1 /*
2 * Cadence UART driver (found in Xilinx Zynq)
3 *
4 * 2011 - 2014 (C) Xilinx Inc.
5 *
6 * This program is free software; you can redistribute it
7 * and/or modify it under the terms of the GNU General Public
8 * License as published by the Free Software Foundation;
9 * either version 2 of the License, or (at your option) any
10 * later version.
11 *
12 * This driver has originally been pushed by Xilinx using a Zynq-branding. This
13 * still shows in the naming of this file, the kconfig symbols and some symbols
14 * in the code.
15 */
16
17 #if defined(CONFIG_SERIAL_XILINX_PS_UART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
18 #define SUPPORT_SYSRQ
19 #endif
20
21 #include <linux/platform_device.h>
22 #include <linux/serial.h>
23 #include <linux/console.h>
24 #include <linux/serial_core.h>
25 #include <linux/slab.h>
26 #include <linux/tty.h>
27 #include <linux/tty_flip.h>
28 #include <linux/clk.h>
29 #include <linux/irq.h>
30 #include <linux/io.h>
31 #include <linux/of.h>
32 #include <linux/module.h>
33
34 #define CDNS_UART_TTY_NAME "ttyPS"
35 #define CDNS_UART_NAME "xuartps"
36 #define CDNS_UART_MAJOR 0 /* use dynamic node allocation */
37 #define CDNS_UART_MINOR 0 /* works best with devtmpfs */
38 #define CDNS_UART_NR_PORTS 2
39 #define CDNS_UART_FIFO_SIZE 64 /* FIFO size */
40 #define CDNS_UART_REGISTER_SPACE 0x1000
41
42 /* Rx Trigger level */
43 static int rx_trigger_level = 56;
44 module_param(rx_trigger_level, uint, S_IRUGO);
45 MODULE_PARM_DESC(rx_trigger_level, "Rx trigger level, 1-63 bytes");
46
47 /* Rx Timeout */
48 static int rx_timeout = 10;
49 module_param(rx_timeout, uint, S_IRUGO);
50 MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
51
52 /* Register offsets for the UART. */
53 #define CDNS_UART_CR 0x00 /* Control Register */
54 #define CDNS_UART_MR 0x04 /* Mode Register */
55 #define CDNS_UART_IER 0x08 /* Interrupt Enable */
56 #define CDNS_UART_IDR 0x0C /* Interrupt Disable */
57 #define CDNS_UART_IMR 0x10 /* Interrupt Mask */
58 #define CDNS_UART_ISR 0x14 /* Interrupt Status */
59 #define CDNS_UART_BAUDGEN 0x18 /* Baud Rate Generator */
60 #define CDNS_UART_RXTOUT 0x1C /* RX Timeout */
61 #define CDNS_UART_RXWM 0x20 /* RX FIFO Trigger Level */
62 #define CDNS_UART_MODEMCR 0x24 /* Modem Control */
63 #define CDNS_UART_MODEMSR 0x28 /* Modem Status */
64 #define CDNS_UART_SR 0x2C /* Channel Status */
65 #define CDNS_UART_FIFO 0x30 /* FIFO */
66 #define CDNS_UART_BAUDDIV 0x34 /* Baud Rate Divider */
67 #define CDNS_UART_FLOWDEL 0x38 /* Flow Delay */
68 #define CDNS_UART_IRRX_PWIDTH 0x3C /* IR Min Received Pulse Width */
69 #define CDNS_UART_IRTX_PWIDTH 0x40 /* IR Transmitted pulse Width */
70 #define CDNS_UART_TXWM 0x44 /* TX FIFO Trigger Level */
71 #define CDNS_UART_RXBS 0x48 /* RX FIFO byte status register */
72
73 /* Control Register Bit Definitions */
74 #define CDNS_UART_CR_STOPBRK 0x00000100 /* Stop TX break */
75 #define CDNS_UART_CR_STARTBRK 0x00000080 /* Set TX break */
76 #define CDNS_UART_CR_TX_DIS 0x00000020 /* TX disabled. */
77 #define CDNS_UART_CR_TX_EN 0x00000010 /* TX enabled */
78 #define CDNS_UART_CR_RX_DIS 0x00000008 /* RX disabled. */
79 #define CDNS_UART_CR_RX_EN 0x00000004 /* RX enabled */
80 #define CDNS_UART_CR_TXRST 0x00000002 /* TX logic reset */
81 #define CDNS_UART_CR_RXRST 0x00000001 /* RX logic reset */
82 #define CDNS_UART_CR_RST_TO 0x00000040 /* Restart Timeout Counter */
83 #define CDNS_UART_RXBS_PARITY 0x00000001 /* Parity error status */
84 #define CDNS_UART_RXBS_FRAMING 0x00000002 /* Framing error status */
85 #define CDNS_UART_RXBS_BRK 0x00000004 /* Overrun error status */
86
87 /*
88 * Mode Register:
89 * The mode register (MR) defines the mode of transfer as well as the data
90 * format. If this register is modified during transmission or reception,
91 * data validity cannot be guaranteed.
92 */
93 #define CDNS_UART_MR_CLKSEL 0x00000001 /* Pre-scalar selection */
94 #define CDNS_UART_MR_CHMODE_L_LOOP 0x00000200 /* Local loop back mode */
95 #define CDNS_UART_MR_CHMODE_NORM 0x00000000 /* Normal mode */
96
97 #define CDNS_UART_MR_STOPMODE_2_BIT 0x00000080 /* 2 stop bits */
98 #define CDNS_UART_MR_STOPMODE_1_BIT 0x00000000 /* 1 stop bit */
99
100 #define CDNS_UART_MR_PARITY_NONE 0x00000020 /* No parity mode */
101 #define CDNS_UART_MR_PARITY_MARK 0x00000018 /* Mark parity mode */
102 #define CDNS_UART_MR_PARITY_SPACE 0x00000010 /* Space parity mode */
103 #define CDNS_UART_MR_PARITY_ODD 0x00000008 /* Odd parity mode */
104 #define CDNS_UART_MR_PARITY_EVEN 0x00000000 /* Even parity mode */
105
106 #define CDNS_UART_MR_CHARLEN_6_BIT 0x00000006 /* 6 bits data */
107 #define CDNS_UART_MR_CHARLEN_7_BIT 0x00000004 /* 7 bits data */
108 #define CDNS_UART_MR_CHARLEN_8_BIT 0x00000000 /* 8 bits data */
109
110 /*
111 * Interrupt Registers:
112 * Interrupt control logic uses the interrupt enable register (IER) and the
113 * interrupt disable register (IDR) to set the value of the bits in the
114 * interrupt mask register (IMR). The IMR determines whether to pass an
115 * interrupt to the interrupt status register (ISR).
116 * Writing a 1 to IER Enables an interrupt, writing a 1 to IDR disables an
117 * interrupt. IMR and ISR are read only, and IER and IDR are write only.
118 * Reading either IER or IDR returns 0x00.
119 * All four registers have the same bit definitions.
120 */
121 #define CDNS_UART_IXR_TOUT 0x00000100 /* RX Timeout error interrupt */
122 #define CDNS_UART_IXR_PARITY 0x00000080 /* Parity error interrupt */
123 #define CDNS_UART_IXR_FRAMING 0x00000040 /* Framing error interrupt */
124 #define CDNS_UART_IXR_OVERRUN 0x00000020 /* Overrun error interrupt */
125 #define CDNS_UART_IXR_TXFULL 0x00000010 /* TX FIFO Full interrupt */
126 #define CDNS_UART_IXR_TXEMPTY 0x00000008 /* TX FIFO empty interrupt */
127 #define CDNS_UART_ISR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt */
128 #define CDNS_UART_IXR_RXTRIG 0x00000001 /* RX FIFO trigger interrupt */
129 #define CDNS_UART_IXR_RXFULL 0x00000004 /* RX FIFO full interrupt. */
130 #define CDNS_UART_IXR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt. */
131 #define CDNS_UART_IXR_MASK 0x00001FFF /* Valid bit mask */
132
133 /*
134 * Do not enable parity error interrupt for the following
135 * reason: When parity error interrupt is enabled, each Rx
136 * parity error always results in 2 events. The first one
137 * being parity error interrupt and the second one with a
138 * proper Rx interrupt with the incoming data. Disabling
139 * parity error interrupt ensures better handling of parity
140 * error events. With this change, for a parity error case, we
141 * get a Rx interrupt with parity error set in ISR register
142 * and we still handle parity errors in the desired way.
