1 /*
2 * ispcsiphy.c
3 *
4 * TI OMAP3 ISP - CSI PHY module
5 *
6 * Copyright (C) 2010 Nokia Corporation
7 * Copyright (C) 2009 Texas Instruments, Inc.
8 *
9 * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
10 * Sakari Ailus <sakari.ailus@iki.fi>
11 *
12 * This program is free software; you can redistribute it and/or modify
13 * it under the terms of the GNU General Public License version 2 as
14 * published by the Free Software Foundation.
15 */
16
17 #include <linux/delay.h>
18 #include <linux/device.h>
19 #include <linux/regmap.h>
20 #include <linux/regulator/consumer.h>
21
22 #include "isp.h"
23 #include "ispreg.h"
24 #include "ispcsiphy.h"
25
csiphy_routing_cfg_3630(struct isp_csiphy * phy,enum isp_interface_type iface,bool ccp2_strobe)26 static void csiphy_routing_cfg_3630(struct isp_csiphy *phy,
27 enum isp_interface_type iface,
28 bool ccp2_strobe)
29 {
30 u32 reg;
31 u32 shift, mode;
32
33 regmap_read(phy->isp->syscon, phy->isp->syscon_offset, ®);
34
35 switch (iface) {
36 default:
37 /* Should not happen in practice, but let's keep the compiler happy. */
38 case ISP_INTERFACE_CCP2B_PHY1:
39 reg &= ~OMAP3630_CONTROL_CAMERA_PHY_CTRL_CSI1_RX_SEL_PHY2;
40 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY1_SHIFT;
41 break;
42 case ISP_INTERFACE_CSI2C_PHY1:
43 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY1_SHIFT;
44 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_DPHY;
45 break;
46 case ISP_INTERFACE_CCP2B_PHY2:
47 reg |= OMAP3630_CONTROL_CAMERA_PHY_CTRL_CSI1_RX_SEL_PHY2;
48 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY2_SHIFT;
49 break;
50 case ISP_INTERFACE_CSI2A_PHY2:
51 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY2_SHIFT;
52 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_DPHY;
53 break;
54 }
55
56 /* Select data/clock or data/strobe mode for CCP2 */
57 if (iface == ISP_INTERFACE_CCP2B_PHY1 ||
58 iface == ISP_INTERFACE_CCP2B_PHY2) {
59 if (ccp2_strobe)
60 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_CCP2_DATA_STROBE;
61 else
62 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_CCP2_DATA_CLOCK;
63 }
64
65 reg &= ~(OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_MASK << shift);
66 reg |= mode << shift;
67
68 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, reg);
69 }
70
csiphy_routing_cfg_3430(struct isp_csiphy * phy,u32 iface,bool on,bool ccp2_strobe)71 static void csiphy_routing_cfg_3430(struct isp_csiphy *phy, u32 iface, bool on,
72 bool ccp2_strobe)
73 {
74 u32 csirxfe = OMAP343X_CONTROL_CSIRXFE_PWRDNZ
75 | OMAP343X_CONTROL_CSIRXFE_RESET;
76
77 /* Only the CCP2B on PHY1 is configurable. */
78 if (iface != ISP_INTERFACE_CCP2B_PHY1)
79 return;
80
81 if (!on) {
82 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, 0);
83 return;
84 }
85
86 if (ccp2_strobe)
87 csirxfe |= OMAP343X_CONTROL_CSIRXFE_SELFORM;
88
89 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, csirxfe);
90 }
91
92 /*
93 * Configure OMAP 3 CSI PHY routing.
94 * @phy: relevant phy device
95 * @iface: ISP_INTERFACE_*
96 * @on: power on or off
97 * @ccp2_strobe: false: data/clock, true: data/strobe
98 *
99 * Note that the underlying routing configuration registers are part of the
100 * control (SCM) register space and part of the CORE power domain on both 3430
101 * and 3630, so they will not hold their contents in off-mode. This isn't an
102 * issue since the MPU power domain is forced on whilst the ISP is in use.
