAGE_READ 0x00001000
160
161 /* Options valid for Samsung large page devices */
162 #define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG
163
164 /* Macros to identify the above */
165 #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG))
166 #define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ))
167
168 /* Non chip related options */
169 /* This option skips the bbt scan during initialization. */
170 #define NAND_SKIP_BBTSCAN 0x00010000
171 /*
172 * This option is defined if the board driver allocates its own buffers
173 * (e.g. because it needs them DMA-coherent).
174 */
175 #define NAND_OWN_BUFFERS 0x00020000
176 /* Chip may not exist, so silence any errors in scan */
177 #define NAND_SCAN_SILENT_NODEV 0x00040000
178 /*
179 * Autodetect nand buswidth with readid/onfi.
180 * This suppose the driver will configure the hardware in 8 bits mode
181 * when calling nand_scan_ident, and update its configuration
182 * before calling nand_scan_tail.
183 */
184 #define NAND_BUSWIDTH_AUTO 0x00080000
185 /*
186 * This option could be defined by controller drivers to protect against
187 * kmap'ed, vmalloc'ed highmem buffers being passed from upper layers
188 */
189 #define NAND_USE_BOUNCE_BUFFER 0x00100000
190
191 /* Options set by nand scan */
192 /* Nand scan has allocated controller struct */
193 #define NAND_CONTROLLER_ALLOC 0x80000000
194
195 /* Cell info constants */
196 #define NAND_CI_CHIPNR_MSK 0x03
197 #define NAND_CI_CELLTYPE_MSK 0x0C
198 #define NAND_CI_CELLTYPE_SHIFT 2
199
200 /* Keep gcc happy */
201 struct nand_chip;
202
203 /* ONFI features */
204 #define ONFI_FEATURE_16_BIT_BUS (1 << 0)
205 #define ONFI_FEATURE_EXT_PARAM_PAGE (1 << 7)
206
207 /* ONFI timing mode, used in both asynchronous and synchronous mode */
208 #define ONFI_TIMING_MODE_0 (1 << 0)
209 #define ONFI_TIMING_MODE_1 (1 << 1)
210 #define ONFI_TIMING_MODE_2 (1 << 2)
211 #define ONFI_TIMING_MODE_3 (1 << 3)
212 #define ONFI_TIMING_MODE_4 (1 << 4)
213 #define ONFI_TIMING_MODE_5 (1 << 5)
214 #define ONFI_TIMING_MODE_UNKNOWN (1 << 6)
215
216 /* ONFI feature address */
217 #define ONFI_FEATURE_ADDR_TIMING_MODE 0x1
218
219 /* Vendor-specific feature address (Micron) */
220 #define ONFI_FEATURE_ADDR_READ_RETRY 0x89
221
222 /* ONFI subfeature parameters length */
223 #define ONFI_SUBFEATURE_PARAM_LEN 4
224
225 /* ONFI optional commands SET/GET FEATURES supported? */
226 #define ONFI_OPT_CMD_SET_GET_FEATURES (1 << 2)
227
228 struct nand_onfi_params {
229 /* rev info and features block */
230 /* 'O' 'N' 'F' 'I' */
231 u8 sig[4];
232 __le16 revision;
233 __le16 features;
234 __le16 opt_cmd;
235 u8 reserved0[2];
236 __le16 ext_param_page_length; /* since ONFI 2.1 */
237 u8 num_of_param_pages; /* since ONFI 2.1 */
238 u8 reserved1[17];
239
240 /* manufacturer information block */
241 char manufacturer[12];
242 char model[20];
243 u8 jedec_id;
244 __le16 date_code;
245 u8 reserved2[13];
246
247 /* memory organization block */
248 __le32 byte_per_page;
249 __le16 spare_bytes_per_page;
250 __le32 data_bytes_per_ppage;
251 __le16 spare_bytes_per_ppage;
252 __le32 pages_per_block;
253 __le32 blocks_per_lun;
254 u8 lun_count;
255 u8 addr_cycles;
256 u8 bits_per_cell;
257 __le16 bb_per_lun;
258 __le16 block_endurance;
259 u8 guaranteed_good_blocks;
260 __le16 guaranteed_block_endurance;
261 u8 programs_per_page;
262 u8 ppage_attr;
263 u8 ecc_bits;
264 u8 interleaved_bits;
265 u8 interleaved_ops;
266 u8 reserved3[13];
267
268 /* electrical parameter block */
269 u8 io_pin_capacitance_max;
270 __le16 async_timing_mode;
271 __le16 program_cache_timing_mode;
272 __le16 t_prog;
273 __le16 t_bers;
274 __le16 t_r;
275 __le16 t_ccs;
276 __le16 src_sync_timing_mode;
277 __le16 src_ssync_features;