143 */
144
145 #define CDNS_UART_RX_IRQS (CDNS_UART_IXR_FRAMING | \
146 CDNS_UART_IXR_OVERRUN | \
147 CDNS_UART_IXR_RXTRIG | \
148 CDNS_UART_IXR_TOUT)
149
150 /* Goes in read_status_mask for break detection as the HW doesn't do it*/
151 #define CDNS_UART_IXR_BRK 0x00002000
152
153 #define CDNS_UART_RXBS_SUPPORT BIT(1)
154 /*
155 * Modem Control register:
156 * The read/write Modem Control register controls the interface with the modem
157 * or data set, or a peripheral device emulating a modem.
158 */
159 #define CDNS_UART_MODEMCR_FCM 0x00000020 /* Automatic flow control mode */
160 #define CDNS_UART_MODEMCR_RTS 0x00000002 /* Request to send output control */
161 #define CDNS_UART_MODEMCR_DTR 0x00000001 /* Data Terminal Ready */
162
163 /*
164 * Channel Status Register:
165 * The channel status register (CSR) is provided to enable the control logic
166 * to monitor the status of bits in the channel interrupt status register,
167 * even if these are masked out by the interrupt mask register.
168 */
169 #define CDNS_UART_SR_RXEMPTY 0x00000002 /* RX FIFO empty */
170 #define CDNS_UART_SR_TXEMPTY 0x00000008 /* TX FIFO empty */
171 #define CDNS_UART_SR_TXFULL 0x00000010 /* TX FIFO full */
172 #define CDNS_UART_SR_RXTRIG 0x00000001 /* Rx Trigger */
173
174 /* baud dividers min/max values */
175 #define CDNS_UART_BDIV_MIN 4
176 #define CDNS_UART_BDIV_MAX 255
177 #define CDNS_UART_CD_MAX 65535
178
179 /**
180 * struct cdns_uart - device data
181 * @port: Pointer to the UART port
182 * @uartclk: Reference clock
183 * @pclk: APB clock
184 * @baud: Current baud rate
185 * @clk_rate_change_nb: Notifier block for clock changes
186 */
187 struct cdns_uart {
188 struct uart_port *port;
189 struct clk *uartclk;
190 struct clk *pclk;
191 unsigned int baud;
192 struct notifier_block clk_rate_change_nb;
193 u32 quirks;
194 };
195 struct cdns_platform_data {
196 u32 quirks;
197 };
198 #define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
199 clk_rate_change_nb);
200
201 /**
202 * cdns_uart_handle_rx - Handle the received bytes along with Rx errors.
203 * @dev_id: Id of the UART port
204 * @isrstatus: The interrupt status register value as read
205 * Return: None
206 */
cdns_uart_handle_rx(void * dev_id,unsigned int isrstatus)207 static void cdns_uart_handle_rx(void *dev_id, unsigned int isrstatus)
208 {
209 struct uart_port *port = (struct uart_port *)dev_id;
210 struct cdns_uart *cdns_uart = port->private_data;
211 unsigned int data;
212 unsigned int rxbs_status = 0;
213 unsigned int status_mask;
214 unsigned int framerrprocessed = 0;
215 char status = TTY_NORMAL;
216 bool is_rxbs_support;
217
218 is_rxbs_support = cdns_uart->quirks & CDNS_UART_RXBS_SUPPORT;
219
220 while ((readl(port->membase + CDNS_UART_SR) &
221 CDNS_UART_SR_RXEMPTY) != CDNS_UART_SR_RXEMPTY) {
222 if (is_rxbs_support)
223 rxbs_status = readl(port->membase + CDNS_UART_RXBS);
224 data = readl(port->membase + CDNS_UART_FIFO);
225 port->icount.rx++;
226 /*
227 * There is no hardware break detection in Zynq, so we interpret
228 * framing error with all-zeros data as a break sequence.
229 * Most of the time, there's another non-zero byte at the
230 * end of the sequence.
231 */
232 if (!is_rxbs_support && (isrstatus & CDNS_UART_IXR_FRAMING)) {
233 if (!data) {
234 port->read_status_mask |= CDNS_UART_IXR_BRK;
235 framerrprocessed = 1;
236 continue;
237 }
238 }
239 if (is_rxbs_support && (rxbs_status & CDNS_UART_RXBS_BRK)) {
240 port->icount.brk++;
241 status = TTY_BREAK;
242 if (uart_handle_break(port))
243 continue;
244 }
245
246 isrstatus &= port->read_status_mask;
247 isrstatus &= ~port->ignore_status_mask;
248 status_mask = port->read_status_mask;
249 status_mask &= ~port->ignore_status_mask;
250
251 if (data &&
252 (port->read_status_mask & CDNS_UART_IXR_BRK)) {
253 port->read_status_mask &= ~CDNS_UART_IXR_BRK;
254 port->icount.brk++;
255 if (uart_handle_break(port))
256 continue;
257 }
258
259 if (uart_handle_sysrq_char(port, data))
260 continue;
261
262 if (is_rxbs_support) {
263 if ((rxbs_status & CDNS_UART_RXBS_PARITY)
264 && (status_mask & CDNS_UART_IXR_PARITY)) {
265 port->icount.parity++;
266 status = TTY_PARITY;
267 }
268 if ((rxbs_status & CDNS_UART_RXBS_FRAMING)
269 && (status_mask & CDNS_UART_IXR_PARITY)) {
270 port->icount.frame++;
271 status = TTY_FRAME;
272 }
273 } else {
274 if (isrstatus & CDNS_UART_IXR_PARITY) {
275 port->icount.parity++;
276 status = TTY_PARITY;
277 }
278 if ((isrstatus & CDNS_UART_IXR_FRAMING) &&
279 !framerrprocessed) {
280 port->icount.frame++;
281 status = TTY_FRAME;
282 }
283 }
284 if (isrstatus & CDNS_UART_IXR_OVERRUN) {
285 port->icount.overrun++;
286 tty_insert_flip_char(&port->state->port, 0,
287 TTY_OVERRUN);
288 }
289 tty_insert_flip_char(&port->state->port, data, status);
290 isrstatus = 0;
291 }
292 spin_unlock(&port->lock);
293 tty_flip_buffer_push(&port->state->port);
294 spin_lock(&port->lock);
295 }
296
297 /**
298 * cdns_uart_handle_tx - Handle the bytes to be Txed.
299 * @dev_id: Id of the UART port
300 * Return: None
301 */
cdns_uart_handle_tx(void * dev_id)302 static void cdns_uart_handle_tx(void *dev_id)
303 {
304 struct uart_port *port = (struct uart_port *)dev_id;
305 unsigned int numbytes;
306
307 if (uart_circ_empty(&port->state->xmit)) {
308 writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IDR);
309 } else {
310 numbytes = port->fifosize;
311 while (numbytes && !uart_circ_empty(&port->state->xmit) &&
312 !(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXFULL)) {
313 /*
314 * Get the data from the UART circular buffer
315 * and write it to the cdns_uart's TX_FIFO
316 * register.
317 */
318 writel(
319 port->state->xmit.buf[port->state->xmit.
320 tail], port->membase + CDNS_UART_FIFO);
321
322 port->icount.tx++;
323
324 /*
325 * Adjust the tail of the UART buffer and wrap
326 * the buffer if it reaches limit.
327 */
328 port->state->xmit.tail =
329 (port->state->xmit.tail + 1) &
330 (UART_XMIT_SIZE - 1);
331
332 numbytes--;
333 }
334
335 if (uart_circ_chars_pending(
336 &port->state->xmit) < WAKEUP_CHARS)
337 uart_write_wakeup(port);
338 }
339 }
340
341 /**
342 * cdns_uart_isr - Interrupt handler
343 * @irq: Irq number
344 * @dev_id: Id of the port
345 *
346 * Return: IRQHANDLED
347 */
cdns_uart_isr(int irq,void * dev_id)348 static irqreturn_t cdns_uart_isr(int irq, void *dev_id)
349 {
350 struct uart_port *port = (struct uart_port *)dev_id;
351 unsigned int isrstatus;
352
353 spin_lock(&port->lock);
354
355 /* Read the interrupt status register to determine which
356 * interrupt(s) is/are active and clear them.
