1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Regulator driver for National Semiconductors LP3972 PMIC chip
4 *
5 * Based on lp3971.c
6 */
7
8 #include <linux/bug.h>
9 #include <linux/err.h>
10 #include <linux/i2c.h>
11 #include <linux/module.h>
12 #include <linux/kernel.h>
13 #include <linux/regulator/driver.h>
14 #include <linux/regulator/lp3972.h>
15 #include <linux/slab.h>
16
17 struct lp3972 {
18 struct device *dev;
19 struct mutex io_lock;
20 struct i2c_client *i2c;
21 };
22
23 /* LP3972 Control Registers */
24 #define LP3972_SCR_REG 0x07
25 #define LP3972_OVER1_REG 0x10
26 #define LP3972_OVSR1_REG 0x11
27 #define LP3972_OVER2_REG 0x12
28 #define LP3972_OVSR2_REG 0x13
29 #define LP3972_VCC1_REG 0x20
30 #define LP3972_ADTV1_REG 0x23
31 #define LP3972_ADTV2_REG 0x24
32 #define LP3972_AVRC_REG 0x25
33 #define LP3972_CDTC1_REG 0x26
34 #define LP3972_CDTC2_REG 0x27
35 #define LP3972_SDTV1_REG 0x29
36 #define LP3972_SDTV2_REG 0x2A
37 #define LP3972_MDTV1_REG 0x32
38 #define LP3972_MDTV2_REG 0x33
39 #define LP3972_L2VCR_REG 0x39
40 #define LP3972_L34VCR_REG 0x3A
41 #define LP3972_SCR1_REG 0x80
42 #define LP3972_SCR2_REG 0x81
43 #define LP3972_OEN3_REG 0x82
44 #define LP3972_OSR3_REG 0x83
45 #define LP3972_LOER4_REG 0x84
46 #define LP3972_B2TV_REG 0x85
47 #define LP3972_B3TV_REG 0x86
48 #define LP3972_B32RC_REG 0x87
49 #define LP3972_ISRA_REG 0x88
50 #define LP3972_BCCR_REG 0x89
51 #define LP3972_II1RR_REG 0x8E
52 #define LP3972_II2RR_REG 0x8F
53
54 #define LP3972_SYS_CONTROL1_REG LP3972_SCR1_REG
55 /* System control register 1 initial value,
56 * bits 5, 6 and 7 are EPROM programmable */
57 #define SYS_CONTROL1_INIT_VAL 0x02
58 #define SYS_CONTROL1_INIT_MASK 0x1F
59
60 #define LP3972_VOL_CHANGE_REG LP3972_VCC1_REG
61 #define LP3972_VOL_CHANGE_FLAG_GO 0x01
62 #define LP3972_VOL_CHANGE_FLAG_MASK 0x03
63
64 /* LDO output enable mask */
65 #define LP3972_OEN3_L1EN BIT(0)
66 #define LP3972_OVER2_LDO2_EN BIT(2)
67 #define LP3972_OVER2_LDO3_EN BIT(3)
68 #define LP3972_OVER2_LDO4_EN BIT(4)
69 #define LP3972_OVER1_S_EN BIT(2)
70
71 static const unsigned int ldo1_voltage_map[] = {
72 1700000, 1725000, 1750000, 1775000, 1800000, 1825000, 1850000, 1875000,
73 1900000, 1925000, 1950000, 1975000, 2000000,
74 };
75
76 static const unsigned int ldo23_voltage_map[] = {
77 1800000, 1900000, 2000000, 2100000, 2200000, 2300000, 2400000, 2500000,
78 2600000, 2700000, 2800000, 2900000, 3000000, 3100000, 3200000, 3300000,
79 };
80
81 static const unsigned int ldo4_voltage_map[] = {
82 1000000, 1050000, 1100000, 1150000, 1200000, 1250000, 1300000, 1350000,
83 1400000, 1500000, 1800000, 1900000, 2500000, 2800000, 3000000, 3300000,
84 };
85
86 static const unsigned int ldo5_voltage_map[] = {
87 0, 0, 0, 0, 0, 850000, 875000, 900000,
88 925000, 950000, 975000, 1000000, 1025000, 1050000, 1075000, 1100000,
89 1125000, 1150000, 1175000, 1200000, 1225000, 1250000, 1275000, 1300000,
90 1325000, 1350000, 1375000, 1400000, 1425000, 1450000, 1475000, 1500000,
91 };
92
