Searched full:gpio3 (Results 1 – 25 of 81) sorted by relevance
1234
| /Documentation/devicetree/bindings/watchdog/ |
| D | men-a021-wdt.txt | 19 gpios = <&gpio3 9 1 /* WD_EN */
20 &gpio3 10 1 /* WD_FAST */
21 &gpio3 11 1 /* WD_TRIG */
22 &gpio3 6 1 /* RST_CAUSE[0] */
23 &gpio3 7 1 /* RST_CAUSE[1] */
24 &gpio3 8 1>; /* RST_CAUSE[2] */
|
| /Documentation/devicetree/bindings/sound/ |
| D | maxim,max9759.txt | 14 shutdown-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
15 mute-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
16 gain-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>,
17 <&gpio3 25 GPIO_ACTIVE_LOW>;
|
| D | soc-ac97link.txt | 25 ac97-gpios = <&gpio3 20 0 &gpio3 22 0 &gpio3 28 0>;
|
| D | rt5640.txt | 28 2: using GPIO3 pin as dmic1 data pin
42 5: Use GPIO3 for jack-detect
|
| D | uda1334.txt | 16 nxp,deemph-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
|
| D | adi,ssm2305.txt | 13 shutdown-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/hsi/ |
| D | nokia-modem.txt | 46 interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */
48 gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */
49 <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */
50 <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */
51 <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */
|
| /Documentation/devicetree/bindings/arm/ |
| D | ste-nomadik.txt | 31 gpios = <&gpio3 19 0x1>;
33 interrupt-parent = <&gpio3>;
36 gpios = <&gpio3 16 0x1>;
|
| /Documentation/devicetree/bindings/net/nfc/ |
| D | nfcmrvl.txt | 32 reset-n-io = <&gpio3 16 0>;
51 interrupt-parent = <&gpio3>;
58 reset-n-io = <&gpio3 19 0>;
82 reset-n-io = <&gpio3 19 0>;
|
| D | pn544.txt | 30 enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
31 firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | cirrus,lochnagar.txt | 52 fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4, fpga-gpio5,
53 fpga-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
55 dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
56 gf-gpio3, gf-gpio7, codec-aif1-bclk, codec-aif1-rxdat,
78 aif, fpga-gpio1, fpga-gpio2, fpga-gpio3, fpga-gpio4, fpga-gpio5,
79 fpga-gpio6, codec-gpio1, codec-gpio2, codec-gpio3, codec-gpio4,
81 dsp-gpio2, dsp-gpio3, dsp-gpio4, dsp-gpio5, dsp-gpio6, gf-gpio2,
82 gf-gpio3, gf-gpio7, gf-gpio1, gf-gpio5, dsp-gpio20, codec-clkout,
|
| D | ste,nomadik.txt | 79 nomadik-gpio-chips = <&gpio0>, <&gpio1>, <&gpio2>, <&gpio3>;
119 pins = "GPIO1", "GPIO3";
133 pins = "GPIO3";
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | sis_i2c.txt | 27 interrupt-parent = <&gpio3>;
29 irq-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
|
| D | ar1021.txt | 13 interrupt-parent = <&gpio3>;
|
| D | max11801-ts.txt | 14 interrupt-parent = <&gpio3>;
|
| /Documentation/devicetree/bindings/gpio/ |
| D | gpio-mxs.txt | 36 gpio3 = &gpio3;
71 gpio3: gpio@3 {
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | cpcap-charger.txt | 29 mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW
30 &gpio3 23 GPIO_ACTIVE_LOW>;
|
| D | isp1704.txt | 15 nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | toshiba,tc358767.txt | 29 shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
30 reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/serial/ |
| D | nxp,sc16is7xx.txt | 30 interrupt-parent = <&gpio3>;
64 interrupt-parent = <&gpio3>;
|
| /Documentation/devicetree/bindings/input/ |
| D | gpio-beeper.txt | 12 gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/leds/backlight/ |
| D | gpio-backlight.txt | 14 gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/thermal/ |
| D | ti_soc_thermal.txt | 55 gpios = <&gpio3 22 0>; /* tshut */
65 gpios = <&gpio3 22 0>; /* tshut */
|
| /Documentation/devicetree/bindings/spi/ |
| D | fsl-imx-cspi.txt | 48 cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */
49 <&gpio3 25 0>; /* GPIO3_25 */
|
| /Documentation/devicetree/bindings/mfd/ |
| D | as3711.txt | 33 - su2-fbprot-gpio3 : GPIO3 is used for over-voltage protection
|
1234