357 */
358 isrstatus = readl(port->membase + CDNS_UART_ISR);
359 writel(isrstatus, port->membase + CDNS_UART_ISR);
360
361 if (isrstatus & CDNS_UART_IXR_TXEMPTY) {
362 cdns_uart_handle_tx(dev_id);
363 isrstatus &= ~CDNS_UART_IXR_TXEMPTY;
364 }
365 if (isrstatus & CDNS_UART_IXR_MASK)
366 cdns_uart_handle_rx(dev_id, isrstatus);
367
368 spin_unlock(&port->lock);
369 return IRQ_HANDLED;
370 }
371
372 /**
373 * cdns_uart_calc_baud_divs - Calculate baud rate divisors
374 * @clk: UART module input clock
375 * @baud: Desired baud rate
376 * @rbdiv: BDIV value (return value)
377 * @rcd: CD value (return value)
378 * @div8: Value for clk_sel bit in mod (return value)
379 * Return: baud rate, requested baud when possible, or actual baud when there
380 * was too much error, zero if no valid divisors are found.
381 *
382 * Formula to obtain baud rate is
383 * baud_tx/rx rate = clk/CD * (BDIV + 1)
384 * input_clk = (Uart User Defined Clock or Apb Clock)
385 * depends on UCLKEN in MR Reg
386 * clk = input_clk or input_clk/8;
387 * depends on CLKS in MR reg
388 * CD and BDIV depends on values in
389 * baud rate generate register
390 * baud rate clock divisor register
391 */
cdns_uart_calc_baud_divs(unsigned int clk,unsigned int baud,u32 * rbdiv,u32 * rcd,int * div8)392 static unsigned int cdns_uart_calc_baud_divs(unsigned int clk,
393 unsigned int baud, u32 *rbdiv, u32 *rcd, int *div8)
394 {
395 u32 cd, bdiv;
396 unsigned int calc_baud;
397 unsigned int bestbaud = 0;
398 unsigned int bauderror;
399 unsigned int besterror = ~0;
400
401 if (baud < clk / ((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX)) {
402 *div8 = 1;
403 clk /= 8;
404 } else {
405 *div8 = 0;
406 }
407
408 for (bdiv = CDNS_UART_BDIV_MIN; bdiv <= CDNS_UART_BDIV_MAX; bdiv++) {
409 cd = DIV_ROUND_CLOSEST(clk, baud * (bdiv + 1));
410 if (cd < 1 || cd > CDNS_UART_CD_MAX)
411 continue;
412
413 calc_baud = clk / (cd * (bdiv + 1));
414
415 if (baud > calc_baud)
416 bauderror = baud - calc_baud;
417 else
418 bauderror = calc_baud - baud;
419
420 if (besterror > bauderror) {
421 *rbdiv = bdiv;
422 *rcd = cd;
423 bestbaud = calc_baud;
424 besterror = bauderror;
425 }
426 }
427 /* use the values when percent error is acceptable */
428 if (((besterror * 100) / baud) < 3)
429 bestbaud = baud;
430
431 return bestbaud;
432 }
433
434 /**
435 * cdns_uart_set_baud_rate - Calculate and set the baud rate
436 * @port: Handle to the uart port structure
437 * @baud: Baud rate to set
438 * Return: baud rate, requested baud when possible, or actual baud when there
439 * was too much error, zero if no valid divisors are found.
440 */
cdns_uart_set_baud_rate(struct uart_port * port,unsigned int baud)441 static unsigned int cdns_uart_set_baud_rate(struct uart_port *port,
442 unsigned int baud)
443 {
444 unsigned int calc_baud;
445 u32 cd = 0, bdiv = 0;
446 u32 mreg;
447 int div8;
448 struct cdns_uart *cdns_uart = port->private_data;
449
450 calc_baud = cdns_uart_calc_baud_divs(port->uartclk, baud, &bdiv, &cd,
451 &div8);
452
453 /* Write new divisors to hardware */
454 mreg = readl(port->membase + CDNS_UART_MR);
455 if (div8)
456 mreg |= CDNS_UART_MR_CLKSEL;
457 else
458 mreg &= ~CDNS_UART_MR_CLKSEL;
459 writel(mreg, port->membase + CDNS_UART_MR);
460 writel(cd, port->membase + CDNS_UART_BAUDGEN);
461 writel(bdiv, port->membase + CDNS_UART_BAUDDIV);
462 cdns_uart->baud = baud;
463
464 return calc_baud;
465 }
466
467 #ifdef CONFIG_COMMON_CLK
468 /**
469 * cdns_uart_clk_notitifer_cb - Clock notifier callback
470 * @nb: Notifier block
471 * @event: Notify event
472 * @data: Notifier data
473 * Return: NOTIFY_OK or NOTIFY_DONE on success, NOTIFY_BAD on error.
474 */
cdns_uart_clk_notifier_cb(struct notifier_block * nb,unsigned long event,void * data)475 static int cdns_uart_clk_notifier_cb(struct notifier_block *nb,
476 unsigned long event, void *data)
477 {
478 u32 ctrl_reg;
479 struct uart_port *port;
480 int locked = 0;
481 struct clk_notifier_data *ndata = data;
482 unsigned long flags = 0;
483 struct cdns_uart *cdns_uart = to_cdns_uart(nb);
484
485 port = cdns_uart->port;
486 if (port->suspended)
487 return NOTIFY_OK;
488
489 switch (event) {
490 case PRE_RATE_CHANGE:
491 {
492 u32 bdiv, cd;
493 int div8;
494
495 /*
496 * Find out if current baud-rate can be achieved with new clock
497 * frequency.
498 */
499 if (!cdns_uart_calc_baud_divs(ndata->new_rate, cdns_uart->baud,
500 &bdiv, &cd, &div8)) {
501 dev_warn(port->dev, "clock rate change rejected\n");
502 return NOTIFY_BAD;
503 }
504
505 spin_lock_irqsave(&cdns_uart->port->lock, flags);
506
507 /* Disable the TX and RX to set baud rate */
508 ctrl_reg = readl(port->membase + CDNS_UART_CR);
509 ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
510 writel(ctrl_reg, port->membase + CDNS_UART_CR);
511
512 spin_unlock_irqrestore(&cdns_uart->port->lock, flags);
513
514 return NOTIFY_OK;
515 }
516 case POST_RATE_CHANGE:
517 /*
518 * Set clk dividers to generate correct baud with new clock
519 * frequency.
520 */
521
522 spin_lock_irqsave(&cdns_uart->port->lock, flags);
523
524 locked = 1;
525 port->uartclk = ndata->new_rate;
526
527 cdns_uart->baud = cdns_uart_set_baud_rate(cdns_uart->port,
528 cdns_uart->baud);
529 /* fall through */
530 case ABORT_RATE_CHANGE:
531 if (!locked)
532 spin_lock_irqsave(&cdns_uart->port->lock, flags);
533
534 /* Set TX/RX Reset */
535 ctrl_reg = readl(port->membase + CDNS_UART_CR);
536 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
537 writel(ctrl_reg, port->membase + CDNS_UART_CR);
538
539 while (readl(port->membase + CDNS_UART_CR) &
540 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
541 cpu_relax();
542
543 /*
544 * Clear the RX disable and TX disable bits and then set the TX
545 * enable bit and RX enable bit to enable the transmitter and
546 * receiver.
547 */
548 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
549 ctrl_reg = readl(port->membase + CDNS_UART_CR);
550 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
551 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
552 writel(ctrl_reg, port->membase + CDNS_UART_CR);
553
554 spin_unlock_irqrestore(&cdns_uart->port->lock, flags);
555
556 return NOTIFY_OK;
557 default:
558 return NOTIFY_DONE;
559 }
560 }
561 #endif
562
563 /**
564 * cdns_uart_start_tx - Start transmitting bytes
565 * @port: Handle to the uart port structure
566 */
cdns_uart_start_tx(struct uart_port * port)567 static void cdns_uart_start_tx(struct uart_port *port)
568 {
569 unsigned int status;
570
571 if (uart_tx_stopped(port))
572 return;
573
574 /*
575 * Set the TX enable bit and clear the TX disable bit to enable the
576 * transmitter.
