• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1/*
2 *  BSD LICENSE
3 *
4 *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
5 *
6 *  Redistribution and use in source and binary forms, with or without
7 *  modification, are permitted provided that the following conditions
8 *  are met:
9 *
10 *    * Redistributions of source code must retain the above copyright
11 *      notice, this list of conditions and the following disclaimer.
12 *    * Redistributions in binary form must reproduce the above copyright
13 *      notice, this list of conditions and the following disclaimer in
14 *      the documentation and/or other materials provided with the
15 *      distribution.
16 *    * Neither the name of Broadcom Corporation nor the names of its
17 *      contributors may be used to endorse or promote products derived
18 *      from this software without specific prior written permission.
19 *
20 *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
21 *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
22 *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
23 *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
24 *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
25 *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
26 *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
27 *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
28 *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
29 *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
31 */
32
33/dts-v1/;
34
35#include "ns2.dtsi"
36
37/ {
38	model = "Broadcom NS2 SVK";
39	compatible = "brcm,ns2-svk", "brcm,ns2";
40
41	aliases {
42		serial0 = &uart3;
43		serial1 = &uart0;
44		serial2 = &uart1;
45		serial3 = &uart2;
46	};
47
48	chosen {
49		stdout-path = "serial0:115200n8";
50		bootargs = "earlycon=uart8250,mmio32,0x66130000";
51	};
52
53	memory {
54		device_type = "memory";
55		reg = <0x000000000 0x80000000 0x00000000 0x40000000>;
56	};
57};
58
59&pci_phy0 {
60	status = "ok";
61};
62
63&pci_phy1 {
64	status = "ok";
65};
66
67&pcie0 {
68	status = "ok";
69};
70
71&pcie4 {
72	status = "ok";
73};
74
75&i2c0 {
76	status = "ok";
77};
78
79&i2c1 {
80	status = "ok";
81};
82
83&uart0 {
84	status = "ok";
85};
86
87&uart1 {
88	status = "ok";
89};
90
91&uart2 {
92	status = "ok";
93};
94
95&uart3 {
96	status = "ok";
97};
98
99&ssp0 {
100	status = "ok";
101
102	slic@0 {
103		compatible = "silabs,si3226x";
104		reg = <0>;
105		spi-max-frequency = <5000000>;
106		spi-cpha = <1>;
107		spi-cpol = <1>;
108		pl022,hierarchy = <0>;
109		pl022,interface = <0>;
110		pl022,slave-tx-disable = <0>;
111		pl022,com-mode = <0>;
112		pl022,rx-level-trig = <1>;
113		pl022,tx-level-trig = <1>;
114		pl022,ctrl-len = <11>;
115		pl022,wait-state = <0>;
116		pl022,duplex = <0>;
117	};
118};
119
120&ssp1 {
121	status = "ok";
122
123	at25@0 {
124		compatible = "atmel,at25";
125		reg = <0>;
126		spi-max-frequency = <5000000>;
127		at25,byte-len = <0x8000>;
128		at25,addr-mode = <2>;
129		at25,page-size = <64>;
130		spi-cpha = <1>;
131		spi-cpol = <1>;
132		pl022,hierarchy = <0>;
133		pl022,interface = <0>;
134		pl022,slave-tx-disable = <0>;
135		pl022,com-mode = <0>;
136		pl022,rx-level-trig = <1>;
137		pl022,tx-level-trig = <1>;
138		pl022,ctrl-len = <11>;
139		pl022,wait-state = <0>;
140		pl022,duplex = <0>;
141	};
142};
143
144&sata_phy0 {
145	status = "ok";
146};
147
148&sata_phy1 {
149	status = "ok";
150};
151
152&sata {
153	status = "ok";
154};
155
156&sdio0 {
157	status = "ok";
158};
159
160&nand {
161	nandcs@0 {
162		compatible = "brcm,nandcs";
163		reg = <0>;
164		nand-ecc-mode = "hw";
165		nand-ecc-strength = <8>;
166		nand-ecc-step-size = <512>;
167		nand-bus-width = <16>;
168		brcm,nand-oob-sector-size = <16>;
169		#address-cells = <1>;
170		#size-cells = <1>;
171	};
172};
173
174&mdio_mux_iproc {
175	mdio@10 {
176		gphy0: eth-phy@10 {
177			reg = <0x10>;
178		};
179	};
180};
181
182&pinctrl {
183	pinctrl-names = "default";
184	pinctrl-0 = <&nand_sel>;
185	nand_sel: nand_sel {
186		function = "nand";
187		groups = "nand_grp";
188	};
189};
190