1/* 2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ 3 * 4 * This program is free software; you can redistribute it and/or modify 5 * it under the terms of the GNU General Public License version 2 as 6 * published by the Free Software Foundation. 7 */ 8#include "omap5.dtsi" 9#include <dt-bindings/interrupt-controller/irq.h> 10#include <dt-bindings/interrupt-controller/arm-gic.h> 11 12/ { 13 aliases { 14 display0 = &hdmi0; 15 }; 16 17 vmain: fixedregulator-vmain { 18 compatible = "regulator-fixed"; 19 regulator-name = "vmain"; 20 regulator-min-microvolt = <5000000>; 21 regulator-max-microvolt = <5000000>; 22 }; 23 24 vsys_cobra: fixedregulator-vsys_cobra { 25 compatible = "regulator-fixed"; 26 regulator-name = "vsys_cobra"; 27 vin-supply = <&vmain>; 28 regulator-min-microvolt = <5000000>; 29 regulator-max-microvolt = <5000000>; 30 }; 31 32 vdds_1v8_main: fixedregulator-vdds_1v8_main { 33 compatible = "regulator-fixed"; 34 regulator-name = "vdds_1v8_main"; 35 vin-supply = <&smps7_reg>; 36 regulator-min-microvolt = <1800000>; 37 regulator-max-microvolt = <1800000>; 38 }; 39 40 vmmcsd_fixed: fixedregulator-mmcsd { 41 compatible = "regulator-fixed"; 42 regulator-name = "vmmcsd_fixed"; 43 regulator-min-microvolt = <3000000>; 44 regulator-max-microvolt = <3000000>; 45 }; 46 47 mmc3_pwrseq: sdhci0_pwrseq { 48 compatible = "mmc-pwrseq-simple"; 49 clocks = <&clk32kgaudio>; 50 clock-names = "ext_clock"; 51 }; 52 53 vmmcsdio_fixed: fixedregulator-mmcsdio { 54 compatible = "regulator-fixed"; 55 regulator-name = "vmmcsdio_fixed"; 56 regulator-min-microvolt = <1800000>; 57 regulator-max-microvolt = <1800000>; 58 gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */ 59 enable-active-high; 60 startup-delay-us = <70000>; 61 pinctrl-names = "default"; 62 pinctrl-0 = <&wlan_pins>; 63 }; 64 65 /* HS USB Host PHY on PORT 2 */ 66 hsusb2_phy: hsusb2_phy { 67 compatible = "usb-nop-xceiv"; 68 reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ 69 clocks = <&auxclk1_ck>; 70 clock-names = "main_clk"; 71 clock-frequency = <19200000>; 72 }; 73 74 /* HS USB Host PHY on PORT 3 */ 75 hsusb3_phy: hsusb3_phy { 76 compatible = "usb-nop-xceiv"; 77 reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ 78 }; 79 80 tpd12s015: encoder { 81 compatible = "ti,tpd12s015"; 82 83 pinctrl-names = "default"; 84 pinctrl-0 = <&tpd12s015_pins>; 85 86 /* gpios defined in the board specific dts */ 87 88 ports { 89 #address-cells = <1>; 90 #size-cells = <0>; 91 92 port@0 { 93 reg = <0>; 94 95 tpd12s015_in: endpoint { 96 remote-endpoint = <&hdmi_out>; 97 }; 98 }; 99 100 port@1 { 101 reg = <1>; 102 103 tpd12s015_out: endpoint { 104 remote-endpoint = <&hdmi_connector_in>; 105 }; 106 }; 107 }; 108 }; 109 110 hdmi0: connector { 111 compatible = "hdmi-connector"; 112 label = "hdmi"; 113 114 type = "b"; 115 116 port { 117 hdmi_connector_in: endpoint { 118 remote-endpoint = <&tpd12s015_out>; 119 }; 120 }; 121 }; 122 123 sound: sound { 124 compatible = "ti,abe-twl6040"; 125 ti,model = "omap5-uevm"; 126 127 ti,jack-detection; 128 ti,mclk-freq = <19200000>; 129 130 ti,mcpdm = <&mcpdm>; 131 132 ti,twl6040 = <&twl6040>; 133 134 /* Audio routing */ 135 ti,audio-routing = 136 "Headset Stereophone", "HSOL", 137 "Headset Stereophone", "HSOR", 