Searched full:uses (Results 1 – 25 of 837) sorted by relevance
12345678910>>...34
| /Documentation/devicetree/bindings/iommu/ |
| D | mediatek,iommu.txt | 4 this M4U have two generations of HW architecture. Generation one uses flat
5 pagetable, and only supports 4K size page mapping. Generation two uses the
59 "mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW.
60 "mediatek,mt2712-m4u" for mt2712 which uses generation two m4u HW.
61 "mediatek,mt7623-m4u", "mediatek,mt2701-m4u" for mt7623 which uses
63 "mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW.
64 "mediatek,mt8183-m4u" for mt8183 which uses generation two m4u HW.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | max8997-regulator.txt | 25 [1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
30 If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
38 - max8997,pmic-buck1-uses-gpio-dvs: 'buck1' can be controlled by gpio dvs.
39 - max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
40 - max8997,pmic-buck5-uses-gpio-dvs: 'buck5' can be controlled by gpio dvs.
96 max8997,pmic-buck1-uses-gpio-dvs;
97 max8997,pmic-buck2-uses-gpio-dvs;
98 max8997,pmic-buck5-uses-gpio-dvs;
|
| D | samsung,s5m8767.txt | 31 [1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
36 If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
41 - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
42 - s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
43 - s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
85 s5m8767,pmic-buck2-uses-gpio-dvs;
86 s5m8767,pmic-buck3-uses-gpio-dvs;
87 s5m8767,pmic-buck4-uses-gpio-dvs;
|
| /Documentation/devicetree/bindings/display/ |
| D | ssd1307fb.txt | 22 - solomon,com-seq: Display uses sequential COM pin configuration
23 - solomon,com-lrremap: Display uses left-right COM pin remap
24 - solomon,com-invdir: Display uses inverted COM pin scan direction
37 - solomon,area-color-enable: Display uses color mode
|
| /Documentation/kbuild/ |
| D | Kconfig.recursion-issue-02 | 14 # core requirement, and one uses "select" while the other uses "depends on" to
32 # with CORE, one uses "depends on" while the other uses "select". Another
|
| /Documentation/misc-devices/ |
| D | bh1770glc.txt | 26 8 bit. Driver supports only one channel. Driver uses ALS results to estimate
30 Driver uses threshold interrupts to avoid need for polling the values.
51 RW - enable / disable chip. Uses counting logic
93 RW - enable / disable proximity - uses counting logic
|
| /Documentation/devicetree/bindings/fpga/ |
| D | xlnx,zynqmp-pcap-fpga.txt | 2 The ZynqMP SoC uses the PCAP (Processor configuration Port) to configure the
3 Programmable Logic (PL). The configuration uses the firmware interface.
|
| /Documentation/filesystems/ |
| D | gfs2.txt | 9 file system, but also uses a lock module to allow the computers coordinate
14 GFS uses interchangeable inter-node locking mechanisms, the currently
19 lock_dlm -- uses a distributed lock manager (dlm) for inter-node locking
|
| /Documentation/ABI/testing/ |
| D | sysfs-devices-system-ibm-rtl | 10 Users: The ibm-prtm userspace daemon uses this interface.
20 Users: The ibm-prtm userspace daemon uses this interface.
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | fsl,imx25-gcq.txt | 16 Required when at least one subnode uses the this reference.
18 Required when at least one subnode uses this reference.
20 Required when at least one subnode uses this reference.
|
| /Documentation/hwmon/ |
| D | pwm-fan.rst | 4 This driver enables the use of a PWM module to drive a fan. It uses the
15 a PWM output. It uses the generic PWM interface, thus it can be used with
|
| /Documentation/features/sched/membarrier-sync-core/ |
| D | arch-support.txt | 15 # x86-32 uses IRET as return from interrupt, which takes care of the IPI.
16 # However, it uses both IRET and SYSEXIT to go back to user-space. The IRET
19 # x86-64 uses IRET as return from interrupt, which takes care of the IPI.
|
| /Documentation/devicetree/bindings/clock/ |
| D | keystone-gate.txt | 3 Binding for Keystone gate control driver which uses PSC controller IP.