278 __le16 clk_pin_capacitance_typ;
279 __le16 io_pin_capacitance_typ;
280 __le16 input_pin_capacitance_typ;
281 u8 input_pin_capacitance_max;
282 u8 driver_strength_support;
283 __le16 t_int_r;
284 __le16 t_ald;
285 u8 reserved4[7];
286
287 /* vendor */
288 __le16 vendor_revision;
289 u8 vendor[88];
290
291 __le16 crc;
292 } __packed;
293
294 #define ONFI_CRC_BASE 0x4F4E
295
296 /* Extended ECC information Block Definition (since ONFI 2.1) */
297 struct onfi_ext_ecc_info {
298 u8 ecc_bits;
299 u8 codeword_size;
300 __le16 bb_per_lun;
301 __le16 block_endurance;
302 u8 reserved[2];
303 } __packed;
304
305 #define ONFI_SECTION_TYPE_0 0 /* Unused section. */
306 #define ONFI_SECTION_TYPE_1 1 /* for additional sections. */
307 #define ONFI_SECTION_TYPE_2 2 /* for ECC information. */
308 struct onfi_ext_section {
309 u8 type;
310 u8 length;
311 } __packed;
312
313 #define ONFI_EXT_SECTION_MAX 8
314
315 /* Extended Parameter Page Definition (since ONFI 2.1) */
316 struct onfi_ext_param_page {
317 __le16 crc;
318 u8 sig[4]; /* 'E' 'P' 'P' 'S' */
319 u8 reserved0[10];
320 struct onfi_ext_section sections[ONFI_EXT_SECTION_MAX];
321
322 /*
323 * The actual size of the Extended Parameter Page is in
324 * @ext_param_page_length of nand_onfi_params{}.
325 * The following are the variable length sections.
326 * So we do not add any fields below. Please see the ONFI spec.
327 */
328 } __packed;
329
330 struct nand_onfi_vendor_micron {
331 u8 two_plane_read;
332 u8 read_cache;
333 u8 read_unique_id;
334 u8 dq_imped;
335 u8 dq_imped_num_settings;
336 u8 dq_imped_feat_addr;
337 u8 rb_pulldown_strength;
338 u8 rb_pulldown_strength_feat_addr;
339 u8 rb_pulldown_strength_num_settings;
340 u8 otp_mode;
341 u8 otp_page_start;
342 u8 otp_data_prot_addr;
343 u8 otp_num_pages;
344 u8 otp_feat_addr;
345 u8 read_retry_options;
346 u8 reserved[72];
347 u8 param_revision;
348 } __packed;
349
350 struct jedec_ecc_info {
351 u8 ecc_bits;
352 u8 codeword_size;
353 __le16 bb_per_lun;
354 __le16 block_endurance;
355 u8 reserved[2];
356 } __packed;
357
358 /* JEDEC features */
359 #define JEDEC_FEATURE_16_BIT_BUS (1 << 0)
360
361 struct nand_jedec_params {
362 /* rev info and features block */
363 /* 'J' 'E' 'S' 'D' */
364 u8 sig[4];
365 __le16 revision;
366 __le16 features;
367 u8 opt_cmd[3];
368 __le16 sec_cmd;
369 u8 num_of_param_pages;
370 u8 reserved0[18];
371
372 /* manufacturer information block */
373 char manufacturer[12];
374 char model[20];
375 u8 jedec_id[6];
376 u8 reserved1[10];
377
378 /* memory organization block */
379 __le32 byte_per_page;
380 __le16 spare_bytes_per_page;
381 u8 reserved2[6];
382 __le32 pages_per_block;
383 __le32 blocks_per_lun;
384 u8 lun_count;
385 u8 addr_cycles;
386 u8 bits_per_cell;
387 u8 programs_per_page;
388 u8 multi_plane_addr;
389 u8 multi_plane_op_attr;
390 u8 reserved3[38];
391
392 /* electrical parameter block */
393 __le16 async_sdr_speed_grade;
394 __le16 toggle_ddr_speed_grade;
395 __le16 sync_ddr_speed_grade;
396 u8 async_sdr_features;
397 u8 toggle_ddr_features;
398 u8 sync_ddr_features;
399 __le16 t_prog;
400 __le16 t_bers;
401 __le16 t_r;
402 __le16 t_r_multi_plane;
403 __le16 t_ccs;
404 __le16 io_pin_capacitance_typ;
405 __le16 input_pin_capacitance_typ;
406 __le16 clk_pin_capacitance_typ;
407 u8 driver_strength_support;
408 __le16 t_ald;
409 u8 reserved4[36];
410
411 /* ECC and endurance block */
412 u8 guaranteed_good_blocks;
413 __le16 guaranteed_block_endurance;
414 struct jedec_ecc_info ecc_info[4];
415 u8 reserved5[29];
416
417 /* reserved */
418 u8 reserved6[148];
419
420 /* vendor */
421 __le16 vendor_rev_num;
422 u8 reserved7[88];
423
424 /* CRC for Parameter Page */
425 __le16 crc;
426 } __packed;
427
428 /**
