1/* 2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ 3 * 4 * This program is free software; you can redistribute it and/or modify 5 * it under the terms of the GNU General Public License version 2 as 6 * published by the Free Software Foundation. 7 */ 8#include "omap5.dtsi" 9#include <dt-bindings/interrupt-controller/irq.h> 10#include <dt-bindings/interrupt-controller/arm-gic.h> 11 12/ { 13 aliases { 14 display0 = &hdmi0; 15 }; 16 17 vmmcsd_fixed: fixedregulator-mmcsd { 18 compatible = "regulator-fixed"; 19 regulator-name = "vmmcsd_fixed"; 20 regulator-min-microvolt = <3000000>; 21 regulator-max-microvolt = <3000000>; 22 }; 23 24 mmc3_pwrseq: sdhci0_pwrseq { 25 compatible = "mmc-pwrseq-simple"; 26 clocks = <&clk32kgaudio>; 27 clock-names = "ext_clock"; 28 }; 29 30 vmmcsdio_fixed: fixedregulator-mmcsdio { 31 compatible = "regulator-fixed"; 32 regulator-name = "vmmcsdio_fixed"; 33 regulator-min-microvolt = <1800000>; 34 regulator-max-microvolt = <1800000>; 35 gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */ 36 enable-active-high; 37 startup-delay-us = <70000>; 38 pinctrl-names = "default"; 39 pinctrl-0 = <&wlan_pins>; 40 }; 41 42 /* HS USB Host PHY on PORT 2 */ 43 hsusb2_phy: hsusb2_phy { 44 compatible = "usb-nop-xceiv"; 45 reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ 46 clocks = <&auxclk1_ck>; 47 clock-names = "main_clk"; 48 clock-frequency = <19200000>; 49 }; 50 51 /* HS USB Host PHY on PORT 3 */ 52 hsusb3_phy: hsusb3_phy { 53 compatible = "usb-nop-xceiv"; 54 reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ 55 }; 56 57 leds { 58 compatible = "gpio-leds"; 59 led@1 { 60 label = "omap5:blue:usr1"; 61 gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */ 62 linux,default-trigger = "heartbeat"; 63 default-state = "off"; 64 }; 65 }; 66 67 tpd12s015: encoder@0 { 68 compatible = "ti,tpd12s015"; 69 70 pinctrl-names = "default"; 71 pinctrl-0 = <&tpd12s015_pins>; 72 73 /* gpios defined in the board specific dts */ 74 75 ports { 76 #address-cells = <1>; 77 #size-cells = <0>; 78 79 port@0 { 80 reg = <0>; 81 82 tpd12s015_in: endpoint@0 { 83 remote-endpoint = <&hdmi_out>; 84 }; 85 }; 86 87 port@1 { 88 reg = <1>; 89 90 tpd12s015_out: endpoint@0 { 91 remote-endpoint = <&hdmi_connector_in>; 92 }; 93 }; 94 }; 95 }; 96 97 hdmi0: connector@0 { 98 compatible = "hdmi-connector"; 99 label = "hdmi"; 100 101 type = "b"; 102 103 port { 104 hdmi_connector_in: endpoint { 105 remote-endpoint = <&tpd12s015_out>; 106 }; 107 }; 108 }; 109 110 sound: sound { 111 compatible = "ti,abe-twl6040"; 112 ti,model = "omap5-uevm"; 113 114 ti,mclk-freq = <19200000>; 115 116 ti,mcpdm = <&mcpdm>; 117 118 ti,twl6040 = <&twl6040>; 119 120 /* Audio routing */ 121 ti,audio-routing = 122 "Headset Stereophone", "HSOL", 123 "Headset Stereophone", "HSOR", 124 "Line Out", "AUXL", 125 "Line Out", "AUXR", 126 "HSMIC", "Headset Mic", 127 "Headset Mic", "Headset Mic Bias", 128 "AFML", "Line In", 129 "AFMR", "Line In"; 130 }; 131}; 132 133&gpio8 { 134 /* TI trees use GPIO instead of msecure, see also muxing */ 135 p234 { 136 gpio-hog; 137 gpios = <10 GPIO_ACTIVE_HIGH>; 138 output-high; 139 line-name = "gpio8_234/msecure"; 140 }; 141}; 142 143&omap5_pmx_core { 144 pinctrl-names = "default"; 145 pinctrl-0 = < 146 &usbhost_pins 147 &led_gpio_pins 148 >; 149 150 twl6040_pins: pinmux_twl6040_pins { 151 pinctrl-single,pins = < 152 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ 153 >; 154 }; 155 156 mcpdm_pins: pinmux_mcpdm_pins { 157 pinctrl-single,pins = < 158 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ 159 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ 160 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ 161 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ 162 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ 163 >; 164 }; 165 166 mcbsp1_pins: pinmux_mcbsp1_pins { 167 pinctrl-single,pins = < 168 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ 169 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ 170 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ 171 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ 172 >; 173 }; 174 175 mcbsp2_pins: pinmux_mcbsp2_pins { 176 pinctrl-single,pins = < 177 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ 178 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ 179 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ 180 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ 181 >; 182 }; 183 184 i2c1_pins: pinmux_i2c1_pins { 185 pinctrl-single,pins = < 186 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ 187 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ 188 >; 189 }; 190 191 mcspi2_pins: pinmux_mcspi2_pins { 192 pinctrl-single,pins = < 193 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ 194 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ 195 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ 196 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ 197 >; 198 }; 199 200 mcspi3_pins: pinmux_mcspi3_pins { 201 pinctrl-single,pins = < 202 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ 203 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ 204 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ 205 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ 206 >; 207 }; 208 209 mmc3_pins: pinmux_mmc3_pins { 210 pinctrl-single,pins = < 211 OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ 212 OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ 213 OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ 214 OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ 215 OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ 216 OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ 217 >; 218 }; 219 220 wlan_pins: pinmux_wlan_pins { 221 pinctrl-single,pins = < 222 OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */ 223 >; 224 }; 225 226 /* TI trees use GPIO mode; msecure mode does not work reliably? */ 227 palmas_msecure_pins: palmas_msecure_pins { 228 pinctrl-single,pins = < 229 OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */ 230 >; 231 }; 232 233 usbhost_pins: pinmux_usbhost_pins { 234 pinctrl-single,pins = < 235 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ 236 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ 237 238 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ 239 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ 240 241 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ 242 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ 243 >; 244 }; 245 246 led_gpio_pins: pinmux_led_gpio_pins { 247 pinctrl-single,pins = < 248 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ 249 >; 250 }; 251 252 uart1_pins: pinmux_uart1_pins { 253 pinctrl-single,pins = < 254 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ 255 