1 // SPDX-License-Identifier: GPL-2.0
2 /******************************************************************************
3 *
4 * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
5 *
6 ******************************************************************************/
7 #define _HCI_HAL_INIT_C_
8
9 #include <osdep_service.h>
10 #include <drv_types.h>
11 #include <rtw_efuse.h>
12 #include <fw.h>
13 #include <rtl8188e_hal.h>
14 #include <phy.h>
15
16 #define HAL_BB_ENABLE 1
17
_ConfigNormalChipOutEP_8188E(struct adapter * adapt,u8 NumOutPipe)18 static void _ConfigNormalChipOutEP_8188E(struct adapter *adapt, u8 NumOutPipe)
19 {
20 struct hal_data_8188e *haldata = adapt->HalData;
21
22 switch (NumOutPipe) {
23 case 3:
24 haldata->OutEpQueueSel = TX_SELE_HQ | TX_SELE_LQ | TX_SELE_NQ;
25 haldata->OutEpNumber = 3;
26 break;
27 case 2:
28 haldata->OutEpQueueSel = TX_SELE_HQ | TX_SELE_NQ;
29 haldata->OutEpNumber = 2;
30 break;
31 case 1:
32 haldata->OutEpQueueSel = TX_SELE_HQ;
33 haldata->OutEpNumber = 1;
34 break;
35 default:
36 break;
37 }
38 DBG_88E("%s OutEpQueueSel(0x%02x), OutEpNumber(%d)\n", __func__, haldata->OutEpQueueSel, haldata->OutEpNumber);
39 }
40
HalUsbSetQueuePipeMapping8188EUsb(struct adapter * adapt,u8 NumInPipe,u8 NumOutPipe)41 static bool HalUsbSetQueuePipeMapping8188EUsb(struct adapter *adapt, u8 NumInPipe, u8 NumOutPipe)
42 {
43 bool result = false;
44
45 _ConfigNormalChipOutEP_8188E(adapt, NumOutPipe);
46
47 /* Normal chip with one IN and one OUT doesn't have interrupt IN EP. */
48 if (adapt->HalData->OutEpNumber == 1) {
49 if (NumInPipe != 1)
50 return result;
51 }
52
53 /* All config other than above support one Bulk IN and one Interrupt IN. */
54
55 result = hal_mapping_out_pipe(adapt, NumOutPipe);
56
57 return result;
58 }
59
rtw_hal_chip_configure(struct adapter * adapt)60 void rtw_hal_chip_configure(struct adapter *adapt)
61 {
62 struct hal_data_8188e *haldata = adapt->HalData;
63 struct dvobj_priv *pdvobjpriv = adapter_to_dvobj(adapt);
64
65 if (pdvobjpriv->ishighspeed)
66 haldata->UsbBulkOutSize = USB_HIGH_SPEED_BULK_SIZE;/* 512 bytes */
67 else
68 haldata->UsbBulkOutSize = USB_FULL_SPEED_BULK_SIZE;/* 64 bytes */
69
70 haldata->interfaceIndex = pdvobjpriv->InterfaceNumber;
71
72 haldata->UsbTxAggMode = 1;
73 haldata->UsbTxAggDescNum = 0x6; /* only 4 bits */
74
75 haldata->UsbRxAggMode = USB_RX_AGG_DMA;/* USB_RX_AGG_DMA; */
76 haldata->UsbRxAggBlockCount = 8; /* unit : 512b */
77 haldata->UsbRxAggBlockTimeout = 0x6;
78 haldata->UsbRxAggPageCount = 48; /* uint :128 b 0x0A; 10 = MAX_RX_DMA_BUFFER_SIZE/2/haldata->UsbBulkOutSize */
79 haldata->UsbRxAggPageTimeout = 0x4; /* 6, absolute time = 34ms/(2^6) */
80
81 HalUsbSetQueuePipeMapping8188EUsb(adapt,
82 pdvobjpriv->RtNumInPipes, pdvobjpriv->RtNumOutPipes);
83 }
84
rtw_hal_power_on(struct adapter * adapt)85 u32 rtw_hal_power_on(struct adapter *adapt)
86 {
87 u16 value16;
88 /* HW Power on sequence */
89 if (adapt->HalData->bMacPwrCtrlOn)
90 return _SUCCESS;
91
92 if (!rtl88eu_pwrseqcmdparsing(adapt, PWR_CUT_ALL_MSK,
93 Rtl8188E_NIC_PWR_ON_FLOW)) {
94 DBG_88E(KERN_ERR "%s: run power on flow fail\n", __func__);
95 return _FAIL;
96 }
97
98 /* Enable MAC DMA/WMAC/SCHEDULE/SEC block */
99 /* Set CR bit10 to enable 32k calibration. Suggested by SD1 Gimmy. Added by tynli. 2011.08.31. */
100 usb_write16(adapt, REG_CR, 0x00); /* suggseted by zhouzhou, by page, 20111230 */
101
102 /* Enable MAC DMA/WMAC/SCHEDULE/SEC block */
103 value16 = usb_read16(adapt, REG_CR);