103 */
csiphy_routing_cfg(struct isp_csiphy * phy,enum isp_interface_type iface,bool on,bool ccp2_strobe)104 static void csiphy_routing_cfg(struct isp_csiphy *phy,
105 enum isp_interface_type iface, bool on,
106 bool ccp2_strobe)
107 {
108 if (phy->isp->phy_type == ISP_PHY_TYPE_3630 && on)
109 return csiphy_routing_cfg_3630(phy, iface, ccp2_strobe);
110 if (phy->isp->phy_type == ISP_PHY_TYPE_3430)
111 return csiphy_routing_cfg_3430(phy, iface, on, ccp2_strobe);
112 }
113
114 /*
115 * csiphy_power_autoswitch_enable
116 * @enable: Sets or clears the autoswitch function enable flag.
117 */
csiphy_power_autoswitch_enable(struct isp_csiphy * phy,bool enable)118 static void csiphy_power_autoswitch_enable(struct isp_csiphy *phy, bool enable)
119 {
120 isp_reg_clr_set(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG,
121 ISPCSI2_PHY_CFG_PWR_AUTO,
122 enable ? ISPCSI2_PHY_CFG_PWR_AUTO : 0);
123 }
124
125 /*
126 * csiphy_set_power
127 * @power: Power state to be set.
128 *
129 * Returns 0 if successful, or -EBUSY if the retry count is exceeded.
130 */
csiphy_set_power(struct isp_csiphy * phy,u32 power)131 static int csiphy_set_power(struct isp_csiphy *phy, u32 power)
132 {
133 u32 reg;
134 u8 retry_count;
135
136 isp_reg_clr_set(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG,
137 ISPCSI2_PHY_CFG_PWR_CMD_MASK, power);
138
139 retry_count = 0;
140 do {
141 udelay(50);
142 reg = isp_reg_readl(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG) &
143 ISPCSI2_PHY_CFG_PWR_STATUS_MASK;
144
145 if (reg != power >> 2)
146 retry_count++;
147
148 } while ((reg != power >> 2) && (retry_count < 100));
149
150 if (retry_count == 100) {
151 dev_err(phy->isp->dev, "CSI2 CIO set power failed!\n");
152 return -EBUSY;
153 }
154
155 return 0;
156 }
157
158 /*
159 * TCLK values are OK at their reset values
160 */
161 #define TCLK_TERM 0
162 #define TCLK_MISS 1
163 #define TCLK_SETTLE 14
164
omap3isp_csiphy_config(struct isp_csiphy * phy)165 static int omap3isp_csiphy_config(struct isp_csiphy *phy)
166 {
167 struct isp_pipeline *pipe = to_isp_pipeline(phy->entity);
168 struct isp_bus_cfg *buscfg = v4l2_subdev_to_bus_cfg(pipe->external);
169 struct isp_csiphy_lanes_cfg *lanes;
170 int csi2_ddrclk_khz;
171 unsigned int num_data_lanes, used_lanes = 0;
172 unsigned int i;
173 u32 reg;
174
175 if (buscfg->interface == ISP_INTERFACE_CCP2B_PHY1
176 || buscfg->interface == ISP_INTERFACE_CCP2B_PHY2) {
177 lanes = &buscfg->bus.ccp2.lanecfg;
178 num_data_lanes = 1;
179 } else {
180 lanes = &buscfg->bus.csi2.lanecfg;
181 num_data_lanes = buscfg->bus.csi2.num_data_lanes;
182 }
183
184 if (num_data_lanes > phy->num_data_lanes)
185 return -EINVAL;
186
187 /* Clock and data lanes verification */
188 for (i = 0; i < num_data_lanes; i++) {
189 if (lanes->data[i].pol > 1 || lanes->data[i].pos > 3)
190 return -EINVAL;
191
192 if (used_lanes & (1 << lanes->data[i].pos))
193 return -EINVAL;
194
195 used_lanes |= 1 << lanes->data[i].pos;
196 }
197
198 if (lanes->clk.pol > 1 || lanes->clk.pos > 3)
199 return -EINVAL;
200
201 if (lanes->clk.pos == 0 || used_lanes & (1 << lanes->clk.pos))
202 return -EINVAL;
203
204 /*
205 * The PHY configuration is lost in off mode, that's not an
206 * issue since the MPU power domain is forced on whilst the
207 * ISP is in use.
