1 /*
2 * This is the configuration for SSV Dil/NetPC DNP/5370 board.
3 *
4 * DIL module: http://www.dilnetpc.com/dnp0086.htm
5 * SK28 (starter kit): http://www.dilnetpc.com/dnp0088.htm
6 *
7 * Copyright 2010 3ality Digital Systems
8 * Copyright 2005 National ICT Australia (NICTA)
9 * Copyright 2004-2006 Analog Devices Inc.
10 *
11 * Licensed under the GPL-2 or later.
12 */
13
14 #include <linux/device.h>
15 #include <linux/export.h>
16 #include <linux/kernel.h>
17 #include <linux/platform_device.h>
18 #include <linux/io.h>
19 #include <linux/mtd/mtd.h>
20 #include <linux/mtd/nand.h>
21 #include <linux/mtd/partitions.h>
22 #include <linux/mtd/plat-ram.h>
23 #include <linux/mtd/physmap.h>
24 #include <linux/spi/spi.h>
25 #include <linux/spi/flash.h>
26 #include <linux/irq.h>
27 #include <linux/interrupt.h>
28 #include <linux/i2c.h>
29 #include <linux/spi/mmc_spi.h>
30 #include <linux/phy.h>
31 #include <asm/dma.h>
32 #include <asm/bfin5xx_spi.h>
33 #include <asm/reboot.h>
34 #include <asm/portmux.h>
35 #include <asm/dpmc.h>
36
37 /*
38 * Name the Board for the /proc/cpuinfo
39 */
40 const char bfin_board_name[] = "DNP/5370";
41 #define FLASH_MAC 0x202f0000
42 #define CONFIG_MTD_PHYSMAP_LEN 0x300000
43
44 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
45 static struct platform_device rtc_device = {
46 .name = "rtc-bfin",
47 .id = -1,
48 };
49 #endif
50
51 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
52 #include <linux/bfin_mac.h>
53 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
54
55 static struct bfin_phydev_platform_data bfin_phydev_data[] = {
56 {
57 .addr = 1,
58 .irq = PHY_POLL, /* IRQ_MAC_PHYINT */
59 },
60 };
61
62 static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
63 .phydev_number = 1,
64 .phydev_data = bfin_phydev_data,
65 .phy_mode = PHY_INTERFACE_MODE_RMII,
66 .mac_peripherals = bfin_mac_peripherals,
67 };
68
69 static struct platform_device bfin_mii_bus = {
70 .name = "bfin_mii_bus",
71 .dev = {
72 .platform_data = &bfin_mii_bus_data,
73 }
74 };
75
76 static struct platform_device bfin_mac_device = {
77 .name = "bfin_mac",
78 .dev = {
79 .platform_data = &bfin_mii_bus,
80 }
81 };
82 #endif
83
84 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
85 static struct mtd_partition asmb_flash_partitions[] = {
86 {
87 .name = "bootloader(nor)",
88 .size = 0x30000,
89 .offset = 0,
90 }, {
91 .name = "linux kernel and rootfs(nor)",
92 .size = 0x300000 - 0x30000 - 0x10000,
93 .offset = MTDPART_OFS_APPEND,
94 }, {
95 .name = "MAC address(nor)",
96 .size = 0x10000,
97 .offset = MTDPART_OFS_APPEND,
98 .mask_flags = MTD_WRITEABLE,
99 }
100 };
101
102 static struct physmap_flash_data asmb_flash_data = {
103 .width = 1,
104 .parts = asmb_flash_partitions,
105 .nr_parts = ARRAY_SIZE(asmb_flash_partitions),
106 };
107
108 static struct resource asmb_flash_resource = {
109 .start = 0x20000000,
110 .end = 0x202fffff,
111 .flags = IORESOURCE_MEM,
112 };
113
114 /* 4 MB NOR flash attached to async memory banks 0-2,
115 * therefore only 3 MB visible.