93 static const unsigned int buck1_voltage_map[] = {
94 725000, 750000, 775000, 800000, 825000, 850000, 875000, 900000,
95 925000, 950000, 975000, 1000000, 1025000, 1050000, 1075000, 1100000,
96 1125000, 1150000, 1175000, 1200000, 1225000, 1250000, 1275000, 1300000,
97 1325000, 1350000, 1375000, 1400000, 1425000, 1450000, 1475000, 1500000,
98 };
99
100 static const unsigned int buck23_voltage_map[] = {
101 0, 800000, 850000, 900000, 950000, 1000000, 1050000, 1100000,
102 1150000, 1200000, 1250000, 1300000, 1350000, 1400000, 1450000, 1500000,
103 1550000, 1600000, 1650000, 1700000, 1800000, 1900000, 2500000, 2800000,
104 3000000, 3300000,
105 };
106
107 static const int ldo_output_enable_mask[] = {
108 LP3972_OEN3_L1EN,
109 LP3972_OVER2_LDO2_EN,
110 LP3972_OVER2_LDO3_EN,
111 LP3972_OVER2_LDO4_EN,
112 LP3972_OVER1_S_EN,
113 };
114
115 static const int ldo_output_enable_addr[] = {
116 LP3972_OEN3_REG,
117 LP3972_OVER2_REG,
118 LP3972_OVER2_REG,
119 LP3972_OVER2_REG,
120 LP3972_OVER1_REG,
121 };
122
123 static const int ldo_vol_ctl_addr[] = {
124 LP3972_MDTV1_REG,
125 LP3972_L2VCR_REG,
126 LP3972_L34VCR_REG,
127 LP3972_L34VCR_REG,
128 LP3972_SDTV1_REG,
129 };
130
131 static const int buck_vol_enable_addr[] = {
132 LP3972_OVER1_REG,
133 LP3972_OEN3_REG,
134 LP3972_OEN3_REG,
135 };
136
137 static const int buck_base_addr[] = {
138 LP3972_ADTV1_REG,
139 LP3972_B2TV_REG,
140 LP3972_B3TV_REG,
141 };
142
143 #define LP3972_LDO_OUTPUT_ENABLE_MASK(x) (ldo_output_enable_mask[x])
144 #define LP3972_LDO_OUTPUT_ENABLE_REG(x) (ldo_output_enable_addr[x])
145
146 /* LDO voltage control registers shift:
147 LP3972_LDO1 -> 0, LP3972_LDO2 -> 4
148 LP3972_LDO3 -> 0, LP3972_LDO4 -> 4
149 LP3972_LDO5 -> 0
150 */
151 #define LP3972_LDO_VOL_CONTR_SHIFT(x) (((x) & 1) << 2)
152 #define LP3972_LDO_VOL_CONTR_REG(x) (ldo_vol_ctl_addr[x])
153 #define LP3972_LDO_VOL_CHANGE_SHIFT(x) ((x) ? 4 : 6)
154
155 #define LP3972_LDO_VOL_MASK(x) (((x) % 4) ? 0x0f : 0x1f)
156 #define LP3972_LDO_VOL_MIN_IDX(x) (((x) == 4) ? 0x05 : 0x00)
157 #define LP3972_LDO_VOL_MAX_IDX(x) ((x) ? (((x) == 4) ? 0x1f : 0x0f) : 0x0c)
158
159 #define LP3972_BUCK_VOL_ENABLE_REG(x) (buck_vol_enable_addr[x])
160 #define LP3972_BUCK_VOL1_REG(x) (buck_base_addr[x])
161 #define LP3972_BUCK_VOL_MASK 0x1f
162
lp3972_i2c_read(struct i2c_client * i2c,char reg,int count,u16 * dest)163 static int lp3972_i2c_read(struct i2c_client *i2c, char reg, int count,
164 u16 *dest)
165 {
166 int ret;
167
168 if (count != 1)
169 return -EIO;
170 ret = i2c_smbus_read_byte_data(i2c, reg);
171 if (ret < 0)
172 return ret;
173
174 *dest = ret;
175 return 0;
176 }
177
lp3972_i2c_write(struct i2c_client * i2c,char reg,int count,const u16 * src)178 static int lp3972_i2c_write(struct i2c_client *i2c, char reg, int count,
179 const u16 *src)
180 {
181 if (count != 1)
182 return -EIO;
183 return i2c_smbus_write_byte_data(i2c, reg, *src);
184 }
185
lp3972_reg_read(struct lp3972 * lp3972,u8 reg)186 static u8 lp3972_reg_read(struct lp3972 *lp3972, u8 reg)
187 {
188 u16 val = 0;