429 * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices
430 * @lock: protection lock
431 * @active: the mtd device which holds the controller currently
432 * @wq: wait queue to sleep on if a NAND operation is in
433 * progress used instead of the per chip wait queue
434 * when a hw controller is available.
435 */
436 struct nand_hw_control {
437 spinlock_t lock;
438 struct nand_chip *active;
439 wait_queue_head_t wq;
440 };
441
442 /**
443 * struct nand_ecc_ctrl - Control structure for ECC
444 * @mode: ECC mode
445 * @steps: number of ECC steps per page
446 * @size: data bytes per ECC step
447 * @bytes: ECC bytes per step
448 * @strength: max number of correctible bits per ECC step
449 * @total: total number of ECC bytes per page
450 * @prepad: padding information for syndrome based ECC generators
451 * @postpad: padding information for syndrome based ECC generators
452 * @layout: ECC layout control struct pointer
453 * @priv: pointer to private ECC control data
454 * @hwctl: function to control hardware ECC generator. Must only
455 * be provided if an hardware ECC is available
456 * @calculate: function for ECC calculation or readback from ECC hardware
457 * @correct: function for ECC correction, matching to ECC generator (sw/hw)
458 * @read_page_raw: function to read a raw page without ECC
459 * @write_page_raw: function to write a raw page without ECC
460 * @read_page: function to read a page according to the ECC generator
461 * requirements; returns maximum number of bitflips corrected in
462 * any single ECC step, 0 if bitflips uncorrectable, -EIO hw error
463 * @read_subpage: function to read parts of the page covered by ECC;
464 * returns same as read_page()
465 * @write_subpage: function to write parts of the page covered by ECC.
466 * @write_page: function to write a page according to the ECC generator
467 * requirements.
468 * @write_oob_raw: function to write chip OOB data without ECC
469 * @read_oob_raw: function to read chip OOB data without ECC
470 * @read_oob: function to read chip OOB data
471 * @write_oob: function to write chip OOB data
472 */
473 struct nand_ecc_ctrl {
474 nand_ecc_modes_t mode;
475 int steps;
476 int size;
477 int bytes;
478 int total;
479 int strength;
480 int prepad;
481 int postpad;
482 struct nand_ecclayout *layout;
483 void *priv;
484 void (*hwctl)(struct mtd_info *mtd, int mode);
485 int (*calculate)(struct mtd_info *mtd, const uint8_t *dat,
486 uint8_t *ecc_code);
487 int (*correct)(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc,
488 uint8_t *calc_ecc);
489 int (*read_page_raw)(struct mtd_info *mtd, struct nand_chip *chip,
490 uint8_t *buf, int oob_required, int page);
491 int (*write_page_raw)(struct mtd_info *mtd, struct nand_chip *chip,
492 const uint8_t *buf, int oob_required);
493 int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip,
494 uint8_t *buf, int oob_required, int page);
495 int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip,
496 uint32_t offs, uint32_t len, uint8_t *buf, int page);
497 int (*write_subpage)(struct mtd_info *mtd, struct nand_chip *chip,
498 uint32_t offset, uint32_t data_len,
499 const uint8_t *data_buf, int oob_required);
500 int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
501 const uint8_t *buf, int oob_required);
502 int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip,
503 int page);
504 int (*read_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip,
505 int page);
506 int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page);
507 int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip,
508 int page);
509 };
510
511 /**
512 * struct nand_buffers - buffer structure for read/write
513 * @ecccalc: buffer pointer for calculated ECC, size is oobsize.