577 */
578 status = readl(port->membase + CDNS_UART_CR);
579 status &= ~CDNS_UART_CR_TX_DIS;
580 status |= CDNS_UART_CR_TX_EN;
581 writel(status, port->membase + CDNS_UART_CR);
582
583 if (uart_circ_empty(&port->state->xmit))
584 return;
585
586 cdns_uart_handle_tx(port);
587
588 writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_ISR);
589 /* Enable the TX Empty interrupt */
590 writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IER);
591 }
592
593 /**
594 * cdns_uart_stop_tx - Stop TX
595 * @port: Handle to the uart port structure
596 */
cdns_uart_stop_tx(struct uart_port * port)597 static void cdns_uart_stop_tx(struct uart_port *port)
598 {
599 unsigned int regval;
600
601 regval = readl(port->membase + CDNS_UART_CR);
602 regval |= CDNS_UART_CR_TX_DIS;
603 /* Disable the transmitter */
604 writel(regval, port->membase + CDNS_UART_CR);
605 }
606
607 /**
608 * cdns_uart_stop_rx - Stop RX
609 * @port: Handle to the uart port structure
610 */
cdns_uart_stop_rx(struct uart_port * port)611 static void cdns_uart_stop_rx(struct uart_port *port)
612 {
613 unsigned int regval;
614
615 /* Disable RX IRQs */
616 writel(CDNS_UART_RX_IRQS, port->membase + CDNS_UART_IDR);
617
618 /* Disable the receiver */
619 regval = readl(port->membase + CDNS_UART_CR);
620 regval |= CDNS_UART_CR_RX_DIS;
621 writel(regval, port->membase + CDNS_UART_CR);
622 }
623
624 /**
625 * cdns_uart_tx_empty - Check whether TX is empty
626 * @port: Handle to the uart port structure
627 *
628 * Return: TIOCSER_TEMT on success, 0 otherwise
629 */
cdns_uart_tx_empty(struct uart_port * port)630 static unsigned int cdns_uart_tx_empty(struct uart_port *port)
631 {
632 unsigned int status;
633
634 status = readl(port->membase + CDNS_UART_SR) &
635 CDNS_UART_SR_TXEMPTY;
636 return status ? TIOCSER_TEMT : 0;
637 }
638
639 /**
640 * cdns_uart_break_ctl - Based on the input ctl we have to start or stop
641 * transmitting char breaks
642 * @port: Handle to the uart port structure
643 * @ctl: Value based on which start or stop decision is taken
644 */
cdns_uart_break_ctl(struct uart_port * port,int ctl)645 static void cdns_uart_break_ctl(struct uart_port *port, int ctl)
646 {
647 unsigned int status;
648 unsigned long flags;
649
650 spin_lock_irqsave(&port->lock, flags);
651
652 status = readl(port->membase + CDNS_UART_CR);
653
654 if (ctl == -1)
655 writel(CDNS_UART_CR_STARTBRK | status,
656 port->membase + CDNS_UART_CR);
657 else {
658 if ((status & CDNS_UART_CR_STOPBRK) == 0)
659 writel(CDNS_UART_CR_STOPBRK | status,
660 port->membase + CDNS_UART_CR);
661 }
662 spin_unlock_irqrestore(&port->lock, flags);
663 }
664
665 /**
666 * cdns_uart_set_termios - termios operations, handling data length, parity,
667 * stop bits, flow control, baud rate
668 * @port: Handle to the uart port structure
669 * @termios: Handle to the input termios structure
670 * @old: Values of the previously saved termios structure
671 */
cdns_uart_set_termios(struct uart_port * port,struct ktermios * termios,struct ktermios * old)672 static void cdns_uart_set_termios(struct uart_port *port,
673 struct ktermios *termios, struct ktermios *old)
674 {
675 unsigned int cval = 0;
676 unsigned int baud, minbaud, maxbaud;
677 unsigned long flags;
678 unsigned int ctrl_reg, mode_reg;
679
680 spin_lock_irqsave(&port->lock, flags);
681
682 /* Wait for the transmit FIFO to empty before making changes */
683 if (!(readl(port->membase + CDNS_UART_CR) &
684 CDNS_UART_CR_TX_DIS)) {
685 while (!(readl(port->membase + CDNS_UART_SR) &
686 CDNS_UART_SR_TXEMPTY)) {
687 cpu_relax();
688 }
689 }
690
691 /* Disable the TX and RX to set baud rate */
692 ctrl_reg = readl(port->membase + CDNS_UART_CR);
693 ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
694 writel(ctrl_reg, port->membase + CDNS_UART_CR);
695
696 /*
697 * Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk
698 * min and max baud should be calculated here based on port->uartclk.
699 * this way we get a valid baud and can safely call set_baud()
700 */
701 minbaud = port->uartclk /
702 ((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX * 8);
703 maxbaud = port->uartclk / (CDNS_UART_BDIV_MIN + 1);
704 baud = uart_get_baud_rate(port, termios, old, minbaud, maxbaud);
705 baud = cdns_uart_set_baud_rate(port, baud);
706 if (tty_termios_baud_rate(termios))
707 tty_termios_encode_baud_rate(termios, baud, baud);
708
709 /* Update the per-port timeout. */
710 uart_update_timeout(port, termios->c_cflag, baud);
711
712 /* Set TX/RX Reset */
713 ctrl_reg = readl(port->membase + CDNS_UART_CR);
714 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
715 writel(ctrl_reg, port->membase + CDNS_UART_CR);
716
717 while (readl(port->membase + CDNS_UART_CR) &
718 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
719 cpu_relax();
720
721 /*
722 * Clear the RX disable and TX disable bits and then set the TX enable
723 * bit and RX enable bit to enable the transmitter and receiver.
724 */
725 ctrl_reg = readl(port->membase + CDNS_UART_CR);
726 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
727 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
728 writel(ctrl_reg, port->membase + CDNS_UART_CR);
729
730 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
731
732 port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
733 CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
734 port->ignore_status_mask = 0;
735
736 if (termios->c_iflag & INPCK)
737 port->read_status_mask |= CDNS_UART_IXR_PARITY |
738 CDNS_UART_IXR_FRAMING;
739
740 if (termios->c_iflag & IGNPAR)
741 port->ignore_status_mask |= CDNS_UART_IXR_PARITY |
742 CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
743
744 /* ignore all characters if CREAD is not set */
745 if ((termios->c_cflag & CREAD) == 0)
746 port->ignore_status_mask |= CDNS_UART_IXR_RXTRIG |
747 CDNS_UART_IXR_TOUT | CDNS_UART_IXR_PARITY |
748 CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
749
750 mode_reg = readl(port->membase + CDNS_UART_MR);
751
752 /* Handling Data Size */
753 switch (termios->c_cflag & CSIZE) {
754 case CS6:
755 cval |= CDNS_UART_MR_CHARLEN_6_BIT;
756 break;
757 case CS7:
758 cval |= CDNS_UART_MR_CHARLEN_7_BIT;
759 break;
760 default:
761 case CS8:
762 cval |= CDNS_UART_MR_CHARLEN_8_BIT;
763 termios->c_cflag &= ~CSIZE;
764 termios->c_cflag |= CS8;
765 break;
766 }
767
768 /* Handling Parity and Stop Bits length */
769 if (termios->c_cflag & CSTOPB)
770 cval |= CDNS_UART_MR_STOPMODE_2_BIT; /* 2 STOP bits */
771 else
772 cval |= CDNS_UART_MR_STOPMODE_1_BIT; /* 1 STOP bit */
773
774 if (termios->c_cflag & PARENB) {
775 /* Mark or Space parity */
776 if (termios->c_cflag & CMSPAR) {
777 if (termios->c_cflag & PARODD)
778 cval |= CDNS_UART_MR_PARITY_MARK;
779 else
780 cval |= CDNS_UART_MR_PARITY_SPACE;
781 } else {
782 if (termios->c_cflag & PARODD)
783 cval |= CDNS_UART_MR_PARITY_ODD;
784 else
785 cval |= CDNS_UART_MR_PARITY_EVEN;
786 }
787 } else {
788 cval |= CDNS_UART_MR_PARITY_NONE;
789 }
790 cval |= mode_reg & 1;
791 writel(cval, port->membase + CDNS_UART_MR);
792
793 spin_unlock_irqrestore(&port->lock, flags);
794 }
795
796 /**
797 * cdns_uart_startup - Called when an application opens a cdns_uart port
798 * @port: Handle to the uart port structure
799 *
800 * Return: 0 on success, negative errno otherwise
801 */
cdns_uart_startup(struct uart_port * port)802 static int cdns_uart_startup(struct uart_port *port)
803 {
804 struct cdns_uart *cdns_uart = port->private_data;
805 bool is_brk_support;
806 int ret;
807 unsigned long flags;
808 unsigned int status = 0;
809
810 is_brk_support = cdns_uart->quirks & CDNS_UART_RXBS_SUPPORT;
811
812 spin_lock_irqsave(&port->lock, flags);
813
814 /* Disable the TX and RX */
815 writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS,
816 port->membase + CDNS_UART_CR);
817
818 /* Set the Control Register with TX/RX Enable, TX/RX Reset,
819 * no break chars.