5 This binding uses the common clock binding[1].
|
| /Documentation/devicetree/bindings/arm/mediatek/ |
| D | mediatek,pericfg.txt | 21 The pericfg controller uses the common clk binding from
24 Also it uses the common reset controller binding from
|
| D | mediatek,infracfg.txt | 24 The infracfg controller uses the common clk binding from
27 Also it uses the common reset controller binding from
|
| /Documentation/driver-api/ |
| D | slimbus.rst | 11 MIPI (Mobile Industry Processor Interface) alliance. The bus uses master/slave
15 (System-on-Chip) and peripheral components (typically codec). SLIMbus uses
25 channel uses dedicated ports on the device.
51 Per specification, SLIMbus uses "clock gears" to do power management based on
107 mode. Controller uses this sequence when it decides to enter low-power mode so
|
| /Documentation/devicetree/bindings/dma/ |
| D | sirfsoc-dma.txt | 28 channel request line is 9 of the 2nd dma controller, while write channel uses
30 dma controller, while write channel uses 13 of the 1st dma controller:
|
| /Documentation/filesystems/ext4/ |
| D | allocators.rst | 17 The first tool that ext4 uses to combat fragmentation is the multi-block
24 extent. A second related trick that ext4 uses is delayed allocation.
32 The third trick that ext4 (and ext3) uses is that it tries to keep a
|
| /Documentation/ioctl/ |
| D | ioctl-decoding.rst | 9 uses 3 bits to encode read/write and 13 bits for size.
14 31-30 00 - no parameters: uses _IO macro
|
| /Documentation/driver-api/firmware/ |
| D | direct-fs-lookup.rst | 9 uses common core kernel file loader facility kernel_read_file_from_path().
14 races with lookups and avoid uses of the custom fallback mechanisms
|
| /Documentation/devicetree/bindings/net/wireless/ |
| D | qcom,ath10k.txt | 9 PCI based devices uses compatible string "qcom,ath10k" and takes calibration
13 AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
14 and also uses most of the properties defined in this doc (except
15 "qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
22 SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi".
|
| /Documentation/crypto/ |
| D | descore-readme.txt | 54 275us to set a new key (uses 1k of key tables)
66 53us per encryption (uses 2k of tables)
67 96us to set a new key (uses 2.25k of key tables)
84 68us per encryption (uses 2k of tables)
85 96us to set a new key (uses 2.25k of key tables)
106 108us per encryption (uses 34k worth of tables)
107 134us to set a new key (uses 32k of key tables to get this speed!)
116 also very modified for crypt. his iteration code uses 16k
121 165us per encryption (uses 6k worth of tables)
122 478us to set a new key (uses <1k of key tables)
[all …]
|
| /Documentation/ia64/ |
| D | aliasing.rst | 24 System memory typically uses the WB attribute. The UC attribute is
41 supported attributes for each region. At boot-time, the kernel uses
46 The kernel uses the efi_memmap table returned from GetMemoryMap() to
99 This uses remap_pfn_range(), which creates user mappings. These
120 "X" uses this to access VGA frame buffers. Using legacy_mem
142 This uses copy_from_user(), which implicitly uses a kernel
200 which uses a granule-sized UC mapping. This granule will cover some
|
| /Documentation/devicetree/bindings/clock/ti/ |
| D | fixed-factor-clock.txt | 5 This binding uses the common clock binding[1], and also uses the autoidle
|
| /Documentation/driver-api/rapidio/ |
| D | tsi721.rst | 12 To generate SRIO maintenance transactions this driver uses one of Tsi721 DMA
16 RapidIO messaging support uses dedicated messaging channels for each mailbox.
17 For inbound messages this driver uses destination ID matching to forward messages
76 by setting CONFIG_RAPIDIO_DMA_ENGINE option. Tsi721 miniport driver uses seven
|
12345678910>>...34