1/* 2 * Support for CompuLab CM-T3517 3 */ 4/dts-v1/; 5 6#include "am3517.dtsi" 7#include "omap3-cm-t3x.dtsi" 8 9/ { 10 model = "CompuLab CM-T3517"; 11 compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3"; 12 13 vmmc: regulator-vmmc { 14 compatible = "regulator-fixed"; 15 regulator-name = "vmmc"; 16 regulator-min-microvolt = <3300000>; 17 regulator-max-microvolt = <3300000>; 18 }; 19 20 wl12xx_vmmc2: wl12xx_vmmc2 { 21 compatible = "regulator-fixed"; 22 regulator-name = "vw1271"; 23 pinctrl-names = "default"; 24 pinctrl-0 = < 25 &wl12xx_wkup_pins 26 &wl12xx_core_pins 27 >; 28 regulator-min-microvolt = <1800000>; 29 regulator-max-microvolt = <1800000>; 30 gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */ 31 startup-delay-us = <20000>; 32 enable-active-high; 33 }; 34 35 wl12xx_vaux2: wl12xx_vaux2 { 36 compatible = "regulator-fixed"; 37 regulator-name = "vwl1271_vaux2"; 38 regulator-min-microvolt = <1800000>; 39 regulator-max-microvolt = <1800000>; 40 }; 41}; 42 43&omap3_pmx_wkup { 44 45 wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins { 46 pinctrl-single,pins = < 47 OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ 48 OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4) /* sys_boot4.gpio_6 */ 49 >; 50 }; 51}; 52 53&omap3_pmx_core { 54 55 phy1_reset_pins: pinmux_hsusb1_phy_reset_pins { 56 pinctrl-single,pins = < 57 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4) /* uart2_tx.gpio_146 */ 58 >; 59 }; 60 61 phy2_reset_pins: pinmux_hsusb2_phy_reset_pins { 62 pinctrl-single,pins = < 63 OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4) /* uart2_rx.gpio_147 */ 64 >; 65 }; 66 67 otg_drv_vbus: pinmux_otg_drv_vbus { 68 pinctrl-single,pins = < 69 OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50MHz_clk.usb0_drvvbus */ 70 >; 71 }; 72 73 mmc2_pins: pinmux_mmc2_pins { 74 pinctrl-single,pins = < 75 OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ 76 OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ 77 OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ 78 OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ 79 OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ 80 OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ 81 >; 82 }; 83 84 wl12xx_core_pins: pinmux_wl12xx_core_pins { 85 pinctrl-single,pins = < 86 OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */ 87 OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_rts.gpio_145 */ 88 >; 89 }; 90 91 usb_hub_pins: pinmux_usb_hub_pins { 92 pinctrl-single,pins = < 93 OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_clkx.gpio_152 - USB HUB RST */ 94 >; 95 }; 96}; 97 98&hsusb1_phy { 99 pinctrl-names = "default"; 100 pinctrl-0 = <&phy1_reset_pins>; 101 reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>; 102}; 103 104&hsusb2_phy { 105 pinctrl-names = "default"; 106 pinctrl-0 = <&phy2_reset_pins>; 107 reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; 108}; 109 110&davinci_emac { 111 status = "okay"; 112}; 113 114&davinci_mdio { 115 status = "okay"; 116}; 117 118&am35x_otg_hs { 119 status = "okay"; 120 pinctrl-names = "default"; 121 pinctrl-0 = <&otg_drv_vbus>; 122}; 123 124&mmc1 { 125 vmmc-supply = <&vmmc>; 126}; 127 128&mmc2 { 129 pinctrl-names = "default"; 130 pinctrl-0 = <&mmc2_pins>; 131 vmmc-supply = <&wl12xx_vmmc2>; 132 vmmc_aux-supply = <&wl12xx_vaux2>; 133 non-removable; 134 bus-width = <4>; 135 cap-power-off-card; 136 137 #address-cells = <1>; 138 #size-cells = <0>; 139 wlcore: wlcore@2 { 140 compatible = "ti,wl1271"; 141 reg = <2>; 142 interrupt-parent = <&gpio5>; 143 interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; /* gpio 145 */ 144 ref-clock-frequency = <38400000>; 145 }; 146}; 147 148&dss { 149 status = "ok"; 150 151 pinctrl-names = "default"; 152 pinctrl-0 = < 153 &dss_dpi_pins_common 154 &dss_dpi_pins_cm_t35x 155 >; 156}; 157 158