1 /* 2 * Copyright (C) 2011 Marvell International Ltd. All rights reserved. 3 * 4 * This program is free software; you can redistribute it and/or modify it 5 * under the terms of the GNU General Public License as published by the 6 * Free Software Foundation; either version 2 of the License, or (at your 7 * option) any later version. 8 */ 9 10 #ifndef __MV_UDC_H 11 #define __MV_UDC_H 12 13 #define VUSBHS_MAX_PORTS 8 14 15 #define DQH_ALIGNMENT 2048 16 #define DTD_ALIGNMENT 64 17 #define DMA_BOUNDARY 4096 18 19 #define EP_DIR_IN 1 20 #define EP_DIR_OUT 0 21 22 #define DMA_ADDR_INVALID (~(dma_addr_t)0) 23 24 #define EP0_MAX_PKT_SIZE 64 25 /* ep0 transfer state */ 26 #define WAIT_FOR_SETUP 0 27 #define DATA_STATE_XMIT 1 28 #define DATA_STATE_NEED_ZLP 2 29 #define WAIT_FOR_OUT_STATUS 3 30 #define DATA_STATE_RECV 4 31 32 #define CAPLENGTH_MASK (0xff) 33 #define DCCPARAMS_DEN_MASK (0x1f) 34 35 #define HCSPARAMS_PPC (0x10) 36 37 /* Frame Index Register Bit Masks */ 38 #define USB_FRINDEX_MASKS 0x3fff 39 40 /* Command Register Bit Masks */ 41 #define USBCMD_RUN_STOP (0x00000001) 42 #define USBCMD_CTRL_RESET (0x00000002) 43 #define USBCMD_SETUP_TRIPWIRE_SET (0x00002000) 44 #define USBCMD_SETUP_TRIPWIRE_CLEAR (~USBCMD_SETUP_TRIPWIRE_SET) 45 46 #define USBCMD_ATDTW_TRIPWIRE_SET (0x00004000) 47 #define USBCMD_ATDTW_TRIPWIRE_CLEAR (~USBCMD_ATDTW_TRIPWIRE_SET) 48 49 /* bit 15,3,2 are for frame list size */ 50 #define USBCMD_FRAME_SIZE_1024 (0x00000000) /* 000 */ 51 #define USBCMD_FRAME_SIZE_512 (0x00000004) /* 001 */ 52 #define USBCMD_FRAME_SIZE_256 (0x00000008) /* 010 */ 53 #define USBCMD_FRAME_SIZE_128 (0x0000000C) /* 011 */ 54 #define USBCMD_FRAME_SIZE_64 (0x00008000) /* 100 */ 55 #define USBCMD_FRAME_SIZE_32 (0x00008004) /* 101 */ 56 #define USBCMD_FRAME_SIZE_16 (0x00008008) /* 110 */ 57 #define USBCMD_FRAME_SIZE_8 (0x0000800C) /* 111 */ 58 59 #define EPCTRL_TX_ALL_MASK (0xFFFF0000) 60 #define EPCTRL_RX_ALL_MASK (0x0000FFFF) 61 62 #define EPCTRL_TX_DATA_TOGGLE_RST (0x00400000) 63 #define EPCTRL_TX_EP_STALL (0x00010000) 64 #define EPCTRL_RX_EP_STALL (0x00000001) 65 #define EPCTRL_RX_DATA_TOGGLE_RST (0x00000040) 66 #define EPCTRL_RX_ENABLE (0x00000080) 67 #define EPCTRL_TX_ENABLE (0x00800000) 68 #define EPCTRL_CONTROL (0x00000000) 69 #define EPCTRL_ISOCHRONOUS (0x00040000) 70 #define EPCTRL_BULK (0x00080000) 71 #define EPCTRL_INT (0x000C0000) 72 #define EPCTRL_TX_TYPE (0x000C0000) 73 #define EPCTRL_RX_TYPE (0x0000000C) 74 #define EPCTRL_DATA_TOGGLE_INHIBIT (0x00000020) 75 #define EPCTRL_TX_EP_TYPE_SHIFT (18) 76 #define EPCTRL_RX_EP_TYPE_SHIFT (2) 77 78 #define EPCOMPLETE_MAX_ENDPOINTS (16) 79 80 /* endpoint list address bit masks */ 81 #define USB_EP_LIST_ADDRESS_MASK 0xfffff800 82 83 #define PORTSCX_W1C_BITS 0x2a 84 #define PORTSCX_PORT_RESET 0x00000100 85 #define PORTSCX_PORT_POWER 0x00001000 86 #define PORTSCX_FORCE_FULL_SPEED_CONNECT 0x01000000 87 #define PORTSCX_PAR_XCVR_SELECT 0xC0000000 88 #define PORTSCX_PORT_FORCE_RESUME 0x00000040 89 #define PORTSCX_PORT_SUSPEND 0x00000080 90 #define PORTSCX_PORT_SPEED_FULL 0x00000000 91 #define PORTSCX_PORT_SPEED_LOW 0x04000000 92 #define PORTSCX_PORT_SPEED_HIGH 0x08000000 93 #define PORTSCX_PORT_SPEED_MASK 0x0C000000 94 95 /* USB MODE Register Bit Masks */ 96 #define USBMODE_CTRL_MODE_IDLE 0x00000000 97 #define USBMODE_CTRL_MODE_DEVICE 0x00000002 98 #define USBMODE_CTRL_MODE_HOST 0x00000003 99 #define USBMODE_CTRL_MODE_RSV 0x00000001 100 #define USBMODE_SETUP_LOCK_OFF 