514 * @ecccode: buffer pointer for ECC read from flash, size is oobsize.
515 * @databuf: buffer pointer for data, size is (page size + oobsize).
516 *
517 * Do not change the order of buffers. databuf and oobrbuf must be in
518 * consecutive order.
519 */
520 struct nand_buffers {
521 uint8_t *ecccalc;
522 uint8_t *ecccode;
523 uint8_t *databuf;
524 };
525
526 /**
527 * struct nand_chip - NAND Private Flash Chip Data
528 * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the
529 * flash device
530 * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the
531 * flash device.
532 * @read_byte: [REPLACEABLE] read one byte from the chip
533 * @read_word: [REPLACEABLE] read one word from the chip
534 * @write_byte: [REPLACEABLE] write a single byte to the chip on the
535 * low 8 I/O lines
536 * @write_buf: [REPLACEABLE] write data from the buffer to the chip
537 * @read_buf: [REPLACEABLE] read data from the chip into the buffer
538 * @select_chip: [REPLACEABLE] select chip nr
539 * @block_bad: [REPLACEABLE] check if a block is bad, using OOB markers
540 * @block_markbad: [REPLACEABLE] mark a block bad
541 * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific function for controlling
542 * ALE/CLE/nCE. Also used to write command and address
543 * @init_size: [BOARDSPECIFIC] hardwarespecific function for setting
544 * mtd->oobsize, mtd->writesize and so on.
545 * @id_data contains the 8 bytes values of NAND_CMD_READID.
546 * Return with the bus width.
547 * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing
548 * device ready/busy line. If set to NULL no access to
549 * ready/busy is available and the ready/busy information
550 * is read from the chip status register.
551 * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing
552 * commands to the chip.
553 * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on
554 * ready.
555 * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for
556 * setting the read-retry mode. Mostly needed for MLC NAND.
557 * @ecc: [BOARDSPECIFIC] ECC control structure
558 * @buffers: buffer structure for read/write
559 * @hwcontrol: platform-specific hardware control structure
560 * @erase: [REPLACEABLE] erase function
561 * @scan_bbt: [REPLACEABLE] function to scan bad block table
562 * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring
563 * data from array to read regs (tR).
564 * @state: [INTERN] the current state of the NAND device
565 * @oob_poi: "poison value buffer," used for laying out OOB data
566 * before writing
567 * @page_shift: [INTERN] number of address bits in a page (column
568 * address bits).
569 * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock
570 * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry
571 * @chip_shift: [INTERN] number of address bits in one chip
572 * @options: [BOARDSPECIFIC] various chip options. They can partly
573 * be set to inform nand_scan about special functionality.
574 * See the defines for further explanation.
575 * @bbt_options: [INTERN] bad block specific options. All options used
576 * here must come from bbm.h. By default, these options
577 * will be copied to the appropriate nand_bbt_descr's.
578 * @badblockpos: [INTERN] position of the bad block marker in the oob
579 * area.
580 * @badblockbits: [INTERN] minimum number of set bits in a good block's
581 * bad block marker position; i.e., BBM == 11110111b is
582 * not bad when badblockbits == 7
583 * @bits_per_cell: [INTERN] number of bits per cell. i.e., 1 means SLC.
584 * @ecc_strength_ds: [INTERN] ECC correctability from the datasheet.