208 */
209 csiphy_routing_cfg(phy, buscfg->interface, true,
210 buscfg->bus.ccp2.phy_layer);
211
212 /* DPHY timing configuration */
213 /* CSI-2 is DDR and we only count used lanes. */
214 csi2_ddrclk_khz = pipe->external_rate / 1000
215 / (2 * hweight32(used_lanes)) * pipe->external_width;
216
217 reg = isp_reg_readl(phy->isp, phy->phy_regs, ISPCSIPHY_REG0);
218
219 reg &= ~(ISPCSIPHY_REG0_THS_TERM_MASK |
220 ISPCSIPHY_REG0_THS_SETTLE_MASK);
221 /* THS_TERM: Programmed value = ceil(12.5 ns/DDRClk period) - 1. */
222 reg |= (DIV_ROUND_UP(25 * csi2_ddrclk_khz, 2000000) - 1)
223 << ISPCSIPHY_REG0_THS_TERM_SHIFT;
224 /* THS_SETTLE: Programmed value = ceil(90 ns/DDRClk period) + 3. */
225 reg |= (DIV_ROUND_UP(90 * csi2_ddrclk_khz, 1000000) + 3)
226 << ISPCSIPHY_REG0_THS_SETTLE_SHIFT;
227
228 isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG0);
229
230 reg = isp_reg_readl(phy->isp, phy->phy_regs, ISPCSIPHY_REG1);
231
232 reg &= ~(ISPCSIPHY_REG1_TCLK_TERM_MASK |
233 ISPCSIPHY_REG1_TCLK_MISS_MASK |
234 ISPCSIPHY_REG1_TCLK_SETTLE_MASK);
235 reg |= TCLK_TERM << ISPCSIPHY_REG1_TCLK_TERM_SHIFT;
236 reg |= TCLK_MISS << ISPCSIPHY_REG1_TCLK_MISS_SHIFT;
237 reg |= TCLK_SETTLE << ISPCSIPHY_REG1_TCLK_SETTLE_SHIFT;
238
239 isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG1);
240
241 /* DPHY lane configuration */
242 reg = isp_reg_readl(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG);
243
244 for (i = 0; i < num_data_lanes; i++) {
245 reg &= ~(ISPCSI2_PHY_CFG_DATA_POL_MASK(i + 1) |
246 ISPCSI2_PHY_CFG_DATA_POSITION_MASK(i + 1));
247 reg |= (lanes->data[i].pol <<
248 ISPCSI2_PHY_CFG_DATA_POL_SHIFT(i + 1));
249 reg |= (lanes->data[i].pos <<
250 ISPCSI2_PHY_CFG_DATA_POSITION_SHIFT(i + 1));
251 }
252
253 reg &= ~(ISPCSI2_PHY_CFG_CLOCK_POL_MASK |
254 ISPCSI2_PHY_CFG_CLOCK_POSITION_MASK);
255 reg |= lanes->clk.pol << ISPCSI2_PHY_CFG_CLOCK_POL_SHIFT;
256 reg |= lanes->clk.pos << ISPCSI2_PHY_CFG_CLOCK_POSITION_SHIFT;
257
258 isp_reg_writel(phy->isp, reg, phy->cfg_regs, ISPCSI2_PHY_CFG);
259
260 return 0;
261 }
262
omap3isp_csiphy_acquire(struct isp_csiphy * phy,struct media_entity * entity)263 int omap3isp_csiphy_acquire(struct isp_csiphy *phy, struct media_entity *entity)
264 {
265 int rval;
266
267 if (phy->vdd == NULL) {
268 dev_err(phy->isp->dev,
269 "Power regulator for CSI PHY not available\n");
270 return -ENODEV;
271 }