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ 256 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ 257 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ 258 >; 259 }; 260 261 uart3_pins: pinmux_uart3_pins { 262 pinctrl-single,pins = < 263 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ 264 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ 265 >; 266 }; 267 268 uart5_pins: pinmux_uart5_pins { 269 pinctrl-single,pins = < 270 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ 271 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ 272 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ 273 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ 274 >; 275 }; 276 277 dss_hdmi_pins: pinmux_dss_hdmi_pins { 278 pinctrl-single,pins = < 279 0x0fc (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ 280 0x100 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ 281 0x102 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ 282 >; 283 }; 284 285 tpd12s015_pins: pinmux_tpd12s015_pins { 286 pinctrl-single,pins = < 287 0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ 288 >; 289 }; 290}; 291 292&omap5_pmx_wkup { 293 pinctrl-names = "default"; 294 pinctrl-0 = < 295 &usbhost_wkup_pins 296 >; 297 298 palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins { 299 pinctrl-single,pins = < 300 OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */ 301 >; 302 }; 303 304 usbhost_wkup_pins: pinmux_usbhost_wkup_pins { 305 pinctrl-single,pins = < 306 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ 307 >; 308 }; 309 310 wlcore_irq_pin: pinmux_wlcore_irq_pin { 311 pinctrl-single,pins = < 312 OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ 313 >; 314 }; 315}; 316 317&mmc1 { 318 vmmc-supply = <&ldo9_reg>; 319 bus-width = <4>; 320}; 321 322&mmc2 { 323 vmmc-supply = <&vmmcsd_fixed>; 324 bus-width = <8>; 325 ti,non-removable; 326}; 327 328&mmc3 { 329 vmmc-supply = <&vmmcsdio_fixed>; 330 mmc-pwrseq = <&mmc3_pwrseq>; 331 bus-width = <4>; 332 non-removable; 333 cap-power-off-card; 334 pinctrl-names = "default"; 335 pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>; 336 interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH 337 &omap5_pmx_core 0x168>; 338 339 #address-cells = <1>; 340 #size-cells = <0>; 341 wlcore: wlcore@2 { 342 compatible = "ti,wl1271"; 343 reg = <2>; 344 interrupt-parent = <&gpio1>; 345 interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */ 346 ref-clock-frequency = <26000000>; 347 }; 348}; 349 350&mmc4 { 351 status = "disabled"; 352}; 353 354&mmc5 { 355 status = "disabled"; 356}; 357 358&i2c1 { 359 pinctrl-names = "default"; 360 pinctrl-0 = <&i2c1_pins>; 361 362 clock-frequency = <400000>; 363 364 palmas: palmas@48 { 365 compatible = "ti,palmas"; 366 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ 367 reg = <0x48>; 368 interrupt-controller; 369 #interrupt-cells = <2>; 370 ti,system-power-controller; 371 pinctrl-names = "default"; 372 pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>; 373 374 extcon_usb3: palmas_usb { 375 compatible = "ti,palmas-usb-vid"; 376 ti,enable-vbus-detection; 377 ti,enable-id-detection; 378 ti,wakeup; 379 }; 380 381 clk32kgaudio: palmas_clk32k@1 { 382 compatible = "ti,palmas-clk32kgaudio"; 383 #clock-cells = <0>; 384 }; 385 386 rtc { 387 compatible = "ti,palmas-rtc"; 388 interrupt-parent = <&palmas>; 389 interrupts = <8 IRQ_TYPE_NONE>; 390 ti,backup-battery-chargeable; 