Searched +full:lcd +full:- +full:supply (Results 1 – 25 of 73) sorted by relevance
123
| /Documentation/devicetree/bindings/display/panel/ |
| D | olimex,lcd-olinuxino.txt | 1 Binding for Olimex Ltd. LCD-OLinuXino bridge panel.
3 This device can be used as bridge between a host controller and LCD panels.
5 - LCD-OLinuXino-4.3TS
6 - LCD-OLinuXino-5
7 - LCD-OLinuXino-7
8 - LCD-OLinuXino-10
11 - AT24C16C EEPROM holding panel identification and timing requirements
12 - AR1021 resistive touch screen controller (optional)
13 - FT5x6 capacitive touch screnn controller (optional)
14 - GT911/GT928 capacitive touch screen controller (optional)
[all …]
|
| D | sitronix,st7701.txt | 1 Sitronix ST7701 based LCD panels
3 ST7701 designed for small and medium sizes of TFT LCD display, is
7 Techstar TS8550B is 480x854, 2-lane MIPI DSI LCD panel which has
11 - compatible: must be "sitronix,st7701" and one of
13 - reset-gpios: a GPIO phandle for the reset pin
16 - reg: DSI virtual channel used by that screen
17 - VCC-supply: analog regulator for MIPI circuit
18 - IOVCC-supply: I/O system regulator
21 - backlight: phandle for the backlight control.
26 VCC-supply = <®_dldo2>;
[all …]
|
| D | friendlyarm,hd702e.txt | 1 FriendlyELEC HD702E 800x1280 LCD panel
3 HD702E lcd is FriendlyELEC developed eDP LCD panel with 800x1280
8 - compatible: should be "friendlyarm,hd702e"
9 - power-supply: regulator to provide the supply voltage
12 - backlight: phandle of the backlight device attached to the panel
15 - Video port for LCD panel input.
17 This binding is compatible with the simple-panel binding, which is specified
18 in simple-panel.txt in this directory.
23 compatible ="friendlyarm,hd702e", "simple-panel";
25 power-supply = <&vcc3v3_sys>;
[all …]
|
| D | feiyang,fy07024di26a30d.txt | 1 Feiyang FY07024DI26A30-D 7" MIPI-DSI LCD Panel
4 - compatible: must be "feiyang,fy07024di26a30d"
5 - reg: DSI virtual channel used by that screen
6 - avdd-supply: analog regulator dc1 switch
7 - dvdd-supply: 3v3 digital regulator
8 - reset-gpios: a GPIO phandle for the reset pin
11 - backlight: phandle for the backlight control.
16 avdd-supply = <®_dc1sw>;
17 dvdd-supply = <®_dldo2>;
18 reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */
|
| D | auo,g070vvn01.txt | 1 AU Optronics Corporation 7.0" FHD (800 x 480) TFT LCD panel
4 - compatible: should be "auo,g070vvn01"
5 - backlight: phandle of the backlight device attached to the panel
6 - power-supply: single regulator to provide the supply voltage
9 - port: Parallel port mapping to connect this display
11 This panel needs single power supply voltage. Its backlight is conntrolled
15 --------
17 Example device-tree definition when connected to iMX6Q based board
19 lcd_panel: lcd-panel {
22 power-supply = <®_display>;
[all …]
|
| D | koe,tx14d24vm1bpa.txt | 1 Kaohsiung Opto-Electronics Inc. 5.7" QVGA (320 x 240) TFT LCD panel
4 - compatible: should be "koe,tx14d24vm1bpa"
5 - backlight: phandle of the backlight device attached to the panel
6 - power-supply: single regulator to provide the supply voltage
9 - port: Parallel port mapping to connect this display
11 This panel needs single power supply voltage. Its backlight is conntrolled
15 --------
17 Example device-tree definition when connected to iMX53 based board
19 lcd_panel: lcd-panel {
22 power-supply = <®_3v3>;
[all …]
|
| D | orisetech,otm8009a.txt | 1 Orise Tech OTM8009A 3.97" 480x800 TFT LCD panel (MIPI-DSI video mode)
3 The Orise Tech OTM8009A is a 3.97" 480x800 TFT LCD panel connected using
4 a MIPI-DSI video interface. Its backlight is managed through the DSI link.
7 - compatible: "orisetech,otm8009a"
8 - reg: the virtual channel number of a DSI peripheral
11 - reset-gpios: a GPIO spec for the reset pin (active low).
12 - power-supply: phandle of the regulator that provides the supply voltage.
20 reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>;
21 power-supply = <&v1v8>;
|
| D | raydium,rm68200.txt | 1 Raydium Semiconductor Corporation RM68200 5.5" 720p MIPI-DSI TFT LCD panel
3 The Raydium Semiconductor Corporation RM68200 is a 5.5" 720x1280 TFT LCD
4 panel connected using a MIPI-DSI video interface.