585 * Minimum amount of bit errors per @ecc_step_ds guaranteed
586 * to be correctable. If unknown, set to zero.
587 * @ecc_step_ds: [INTERN] ECC step required by the @ecc_strength_ds,
588 * also from the datasheet. It is the recommended ECC step
589 * size, if known; if unknown, set to zero.
590 * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is
591 * either deduced from the datasheet if the NAND
592 * chip is not ONFI compliant or set to 0 if it is
593 * (an ONFI chip is always configured in mode 0
594 * after a NAND reset)
595 * @numchips: [INTERN] number of physical chips
596 * @chipsize: [INTERN] the size of one chip for multichip arrays
597 * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1
598 * @pagebuf: [INTERN] holds the pagenumber which is currently in
599 * data_buf.
600 * @pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is
601 * currently in data_buf.
602 * @subpagesize: [INTERN] holds the subpagesize
603 * @onfi_version: [INTERN] holds the chip ONFI version (BCD encoded),
604 * non 0 if ONFI supported.
605 * @jedec_version: [INTERN] holds the chip JEDEC version (BCD encoded),
606 * non 0 if JEDEC supported.
607 * @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is
608 * supported, 0 otherwise.
609 * @jedec_params: [INTERN] holds the JEDEC parameter page when JEDEC is
610 * supported, 0 otherwise.
611 * @read_retries: [INTERN] the number of read retry modes supported
612 * @onfi_set_features: [REPLACEABLE] set the features for ONFI nand
613 * @onfi_get_features: [REPLACEABLE] get the features for ONFI nand
614 * @bbt: [INTERN] bad block table pointer
615 * @bbt_td: [REPLACEABLE] bad block table descriptor for flash
616 * lookup.
617 * @bbt_md: [REPLACEABLE] bad block table mirror descriptor
618 * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial
619 * bad block scan.
620 * @controller: [REPLACEABLE] a pointer to a hardware controller
621 * structure which is shared among multiple independent
622 * devices.
623 * @priv: [OPTIONAL] pointer to private chip data
624 * @errstat: [OPTIONAL] hardware specific function to perform
625 * additional error status checks (determine if errors are
626 * correctable).
627 * @write_page: [REPLACEABLE] High-level page write function
628 */
629
630 struct nand_chip {
631 void __iomem *IO_ADDR_R;
632 void __iomem *IO_ADDR_W;
633
634 uint8_t (*read_byte)(struct mtd_info *mtd);
635 u16 (*read_word)(struct mtd_info *mtd);
636 void (*write_byte)(struct mtd_info *mtd, uint8_t byte);
637 void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
638 void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
639 void (*select_chip)(struct mtd_info *mtd, int chip);
640 int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip);
641 int (*block_markbad)(struct mtd_info *mtd, loff_t ofs);
642 void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl);
643 int (*init_size)(struct mtd_info *mtd, struct nand_chip *this,
644 u8 *id_data);
645 int (*dev_ready)(struct mtd_info *mtd);
646 void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column,
647 int page_addr);
648 int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this);
649 int (*erase)(struct mtd_info *mtd, int page);
650 int (*scan_bbt)(struct mtd_info *mtd);
651 int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state,
652 int status, int page);
653 int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
654 uint32_t offset, int data_len, const uint8_t *buf,
655 int oob_required, int page, int cached, int raw);
656 int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip,
657 int feature_addr, uint8_t *subfeature_para);
658 int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip,
659 int feature_addr, uint8_t *subfeature_para);
660 int (*setup_read_retry)(struct mtd_info *mtd, int retry_mode);
661
662 int chip_delay;
663 unsigned int options;
664 unsigned int bbt_options;
665
666 int page_shift;
667 int phys_erase_shift;