138 "Line Out", "AUXL", 139 "Line Out", "AUXR", 140 "HSMIC", "Headset Mic", 141 "Headset Mic", "Headset Mic Bias", 142 "AFML", "Line In", 143 "AFMR", "Line In"; 144 }; 145}; 146 147&gpio8 { 148 /* TI trees use GPIO instead of msecure, see also muxing */ 149 p234 { 150 gpio-hog; 151 gpios = <10 GPIO_ACTIVE_HIGH>; 152 output-high; 153 line-name = "gpio8_234/msecure"; 154 }; 155}; 156 157&omap5_pmx_core { 158 pinctrl-names = "default"; 159 pinctrl-0 = < 160 &usbhost_pins 161 &led_gpio_pins 162 >; 163 164 twl6040_pins: pinmux_twl6040_pins { 165 pinctrl-single,pins = < 166 OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ 167 >; 168 }; 169 170 mcpdm_pins: pinmux_mcpdm_pins { 171 pinctrl-single,pins = < 172 OMAP5_IOPAD(0x182, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ 173 OMAP5_IOPAD(0x19c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ 174 OMAP5_IOPAD(0x19e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ 175 OMAP5_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ 176 OMAP5_IOPAD(0x1a2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ 177 >; 178 }; 179 180 mcbsp1_pins: pinmux_mcbsp1_pins { 181 pinctrl-single,pins = < 182 OMAP5_IOPAD(0x18c, PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ 183 OMAP5_IOPAD(0x18e, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ 184 OMAP5_IOPAD(0x190, PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ 185 OMAP5_IOPAD(0x192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ 186 >; 187 }; 188 189 mcbsp2_pins: pinmux_mcbsp2_pins { 190 pinctrl-single,pins = < 191 OMAP5_IOPAD(0x194, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ 192 OMAP5_IOPAD(0x196, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ 193 OMAP5_IOPAD(0x198, PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ 194 OMAP5_IOPAD(0x19a, PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ 195 >; 196 }; 197 198 i2c1_pins: pinmux_i2c1_pins { 199 pinctrl-single,pins = < 200 OMAP5_IOPAD(0x1f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ 201 OMAP5_IOPAD(0x1f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ 202 >; 203 }; 204 205 mcspi2_pins: pinmux_mcspi2_pins { 206 pinctrl-single,pins = < 207 OMAP5_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ 208 OMAP5_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ 209 OMAP5_IOPAD(0x100, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ 210 OMAP5_IOPAD(0x102, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ 211 >; 212 }; 213 214 mcspi3_pins: pinmux_mcspi3_pins { 215 pinctrl-single,pins = < 216 OMAP5_IOPAD(0x0b8, PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ 217 OMAP5_IOPAD(0x0ba, PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ 218 OMAP5_IOPAD(0x0bc, PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ 219 OMAP5_IOPAD(0x0be, PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ 220 >; 221 }; 222 223 mmc3_pins: pinmux_mmc3_pins { 224 pinctrl-single,pins = < 225 OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ 226 OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ 227 OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ 228 OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ 229 OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ 230 OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ 231 >; 232 }; 233 234 wlan_pins: pinmux_wlan_pins { 235 pinctrl-single,pins = < 236 OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */ 237 >; 238 }; 239 240 /* TI trees use GPIO mode; msecure mode does not work reliably? */ 241 palmas_msecure_pins: palmas_msecure_pins { 242 pinctrl-single,pins = < 243 OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */ 244 >; 245 }; 246 247 usbhost_pins: pinmux_usbhost_pins { 248 pinctrl-single,pins = < 249 OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ 250 OMAP5_IOPAD(0x0c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ 251 252 OMAP5_IOPAD(0x1de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ 253 OMAP5_IOPAD(0x1e0, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ 254 255 OMAP5_IOPAD(0x0b0, PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ 256 OMAP5_IOPAD(0x0ae, PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ 257 >; 258 }; 259 260 led_gpio_pins: pinmux_led_gpio_pins { 261 pinctrl-single,pins = < 262 OMAP5_IOPAD(0x1d6, PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ 263 >; 264 }; 265 266 uart1_pins: pinmux_uart1_pins { 267 pinctrl-single,pins = < 268 OMAP5_IOPAD(0x0a0, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ 269 OMAP5_IOPAD(0x0a2, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ 270 OMAP5_IOPAD(0x0a4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ 271 OMAP5_IOPAD(0x0a6, PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ 272 >; 273 }; 274 275 uart3_pins: pinmux_uart3_pins { 276 pinctrl-single,pins = < 277 OMAP5_IOPAD(0x1da, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ 278 OMAP5_IOPAD(0x1dc, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ 279 >; 280 }; 281 282 uart5_pins: pinmux_uart5_pins { 283 pinctrl-single,pins = < 284 OMAP5_IOPAD(0x1b0, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ 285 OMAP5_IOPAD(0x1b2, PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ 286 OMAP5_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ 287 OMAP5_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ 288 >; 289 }; 290 291 dss_hdmi_pins: pinmux_dss_hdmi_pins { 292 pinctrl-single,pins = < 293 OMAP5_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ 294 OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ 295 OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ 296 >; 297 }; 298 299 tpd12s015_pins: pinmux_tpd12s015_pins { 300 pinctrl-single,pins = < 301 OMAP5_IOPAD(0x13e, PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ 302 >; 303 }; 304}; 305 306&omap5_pmx_wkup { 307 pinctrl-names = "default"; 308 pinctrl-0 = < 309 &usbhost_wkup_pins 310 >; 311 312 palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins { 313 pinctrl-single,pins = < 314 OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */ 315 >; 316 }; 317 318 usbhost_wkup_pins: pinmux_usbhost_wkup_pins { 319 pinctrl-single,pins = < 320 OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ 321 >; 322 }; 323 324 wlcore_irq_pin: pinmux_wlcore_irq_pin { 325 pinctrl-single,pins = < 326 OMAP5_IOPAD(0x40, PIN_INPUT | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ 327 >; 328 }; 329}; 330 331&mmc1 { 332 vmmc-supply = <&ldo9_reg>; 333 bus-width = <4>; 