820 */
821 writel(CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST,
822 port->membase + CDNS_UART_CR);
823
824 while (readl(port->membase + CDNS_UART_CR) &
825 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
826 cpu_relax();
827
828 /*
829 * Clear the RX disable bit and then set the RX enable bit to enable
830 * the receiver.
831 */
832 status = readl(port->membase + CDNS_UART_CR);
833 status &= CDNS_UART_CR_RX_DIS;
834 status |= CDNS_UART_CR_RX_EN;
835 writel(status, port->membase + CDNS_UART_CR);
836
837 /* Set the Mode Register with normal mode,8 data bits,1 stop bit,
838 * no parity.
839 */
840 writel(CDNS_UART_MR_CHMODE_NORM | CDNS_UART_MR_STOPMODE_1_BIT
841 | CDNS_UART_MR_PARITY_NONE | CDNS_UART_MR_CHARLEN_8_BIT,
842 port->membase + CDNS_UART_MR);
843
844 /*
845 * Set the RX FIFO Trigger level to use most of the FIFO, but it
846 * can be tuned with a module parameter
847 */
848 writel(rx_trigger_level, port->membase + CDNS_UART_RXWM);
849
850 /*
851 * Receive Timeout register is enabled but it
852 * can be tuned with a module parameter
853 */
854 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
855
856 /* Clear out any pending interrupts before enabling them */
857 writel(readl(port->membase + CDNS_UART_ISR),
858 port->membase + CDNS_UART_ISR);
859
860 spin_unlock_irqrestore(&port->lock, flags);
861
862 ret = request_irq(port->irq, cdns_uart_isr, 0, CDNS_UART_NAME, port);
863 if (ret) {
864 dev_err(port->dev, "request_irq '%d' failed with %d\n",
865 port->irq, ret);
866 return ret;
867 }
868
869 /* Set the Interrupt Registers with desired interrupts */
870 if (is_brk_support)
871 writel(CDNS_UART_RX_IRQS | CDNS_UART_IXR_BRK,
872 port->membase + CDNS_UART_IER);
873 else
874 writel(CDNS_UART_RX_IRQS, port->membase + CDNS_UART_IER);
875
876 return 0;
877 }
878
879 /**
880 * cdns_uart_shutdown - Called when an application closes a cdns_uart port
881 * @port: Handle to the uart port structure
882 */
cdns_uart_shutdown(struct uart_port * port)883 static void cdns_uart_shutdown(struct uart_port *port)
884 {
885 int status;
886 unsigned long flags;
887
888 spin_lock_irqsave(&port->lock, flags);
889
890 /* Disable interrupts */
891 status = readl(port->membase + CDNS_UART_IMR);
892 writel(status, port->membase + CDNS_UART_IDR);
893 writel(0xffffffff, port->membase + CDNS_UART_ISR);
894
895 /* Disable the TX and RX */
896 writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS,
897 port->membase + CDNS_UART_CR);
898
899 spin_unlock_irqrestore(&port->lock, flags);
900
901 free_irq(port->irq, port);
902 }
903
904 /**
905 * cdns_uart_type - Set UART type to cdns_uart port
906 * @port: Handle to the uart port structure
907 *
908 * Return: string on success, NULL otherwise
909 */
cdns_uart_type(struct uart_port * port)910 static const char *cdns_uart_type(struct uart_port *port)
911 {
912 return port->type == PORT_XUARTPS ? CDNS_UART_NAME : NULL;
913 }
914
915 /**
916 * cdns_uart_verify_port - Verify the port params
917 * @port: Handle to the uart port structure
918 * @ser: Handle to the structure whose members are compared
919 *
920 * Return: 0 on success, negative errno otherwise.
921 */
cdns_uart_verify_port(struct uart_port * port,struct serial_struct * ser)922 static int cdns_uart_verify_port(struct uart_port *port,
923 struct serial_struct *ser)
924 {
925 if (ser->type != PORT_UNKNOWN && ser->type != PORT_XUARTPS)
926 return -EINVAL;
927 if (port->irq != ser->irq)
928 return -EINVAL;
929 if (ser->io_type != UPIO_MEM)
930 return -EINVAL;
931 if (port->iobase != ser->port)
932 return -EINVAL;
933 if (ser->hub6 != 0)
934 return -EINVAL;
935 return 0;
936 }
937
938 /**
939 * cdns_uart_request_port - Claim the memory region attached to cdns_uart port,
940 * called when the driver adds a cdns_uart port via
941 * uart_add_one_port()
942 * @port: Handle to the uart port structure
943 *
944 * Return: 0 on success, negative errno otherwise.
945 */
cdns_uart_request_port(struct uart_port * port)946 static int cdns_uart_request_port(struct uart_port *port)
947 {
948 if (!request_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE,
949 CDNS_UART_NAME)) {
950 return -ENOMEM;
951 }
952
953 port->membase = ioremap(port->mapbase, CDNS_UART_REGISTER_SPACE);
954 if (!port->membase) {
955 dev_err(port->dev, "Unable to map registers\n");
956 release_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE);
957 return -ENOMEM;
958 }
959 return 0;
960 }
961
962 /**
963 * cdns_uart_release_port - Release UART port
964 * @port: Handle to the uart port structure
965 *
966 * Release the memory region attached to a cdns_uart port. Called when the
967 * driver removes a cdns_uart port via uart_remove_one_port().