7 - compatible: "raydium,rm68200"
8 - reg: the virtual channel number of a DSI peripheral
11 - reset-gpios: a GPIO spec for the reset pin (active low).
12 - power-supply: phandle of the regulator that provides the supply voltage.
13 - backlight: phandle of the backlight device attached to the panel.
21 reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>;
22 power-supply = <&v1v8>;
|
| D | samsung,ld9040.txt | 1 Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus
4 - compatible: "samsung,ld9040"
5 - reg: address of the panel on SPI bus
6 - vdd3-supply: core voltage supply
7 - vci-supply: voltage supply for analog circuits
8 - reset-gpios: a GPIO spec for the reset pin
9 - display-timings: timings for the connected panel according to [1]
14 - power-on-delay: delay after turning regulators on [ms]
15 - reset-delay: delay after reset sequence [ms]
16 - panel-width-mm: physical panel width [mm]
[all …]
|
| D | nec,nl12880b20-05.txt | 1 NEC LCD Technologies, Ltd. 12.1" WXGA (1280x800) LVDS TFT LCD panel
4 - compatible: should be "nec,nl12880bc20-05"
5 - power-supply: as specified in the base binding
7 This binding is compatible with the simple-panel binding, which is specified
8 in simple-panel.txt in this directory.
|
| D | rocktech,jh057n00900.txt | 1 Rocktech jh057n00900 5.5" 720x1440 TFT LCD panel
4 - compatible: should be "rocktech,jh057n00900"
5 - reg: DSI virtual channel of the peripheral
6 - reset-gpios: panel reset gpio
7 - backlight: phandle of the backlight device attached to the panel
8 - vcc-supply: phandle of the regulator that provides the vcc supply voltage.
9 - iovcc-supply: phandle of the regulator that provides the iovcc supply
19 reset-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
20 vcc-supply = <®_2v8_p>;
21 iovcc-supply = <®_1v8_p>;
|
| D | sharp,ls037v7dw01.txt | 1 SHARP LS037V7DW01 TFT-LCD panel
5 - compatible: "sharp,ls037v7dw01"
8 - label: a symbolic name for the panel
9 - enable-gpios: a GPIO spec for the optional enable pin.
11 - reset-gpios: a GPIO spec for the optional reset pin.
13 - mode-gpios: a GPIO
17 - Video port for DPI input
25 -------
31 power-supply = <&lcd_3v3>;
32 enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */
[all …]
|
| D | ronbo,rb070d30.yaml | 1 # SPDX-License-Identifier: (GPL-2.0+ OR X11)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Maxime Ripard <maxime.ripard@bootlin.com>
17 description: MIPI-DSI virtual channel
19 power-gpios:
23 reset-gpios:
27 shlr-gpios:
31 updn-gpios:
35 vcc-lcd-supply:
[all …]
|
| D | panasonic,vvx10f034n00.txt | 1 Panasonic 10" WUXGA TFT LCD panel
4 - compatible: should be "panasonic,vvx10f034n00"
5 - reg: DSI virtual channel of the peripheral
6 - power-supply: phandle of the regulator that provides the supply voltage
9 - backlight: phandle of the backlight device attached to the panel
17 power-supply = <&vreg_vsp>;
|
| D | innolux,p097pfg.txt | 1 Innolux P097PFG 9.7" 1536x2048 TFT LCD panel
4 - compatible: should be "innolux,p097pfg"
5 - reg: DSI virtual channel of the peripheral
6 - avdd-supply: phandle of the regulator that provides positive voltage
7 - avee-supply: phandle of the regulator that provides negative voltage
8 - enable-gpios: panel enable gpio
11 - backlight: phandle of the backlight device attached to the panel
19 avdd-supply = <...>;
20 avee-supply = <...>;
22 enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
|
| D | tianma,tm070rvhg71.txt | 1 Tianma Micro-electronics TM070RVHG71 7.0" WXGA TFT LCD panel
4 - compatible: should be "tianma,tm070rvhg71"
5 - power-supply: single regulator to provide the supply voltage
6 - backlight: phandle of the backlight device attached to the panel
9 - port: LVDS port mapping to connect this display
11 This panel needs single power supply voltage. Its backlight is conntrolled
15 --------
17 Example device-tree definition when connected to iMX6Q based board
19 panel: panel-lvds0 {
22 power-supply = <®_lvds>;
[all …]
|
| D | innolux,p079zca.txt | 1 Innolux P079ZCA 7.85" 768x1024 TFT LCD panel
4 - compatible: should be "innolux,p079zca"
5 - reg: DSI virtual channel of the peripheral
6 - power-supply: phandle of the regulator that provides the supply voltage
7 - enable-gpios: panel enable gpio
10 - backlight: phandle of the backlight device attached to the panel
18 power-supply = <...>;
20 enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
|
| D | kingdisplay,kd097d04.txt | 1 Kingdisplay KD097D04 9.7" 1536x2048 TFT LCD panel
4 - compatible: should be "kingdisplay,kd097d04"
5 - reg: DSI virtual channel of the peripheral
6 - power-supply: phandle of the regulator that provides the supply voltage
7 - enable-gpios: panel enable gpio
10 - backlight: phandle of the backlight device attached to the panel
18 power-supply = <...>;
20 enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/display/ |
| D | cirrus,clps711x-fb.txt | 4 - compatible: Shall contain "cirrus,ep7209-fb".