272
273 mutex_lock(&phy->mutex);
274
275 rval = regulator_enable(phy->vdd);
276 if (rval < 0)
277 goto done;
278
279 rval = omap3isp_csi2_reset(phy->csi2);
280 if (rval < 0)
281 goto done;
282
283 phy->entity = entity;
284
285 rval = omap3isp_csiphy_config(phy);
286 if (rval < 0)
287 goto done;
288
289 if (phy->isp->revision == ISP_REVISION_15_0) {
290 rval = csiphy_set_power(phy, ISPCSI2_PHY_CFG_PWR_CMD_ON);
291 if (rval) {
292 regulator_disable(phy->vdd);
293 goto done;
294 }
295
296 csiphy_power_autoswitch_enable(phy, true);
297 }
298 done:
299 if (rval < 0)
300 phy->entity = NULL;
301
302 mutex_unlock(&phy->mutex);
303 return rval;
304 }
305
omap3isp_csiphy_release(struct isp_csiphy * phy)306 void omap3isp_csiphy_release(struct isp_csiphy *phy)
307 {
308 mutex_lock(&phy->mutex);
309 if (phy->entity) {
310 struct isp_pipeline *pipe = to_isp_pipeline(phy->entity);
311 struct isp_bus_cfg *buscfg =
312 v4l2_subdev_to_bus_cfg(pipe->external);
313
314 csiphy_routing_cfg(phy, buscfg->interface, false,
315 buscfg->bus.ccp2.phy_layer);
316 if (phy->isp->revision == ISP_REVISION_15_0) {
317 csiphy_power_autoswitch_enable(phy, false);
318 csiphy_set_power(phy, ISPCSI2_PHY_CFG_PWR_CMD_OFF);
319 }
320 regulator_disable(phy->vdd);
321 phy->entity = NULL;
322 }
323 mutex_unlock(&phy->mutex);
324 }
325
326 /*
327 * omap3isp_csiphy_init - Initialize the CSI PHY frontends
328 */
omap3isp_csiphy_init(struct isp_device * isp)329 int omap3isp_csiphy_init(struct isp_device *isp)
330 {
331 struct isp_csiphy *phy1 = &isp->isp_csiphy1;
332 struct isp_csiphy *phy2 = &isp->isp_csiphy2;
333
334 phy2->isp = isp;
335 phy2->csi2 = &isp->isp_csi2a;
336 phy2->num_data_lanes = ISP_CSIPHY2_NUM_DATA_LANES;
337 phy2->cfg_regs = OMAP3_ISP_IOMEM_CSI2A_REGS1;
338 phy2->phy_regs = OMAP3_ISP_IOMEM_CSIPHY2;
339 mutex_init(&phy2->mutex);
340
341 phy1->isp = isp;
342 mutex_init(&phy1->mutex);
343
344 if (isp->revision == ISP_REVISION_15_0) {
345 phy1->csi2 = &isp->isp_csi2c;
346 phy1->num_data_lanes = ISP_CSIPHY1_NUM_DATA_LANES;
347 phy1->cfg_regs = OMAP3_ISP_IOMEM_CSI2C_REGS1;
348 phy1->phy_regs = OMAP3_ISP_IOMEM_CSIPHY1;
349 }
350
351 return 0;
352 }
353
omap3isp_csiphy_cleanup(struct isp_device * isp)354 void omap3isp_csiphy_cleanup(struct isp_device *isp)
355 {
356 mutex_destroy(&isp->isp_csiphy1.mutex);
357 mutex_destroy(&isp->isp_csiphy2.mutex);
358 }
359