968 */
cdns_uart_release_port(struct uart_port * port)969 static void cdns_uart_release_port(struct uart_port *port)
970 {
971 release_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE);
972 iounmap(port->membase);
973 port->membase = NULL;
974 }
975
976 /**
977 * cdns_uart_config_port - Configure UART port
978 * @port: Handle to the uart port structure
979 * @flags: If any
980 */
cdns_uart_config_port(struct uart_port * port,int flags)981 static void cdns_uart_config_port(struct uart_port *port, int flags)
982 {
983 if (flags & UART_CONFIG_TYPE && cdns_uart_request_port(port) == 0)
984 port->type = PORT_XUARTPS;
985 }
986
987 /**
988 * cdns_uart_get_mctrl - Get the modem control state
989 * @port: Handle to the uart port structure
990 *
991 * Return: the modem control state
992 */
cdns_uart_get_mctrl(struct uart_port * port)993 static unsigned int cdns_uart_get_mctrl(struct uart_port *port)
994 {
995 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
996 }
997
cdns_uart_set_mctrl(struct uart_port * port,unsigned int mctrl)998 static void cdns_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
999 {
1000 u32 val;
1001
1002 val = readl(port->membase + CDNS_UART_MODEMCR);
1003
1004 val &= ~(CDNS_UART_MODEMCR_RTS | CDNS_UART_MODEMCR_DTR);
1005
1006 if (mctrl & TIOCM_RTS)
1007 val |= CDNS_UART_MODEMCR_RTS;
1008 if (mctrl & TIOCM_DTR)
1009 val |= CDNS_UART_MODEMCR_DTR;
1010
1011 writel(val, port->membase + CDNS_UART_MODEMCR);
1012 }
1013
1014 #ifdef CONFIG_CONSOLE_POLL
cdns_uart_poll_get_char(struct uart_port * port)1015 static int cdns_uart_poll_get_char(struct uart_port *port)
1016 {
1017 int c;
1018 unsigned long flags;
1019
1020 spin_lock_irqsave(&port->lock, flags);
1021
1022 /* Check if FIFO is empty */
1023 if (readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_RXEMPTY)
1024 c = NO_POLL_CHAR;
1025 else /* Read a character */
1026 c = (unsigned char) readl(port->membase + CDNS_UART_FIFO);
1027
1028 spin_unlock_irqrestore(&port->lock, flags);
1029
1030 return c;
1031 }
1032
cdns_uart_poll_put_char(struct uart_port * port,unsigned char c)1033 static void cdns_uart_poll_put_char(struct uart_port *port, unsigned char c)
1034 {
1035 unsigned long flags;
1036
1037 spin_lock_irqsave(&port->lock, flags);
1038
1039 /* Wait until FIFO is empty */
1040 while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY))
1041 cpu_relax();
1042
1043 /* Write a character */
1044 writel(c, port->membase + CDNS_UART_FIFO);
1045
1046 /* Wait until FIFO is empty */
1047 while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY))
1048 cpu_relax();
1049
1050 spin_unlock_irqrestore(&port->lock, flags);
1051
1052 return;
1053 }
1054 #endif
1055
cdns_uart_pm(struct uart_port * port,unsigned int state,unsigned int oldstate)1056 static void cdns_uart_pm(struct uart_port *port, unsigned int state,
1057 unsigned int oldstate)
1058 {
1059 struct cdns_uart *cdns_uart = port->private_data;
1060
1061 switch (state) {
1062 case UART_PM_STATE_OFF:
1063 clk_disable(cdns_uart->uartclk);
1064 clk_disable(cdns_uart->pclk);
1065 break;
1066 default:
1067 clk_enable(cdns_uart->pclk);
1068 clk_enable(cdns_uart->uartclk);
1069 break;
1070 }
1071 }
1072
1073 static const struct uart_ops cdns_uart_ops = {
1074 .set_mctrl = cdns_uart_set_mctrl,
1075 .get_mctrl = cdns_uart_get_mctrl,
1076 .start_tx = cdns_uart_start_tx,
1077 .stop_tx = cdns_uart_stop_tx,
1078 .stop_rx = cdns_uart_stop_rx,
1079 .tx_empty = cdns_uart_tx_empty,
1080 .break_ctl = cdns_uart_break_ctl,
1081 .set_termios = cdns_uart_set_termios,
1082 .startup = cdns_uart_startup,
1083 .shutdown = cdns_uart_shutdown,
1084 .pm = cdns_uart_pm,
1085 .type = cdns_uart_type,
1086 .verify_port = cdns_uart_verify_port,
1087 .request_port = cdns_uart_request_port,
1088 .release_port = cdns_uart_release_port,
1089 .config_port = cdns_uart_config_port,
1090 #ifdef CONFIG_CONSOLE_POLL
1091 .poll_get_char = cdns_uart_poll_get_char,
1092 .poll_put_char = cdns_uart_poll_put_char,
1093 #endif
1094 };
1095
1096 static struct uart_port cdns_uart_port[CDNS_UART_NR_PORTS];
1097
1098 /**
1099 * cdns_uart_get_port - Configure the port from platform device resource info
1100 * @id: Port id
1101 *
1102 * Return: a pointer to a uart_port or NULL for failure
1103 */
cdns_uart_get_port(int id)1104 static struct uart_port *cdns_uart_get_port(int id)
1105 {
1106 struct uart_port *port;
1107
1108 /* Try the given port id if failed use default method */
1109 if (cdns_uart_port[id].mapbase != 0) {
1110 /* Find the next unused port */
1111 for (id = 0; id < CDNS_UART_NR_PORTS; id++)
1112 if (cdns_uart_port[id].mapbase == 0)
1113 break;
1114 }
1115
1116 if (id >= CDNS_UART_NR_PORTS)
1117 return NULL;
1118
1119 port = &cdns_uart_port[id];
1120
1121 /* At this point, we've got an empty uart_port struct, initialize it */
1122 spin_lock_init(&port->lock);
1123 port->membase = NULL;
1124 port->irq = 0;
1125 port->type = PORT_UNKNOWN;
1126 port->iotype = UPIO_MEM32;
1127 port->flags = UPF_BOOT_AUTOCONF;
1128 port->ops = &cdns_uart_ops;
1129 port->fifosize = CDNS_UART_FIFO_SIZE;
1130 port->line = id;
1131 port->dev = NULL;
1132 return port;
1133 }
1134
1135 #ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1136 /**
1137 * cdns_uart_console_wait_tx - Wait for the TX to be full
1138 * @port: Handle to the uart port structure
1139 */
cdns_uart_console_wait_tx(struct uart_port * port)1140 static void cdns_uart_console_wait_tx(struct uart_port *port)
1141 {
1142 while (!(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXEMPTY))
1143 barrier();
1144 }
1145
1146 /**
1147 * cdns_uart_console_putchar - write the character to the FIFO buffer
1148 * @port: Handle to the uart port structure
1149 * @ch: Character to be written
1150 */
cdns_uart_console_putchar(struct uart_port * port,int ch)1151 static void cdns_uart_console_putchar(struct uart_port *port, int ch)
1152 {
1153 cdns_uart_console_wait_tx(port);
1154 writel(ch, port->membase + CDNS_UART_FIFO);
1155 }
1156
cdns_early_write(struct console * con,const char * s,unsigned n)1157 static void __init cdns_early_write(struct console *con, const char *s,
1158 unsigned n)
1159 {
1160 struct earlycon_device *dev = con->data;
1161
1162 uart_console_write(&dev->port, s, n, cdns_uart_console_putchar);
1163 }
1164
cdns_early_console_setup(struct earlycon_device * device,const char * opt)1165 static int __init cdns_early_console_setup(struct earlycon_device *device,
1166 const char *opt)
1167 {
1168 struct uart_port *port = &device->port;
1169
1170 if (!port->membase)
1171 return -ENODEV;
1172
1173 /* initialise control register */
1174 writel(CDNS_UART_CR_TX_EN|CDNS_UART_CR_TXRST|CDNS_UART_CR_RXRST,
1175 port->membase + CDNS_UART_CR);
1176
1177 /* only set baud if specified on command line - otherwise
1178 * assume it has been initialized by a boot loader.
1179 */
1180 if (device->baud) {
1181 u32 cd = 0, bdiv = 0;
1182 u32 mr;
1183 int div8;
1184
1185 cdns_uart_calc_baud_divs(port->uartclk, device->baud,
1186 &bdiv, &cd, &div8);
1187 mr = CDNS_UART_MR_PARITY_NONE;
1188 if (div8)
1189 mr |= CDNS_UART_MR_CLKSEL;
1190
1191 writel(mr, port->membase + CDNS_UART_MR);
1192 writel(cd, port->membase + CDNS_UART_BAUDGEN);
1193 writel(bdiv, port->membase + CDNS_UART_BAUDDIV);
1194 }
1195
1196 device->con->write = cdns_early_write;
1197
1198 return 0;
1199 }
1200 OF_EARLYCON_DECLARE(cdns, "xlnx,xuartps", cdns_early_console_setup);
1201 OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p8", cdns_early_console_setup);
1202 OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p12", cdns_early_console_setup);
1203 OF_EARLYCON_DECLARE(cdns, "xlnx,zynqmp-uart", cdns_early_console_setup);
1204
1205 /**
1206 * cdns_uart_console_write - perform write operation
1207 * @co: Console handle
1208 * @s: Pointer to character array
1209 * @count: No of characters
1210 */
cdns_uart_console_write(struct console * co,const char * s,unsigned int count)1211 static void cdns_uart_console_write(struct console *co, const char *s,
1212 unsigned int count)
1213 {
1214 struct uart_port *port = &cdns_uart_port[co->index];
1215 unsigned long flags;
1216 unsigned int imr, ctrl;
1217 int locked = 1;
1218
1219 if (port->sysrq)
1220 locked = 0;
1221 else if (oops_in_progress)
1222 locked = spin_trylock_irqsave(&port->lock, flags);
1223 else
1224 spin_lock_irqsave(&port->lock, flags);
1225
1226 /* save and disable interrupt */
1227 imr = readl(port->membase + CDNS_UART_IMR);
1228 writel(imr, port->membase + CDNS_UART_IDR);
1229
1230 /*
1231 * Make sure that the tx part is enabled. Set the TX enable bit and
1232 * clear the TX disable bit to enable the transmitter.
