| /arch/arm/mach-shmobile/ |
| D | Kconfig | 78 select I2C
83 select I2C
88 select I2C
|
| /arch/arm/mach-davinci/ |
| D | Kconfig | 71 select I2C
80 select I2C
112 select I2C
126 select I2C
137 select I2C
146 detected automatically based on successful probe of the I2C
175 EVM is detected automatically based on successful probe of the I2C
207 select I2C
|
| /arch/avr32/boards/atngw100/ |
| D | Kconfig_mrmt | 62 bool "Use External RTC on I2C Bus"
64 RMT1 has an optional RTC device on the I2C bus.
|
| /arch/arm/plat-samsung/ |
| D | Kconfig | 108 Compile in platform device definitions for I2C channel 1
113 Compile in platform device definitions for I2C channel 2
118 Compile in platform device definition for I2C controller 3
123 Compile in platform device definition for I2C controller 4
128 Compile in platform device definition for I2C controller 5
133 Compile in platform device definition for I2C controller 6
138 Compile in platform device definition for I2C controller 7
|
| /arch/cris/arch-v10/drivers/ |
| D | Kconfig | 432 bool "I2C support"
435 Enables an I2C driver on ETRAX100.
442 # this is true for most products since PB-I2C seems to be somewhat
445 bool "I2C uses PB not PB-I2C"
448 Select whether to use the special I2C mode in the PB I/O register or
450 that access the I2C I/O pins directly instead of going through the
451 I2C driver, like the DS1302 realtime-clock driver. If you are
455 int "I2C SDA bit number"
462 int "I2C SCL bit number"
469 bool "I2C EEPROM (non-volatile RAM) support"
[all …]
|
| /arch/arm/mach-nomadik/ |
| D | Kconfig | 22 select I2C
|
| /arch/arm/mach-s5pv210/ |
| D | Kconfig | 17 select HAVE_S3C2410_I2C if I2C
|
| /arch/arm/boot/dts/ |
| D | dove-sbc-a510.dts | 46 * SBC-A510 comprises a PCA9555 I2C GPIO expander its GPIO lines connected to
104 * USB port 0 can be powered and monitored by I2C GPIO expander:
116 * I2C bus layout:
170 * SDIO0 is connected to a MMC/SD/SDIO socket, I2C GPIO expander has
|
| D | imx6q-gk802.dts | 57 /* Internal I2C */
71 /* External I2C via HDMI */
|
| D | kirkwood-nas2big.dts | 57 * An I2C fan controller (GMT G762) is used but alarm is
104 * An external I2C RTC (Dallas DS1337S+) is used. This allows
|
| D | stih41x-b2020.dtsi | 48 /* HDMI Tx I2C */
|
| D | stih41x-b2000.dtsi | 43 /* HDMI Tx I2C */
|
| D | tegra30-colibri.dtsi | 162 /* Power I2C (On-module) */
175 * THERMD_ALERT#, unlatched I2C address pin of LM95245
203 * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
|
| /arch/sh/kernel/cpu/sh4a/ |
| D | setup-sh7366.c | 275 DMAC0123, VIOVOU, MMC, DMAC45, FLCTL, I2C, enumerator
316 INTC_GROUP(I2C, I2C_ALI, I2C_TACKI, I2C_WAITI, I2C_DTEI),
357 { 0xa408001c, 0, 16, 4, /* IPRH */ { MSIOF, 0, FLCTL, I2C } },
|
| D | setup-sh7770.c | 351 HAC, IPI, SPDIF, HUDI, I2C, enumerator
379 INTC_VECT(HUDI, 0x600), INTC_VECT(I2C, 0x620),
437 DMAC, I2C, HUDI, SPDIF, IPI, HAC, TMU, GPIO } },
442 { 0xffe00004, 0, 32, 8, /* INT2PRI1 */ { IPI, SPDIF, HUDI, I2C } },
|
| D | setup-sh7723.c | 483 DMAC1A, DMAC0A, VIO, DMAC0B, FLCTL, I2C, _2DG, enumerator
583 INTC_GROUP(I2C,I2C_ALI,I2C_TACKI,I2C_WAITI,I2C_DTEI),
631 { 0xa408001c, 0, 16, 4, /* IPRH */ { MSIOF_MSIOFI0,MSIOF_MSIOFI1, FLCTL, I2C } },
|
| D | setup-sh7722.c | 549 SIM, RTC, DMAC0123, VIOVOU, USB, DMAC45, FLCTL, I2C, SDHI, enumerator
594 INTC_GROUP(I2C, I2C_ALI, I2C_TACKI, I2C_WAITI, I2C_DTEI),
635 { 0xa408001c, 0, 16, 4, /* IPRH */ { SIOF0, SIOF1, FLCTL, I2C } },
|
| /arch/arm/mach-ux500/ |
| D | Kconfig | 39 select I2C
|
| /arch/arm/mach-s3c64xx/ |
| D | Kconfig | 198 depends on I2C=y
213 depends on I2C=y
280 depends on I2C=y
|
| /arch/unicore32/ |
| D | Kconfig | 222 tristate "I2C Battery BQ27200 Support"
228 tristate "I2C EEPROMs AT24 support"
|
| /arch/powerpc/platforms/8xx/ |
| D | Kconfig | 162 bool "I2C/SPI relocation patch"
167 bool "I2C/SPI/SMC1 relocation patch"
|
| /arch/powerpc/boot/dts/fsl/ |
| D | pq3-i2c-1.dtsi | 2 * PQ3 I2C device tree stub [ controller @ offset 0x3100 ]
|
| D | pq3-i2c-0.dtsi | 2 * PQ3 I2C device tree stub [ controller @ offset 0x3000 ]
|
| D | qoriq-i2c-0.dtsi | 2 * QorIQ I2C device tree stub [ controller @ offset 0x118000 ]
|
| D | qoriq-i2c-1.dtsi | 2 * QorIQ I2C device tree stub [ controller @ offset 0x119000 ]
|