116 */
117 static struct platform_device asmb_flash_device = {
118 .name = "physmap-flash",
119 .id = 0,
120 .dev = {
121 .platform_data = &asmb_flash_data,
122 },
123 .num_resources = 1,
124 .resource = &asmb_flash_resource,
125 };
126 #endif
127
128 #if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
129
130 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
131
132 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
133 .enable_dma = 0, /* use no dma transfer with this chip*/
134 };
135
136 #endif
137
138 #if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
139 /* This mapping is for at45db642 it has 1056 page size,
140 * partition size and offset should be page aligned
141 */
142 static struct mtd_partition bfin_spi_dataflash_partitions[] = {
143 {
144 .name = "JFFS2 dataflash(nor)",
145 #ifdef CONFIG_MTD_PAGESIZE_1024
146 .offset = 0x40000,
147 .size = 0x7C0000,
148 #else
149 .offset = 0x0,
150 .size = 0x840000,
151 #endif
152 }
153 };
154
155 static struct flash_platform_data bfin_spi_dataflash_data = {
156 .name = "mtd_dataflash",
157 .parts = bfin_spi_dataflash_partitions,
158 .nr_parts = ARRAY_SIZE(bfin_spi_dataflash_partitions),
159 .type = "mtd_dataflash",
160 };
161
162 static struct bfin5xx_spi_chip spi_dataflash_chip_info = {
163 .enable_dma = 0, /* use no dma transfer with this chip*/
164 };
165 #endif
166
167 static struct spi_board_info bfin_spi_board_info[] __initdata = {
168 /* SD/MMC card reader at SPI bus */
169 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
170 {
171 .modalias = "mmc_spi",
172 .max_speed_hz = 20000000,
173 .bus_num = 0,
174 .chip_select = 1,
175 .controller_data = &mmc_spi_chip_info,
176 .mode = SPI_MODE_3,
177 },
178 #endif
179
180 /* 8 Megabyte Atmel NOR flash chip at SPI bus */
181 #if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
182 {
183 .modalias = "mtd_dataflash",
184 .max_speed_hz = 16700000,
185 .bus_num = 0,
186 .chip_select = 2,
187 .platform_data = &bfin_spi_dataflash_data,
188 .controller_data = &spi_dataflash_chip_info,
189 .mode = SPI_MODE_3, /* SPI_CPHA and SPI_CPOL */
190 },
191 #endif
192 };
193
194 /* SPI controller data */
195 /* SPI (0) */
196 static struct resource bfin_spi0_resource[] = {
197 [0] = {
198 .start = SPI0_REGBASE,
199 .end = SPI0_REGBASE + 0xFF,
200 .flags = IORESOURCE_MEM,
201 },
202 [1] = {
203 .start = CH_SPI,
204 .end = CH_SPI,
205 .flags = IORESOURCE_DMA,
206 },
207 [2] = {
208 .start = IRQ_SPI,
209 .end = IRQ_SPI,
210 .flags = IORESOURCE_IRQ,
211 },
212 };
213
214 static struct bfin5xx_spi_master spi_bfin_master_info = {
215 .num_chipselect = 8,
216 .enable_dma = 1, /* master has the ability to do dma transfer */
217 .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
218 };
219
220 static struct platform_device spi_bfin_master_device = {
221 .name = "bfin-spi",
222 .id = 0, /* Bus number */
223 .num_resources = ARRAY_SIZE(bfin_spi0_resource),
224 .resource = bfin_spi0_resource,
225 .dev = {
226 .platform_data = &spi_bfin_master_info, /* Passed to driver */
227 },
228 };
229 #endif
230
231 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
232 #ifdef CONFIG_SERIAL_BFIN_UART0
233 static struct resource bfin_uart0_resources[] = {
234 {
235 .start = UART0_THR,
236 .end = UART0_GCTL+2,
237 .flags = IORESOURCE_MEM,
238 },
239 {
240 .start = IRQ_UART0_TX,
241 .end = IRQ_UART0_TX,
242 .flags = IORESOURCE_IRQ,
243 },
244 {
245 .start = IRQ_UART0_RX,
246 .end = IRQ_UART0_RX,
247 .flags = IORESOURCE_IRQ,
248 },
249 {
250 .start = IRQ_UART0_ERROR,
251 .end = IRQ_UART0_ERROR,
252 .flags = IORESOURCE_IRQ,
253 },
254 {
255 .start = CH_UART0_TX,
256 .end = CH_UART0_TX,
257 .flags = IORESOURCE_DMA,
258 },
259 {