189
190 mutex_lock(&lp3972->io_lock);
191
192 lp3972_i2c_read(lp3972->i2c, reg, 1, &val);
193
194 dev_dbg(lp3972->dev, "reg read 0x%02x -> 0x%02x\n", (int)reg,
195 (unsigned)val & 0xff);
196
197 mutex_unlock(&lp3972->io_lock);
198
199 return val & 0xff;
200 }
201
lp3972_set_bits(struct lp3972 * lp3972,u8 reg,u16 mask,u16 val)202 static int lp3972_set_bits(struct lp3972 *lp3972, u8 reg, u16 mask, u16 val)
203 {
204 u16 tmp;
205 int ret;
206
207 mutex_lock(&lp3972->io_lock);
208
209 ret = lp3972_i2c_read(lp3972->i2c, reg, 1, &tmp);
210 if (ret == 0) {
211 tmp = (tmp & ~mask) | val;
212 ret = lp3972_i2c_write(lp3972->i2c, reg, 1, &tmp);
213 dev_dbg(lp3972->dev, "reg write 0x%02x -> 0x%02x\n", (int)reg,
214 (unsigned)val & 0xff);
215 }
216 mutex_unlock(&lp3972->io_lock);
217
218 return ret;
219 }
220
lp3972_ldo_is_enabled(struct regulator_dev * dev)221 static int lp3972_ldo_is_enabled(struct regulator_dev *dev)
222 {
223 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
224 int ldo = rdev_get_id(dev) - LP3972_LDO1;
225 u16 mask = LP3972_LDO_OUTPUT_ENABLE_MASK(ldo);
226 u16 val;
227
228 val = lp3972_reg_read(lp3972, LP3972_LDO_OUTPUT_ENABLE_REG(ldo));
229 return !!(val & mask);
230 }
231
lp3972_ldo_enable(struct regulator_dev * dev)232 static int lp3972_ldo_enable(struct regulator_dev *dev)
233 {
234 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
235 int ldo = rdev_get_id(dev) - LP3972_LDO1;
236 u16 mask = LP3972_LDO_OUTPUT_ENABLE_MASK(ldo);
237
238 return lp3972_set_bits(lp3972, LP3972_LDO_OUTPUT_ENABLE_REG(ldo),
239 mask, mask);
240 }
241
lp3972_ldo_disable(struct regulator_dev * dev)242 static int lp3972_ldo_disable(struct regulator_dev *dev)
243 {
244 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
245 int ldo = rdev_get_id(dev) - LP3972_LDO1;
246 u16 mask = LP3972_LDO_OUTPUT_ENABLE_MASK(ldo);
247
248 return lp3972_set_bits(lp3972, LP3972_LDO_OUTPUT_ENABLE_REG(ldo),
249 mask, 0);
250 }
251
lp3972_ldo_get_voltage_sel(struct regulator_dev * dev)252 static int lp3972_ldo_get_voltage_sel(struct regulator_dev *dev)
253 {
254 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
255 int ldo = rdev_get_id(dev) - LP3972_LDO1;
256 u16 mask = LP3972_LDO_VOL_MASK(ldo);
257 u16 val, reg;
258
259 reg = lp3972_reg_read(lp3972, LP3972_LDO_VOL_CONTR_REG(ldo));
260 val = (reg >> LP3972_LDO_VOL_CONTR_SHIFT(ldo)) & mask;
261
262 return val;
263 }
264
lp3972_ldo_set_voltage_sel(struct regulator_dev * dev,unsigned int selector)265 static int lp3972_ldo_set_voltage_sel(struct regulator_dev *dev,
266 unsigned int selector)
267 {
268 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
269 int ldo = rdev_get_id(dev) - LP3972_LDO1;
270 int shift, ret;
271
272 shift = LP3972_LDO_VOL_CONTR_SHIFT(ldo);
273 ret = lp3972_set_bits(lp3972, LP3972_LDO_VOL_CONTR_REG(ldo),
274 LP3972_LDO_VOL_MASK(ldo) << shift, selector << shift);
275
276 if (ret)
277 return ret;
278
279 /*
280 * LDO1 and LDO5 support voltage control by either target voltage1
281 * or target voltage2 register.