0x00000008 101 #define USBMODE_STREAM_DISABLE 0x00000010 102 103 /* USB STS Register Bit Masks */ 104 #define USBSTS_INT 0x00000001 105 #define USBSTS_ERR 0x00000002 106 #define USBSTS_PORT_CHANGE 0x00000004 107 #define USBSTS_FRM_LST_ROLL 0x00000008 108 #define USBSTS_SYS_ERR 0x00000010 109 #define USBSTS_IAA 0x00000020 110 #define USBSTS_RESET 0x00000040 111 #define USBSTS_SOF 0x00000080 112 #define USBSTS_SUSPEND 0x00000100 113 #define USBSTS_HC_HALTED 0x00001000 114 #define USBSTS_RCL 0x00002000 115 #define USBSTS_PERIODIC_SCHEDULE 0x00004000 116 #define USBSTS_ASYNC_SCHEDULE 0x00008000 117 118 119 /* Interrupt Enable Register Bit Masks */ 120 #define USBINTR_INT_EN (0x00000001) 121 #define USBINTR_ERR_INT_EN (0x00000002) 122 #define USBINTR_PORT_CHANGE_DETECT_EN (0x00000004) 123 124 #define USBINTR_ASYNC_ADV_AAE (0x00000020) 125 #define USBINTR_ASYNC_ADV_AAE_ENABLE (0x00000020) 126 #define USBINTR_ASYNC_ADV_AAE_DISABLE (0xFFFFFFDF) 127 128 #define USBINTR_RESET_EN (0x00000040) 129 #define USBINTR_SOF_UFRAME_EN (0x00000080) 130 #define USBINTR_DEVICE_SUSPEND (0x00000100) 131 132 #define USB_DEVICE_ADDRESS_MASK (0xfe000000) 133 #define USB_DEVICE_ADDRESS_BIT_SHIFT (25) 134 135 struct mv_cap_regs { 136 u32 caplength_hciversion; 137 u32 hcsparams; /* HC structural parameters */ 138 u32 hccparams; /* HC Capability Parameters*/ 139 u32 reserved[5]; 140 u32 dciversion; /* DC version number and reserved 16 bits */ 141 u32 dccparams; /* DC Capability Parameters */ 142 }; 143 144 struct mv_op_regs { 145 u32 usbcmd; /* Command register */ 146 u32 usbsts; /* Status register */ 147 u32 usbintr; /* Interrupt enable */ 148 u32 frindex; /* Frame index */ 149 u32 reserved1[1]; 150 u32 deviceaddr; /* Device Address */ 151 u32 eplistaddr; /* Endpoint List Address */ 152 u32 ttctrl; /* HOST TT status and control */ 153 u32 burstsize; /* Programmable Burst Size */ 154 u32 txfilltuning; /* Host Transmit Pre-Buffer Packet Tuning */ 155 u32 reserved[4]; 156 u32 epnak; /* Endpoint NAK */ 157 u32 epnaken; /* Endpoint NAK Enable */ 158 u32 configflag; /* Configured Flag register */ 159 u32 portsc[VUSBHS_MAX_PORTS]; /* Port Status/Control x, x = 1..8 */ 160 u32 otgsc; 161 u32 usbmode; /* USB Host/Device mode */ 162 u32 epsetupstat; /* Endpoint Setup Status */ 163 u32 epprime; /* Endpoint Initialize */ 164 u32 epflush; /* Endpoint De-initialize */ 165 u32 epstatus; /* Endpoint Status */ 166 u32 epcomplete; /* Endpoint Interrupt On Complete */ 167 u32 epctrlx[16]; /* Endpoint Control, where x = 0.. 15 */ 168 u32 mcr; /* Mux Control */ 169 u32 isr; /* Interrupt Status */ 170 u32 ier; /* Interrupt Enable */ 171 }; 172 173 struct mv_udc { 174 struct usb_gadget gadget; 175 struct usb_gadget_driver *driver; 176 spinlock_t lock; 177 struct completion *done; 178 struct platform_device *dev; 179 int irq; 180 181 struct mv_cap_regs __iomem *cap_regs; 182 struct mv_op_regs __iomem *op_regs; 183 void __iomem *phy_regs; 184 unsigned int max_eps; 185 struct mv_dqh *ep_dqh; 186 size_t ep_dqh_size; 187 dma_addr_t ep_dqh_dma; 188 189 struct dma_pool *dtd_pool; 190 struct mv_ep *eps; 191 192 struct mv_dtd *dtd_head; 193 struct mv_dtd *dtd_tail; 194 unsigned int dtd_entries; 195 196 struct mv_req *status_req; 197 struct usb_ctrlrequest local_setup_buff; 198 199 unsigned int resume_state; /* USB state to resume */ 200 unsigned int usb_state; /* USB current state */ 201 unsigned int ep0_state; /* Endpoint zero state */ 202 unsigned int