668 int bbt_erase_shift;
669 int chip_shift;
670 int numchips;
671 uint64_t chipsize;
672 int pagemask;
673 int pagebuf;
674 unsigned int pagebuf_bitflips;
675 int subpagesize;
676 uint8_t bits_per_cell;
677 uint16_t ecc_strength_ds;
678 uint16_t ecc_step_ds;
679 int onfi_timing_mode_default;
680 int badblockpos;
681 int badblockbits;
682
683 int onfi_version;
684 int jedec_version;
685 union {
686 struct nand_onfi_params onfi_params;
687 struct nand_jedec_params jedec_params;
688 };
689
690 int read_retries;
691
692 flstate_t state;
693
694 uint8_t *oob_poi;
695 struct nand_hw_control *controller;
696
697 struct nand_ecc_ctrl ecc;
698 struct nand_buffers *buffers;
699 struct nand_hw_control hwcontrol;
700
701 uint8_t *bbt;
702 struct nand_bbt_descr *bbt_td;
703 struct nand_bbt_descr *bbt_md;
704
705 struct nand_bbt_descr *badblock_pattern;
706
707 void *priv;
708 };
709
710 /*
711 * NAND Flash Manufacturer ID Codes
712 */
713 #define NAND_MFR_TOSHIBA 0x98
714 #define NAND_MFR_SAMSUNG 0xec
715 #define NAND_MFR_FUJITSU 0x04
716 #define NAND_MFR_NATIONAL 0x8f
717 #define NAND_MFR_RENESAS 0x07
718 #define NAND_MFR_STMICRO 0x20
719 #define NAND_MFR_HYNIX 0xad
720 #define NAND_MFR_MICRON 0x2c
721 #define NAND_MFR_AMD 0x01
722 #define NAND_MFR_MACRONIX 0xc2
723 #define NAND_MFR_EON 0x92
724 #define NAND_MFR_SANDISK 0x45
725 #define NAND_MFR_INTEL 0x89
726
727 /* The maximum expected count of bytes in the NAND ID sequence */
728 #define NAND_MAX_ID_LEN 8
729
730 /*
731 * A helper for defining older NAND chips where the second ID byte fully
732 * defined the chip, including the geometry (chip size, eraseblock size, page
733 * size). All these chips have 512 bytes NAND page size.
734 */
735 #define LEGACY_ID_NAND(nm, devid, chipsz, erasesz, opts) \
736 { .name = (nm), {{ .dev_id = (devid) }}, .pagesize = 512, \
737 .chipsize = (chipsz), .erasesize = (erasesz), .options = (opts) }
738
739 /*
740 * A helper for defining newer chips which report their page size and
741 * eraseblock size via the extended ID bytes.
742 *
743 * The real difference between LEGACY_ID_NAND and EXTENDED_ID_NAND is that with
744 * EXTENDED_ID_NAND, manufacturers overloaded the same device ID so that the
745 * device ID now only represented a particular total chip size (and voltage,
746 * buswidth), and the page size, eraseblock size, and OOB size could vary while
747 * using the same device ID.
748 */
749 #define EXTENDED_ID_NAND(nm, devid, chipsz, opts) \
750 { .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \
751 .options = (opts) }
752
753 #define NAND_ECC_INFO(_strength, _step) \
754 { .strength_ds = (_strength), .step_ds = (_step) }
755 #define NAND_ECC_STRENGTH(type) ((type)->ecc.strength_ds)
756 #define NAND_ECC_STEP(type) ((type)->ecc.step_ds)
757
758 /**
759 * struct nand_flash_dev - NAND Flash Device ID Structure
760 * @name: a human-readable name of the NAND chip
761 * @dev_id: the device ID (the second byte of the full chip ID array)
762 * @mfr_id: manufecturer ID part of the full chip ID array (refers the same
763 * memory address as @id[0])
764 * @dev_id: device ID part of the full chip ID array (refers the same memory
765 * address as @id[1])
766 * @id: full device ID array
767 * @pagesize: size of the NAND page in bytes; if 0, then the real page size (as
768 * well as the eraseblock size) is determined from the extended NAND
769 * chip ID array)
770 * @chipsize: total chip size in MiB
771 * @erasesize: eraseblock size in bytes (determined from the extended ID if 0)
772 * @options: stores various chip bit options
773 * @id_len: The valid length of the @id.
774 * @oobsize: OOB size
775 * @ecc: ECC correctability and step information from the datasheet.
776 * @ecc.strength_ds: The ECC correctability from the datasheet, same as the
777 * @ecc_strength_ds in nand_chip{}.
778 * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the
779 * @ecc_step_ds in nand_chip{}, also from the datasheet.