334}; 335 336&mmc2 { 337 vmmc-supply = <&vmmcsd_fixed>; 338 bus-width = <8>; 339 ti,non-removable; 340}; 341 342&mmc3 { 343 vmmc-supply = <&vmmcsdio_fixed>; 344 mmc-pwrseq = <&mmc3_pwrseq>; 345 bus-width = <4>; 346 non-removable; 347 cap-power-off-card; 348 pinctrl-names = "default"; 349 pinctrl-0 = <&mmc3_pins>; 350 interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH 351 &omap5_pmx_core 0x16a>; 352 353 #address-cells = <1>; 354 #size-cells = <0>; 355 wlcore: wlcore@2 { 356 compatible = "ti,wl1271"; 357 reg = <2>; 358 pinctrl-names = "default"; 359 pinctrl-0 = <&wlcore_irq_pin>; 360 interrupt-parent = <&gpio1>; 361 interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */ 362 ref-clock-frequency = <26000000>; 363 }; 364}; 365 366&mmc4 { 367 status = "disabled"; 368}; 369 370&mmc5 { 371 status = "disabled"; 372}; 373 374&i2c1 { 375 pinctrl-names = "default"; 376 pinctrl-0 = <&i2c1_pins>; 377 378 clock-frequency = <400000>; 379 380 palmas: palmas@48 { 381 compatible = "ti,palmas"; 382 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ 383 reg = <0x48>; 384 interrupt-controller; 385 #interrupt-cells = <2>; 386 ti,system-power-controller; 387 ti,mux-pad1 = <0xa1>; 388 ti,mux-pad2 = <0x1b>; 389 pinctrl-names = "default"; 390 pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>; 391 392 palmas_gpio: gpio { 393 compatible = "ti,palmas-gpio"; 394 gpio-controller; 395 #gpio-cells = <2>; 396 }; 397 398 extcon_usb3: palmas_usb { 399 compatible = "ti,palmas-usb-vid"; 400 ti,enable-vbus-detection; 401 ti,enable-id-detection; 402 ti,wakeup; 403 id-gpios = <&palmas_gpio 0 GPIO_ACTIVE_HIGH>; 404 }; 405 406 clk32kgaudio: palmas_clk32k@1 { 407 compatible = "ti,palmas-clk32kgaudio"; 408 #clock-cells = <0>; 409 }; 410 411 rtc { 412 compatible = "ti,palmas-rtc"; 413 interrupt-parent = <&palmas>; 414 interrupts = <8 IRQ_TYPE_NONE>; 415 ti,backup-battery-chargeable; 416 ti,backup-battery-charge-high-current; 417 }; 418 419 gpadc: gpadc { 420 compatible = "ti,palmas-gpadc"; 421 interrupts = <18 0 422 16 0 423 17 0>; 424 #io-channel-cells = <1>; 425 ti,channel0-current-microamp = <5>; 426 ti,channel3-current-microamp = <10>; 427 }; 428 429 palmas_pmic { 430 compatible = "ti,palmas-pmic"; 431 interrupt-parent = <&palmas>; 432 interrupts = <14 IRQ_TYPE_NONE>; 433 interrupt-names = "short-irq"; 434 435 ti,ldo6-vibrator; 436 437 smps123-in-supply = <&vsys_cobra>; 438 smps45-in-supply = <&vsys_cobra>; 439 smps6-in-supply = <&vsys_cobra>; 440 smps7-in-supply = <&vsys_cobra>; 441 smps8-in-supply = <&vsys_cobra>; 442 smps9-in-supply = <&vsys_cobra>; 443 smps10_out2-in-supply = <&vsys_cobra>; 444 smps10_out1-in-supply = <&vsys_cobra>; 445 ldo1-in-supply = <&vsys_cobra>; 446 ldo2-in-supply = <&vsys_cobra>; 447 ldo3-in-supply = <&vdds_1v8_main>; 448 ldo4-in-supply = <&vdds_1v8_main>; 449 ldo5-in-supply = <&vsys_cobra>; 450 ldo6-in-supply = <&vdds_1v8_main>; 451 ldo7-in-supply = <&vsys_cobra>; 452 ldo8-in-supply = <&vsys_cobra>; 453 ldo9-in-supply = <&vmmcsd_fixed>; 454 ldoln-in-supply = <&vsys_cobra>; 455 ldousb-in-supply = <&vsys_cobra>; 456 457 regulators { 458 smps123_reg: smps123 { 459 /* VDD_OPP_MPU */ 460 regulator-name = "smps123"; 461 regulator-min-microvolt = < 600000>; 462 regulator-max-microvolt = <1500000>; 463 regulator-always-on; 464 regulator-boot-on; 465 }; 466 467 smps45_reg: smps45 { 468 /* VDD_OPP_MM */ 469 regulator-name = "smps45"; 470 regulator-min-microvolt = < 600000>; 471 regulator-max-microvolt = <1310000>; 472 regulator-always-on; 473 regulator-boot-on; 474 }; 475 476 smps6_reg: smps6 { 477 /* VDD_DDR3 - over VDD_SMPS6 */ 478 regulator-name = "smps6"; 479 regulator-min-microvolt = <1350000>; 480 regulator-max-microvolt = <1350000>; 481 regulator-always-on; 482 regulator-boot-on; 483 }; 484 485 smps7_reg: smps7 { 486 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ 487 regulator-name = "smps7"; 488 regulator-min-microvolt = <1800000>; 489 regulator-max-microvolt = <1800000>; 490 regulator-always-on; 491 regulator-boot-on; 492 }; 493 494 smps8_reg: smps8 { 495 /* VDD_OPP_CORE */ 496 regulator-name = "smps8"; 497 regulator-min-microvolt = < 600000>; 498 regulator-max-microvolt = <1310000>; 499 regulator-always-on; 500 regulator-boot-on; 501 }; 502 503 smps9_reg: smps9 { 504 /* VDDA_2v1_AUD over VDD_2v1 */ 505 regulator-name = "smps9"; 506 regulator-min-microvolt = <2100000>; 507 regulator-max-microvolt = <2100000>; 508 ti,smps-range = <0x80>; 509 }; 510 511 smps10_out2_reg: smps10_out2 { 512 /* VBUS_5V_OTG */ 513 regulator-name = "smps10_out2"; 514 regulator-min-microvolt = <5000000>; 515 regulator-max-microvolt = <5000000>; 516 regulator-always-on; 517 regulator-boot-on; 518 }; 519 520 smps10_out1_reg: smps10_out1 { 521 /* VBUS_5V_OTG */ 522 regulator-name = "smps10_out1"; 523 regulator-min-microvolt = <5000000>; 524 regulator-max-microvolt = <5000000>; 525 }; 526 527 ldo1_reg: ldo1 { 528 /* VDDAPHY_CAM: vdda_csiport */ 529 regulator-name = "ldo1"; 530 regulator-min-microvolt = <1800000>; 531 regulator-max-microvolt = <1800000>; 532 }; 533 534 ldo2_reg: ldo2 { 535 /* VCC_2V8_DISP: Does not go anywhere */ 536 regulator-name = "ldo2"; 537 regulator-min-microvolt = <2800000>; 538 regulator-max-microvolt = <2800000>; 539 /* Unused */ 540 status = "disabled"; 541 }; 542 543 ldo3_reg: ldo3 { 544 /* VDDAPHY_MDM: vdda_lli */ 545 regulator-name = "ldo3"; 546 regulator-min-microvolt = <1500000>; 547 regulator-max-microvolt = <1500000>; 548 regulator-boot-on; 549 /* Only if Modem is used */ 550 status = "disabled"; 551 }; 552 553 ldo4_reg: ldo4 { 554 /* VDDAPHY_DISP: vdda_dsiport/hdmi */ 555 regulator-name = "ldo4"; 556 regulator-min-microvolt = <1800000>; 557 regulator-max-microvolt = <1800000>; 558 }; 559 560 ldo5_reg: ldo5 { 561 /* VDDA_1V8_PHY: usb/sata/hdmi.. */ 562 regulator-name = "ldo5"; 563 regulator-min-microvolt = <1800000>; 564 regulator-max-microvolt = <1800000>; 565 regulator-always-on; 566 regulator-boot-on; 567 }; 568 569 ldo6_reg: ldo6 { 570 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ 571 regulator-name = "ldo6"; 572 regulator-min-microvolt = <1200000>; 573 regulator-max-microvolt = <1200000>; 574 regulator-always-on; 575 regulator-boot-on; 576 }; 577 578 ldo7_reg: ldo7 { 579 /* VDD_VPP: vpp1 */ 580 regulator-name = "ldo7"; 581 regulator-min-microvolt = <2000000>; 582 regulator-max-microvolt = <2000000>; 583 /* Only for efuse reprograming! */ 584 status = "disabled"; 585 }; 586 587 ldo8_reg: ldo8 { 588 /* VDD_3v0: Does not go