1233 */
1234 ctrl = readl(port->membase + CDNS_UART_CR);
1235 ctrl &= ~CDNS_UART_CR_TX_DIS;
1236 ctrl |= CDNS_UART_CR_TX_EN;
1237 writel(ctrl, port->membase + CDNS_UART_CR);
1238
1239 uart_console_write(port, s, count, cdns_uart_console_putchar);
1240 cdns_uart_console_wait_tx(port);
1241
1242 writel(ctrl, port->membase + CDNS_UART_CR);
1243
1244 /* restore interrupt state */
1245 writel(imr, port->membase + CDNS_UART_IER);
1246
1247 if (locked)
1248 spin_unlock_irqrestore(&port->lock, flags);
1249 }
1250
1251 /**
1252 * cdns_uart_console_setup - Initialize the uart to default config
1253 * @co: Console handle
1254 * @options: Initial settings of uart
1255 *
1256 * Return: 0 on success, negative errno otherwise.
1257 */
cdns_uart_console_setup(struct console * co,char * options)1258 static int __init cdns_uart_console_setup(struct console *co, char *options)
1259 {
1260 struct uart_port *port = &cdns_uart_port[co->index];
1261 int baud = 9600;
1262 int bits = 8;
1263 int parity = 'n';
1264 int flow = 'n';
1265
1266 if (co->index < 0 || co->index >= CDNS_UART_NR_PORTS)
1267 return -EINVAL;
1268
1269 if (!port->membase) {
1270 pr_debug("console on " CDNS_UART_TTY_NAME "%i not present\n",
1271 co->index);
1272 return -ENODEV;
1273 }
1274
1275 if (options)
1276 uart_parse_options(options, &baud, &parity, &bits, &flow);
1277
1278 return uart_set_options(port, co, baud, parity, bits, flow);
1279 }
1280
1281 static struct uart_driver cdns_uart_uart_driver;
1282
1283 static struct console cdns_uart_console = {
1284 .name = CDNS_UART_TTY_NAME,
1285 .write = cdns_uart_console_write,
1286 .device = uart_console_device,
1287 .setup = cdns_uart_console_setup,
1288 .flags = CON_PRINTBUFFER,
1289 .index = -1, /* Specified on the cmdline (e.g. console=ttyPS ) */
1290 .data = &cdns_uart_uart_driver,
1291 };
1292
1293 /**
1294 * cdns_uart_console_init - Initialization call
1295 *
1296 * Return: 0 on success, negative errno otherwise
1297 */
cdns_uart_console_init(void)1298 static int __init cdns_uart_console_init(void)
1299 {
1300 register_console(&cdns_uart_console);
1301 return 0;
1302 }
1303
1304 console_initcall(cdns_uart_console_init);
1305
1306 #endif /* CONFIG_SERIAL_XILINX_PS_UART_CONSOLE */
1307
1308 static struct uart_driver cdns_uart_uart_driver = {
1309 .owner = THIS_MODULE,
1310 .driver_name = CDNS_UART_NAME,
1311 .dev_name = CDNS_UART_TTY_NAME,
1312 .major = CDNS_UART_MAJOR,
1313 .minor = CDNS_UART_MINOR,
1314 .nr = CDNS_UART_NR_PORTS,
1315 #ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
1316 .cons = &cdns_uart_console,
1317 #endif
1318 };
1319
1320 #ifdef CONFIG_PM_SLEEP
1321 /**
1322 * cdns_uart_suspend - suspend event
1323 * @device: Pointer to the device structure
1324 *
1325 * Return: 0
1326 */
cdns_uart_suspend(struct device * device)1327 static int cdns_uart_suspend(struct device *device)
1328 {
1329 struct uart_port *port = dev_get_drvdata(device);
1330 struct tty_struct *tty;
1331 struct device *tty_dev;
1332 int may_wake = 0;
1333
1334 /* Get the tty which could be NULL so don't assume it's valid */
1335 tty = tty_port_tty_get(&port->state->port);
1336 if (tty) {
1337 tty_dev = tty->dev;
1338 may_wake = device_may_wakeup(tty_dev);
1339 tty_kref_put(tty);
1340 }
1341
1342 /*
1343 * Call the API provided in serial_core.c file which handles
1344 * the suspend.
1345 */
1346 uart_suspend_port(&cdns_uart_uart_driver, port);
1347 if (console_suspend_enabled && !may_wake) {
1348 struct cdns_uart *cdns_uart = port->private_data;
1349
1350 clk_disable(cdns_uart->uartclk);
1351 clk_disable(cdns_uart->pclk);
1352 } else {
1353 unsigned long flags = 0;
1354
1355 spin_lock_irqsave(&port->lock, flags);
1356 /* Empty the receive FIFO 1st before making changes */
1357 while (!(readl(port->membase + CDNS_UART_SR) &
1358 CDNS_UART_SR_RXEMPTY))
1359 readl(port->membase + CDNS_UART_FIFO);
1360 /* set RX trigger level to 1 */
1361 writel(1, port->membase + CDNS_UART_RXWM);
1362 /* disable RX timeout interrups */
1363 writel(CDNS_UART_IXR_TOUT, port->membase + CDNS_UART_IDR);
1364 spin_unlock_irqrestore(&port->lock, flags);
1365 }
1366
1367 return 0;
1368 }
1369
1370 /**
1371 * cdns_uart_resume - Resume after a previous suspend
1372 * @device: Pointer to the device structure
1373 *
1374 * Return: 0
1375 */
cdns_uart_resume(struct device * device)1376 static int cdns_uart_resume(struct device *device)
1377 {
1378 struct uart_port *port = dev_get_drvdata(device);
1379 unsigned long flags = 0;
1380 u32 ctrl_reg;
1381 struct tty_struct *tty;
1382 struct device *tty_dev;
1383 int may_wake = 0;
1384
1385 /* Get the tty which could be NULL so don't assume it's valid */
1386 tty = tty_port_tty_get(&port->state->port);
1387 if (tty) {
1388 tty_dev = tty->dev;
1389 may_wake = device_may_wakeup(tty_dev);
1390 tty_kref_put(tty);
1391 }
1392
1393 if (console_suspend_enabled && !may_wake) {
1394 struct cdns_uart *cdns_uart = port->private_data;
1395
1396 clk_enable(cdns_uart->pclk);
1397 clk_enable(cdns_uart->uartclk);
1398
1399 spin_lock_irqsave(&port->lock, flags);
1400
1401 /* Set TX/RX Reset */
1402 ctrl_reg = readl(port->membase + CDNS_UART_CR);
1403 ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
1404 writel(ctrl_reg, port->membase + CDNS_UART_CR);
1405 while (readl(port->membase + CDNS_UART_CR) &
1406 (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
1407 cpu_relax();
1408
1409 /* restore rx timeout value */
1410 writel(rx_timeout, port->membase + CDNS_UART_RXTOUT);
1411 /* Enable Tx/Rx */
1412 ctrl_reg = readl(port->membase + CDNS_UART_CR);
1413 ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
1414 ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
1415 writel(ctrl_reg, port->membase + CDNS_UART_CR);
1416
1417 spin_unlock_irqrestore(&port->lock, flags);
1418 } else {
1419 spin_lock_irqsave(&port->lock, flags);
1420 /* restore original rx trigger level */
1421 writel(rx_trigger_level, port->membase + CDNS_UART_RXWM);
1422 /* enable RX timeout interrupt */
1423 writel(CDNS_UART_IXR_TOUT, port->membase + CDNS_UART_IER);
1424 spin_unlock_irqrestore(&port->lock, flags);
1425 }
1426
1427 return uart_resume_port(&cdns_uart_uart_driver, port);
1428 }
1429 #endif /* ! CONFIG_PM_SLEEP */
1430
1431 static SIMPLE_DEV_PM_OPS(cdns_uart_dev_pm_ops, cdns_uart_suspend,
1432 cdns_uart_resume);
1433
1434 static const struct cdns_platform_data zynqmp_uart_def = {
1435 .quirks = CDNS_UART_RXBS_SUPPORT, };