780 * For example, the "4bit ECC for each 512Byte" can be set with
781 * NAND_ECC_INFO(4, 512).
782 * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND
783 * reset. Should be deduced from timings described
784 * in the datasheet.
785 *
786 */
787 struct nand_flash_dev {
788 char *name;
789 union {
790 struct {
791 uint8_t mfr_id;
792 uint8_t dev_id;
793 };
794 uint8_t id[NAND_MAX_ID_LEN];
795 };
796 unsigned int pagesize;
797 unsigned int chipsize;
798 unsigned int erasesize;
799 unsigned int options;
800 uint16_t id_len;
801 uint16_t oobsize;
802 struct {
803 uint16_t strength_ds;
804 uint16_t step_ds;
805 } ecc;
806 int onfi_timing_mode_default;
807 };
808
809 /**
810 * struct nand_manufacturers - NAND Flash Manufacturer ID Structure
811 * @name: Manufacturer name
812 * @id: manufacturer ID code of device.
813 */
814 struct nand_manufacturers {
815 int id;
816 char *name;
817 };
818
819 extern struct nand_flash_dev nand_flash_ids[];
820 extern struct nand_manufacturers nand_manuf_ids[];
821
822 extern int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd);
823 extern int nand_default_bbt(struct mtd_info *mtd);
824 extern int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs);
825 extern int nand_isreserved_bbt(struct mtd_info *mtd, loff_t offs);
826 extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt);
827 extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
828 int allowbbt);
829 extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len,
830 size_t *retlen, uint8_t *buf);
831
832 /**
833 * struct platform_nand_chip - chip level device structure
834 * @nr_chips: max. number of chips to scan for
835 * @chip_offset: chip number offset
836 * @nr_partitions: number of partitions pointed to by partitions (or zero)
837 * @partitions: mtd partition list
838 * @chip_delay: R/B delay value in us
839 * @options: Option flags, e.g. 16bit buswidth
840 * @bbt_options: BBT option flags, e.g. NAND_BBT_USE_FLASH
841 * @ecclayout: ECC layout info structure
842 * @part_probe_types: NULL-terminated array of probe types
843 */
844 struct platform_nand_chip {
845 int nr_chips;
846 int chip_offset;
847 int nr_partitions;
848 struct mtd_partition *partitions;
849 struct nand_ecclayout *ecclayout;
850 int chip_delay;
851 unsigned int options;
852 unsigned int bbt_options;
853 const char **part_probe_types;
854 };
855
856 /* Keep gcc happy */
857 struct platform_device;
858
859 /**
860 * struct platform_nand_ctrl - controller level device structure
861 * @probe: platform specific function to probe/setup hardware
862 * @remove: platform specific function to remove/teardown hardware
863 * @hwcontrol: platform specific hardware control structure
864 * @dev_ready: platform specific function to read ready/busy pin
865 * @select_chip: platform specific chip select function
866 * @cmd_ctrl: platform specific function for controlling
867 * ALE/CLE/nCE. Also used to write command and address
868 * @write_buf: platform specific function for write buffer
869 * @read_buf: platform specific function for read buffer
870 * @read_byte: platform specific function to read one byte from chip
871 * @priv: private data to transport driver specific settings
872 *
873 * All fields are optional and depend on the hardware driver requirements
874 */
875 struct platform_nand_ctrl {
876 int (*probe)(struct platform_device *pdev);
877 void (*remove)(struct platform_device *pdev);
878 void (*hwcontrol)(struct mtd_info *mtd, int cmd);
879 int (*dev_ready)(struct mtd_info *mtd);
880 void (*select_chip)(struct mtd_info *mtd, int chip);
881 void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl);
882 void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
883 void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
