Searched full:named (Results 1 – 25 of 362) sorted by relevance
12345678910>>...15
| /Documentation/ABI/testing/ |
| D | sysfs-class-led-trigger-netdev | 21 Signal the link state of the named network device.
24 of the named network device.
32 Signal transmission of data on the named network device.
42 Signal reception of data on the named network device.
|
| D | sysfs-devices-system-xen_cpu | 8 subdirectories named by the Xen's logical cpu number, e.g.:
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-st.txt | 10 - A pinctrl state named "default" must be defined to set pins in mode of
21 - A pinctrl state named "idle" could be defined to set pins in idle state
23 - A pinctrl state named "sleep" could be defined to set pins in sleep state
|
| /Documentation/devicetree/bindings/sound/ |
| D | sirf-audio-port.txt | 11 named "tx") and one for reception (should be named "rx").
|
| D | brcm,bcm2835-i2s.txt | 12 named "tx") and one for reception (should be named "rx").
|
| D | sirf-usp.txt | 11 named "tx") and one for reception (should be named "rx").
|
| /Documentation/devicetree/bindings/serial/ |
| D | nxp,lpc1850-uart.txt | 14 be at least one channel named "tx" for transmit
15 and named "rx" for receive.
|
| D | pl011.yaml | 47 When present, must have one state named "default",
48 and may contain a second name named "sleep". The former
60 the clock named UARTCLK on the IP block, i.e. the clock
|
| /Documentation/networking/ |
| D | netif-msg.txt | 30 Initially this message level variable was uniquely named in each driver
50 Adding a per-interface private variable named "msg_enable". The
64 The set of message levels is named
|
| D | cxacru.txt | 13 Detected devices will appear as ATM devices named "cxacru". In /sys/class/atm/
14 these are directories named cxacruN where N is the device number. A symlink
15 named device points to the USB interface device's directory which contains
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | resistive-adc-touch.txt | 17 - iio-channels: The third channel named "pressure" is optional and can be
21 - iio-channel-names: optional channel named "pressure".
|
| /Documentation/devicetree/bindings/spi/ |
| D | microchip,spi-pic32.txt | 18 named "spi-tx" for transmit and named "spi-rx" for receive.
|
| /Documentation/devicetree/bindings/clock/ |
| D | clock-bindings.txt | 42 - this node defines a device with two clock outputs, the first named
43 "ckil" and the second named "ckih". Consumer nodes always reference
76 clock-ranges: Empty property indicating that child nodes can inherit named
88 This represents a device with two clock inputs, named "baud" and "register".
128 * The oscillator is fixed-frequency, and provides one clock output, named "osc".
|
| D | clk-s5pv210-audss.txt | 17 a clock named "xxti".
20 specified, it is fixed to a clock named "iiscdclk0".
|
| /Documentation/devicetree/bindings/gpio/ |
| D | gpio.txt | 7 GPIO properties should be named "[<name>-]gpios", with <name> being the purpose
10 for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old
167 of passed named are less than ngpios) will still be used up until the last
284 2.3) GPIO ranges from named pin groups
290 Both both <pinctrl-base> and <count> must set to 0 when using named pin groups
301 If numerical and named pin groups are mixed, the string corresponding to a
324 in pinctrl2 are defined using the pin groups named "foo" and "bar".
327 were referenced by any gpio-ranges property to contain a property named
|
| /Documentation/devicetree/bindings/dma/ |
| D | renesas,rcar-dmac.txt | 4 controller instances named DMAC capable of serving multiple clients. Channels
42 - interrupt-names: one entry for the error interrupt, named "error", plus one
43 entry per channel, named "ch%u", where %u is the channel number ranging from
|
| /Documentation/devicetree/bindings/regulator/ |
| D | sky81452-regulator.txt | 4 - regulator node named lout.
|
| /Documentation/devicetree/bindings/usb/ |
| D | ulpi.txt | 5 binding. The host controller shall have a "ulpi" named node as a child, and
|
| /Documentation/i2c/busses/ |
| D | i2c-sis630.rst | 21 This can be interesting for chipsets not named
36 named chipsets.
|
| /Documentation/devicetree/bindings/input/ |
| D | dlink,dir685-touchkeys.txt | 5 board inside the router is named E119921.
|
| /Documentation/devicetree/bindings/display/ |
| D | renesas,du.txt | 34 named.
36 functional clocks must be named "du.x" with "x" being the channel
40 supplied they must be named "dclkin.x" with "x" being the input clock
|
| /Documentation/devicetree/bindings/reserved-memory/ |
| D | reserved-memory.txt | 84 one default of all device drivers (named linux,cma@72000000 and 64MiB in size),
85 one dedicated to the framebuffer device (named framebuffer@78000000, 8MiB), and
86 one for multimedia processing (named multimedia-memory@77000000, 64MiB).
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | abilis,tb10x-iomux.txt | 17 Every function is associated to one named pin group inside the pin controller
45 The named pin groups of GPIO ports can be used to define GPIO ranges as
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | renesas,lvds.txt | 30 first, and shall be named "fck".
33 named "extal" and "dclkin.x" respectively, with "x" being the DU_DOTCLKIN
|
| /Documentation/devicetree/bindings/iio/ |
| D | iio-bindings.txt | 60 Empty property indicating that child nodes can inherit named
71 This represents a device with two IIO inputs, named "vcc" and "vdd".
|
12345678910>>...15