ep0_dir; 203 204 unsigned int dev_addr; 205 unsigned int test_mode; 206 207 int errors; 208 unsigned softconnect:1, 209 vbus_active:1, 210 remote_wakeup:1, 211 softconnected:1, 212 force_fs:1, 213 clock_gating:1, 214 active:1, 215 stopped:1; /* stop bit is setted */ 216 217 struct work_struct vbus_work; 218 struct workqueue_struct *qwork; 219 220 struct usb_phy *transceiver; 221 222 struct mv_usb_platform_data *pdata; 223 224 /* some SOC has mutiple clock sources for USB*/ 225 unsigned int clknum; 226 struct clk *clk[0]; 227 }; 228 229 /* endpoint data structure */ 230 struct mv_ep { 231 struct usb_ep ep; 232 struct mv_udc *udc; 233 struct list_head queue; 234 struct mv_dqh *dqh; 235 const struct usb_endpoint_descriptor *desc; 236 u32 direction; 237 char name[14]; 238 unsigned stopped:1, 239 wedge:1, 240 ep_type:2, 241 ep_num:8; 242 }; 243 244 /* request data structure */ 245 struct mv_req { 246 struct usb_request req; 247 struct mv_dtd *dtd, *head, *tail; 248 struct mv_ep *ep; 249 struct list_head queue; 250 unsigned int test_mode; 251 unsigned dtd_count; 252 unsigned mapped:1; 253 }; 254 255 #define EP_QUEUE_HEAD_MULT_POS 30 256 #define EP_QUEUE_HEAD_ZLT_SEL 0x20000000 257 #define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16 258 #define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff) 259 #define EP_QUEUE_HEAD_IOS 0x00008000 260 #define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001 261 #define EP_QUEUE_HEAD_IOC 0x00008000 262 #define EP_QUEUE_HEAD_MULTO 0x00000C00 263 #define EP_QUEUE_HEAD_STATUS_HALT 0x00000040 264 #define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080 265 #define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF 266 #define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0 267 #define EP_QUEUE_FRINDEX_MASK 0x000007FF 268 #define EP_MAX_LENGTH_TRANSFER 0x4000 269 270 struct mv_dqh { 271 /* Bits 16..26 Bit 15 is Interrupt On Setup */ 272 u32 max_packet_length; 273 u32 curr_dtd_ptr; /* Current dTD Pointer */ 274 u32 next_dtd_ptr; /* Next dTD Pointer */ 275 /* Total bytes (16..30), IOC (15), INT (8), STS (0-7) */ 276 u32 size_ioc_int_sts; 277 u32 buff_ptr0; /* Buffer pointer Page 0 (12-31) */ 278 u32 buff_ptr1; /* Buffer pointer Page 1 (12-31) */ 279 u32 buff_ptr2; /* Buffer pointer Page 2 (12-31) */ 280 u32 buff_ptr3; /* Buffer pointer Page 3 (12-31) */ 281 u32 buff_ptr4; /* Buffer pointer Page 4 (12-31) */ 282 u32 reserved1; 283 /* 8 bytes of setup data that follows the Setup PID */ 284 u8 setup_buffer[8]; 285 u32 reserved2[4]; 286 }; 287 288 289 #define DTD_NEXT_TERMINATE (0x00000001) 290 #define DTD_IOC (0x00008000) 291 #define DTD_STATUS_ACTIVE (0x00000080) 292 #define DTD_STATUS_HALTED (0x00000040) 293 #define DTD_STATUS_DATA_BUFF_ERR (0x00000020) 294 #define DTD_STATUS_TRANSACTION_ERR (0x00000008) 295 #define DTD_RESERVED_FIELDS (0x00007F00) 296 #define DTD_ERROR_MASK (0x68) 297 #define DTD_ADDR_MASK (0xFFFFFFE0) 298 #define DTD_PACKET_SIZE 0x7FFF0000 299 #define DTD_LENGTH_BIT_POS (16) 300 301 struct mv_dtd { 302 u32 dtd_next; 303 u32 size_ioc_sts; 304 u32 buff_ptr0; /* Buffer pointer Page 0 */ 305 u32 buff_ptr1; /* Buffer pointer Page 1 */ 306 u32 buff_ptr2; /* Buffer pointer Page 2 */ 307 u32 buff_ptr3; /* Buffer pointer Page 3 */ 308 u32 buff_ptr4; /* Buffer pointer Page 4 */ 309 u32 scratch_ptr; 310 /* 32 bytes */ 311 dma_addr_t td_dma; /* dma address for this td */ 312 struct mv_dtd *next_dtd_virt; 313 }; 314 315 #endif 316