391 ti,backup-battery-charge-high-current; 392 }; 393 394 palmas_pmic { 395 compatible = "ti,palmas-pmic"; 396 interrupt-parent = <&palmas>; 397 interrupts = <14 IRQ_TYPE_NONE>; 398 interrupt-name = "short-irq"; 399 400 ti,ldo6-vibrator; 401 402 regulators { 403 smps123_reg: smps123 { 404 /* VDD_OPP_MPU */ 405 regulator-name = "smps123"; 406 regulator-min-microvolt = < 600000>; 407 regulator-max-microvolt = <1500000>; 408 regulator-always-on; 409 regulator-boot-on; 410 }; 411 412 smps45_reg: smps45 { 413 /* VDD_OPP_MM */ 414 regulator-name = "smps45"; 415 regulator-min-microvolt = < 600000>; 416 regulator-max-microvolt = <1310000>; 417 regulator-always-on; 418 regulator-boot-on; 419 }; 420 421 smps6_reg: smps6 { 422 /* VDD_DDR3 - over VDD_SMPS6 */ 423 regulator-name = "smps6"; 424 regulator-min-microvolt = <1200000>; 425 regulator-max-microvolt = <1200000>; 426 regulator-always-on; 427 regulator-boot-on; 428 }; 429 430 smps7_reg: smps7 { 431 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ 432 regulator-name = "smps7"; 433 regulator-min-microvolt = <1800000>; 434 regulator-max-microvolt = <1800000>; 435 regulator-always-on; 436 regulator-boot-on; 437 }; 438 439 smps8_reg: smps8 { 440 /* VDD_OPP_CORE */ 441 regulator-name = "smps8"; 442 regulator-min-microvolt = < 600000>; 443 regulator-max-microvolt = <1310000>; 444 regulator-always-on; 445 regulator-boot-on; 446 }; 447 448 smps9_reg: smps9 { 449 /* VDDA_2v1_AUD over VDD_2v1 */ 450 regulator-name = "smps9"; 451 regulator-min-microvolt = <2100000>; 452 regulator-max-microvolt = <2100000>; 453 ti,smps-range = <0x80>; 454 }; 455 456 smps10_out2_reg: smps10_out2 { 457 /* VBUS_5V_OTG */ 458 regulator-name = "smps10_out2"; 459 regulator-min-microvolt = <5000000>; 460 regulator-max-microvolt = <5000000>; 461 regulator-always-on; 462 regulator-boot-on; 463 }; 464 465 smps10_out1_reg: smps10_out1 { 466 /* VBUS_5V_OTG */ 467 regulator-name = "smps10_out1"; 468 regulator-min-microvolt = <5000000>; 469 regulator-max-microvolt = <5000000>; 470 }; 471 472 ldo1_reg: ldo1 { 473 /* VDDAPHY_CAM: vdda_csiport */ 474 regulator-name = "ldo1"; 475 regulator-min-microvolt = <1500000>; 476 regulator-max-microvolt = <1800000>; 477 }; 478 479 ldo2_reg: ldo2 { 480 /* VCC_2V8_DISP: Does not go anywhere */ 481 regulator-name = "ldo2"; 482 regulator-min-microvolt = <2800000>; 483 regulator-max-microvolt = <2800000>; 484 /* Unused */ 485 status = "disabled"; 486 }; 487 488 ldo3_reg: ldo3 { 489 /* VDDAPHY_MDM: vdda_lli */ 490 regulator-name = "ldo3"; 491 regulator-min-microvolt = <1500000>; 492 regulator-max-microvolt = <1500000>; 493 regulator-boot-on; 494 /* Only if Modem is used */ 495 status = "disabled"; 496 }; 497 498 ldo4_reg: ldo4 { 499 /* VDDAPHY_DISP: vdda_dsiport/hdmi */ 500 regulator-name = "ldo4"; 501 regulator-min-microvolt = <1500000>; 502 regulator-max-microvolt = <1800000>; 503 }; 504 505 ldo5_reg: ldo5 { 506 /* VDDA_1V8_PHY: usb/sata/hdmi.. */ 507 regulator-name = "ldo5"; 508 regulator-min-microvolt = <1800000>; 509 regulator-max-microvolt = <1800000>; 510 regulator-always-on; 511 regulator-boot-on; 512 }; 513 514 ldo6_reg: ldo6 { 515 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ 516 regulator-name = "ldo6"; 517 regulator-min-microvolt = <1200000>; 518 regulator-max-microvolt = <1200000>; 519 regulator-always-on; 520 regulator-boot-on; 521 }; 522 523 ldo7_reg: ldo7 { 524 /* VDD_VPP: vpp1 */ 525 regulator-name = "ldo7"; 526 regulator-min-microvolt = <2000000>; 527 regulator-max-microvolt = <2000000>; 528 /* Only for efuse reprograming! */ 529 status = "disabled"; 530 }; 531 532 ldo8_reg: ldo8 { 533 /* VDD_3v0: Does not go anywhere */ 534 regulator-name = "ldo8"; 535 regulator-min-microvolt = <3000000>; 536 regulator-max-microvolt = <3000000>; 537 regulator-boot-on; 538 /* Unused */ 539 status = "disabled"; 540 }; 541 542 ldo9_reg: ldo9 { 543 /* VCC_DV_SDIO: vdds_sdcard */ 544 regulator-name = "ldo9"; 545 regulator-min-microvolt = <1800000>; 546 regulator-max-microvolt = <3000000>; 547 regulator-boot-on; 548 }; 549 550 ldoln_reg: ldoln { 551 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ 552 regulator-name = "ldoln"; 553 regulator-min-microvolt = <1800000>; 554 regulator-max-microvolt = <1800000>; 555 regulator-always-on; 556 regulator-boot-on; 557 }; 558 559 ldousb_reg: ldousb { 560 /* VDDA_3V_USB: VDDA_USBHS33 */ 561 regulator-name = "ldousb"; 562 regulator-min-microvolt = <3250000>; 563 regulator-max-microvolt = <3250000>; 564 regulator-always-on; 565 regulator-boot-on; 566 }; 567 568 regen3_reg: regen3 { 569 /* REGEN3 controls LDO9 supply to card */ 570 regulator-name = "regen3"; 571 regulator-always-on; 572 regulator-boot-on; 573 }; 574 }; 575 }; 576 577 palmas_power_button: palmas_power_button { 578 compatible = "ti,palmas-pwrbutton"; 579 interrupt-parent = <&palmas>; 580 interrupts = <1 IRQ_TYPE_EDGE_FALLING>; 581 wakeup-source; 582 }; 583 }; 584 585 twl6040: twl@4b { 586 compatible = "ti,twl6040"; 587 reg = <0x4b>; 588 589 pinctrl-names = "default"; 590 pinctrl-0 = <&twl6040_pins>; 591 592 interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */ 593 ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */ 594 595 vio-supply = <&smps7_reg>; 596 v2v1-supply = <&smps9_reg>; 597 enable-active-high; 598 599 clocks = <&clk32kgaudio>; 600 clock-names = "clk32k"; 601 }; 602}; 603 604&mcpdm { 605 pinctrl-names = "default"; 606 pinctrl-0 = <&mcpdm_pins>; 607 status = "okay"; 608}; 609 610&mcbsp1 { 611 pinctrl-names = "default"; 612 pinctrl-0 = <&mcbsp1_pins>; 613 status = "okay"; 614}; 615 616&mcbsp2 { 617 pinctrl-names = "default"; 618 pinctrl-0 = <&mcbsp2_pins>; 619 status = "okay"; 620}; 621 622&usbhshost { 623 port2-mode = "ehci-hsic"; 624 port3-mode = "ehci-hsic"; 625}; 626 627&usbhsehci { 628 phys = <0 &hsusb2_phy &hsusb3_phy>; 629}; 630 631&usb3 { 632 extcon = <&extcon_usb3>; 633 vbus-supply = <&smps10_out1_reg>; 634}; 635 636&mcspi1 { 637 638}; 639 640&mcspi2 { 641 pinctrl-names = "default"; 642 pinctrl-0 = <&mcspi2_pins>; 643}; 644 645&mcspi3 { 646 pinctrl-names = "default"; 647 pinctrl-0 = <&mcspi3_pins>; 648}; 649 650&uart1 { 651 pinctrl-names = "default"; 652 pinctrl-0 = <&uart1_pins>; 653}; 654 655&uart3 { 656 pinctrl-names = "default"; 657 pinctrl-0 = <&uart3_pins>; 658 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, 659 <&omap5_pmx_core 0x19c>; 660}; 661 662&uart5 { 663 pinctrl-names = "default"; 664 pinctrl-0 = <&uart5_pins>; 665}; 666 667&cpu0 { 668 cpu0-supply = <&smps123_reg>; 669}; 670 671&dss { 672 status = "ok"; 673}; 674 675&hdmi { 676 status = "ok"; 677 678 /* vdda-supply populated in board specific dts file */ 679 680 pinctrl-names = "default"; 681 pinctrl-0 = <&dss_hdmi_pins>; 682 683 port { 684 hdmi_out: endpoint { 685 remote-endpoint = <&tpd12s015_in>; 686 }; 687 }; 688}; 689