1436
1437 /* Match table for of_platform binding */
1438 static const struct of_device_id cdns_uart_of_match[] = {
1439 { .compatible = "xlnx,xuartps", },
1440 { .compatible = "cdns,uart-r1p8", },
1441 { .compatible = "cdns,uart-r1p12", .data = &zynqmp_uart_def },
1442 { .compatible = "xlnx,zynqmp-uart", .data = &zynqmp_uart_def },
1443 {}
1444 };
1445 MODULE_DEVICE_TABLE(of, cdns_uart_of_match);
1446
1447 /**
1448 * cdns_uart_probe - Platform driver probe
1449 * @pdev: Pointer to the platform device structure
1450 *
1451 * Return: 0 on success, negative errno otherwise
1452 */
cdns_uart_probe(struct platform_device * pdev)1453 static int cdns_uart_probe(struct platform_device *pdev)
1454 {
1455 int rc, id, irq;
1456 struct uart_port *port;
1457 struct resource *res;
1458 struct cdns_uart *cdns_uart_data;
1459 const struct of_device_id *match;
1460
1461 cdns_uart_data = devm_kzalloc(&pdev->dev, sizeof(*cdns_uart_data),
1462 GFP_KERNEL);
1463 if (!cdns_uart_data)
1464 return -ENOMEM;
1465
1466 match = of_match_node(cdns_uart_of_match, pdev->dev.of_node);
1467 if (match && match->data) {
1468 const struct cdns_platform_data *data = match->data;
1469
1470 cdns_uart_data->quirks = data->quirks;
1471 }
1472
1473 cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "pclk");
1474 if (IS_ERR(cdns_uart_data->pclk)) {
1475 cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "aper_clk");
1476 if (!IS_ERR(cdns_uart_data->pclk))
1477 dev_err(&pdev->dev, "clock name 'aper_clk' is deprecated.\n");
1478 }
1479 if (IS_ERR(cdns_uart_data->pclk)) {
1480 dev_err(&pdev->dev, "pclk clock not found.\n");
1481 return PTR_ERR(cdns_uart_data->pclk);
1482 }
1483
1484 cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "uart_clk");
1485 if (IS_ERR(cdns_uart_data->uartclk)) {
1486 cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "ref_clk");
1487 if (!IS_ERR(cdns_uart_data->uartclk))
1488 dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n");
1489 }
1490 if (IS_ERR(cdns_uart_data->uartclk)) {
1491 dev_err(&pdev->dev, "uart_clk clock not found.\n");
1492 return PTR_ERR(cdns_uart_data->uartclk);
1493 }
1494
1495 rc = clk_prepare(cdns_uart_data->pclk);
1496 if (rc) {
1497 dev_err(&pdev->dev, "Unable to enable pclk clock.\n");
1498 return rc;
1499 }
1500 rc = clk_prepare(cdns_uart_data->uartclk);
1501 if (rc) {
1502 dev_err(&pdev->dev, "Unable to enable device clock.\n");
1503 goto err_out_clk_dis_pclk;
1504 }
1505
1506 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1507 if (!res) {
1508 rc = -ENODEV;
1509 goto err_out_clk_disable;
1510 }
1511
1512 irq = platform_get_irq(pdev, 0);
1513 if (irq <= 0) {
1514 rc = -ENXIO;
1515 goto err_out_clk_disable;
1516 }
1517
1518 #ifdef CONFIG_COMMON_CLK
1519 cdns_uart_data->clk_rate_change_nb.notifier_call =
1520 cdns_uart_clk_notifier_cb;
1521 if (clk_notifier_register(cdns_uart_data->uartclk,
1522 &cdns_uart_data->clk_rate_change_nb))
1523 dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
1524 #endif
1525 /* Look for a serialN alias */
1526 id = of_alias_get_id(pdev->dev.of_node, "serial");
1527 if (id < 0)
1528 id = 0;
1529
1530 /* Initialize the port structure */
1531 port = cdns_uart_get_port(id);
1532
1533 if (!port) {
1534 dev_err(&pdev->dev, "Cannot get uart_port structure\n");
1535 rc = -ENODEV;
1536 goto err_out_notif_unreg;
1537 }
1538
1539 /*
1540 * Register the port.
1541 * This function also registers this device with the tty layer
1542 * and triggers invocation of the config_port() entry point.
1543 */
1544 port->mapbase = res->start;
1545 port->irq = irq;
1546 port->dev = &pdev->dev;
1547 port->uartclk = clk_get_rate(cdns_uart_data->uartclk);
1548 port->private_data = cdns_uart_data;
1549 cdns_uart_data->port = port;
1550 platform_set_drvdata(pdev, port);
1551
1552 rc = uart_add_one_port(&cdns_uart_uart_driver, port);
1553 if (rc) {
1554 dev_err(&pdev->dev,
1555 "uart_add_one_port() failed; err=%i\n", rc);
1556 goto err_out_notif_unreg;
1557 }
1558
1559 return 0;
1560
1561 err_out_notif_unreg:
1562 #ifdef CONFIG_COMMON_CLK
1563 clk_notifier_unregister(cdns_uart_data->uartclk,
1564 &cdns_uart_data->clk_rate_change_nb);
1565 #endif
1566 err_out_clk_disable:
1567 clk_unprepare(cdns_uart_data->uartclk);
1568 err_out_clk_dis_pclk:
1569 clk_unprepare(cdns_uart_data->pclk);
1570
1571 return rc;
1572 }
1573
1574 /**
1575 * cdns_uart_remove - called when the platform driver is unregistered
1576 * @pdev: Pointer to the platform device structure
1577 *
1578 * Return: 0 on success, negative errno otherwise
1579 */
cdns_uart_remove(struct platform_device * pdev)1580 static int cdns_uart_remove(struct platform_device *pdev)
1581 {
1582 struct uart_port *port = platform_get_drvdata(pdev);
1583 struct cdns_uart *cdns_uart_data = port->private_data;
1584 int rc;
1585
1586 /* Remove the cdns_uart port from the serial core */
1587 #ifdef CONFIG_COMMON_CLK
1588 clk_notifier_unregister(cdns_uart_data->uartclk,
1589 &cdns_uart_data->clk_rate_change_nb);
1590 #endif
1591 rc = uart_remove_one_port(&cdns_uart_uart_driver, port);
1592 port->mapbase = 0;
1593 clk_unprepare(cdns_uart_data->uartclk);
1594 clk_unprepare(cdns_uart_data->pclk);
1595 return rc;
1596 }
1597
1598 static struct platform_driver cdns_uart_platform_driver = {
1599 .probe = cdns_uart_probe,
1600 .remove = cdns_uart_remove,
1601 .driver = {
1602 .name = CDNS_UART_NAME,
1603 .of_match_table = cdns_uart_of_match,
1604 .pm = &cdns_uart_dev_pm_ops,
1605 },
1606 };
1607
cdns_uart_init(void)1608 static int __init cdns_uart_init(void)
1609 {
1610 int retval = 0;
1611
1612 /* Register the cdns_uart driver with the serial core */
1613 retval = uart_register_driver(&cdns_uart_uart_driver);
1614 if (retval)
1615 return retval;
1616
1617 /* Register the platform driver */
1618 retval = platform_driver_register(&cdns_uart_platform_driver);
1619 if (retval)
1620 uart_unregister_driver(&cdns_uart_uart_driver);
1621
1622 return retval;
1623 }
1624
cdns_uart_exit(void)1625 static void __exit cdns_uart_exit(void)
1626 {
1627 /* Unregister the platform driver */
1628 platform_driver_unregister(&cdns_uart_platform_driver);
1629
1630 /* Unregister the cdns_uart driver */
1631 uart_unregister_driver(&cdns_uart_uart_driver);
1632 }
1633
1634 module_init(cdns_uart_init);
1635 module_exit(cdns_uart_exit);
1636
1637 MODULE_DESCRIPTION("Driver for Cadence UART");
1638 MODULE_AUTHOR("Xilinx Inc.");
1639 MODULE_LICENSE("GPL");
1640