anywhere */ 589 regulator-name = "ldo8"; 590 regulator-min-microvolt = <3000000>; 591 regulator-max-microvolt = <3000000>; 592 regulator-boot-on; 593 /* Unused */ 594 status = "disabled"; 595 }; 596 597 ldo9_reg: ldo9 { 598 /* VCC_DV_SDIO: vdds_sdcard */ 599 regulator-name = "ldo9"; 600 regulator-min-microvolt = <1800000>; 601 regulator-max-microvolt = <3000000>; 602 regulator-boot-on; 603 }; 604 605 ldoln_reg: ldoln { 606 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ 607 regulator-name = "ldoln"; 608 regulator-min-microvolt = <1800000>; 609 regulator-max-microvolt = <1800000>; 610 regulator-always-on; 611 regulator-boot-on; 612 }; 613 614 ldousb_reg: ldousb { 615 /* VDDA_3V_USB: VDDA_USBHS33 */ 616 regulator-name = "ldousb"; 617 regulator-min-microvolt = <3250000>; 618 regulator-max-microvolt = <3250000>; 619 regulator-always-on; 620 regulator-boot-on; 621 }; 622 623 regen3_reg: regen3 { 624 /* REGEN3 controls LDO9 supply to card */ 625 regulator-name = "regen3"; 626 regulator-always-on; 627 regulator-boot-on; 628 }; 629 }; 630 }; 631 632 palmas_power_button: palmas_power_button { 633 compatible = "ti,palmas-pwrbutton"; 634 interrupt-parent = <&palmas>; 635 interrupts = <1 IRQ_TYPE_EDGE_FALLING>; 636 wakeup-source; 637 }; 638 }; 639 640 twl6040: twl@4b { 641 compatible = "ti,twl6040"; 642 #clock-cells = <0>; 643 reg = <0x4b>; 644 645 pinctrl-names = "default"; 646 pinctrl-0 = <&twl6040_pins>; 647 648 interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */ 649 650 /* audpwron gpio defined in the board specific dts */ 651 652 vio-supply = <&smps7_reg>; 653 v2v1-supply = <&smps9_reg>; 654 enable-active-high; 655 656 clocks = <&clk32kgaudio>; 657 clock-names = "clk32k"; 658 }; 659}; 660 661&mcpdm { 662 pinctrl-names = "default"; 663 pinctrl-0 = <&mcpdm_pins>; 664 665 clocks = <&twl6040>; 666 clock-names = "pdmclk"; 667 668 status = "okay"; 669}; 670 671&mcbsp1 { 672 pinctrl-names = "default"; 673 pinctrl-0 = <&mcbsp1_pins>; 674 status = "okay"; 675}; 676 677&mcbsp2 { 678 pinctrl-names = "default"; 679 pinctrl-0 = <&mcbsp2_pins>; 680 status = "okay"; 681}; 682 683&usbhshost { 684 port2-mode = "ehci-hsic"; 685 port3-mode = "ehci-hsic"; 686}; 687 688&usbhsehci { 689 phys = <0 &hsusb2_phy &hsusb3_phy>; 690}; 691 692&usb3 { 693 extcon = <&extcon_usb3>; 694 vbus-supply = <&smps10_out1_reg>; 695}; 696 697&mcspi1 { 698 699}; 700 701&mcspi2 { 702 pinctrl-names = "default"; 703 pinctrl-0 = <&mcspi2_pins>; 704}; 705 706&mcspi3 { 707 pinctrl-names = "default"; 708 pinctrl-0 = <&mcspi3_pins>; 709}; 710 711&uart1 { 712 pinctrl-names = "default"; 713 pinctrl-0 = <&uart1_pins>; 714}; 715 716&uart3 { 717 pinctrl-names = "default"; 718 pinctrl-0 = <&uart3_pins>; 719 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, 720 <&omap5_pmx_core 0x19c>; 721}; 722 723&uart5 { 724 pinctrl-names = "default"; 725 pinctrl-0 = <&uart5_pins>; 726}; 727 728&cpu0 { 729 cpu0-supply = <&smps123_reg>; 730}; 731 732&dss { 733 status = "ok"; 734}; 735 736&hdmi { 737 status = "ok"; 738 739 /* vdda-supply populated in board specific dts file */ 740 741 pinctrl-names = "default"; 742 pinctrl-0 = <&dss_hdmi_pins>; 743 744 port { 745 hdmi_out: endpoint { 746 remote-endpoint = <&tpd12s015_in>; 747 }; 748 }; 749}; 750