884 unsigned char (*read_byte)(struct mtd_info *mtd);
885 void *priv;
886 };
887
888 /**
889 * struct platform_nand_data - container structure for platform-specific data
890 * @chip: chip level chip structure
891 * @ctrl: controller level device structure
892 */
893 struct platform_nand_data {
894 struct platform_nand_chip chip;
895 struct platform_nand_ctrl ctrl;
896 };
897
898 /* Some helpers to access the data structures */
899 static inline
get_platform_nandchip(struct mtd_info * mtd)900 struct platform_nand_chip *get_platform_nandchip(struct mtd_info *mtd)
901 {
902 struct nand_chip *chip = mtd->priv;
903
904 return chip->priv;
905 }
906
907 /* return the supported features. */
onfi_feature(struct nand_chip * chip)908 static inline int onfi_feature(struct nand_chip *chip)
909 {
910 return chip->onfi_version ? le16_to_cpu(chip->onfi_params.features) : 0;
911 }
912
913 /* return the supported asynchronous timing mode. */
onfi_get_async_timing_mode(struct nand_chip * chip)914 static inline int onfi_get_async_timing_mode(struct nand_chip *chip)
915 {
916 if (!chip->onfi_version)
917 return ONFI_TIMING_MODE_UNKNOWN;
918 return le16_to_cpu(chip->onfi_params.async_timing_mode);
919 }
920
921 /* return the supported synchronous timing mode. */
onfi_get_sync_timing_mode(struct nand_chip * chip)922 static inline int onfi_get_sync_timing_mode(struct nand_chip *chip)
923 {
924 if (!chip->onfi_version)
925 return ONFI_TIMING_MODE_UNKNOWN;
926 return le16_to_cpu(chip->onfi_params.src_sync_timing_mode);
927 }
928
929 /*
930 * Check if it is a SLC nand.
931 * The !nand_is_slc() can be used to check the MLC/TLC nand chips.
932 * We do not distinguish the MLC and TLC now.
933 */
nand_is_slc(struct nand_chip * chip)934 static inline bool nand_is_slc(struct nand_chip *chip)
935 {
936 return chip->bits_per_cell == 1;
937 }
938
939 /**
940 * Check if the opcode's address should be sent only on the lower 8 bits
941 * @command: opcode to check
942 */
nand_opcode_8bits(unsigned int command)943 static inline int nand_opcode_8bits(unsigned int command)
944 {
945 switch (command) {
946 case NAND_CMD_READID:
947 case NAND_CMD_PARAM:
948 case NAND_CMD_GET_FEATURES:
949 case NAND_CMD_SET_FEATURES:
950 return 1;
951 default:
952 break;
953 }
954 return 0;
955 }
956
957 /* return the supported JEDEC features. */
jedec_feature(struct nand_chip * chip)958 static inline int jedec_feature(struct nand_chip *chip)
959 {
960 return chip->jedec_version ? le16_to_cpu(chip->jedec_params.features)
961 : 0;
962 }
963
964 /*
965 * struct nand_sdr_timings - SDR NAND chip timings
966 *
967 * This struct defines the timing requirements of a SDR NAND chip.
968 * These informations can be found in every NAND datasheets and the timings
969 * meaning are described in the ONFI specifications:
970 * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing
971 * Parameters)
972 *
973 * All these timings are expressed in picoseconds.
974 */
975
976 struct nand_sdr_timings {
977 u32 tALH_min;
978 u32 tADL_min;
979 u32 tALS_min;
980 u32 tAR_min;
981 u32 tCEA_max;
982 u32 tCEH_min;
983 u32 tCH_min;
984 u32 tCHZ_max;
985 u32 tCLH_min;
986 u32 tCLR_min;
987 u32 tCLS_min;
988 u32 tCOH_min;
989 u32 tCS_min;
990 u32 tDH_min;
991 u32 tDS_min;
992 u32 tFEAT_max;
993 u32 tIR_min;
994 u32 tITC_max;
995 u32 tRC_min;
996 u32 tREA_max;
997 u32 tREH_min;
998 u32 tRHOH_min;
999 u32 tRHW_min;
1000 u32 tRHZ_max;
1001 u32 tRLOH_min;
1002 u32 tRP_min;
1003 u32 tRR_min;
1004 u64 tRST_max;
1005 u32 tWB_max;
1006 u32 tWC_min;
1007 u32 tWH_min;
1008 u32 tWHR_min;
1009 u32 tWP_min;
1010 u32 tWW_min;
1011 };
1012
1013 /* get timing characteristics from ONFI timing mode. */
1014 const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode);
1015 #endif /* __LINUX_MTD_NAND_H */
1016