282 * We use target voltage1 register for LDO1 and LDO5 in this driver.
283 * We need to update voltage change control register(0x20) to enable
284 * LDO1 and LDO5 to change to their programmed target values.
285 */
286 switch (ldo) {
287 case LP3972_LDO1:
288 case LP3972_LDO5:
289 shift = LP3972_LDO_VOL_CHANGE_SHIFT(ldo);
290 ret = lp3972_set_bits(lp3972, LP3972_VOL_CHANGE_REG,
291 LP3972_VOL_CHANGE_FLAG_MASK << shift,
292 LP3972_VOL_CHANGE_FLAG_GO << shift);
293 if (ret)
294 return ret;
295
296 ret = lp3972_set_bits(lp3972, LP3972_VOL_CHANGE_REG,
297 LP3972_VOL_CHANGE_FLAG_MASK << shift, 0);
298 break;
299 }
300
301 return ret;
302 }
303
304 static const struct regulator_ops lp3972_ldo_ops = {
305 .list_voltage = regulator_list_voltage_table,
306 .map_voltage = regulator_map_voltage_ascend,
307 .is_enabled = lp3972_ldo_is_enabled,
308 .enable = lp3972_ldo_enable,
309 .disable = lp3972_ldo_disable,
310 .get_voltage_sel = lp3972_ldo_get_voltage_sel,
311 .set_voltage_sel = lp3972_ldo_set_voltage_sel,
312 };
313
lp3972_dcdc_is_enabled(struct regulator_dev * dev)314 static int lp3972_dcdc_is_enabled(struct regulator_dev *dev)
315 {
316 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
317 int buck = rdev_get_id(dev) - LP3972_DCDC1;
318 u16 mask = 1 << (buck * 2);
319 u16 val;
320
321 val = lp3972_reg_read(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck));
322 return !!(val & mask);
323 }
324
lp3972_dcdc_enable(struct regulator_dev * dev)325 static int lp3972_dcdc_enable(struct regulator_dev *dev)
326 {
327 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
328 int buck = rdev_get_id(dev) - LP3972_DCDC1;
329 u16 mask = 1 << (buck * 2);
330 u16 val;
331
332 val = lp3972_set_bits(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck),
333 mask, mask);
334 return val;
335 }
336
lp3972_dcdc_disable(struct regulator_dev * dev)337 static int lp3972_dcdc_disable(struct regulator_dev *dev)
338 {
339 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
340 int buck = rdev_get_id(dev) - LP3972_DCDC1;
341 u16 mask = 1 << (buck * 2);
342 u16 val;
343
344 val = lp3972_set_bits(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck),
345 mask, 0);
346 return val;
347 }
348
lp3972_dcdc_get_voltage_sel(struct regulator_dev * dev)349 static int lp3972_dcdc_get_voltage_sel(struct regulator_dev *dev)
350 {
351 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
352 int buck = rdev_get_id(dev) - LP3972_DCDC1;
353 u16 reg;
354
355 reg = lp3972_reg_read(lp3972, LP3972_BUCK_VOL1_REG(buck));
356 reg &= LP3972_BUCK_VOL_MASK;
357
358 return reg;
359 }
360
lp3972_dcdc_set_voltage_sel(struct regulator_dev * dev,unsigned int selector)361 static int lp3972_dcdc_set_voltage_sel(struct regulator_dev *dev,
362 unsigned int selector)
