1/* 2 * Support for CompuLab CM-T3530 3 */ 4/dts-v1/; 5 6#include "omap34xx.dtsi" 7#include "omap3-cm-t3x30.dtsi" 8 9/ { 10 model = "CompuLab CM-T3530"; 11 compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3"; 12 13 /* Regulator to trigger the reset signal of the Wifi module */ 14 mmc2_sdio_reset: regulator-mmc2-sdio-reset { 15 compatible = "regulator-fixed"; 16 regulator-name = "regulator-mmc2-sdio-reset"; 17 regulator-min-microvolt = <3300000>; 18 regulator-max-microvolt = <3300000>; 19 gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>; 20 enable-active-high; 21 }; 22}; 23 24&omap3_pmx_core { 25 mmc2_pins: pinmux_mmc2_pins { 26 pinctrl-single,pins = < 27 OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ 28 OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ 29 OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ 30 OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ 31 OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ 32 OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ 33 OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */ 34 OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */ 35 OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */ 36 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ 37 >; 38 }; 39}; 40 41&mmc2 { 42 pinctrl-names = "default"; 43 pinctrl-0 = <&mmc2_pins>; 44 vmmc-supply = <&mmc2_sdio_reset>; 45 non-removable; 46 bus-width = <4>; 47 cap-power-off-card; 48}; 49 50&dss { 51 status = "ok"; 52 53 pinctrl-names = "default"; 54 pinctrl-0 = < 55 &dss_dpi_pins_common 56 &dss_dpi_pins_cm_t35x 57 >; 58}; 59 60