5 - reg : Physical base address and length of the controller's registers +
7 - clocks : phandle + clock specifier pair of the FB reference clock.
8 - display : phandle to a display node as described in
9 Documentation/devicetree/bindings/display/panel/display-timing.txt.
11 - bits-per-pixel: Bits per pixel.
12 - ac-prescale : LCD AC bias frequency. This frequency is the required
13 AC bias frequency for a given manufacturer's LCD plate.
14 - cmap-invert : Invert the color levels (Optional).
17 - lcd-supply: Regulator for LCD supply voltage.
[all …]
|
| D | ste,mcde.txt | 1 ST-Ericsson Multi Channel Display Engine MCDE
3 The ST-Ericsson MCDE is a display controller with support for compositing
5 LCD displays or bridges. It is used in the ST-Ericsson U8500 platform.
9 - compatible: must be:
11 - reg: register base for the main MCDE control registers, should be
13 - interrupts: the interrupt line for the MCDE
14 - epod-supply: a phandle to the EPOD regulator
15 - vana-supply: a phandle to the analog voltage regulator
16 - clocks: an array of the MCDE clocks in this strict order:
17 MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI
[all …]
|
| D | ingenic,lcd.txt | 1 Ingenic JZ47xx LCD driver
4 - compatible: one of:
5 * ingenic,jz4740-lcd
6 * ingenic,jz4725b-lcd
7 - reg: LCD registers location and length
8 - clocks: LCD pixclock and device clock specifiers.
10 - clock-names: "lcd_pclk" and "lcd"
11 - interrupts: Specifies the interrupt line the LCD controller is connected to.
19 power-supply = <&vcc>;
23 remote-endpoint = <&panel_output>;
[all …]
|
| D | atmel,lcdc.txt | 2 -----------------------------------------------------
5 - compatible :
6 "atmel,at91sam9261-lcdc" ,
7 "atmel,at91sam9263-lcdc" ,
8 "atmel,at91sam9g10-lcdc" ,
9 "atmel,at91sam9g45-lcdc" ,
10 "atmel,at91sam9g45es-lcdc" ,
11 "atmel,at91sam9rl-lcdc" ,
12 "atmel,at32ap-lcdc"
13 - reg : Should contain 1 register ranges(address and length).
[all …]
|
| D | truly,nt35597.txt | 7 - compatible: should be "truly,nt35597-2K-display"
8 - vdda-supply: phandle of the regulator that provides the supply voltage
9 Power IC supply
10 - vdispp-supply: phandle of the regulator that provides the supply voltage
11 for positive LCD bias
12 - vdispn-supply: phandle of the regulator that provides the supply voltage
13 for negative LCD bias
14 - reset-gpios: phandle of gpio for reset line
15 This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names
17 - mode-gpios: phandle of the gpio for choosing the mode of the display
[all …]
|
| D | marvell,pxa2xx-lcdc.txt | 1 PXA LCD Controller
2 ------------------
5 - compatible : one of these
6 "marvell,pxa2xx-lcdc",
7 "marvell,pxa270-lcdc",
8 "marvell,pxa300-lcdc"
9 - reg : should contain 1 register range (address and length).
10 - interrupts : framebuffer controller interrupt.
11 - clocks: phandle to input clocks
14 - lcd-supply: A phandle to a power regulator that controls the LCD voltage.
[all …]
|
| D | st,stm32-ltdc.txt | 1 * STMicroelectronics STM32 lcd-tft display controller
3 - ltdc: lcd-tft display controller host
5 - compatible: "st,stm32-ltdc"
6 - reg: Physical base address of the IP registers and length of memory mapped region.
7 - clocks: A list of phandle + clock-specifier pairs, one for each
8 entry in 'clock-names'.
9 - clock-names: A list of clock names. For ltdc it should contain:
10 - "lcd" for the clock feeding the output pixel clock & IP clock.
11 - resets: reset to be used by the device (defined by use of RCC macro).
13 - Video port for DPI RGB output: ltdc has one video port with up to 2
[all …]
|
123