363 {
364 struct lp3972 *lp3972 = rdev_get_drvdata(dev);
365 int buck = rdev_get_id(dev) - LP3972_DCDC1;
366 int ret;
367
368 ret = lp3972_set_bits(lp3972, LP3972_BUCK_VOL1_REG(buck),
369 LP3972_BUCK_VOL_MASK, selector);
370 if (ret)
371 return ret;
372
373 if (buck != 0)
374 return ret;
375
376 ret = lp3972_set_bits(lp3972, LP3972_VOL_CHANGE_REG,
377 LP3972_VOL_CHANGE_FLAG_MASK, LP3972_VOL_CHANGE_FLAG_GO);
378 if (ret)
379 return ret;
380
381 return lp3972_set_bits(lp3972, LP3972_VOL_CHANGE_REG,
382 LP3972_VOL_CHANGE_FLAG_MASK, 0);
383 }
384
385 static const struct regulator_ops lp3972_dcdc_ops = {
386 .list_voltage = regulator_list_voltage_table,
387 .map_voltage = regulator_map_voltage_ascend,
388 .is_enabled = lp3972_dcdc_is_enabled,
389 .enable = lp3972_dcdc_enable,
390 .disable = lp3972_dcdc_disable,
391 .get_voltage_sel = lp3972_dcdc_get_voltage_sel,
392 .set_voltage_sel = lp3972_dcdc_set_voltage_sel,
393 };
394
395 static const struct regulator_desc regulators[] = {
396 {
397 .name = "LDO1",
398 .id = LP3972_LDO1,
399 .ops = &lp3972_ldo_ops,
400 .n_voltages = ARRAY_SIZE(ldo1_voltage_map),
401 .volt_table = ldo1_voltage_map,
402 .type = REGULATOR_VOLTAGE,
403 .owner = THIS_MODULE,
404 },
405 {
406 .name = "LDO2",
407 .id = LP3972_LDO2,
408 .ops = &lp3972_ldo_ops,
409 .n_voltages = ARRAY_SIZE(ldo23_voltage_map),
410 .volt_table = ldo23_voltage_map,
411 .type = REGULATOR_VOLTAGE,
412 .owner = THIS_MODULE,
413 },
414 {
415 .name = "LDO3",
416 .id = LP3972_LDO3,
417 .ops = &lp3972_ldo_ops,
418 .n_voltages = ARRAY_SIZE(ldo23_voltage_map),
419 .volt_table = ldo23_voltage_map,
420 .type = REGULATOR_VOLTAGE,
421 .owner = THIS_MODULE,
422 },
423 {
424 .name = "LDO4",
425 .id = LP3972_LDO4,
426 .ops = &lp3972_ldo_ops,
427 .n_voltages = ARRAY_SIZE(ldo4_voltage_map),
428 .volt_table = ldo4_voltage_map,
429 .type = REGULATOR_VOLTAGE,
430 .owner = THIS_MODULE,
431 },
432 {
433 .name = "LDO5",
434 .id = LP3972_LDO5,
435 .ops = &lp3972_ldo_ops,
436 .n_voltages = ARRAY_SIZE(ldo5_voltage_map),
437 .volt_table = ldo5_voltage_map,
438 .type = REGULATOR_VOLTAGE,
439 .owner = THIS_MODULE,
440 },
441 {
442 .name = "DCDC1",
443 .id = LP3972_DCDC1,
444 .ops = &lp3972_dcdc_ops,
445 .n_voltages = ARRAY_SIZE(buck1_voltage_map),
446 .volt_table = buck1_voltage_map,
447 .type = REGULATOR_VOLTAGE,
448 .owner = THIS_MODULE,
449 },
450 {
451 .name = "DCDC2",
452 .id = LP3972_DCDC2,
453 .ops = &lp3972_dcdc_ops,
454 .n_voltages = ARRAY_SIZE(buck23_voltage_map),
455 .volt_table = buck23_voltage_map,
456 .type = REGULATOR_VOLTAGE,
457 .owner = THIS_MODULE,
458 },
459 {
460 .name = "DCDC3",
461 .id = LP3972_DCDC3,
462 .ops = &lp3972_dcdc_ops,
463 .n_voltages = ARRAY_SIZE(buck23_voltage_map),
464 .volt_table = buck23_voltage_map,