260 .start = CH_UART0_RX,
261 .end = CH_UART0_RX,
262 .flags = IORESOURCE_DMA,
263 },
264 };
265
266 static unsigned short bfin_uart0_peripherals[] = {
267 P_UART0_TX, P_UART0_RX, 0
268 };
269
270 static struct platform_device bfin_uart0_device = {
271 .name = "bfin-uart",
272 .id = 0,
273 .num_resources = ARRAY_SIZE(bfin_uart0_resources),
274 .resource = bfin_uart0_resources,
275 .dev = {
276 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
277 },
278 };
279 #endif
280
281 #ifdef CONFIG_SERIAL_BFIN_UART1
282 static struct resource bfin_uart1_resources[] = {
283 {
284 .start = UART1_THR,
285 .end = UART1_GCTL+2,
286 .flags = IORESOURCE_MEM,
287 },
288 {
289 .start = IRQ_UART1_TX,
290 .end = IRQ_UART1_TX,
291 .flags = IORESOURCE_IRQ,
292 },
293 {
294 .start = IRQ_UART1_RX,
295 .end = IRQ_UART1_RX,
296 .flags = IORESOURCE_IRQ,
297 },
298 {
299 .start = IRQ_UART1_ERROR,
300 .end = IRQ_UART1_ERROR,
301 .flags = IORESOURCE_IRQ,
302 },
303 {
304 .start = CH_UART1_TX,
305 .end = CH_UART1_TX,
306 .flags = IORESOURCE_DMA,
307 },
308 {
309 .start = CH_UART1_RX,
310 .end = CH_UART1_RX,
311 .flags = IORESOURCE_DMA,
312 },
313 };
314
315 static unsigned short bfin_uart1_peripherals[] = {
316 P_UART1_TX, P_UART1_RX, 0
317 };
318
319 static struct platform_device bfin_uart1_device = {
320 .name = "bfin-uart",
321 .id = 1,
322 .num_resources = ARRAY_SIZE(bfin_uart1_resources),
323 .resource = bfin_uart1_resources,
324 .dev = {
325 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
326 },
327 };
328 #endif
329 #endif
330
331 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
332 static struct resource bfin_twi0_resource[] = {
333 [0] = {
334 .start = TWI0_REGBASE,
335 .end = TWI0_REGBASE + 0xff,
336 .flags = IORESOURCE_MEM,
337 },
338 [1] = {
339 .start = IRQ_TWI,
340 .end = IRQ_TWI,
341 .flags = IORESOURCE_IRQ,
342 },
343 };
344
345 static struct platform_device i2c_bfin_twi_device = {
346 .name = "i2c-bfin-twi",
347 .id = 0,
348 .num_resources = ARRAY_SIZE(bfin_twi0_resource),
349 .resource = bfin_twi0_resource,
350 };
351 #endif
352
353 static struct platform_device *dnp5370_devices[] __initdata = {
354
355 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
356 #ifdef CONFIG_SERIAL_BFIN_UART0
357 &bfin_uart0_device,
358 #endif
359 #ifdef CONFIG_SERIAL_BFIN_UART1
360 &bfin_uart1_device,
361 #endif
362 #endif
363
364 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
365 &asmb_flash_device,
366 #endif
367
368 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
369 &bfin_mii_bus,
370 &bfin_mac_device,
371 #endif
372
373 #if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
374 &spi_bfin_master_device,
375 #endif
376
377 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
378 &i2c_bfin_twi_device,
379 #endif
380
381 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
382 &rtc_device,
383 #endif
384
385 };
386
dnp5370_init(void)387 static int __init dnp5370_init(void)
388 {
389 printk(KERN_INFO "DNP/5370: registering device resources\n");
390 platform_add_devices(dnp5370_devices, ARRAY_SIZE(dnp5370_devices));
391 printk(KERN_INFO "DNP/5370: registering %zu SPI slave devices\n",
392 ARRAY_SIZE(bfin_spi_board_info));
393 spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
394 printk(KERN_INFO "DNP/5370: MAC %pM\n", (void *)FLASH_MAC);
395 return 0;
396 }
397 arch_initcall(dnp5370_init);
398
399 /*
400 * Currently the MAC address is saved in Flash by U-Boot
401 */
bfin_get_ether_addr(char * addr)402 int bfin_get_ether_addr(char *addr)
403 {
404 *(u32 *)(&(addr[0])) = bfin_read32(FLASH_MAC);
405 *(u16 *)(&(addr[4])) = bfin_read16(FLASH_MAC + 4);
406 return 0;
407 }
408 EXPORT_SYMBOL(bfin_get_ether_addr);
409