465 .type = REGULATOR_VOLTAGE,
466 .owner = THIS_MODULE,
467 },
468 };
469
setup_regulators(struct lp3972 * lp3972,struct lp3972_platform_data * pdata)470 static int setup_regulators(struct lp3972 *lp3972,
471 struct lp3972_platform_data *pdata)
472 {
473 int i, err;
474
475 /* Instantiate the regulators */
476 for (i = 0; i < pdata->num_regulators; i++) {
477 struct lp3972_regulator_subdev *reg = &pdata->regulators[i];
478 struct regulator_config config = { };
479 struct regulator_dev *rdev;
480
481 config.dev = lp3972->dev;
482 config.init_data = reg->initdata;
483 config.driver_data = lp3972;
484
485 rdev = devm_regulator_register(lp3972->dev,
486 ®ulators[reg->id], &config);
487 if (IS_ERR(rdev)) {
488 err = PTR_ERR(rdev);
489 dev_err(lp3972->dev, "regulator init failed: %d\n",
490 err);
491 return err;
492 }
493 }
494
495 return 0;
496 }
497
lp3972_i2c_probe(struct i2c_client * i2c,const struct i2c_device_id * id)498 static int lp3972_i2c_probe(struct i2c_client *i2c,
499 const struct i2c_device_id *id)
500 {
501 struct lp3972 *lp3972;
502 struct lp3972_platform_data *pdata = dev_get_platdata(&i2c->dev);
503 int ret;
504 u16 val;
505
506 if (!pdata) {
507 dev_dbg(&i2c->dev, "No platform init data supplied\n");
508 return -ENODEV;
509 }
510
511 lp3972 = devm_kzalloc(&i2c->dev, sizeof(struct lp3972), GFP_KERNEL);
512 if (!lp3972)
513 return -ENOMEM;
514
515 lp3972->i2c = i2c;
516 lp3972->dev = &i2c->dev;
517
518 mutex_init(&lp3972->io_lock);
519
520 /* Detect LP3972 */
521 ret = lp3972_i2c_read(i2c, LP3972_SYS_CONTROL1_REG, 1, &val);
522 if (ret == 0 &&
523 (val & SYS_CONTROL1_INIT_MASK) != SYS_CONTROL1_INIT_VAL) {
524 ret = -ENODEV;
525 dev_err(&i2c->dev, "chip reported: val = 0x%x\n", val);
526 }
527 if (ret < 0) {
528 dev_err(&i2c->dev, "failed to detect device. ret = %d\n", ret);
529 return ret;
530 }
531
532 ret = setup_regulators(lp3972, pdata);
533 if (ret < 0)
534 return ret;
535
536 i2c_set_clientdata(i2c, lp3972);
537 return 0;
538 }
539
540 static const struct i2c_device_id lp3972_i2c_id[] = {
541 { "lp3972", 0 },
542 { }
543 };
544 MODULE_DEVICE_TABLE(i2c, lp3972_i2c_id);
545
546 static struct i2c_driver lp3972_i2c_driver = {
547 .driver = {
548 .name = "lp3972",
549 },
550 .probe = lp3972_i2c_probe,
551 .id_table = lp3972_i2c_id,
552 };
553
lp3972_module_init(void)554 static int __init lp3972_module_init(void)
555 {
556 return i2c_add_driver(&lp3972_i2c_driver);
557 }
558 subsys_initcall(lp3972_module_init);
559
lp3972_module_exit(void)560 static void __exit lp3972_module_exit(void)
561 {
562 i2c_del_driver(&lp3972_i2c_driver);
563 }
564 module_exit(lp3972_module_exit);
565
566 MODULE_LICENSE("GPL");
567 MODULE_AUTHOR("Axel Lin <axel.lin@gmail.com>");
568 MODULE_DESCRIPTION("LP3972 PMIC driver");
569