104 value16 |= (HCI_TXDMA_EN | HCI_RXDMA_EN | TXDMA_EN | RXDMA_EN
105 | PROTOCOL_EN | SCHEDULE_EN | ENSEC | CALTMR_EN);
106 /* for SDIO - Set CR bit10 to enable 32k calibration. Suggested by SD1 Gimmy. Added by tynli. 2011.08.31. */
107
108 usb_write16(adapt, REG_CR, value16);
109 adapt->HalData->bMacPwrCtrlOn = true;
110
111 return _SUCCESS;
112 }
113
114 /* Shall USB interface init this? */
_InitInterrupt(struct adapter * Adapter)115 static void _InitInterrupt(struct adapter *Adapter)
116 {
117 u32 imr, imr_ex;
118 u8 usb_opt;
119
120 /* HISR write one to clear */
121 usb_write32(Adapter, REG_HISR_88E, 0xFFFFFFFF);
122 /* HIMR - */
123 imr = IMR_PSTIMEOUT_88E | IMR_TBDER_88E | IMR_CPWM_88E | IMR_CPWM2_88E;
124 usb_write32(Adapter, REG_HIMR_88E, imr);
125 Adapter->HalData->IntrMask[0] = imr;
126
127 imr_ex = IMR_TXERR_88E | IMR_RXERR_88E | IMR_TXFOVW_88E | IMR_RXFOVW_88E;
128 usb_write32(Adapter, REG_HIMRE_88E, imr_ex);
129 Adapter->HalData->IntrMask[1] = imr_ex;
130
131 /* REG_USB_SPECIAL_OPTION - BIT(4) */
132 /* 0; Use interrupt endpoint to upload interrupt pkt */
133 /* 1; Use bulk endpoint to upload interrupt pkt, */
134 usb_opt = usb_read8(Adapter, REG_USB_SPECIAL_OPTION);
135
136 if (!adapter_to_dvobj(Adapter)->ishighspeed)
137 usb_opt = usb_opt & (~INT_BULK_SEL);
138 else
139 usb_opt = usb_opt | (INT_BULK_SEL);
140
141 usb_write8(Adapter, REG_USB_SPECIAL_OPTION, usb_opt);
142 }
143
_InitQueueReservedPage(struct adapter * Adapter)144 static void _InitQueueReservedPage(struct adapter *Adapter)
145 {
146 struct registry_priv *pregistrypriv = &Adapter->registrypriv;
147 u32 numHQ = 0;
148 u32 numLQ = 0;
149 u32 numNQ = 0;
150 u32 numPubQ;
151 u32 value32;
152 u8 value8;
153 bool bWiFiConfig = pregistrypriv->wifi_spec;
154
155 if (bWiFiConfig) {
156 if (Adapter->HalData->OutEpQueueSel & TX_SELE_HQ)
157 numHQ = 0x29;
158
159 if (Adapter->HalData->OutEpQueueSel & TX_SELE_LQ)
160 numLQ = 0x1C;
161
162 /* NOTE: This step shall be proceed before writing REG_RQPN. */
163 if (Adapter->HalData->OutEpQueueSel & TX_SELE_NQ)
164 numNQ = 0x1C;
165 value8 = (u8)_NPQ(numNQ);
166 usb_write8(Adapter, REG_RQPN_NPQ, value8);
167
168 numPubQ = 0xA8 - numHQ - numLQ - numNQ;
169
170 /* TX DMA */
171 value32 = _HPQ(numHQ) | _LPQ(numLQ) | _PUBQ(numPubQ) | LD_RQPN;
172 usb_write32(Adapter, REG_RQPN, value32);
173 } else {
174 usb_write16(Adapter, REG_RQPN_NPQ, 0x0000);/* Just follow MP Team,??? Georgia 03/28 */
175 usb_write16(Adapter, REG_RQPN_NPQ, 0x0d);
176 usb_write32(Adapter, REG_RQPN, 0x808E000d);/* reserve 7 page for LPS */
177 }
178 }
179
_InitTxBufferBoundary(struct adapter * Adapter,u8 txpktbuf_bndy)180 static void _InitTxBufferBoundary(struct adapter *Adapter, u8 txpktbuf_bndy)
181 {
182 usb_write8(Adapter, REG_TXPKTBUF_BCNQ_BDNY, txpktbuf_bndy);
183 usb_write8(Adapter, REG_TXPKTBUF_MGQ_BDNY, txpktbuf_bndy);
184 usb_write8(Adapter, REG_TXPKTBUF_WMAC_LBK_BF_HD, txpktbuf_bndy);
185 usb_write8(Adapter, REG_TRXFF_BNDY, txpktbuf_bndy);
186 usb_write8(Adapter, REG_TDECTRL + 1, txpktbuf_bndy);
187 }
188
_InitPageBoundary(struct adapter * Adapter)189 static void _InitPageBoundary(struct adapter *Adapter)
190 {
191 /* RX Page Boundary */
192 /* */
193 u16 rxff_bndy = MAX_RX_DMA_BUFFER_SIZE_88E - 1;
194
195 usb_write16(Adapter, (REG_TRXFF_BNDY + 2), rxff_bndy);
196 }
197
_InitNormalChipRegPriority(struct adapter * Adapter,u16 beQ,u16 bkQ,u16 viQ,u16 voQ,u16 mgtQ,u16 hiQ)198 static void _InitNormalChipRegPriority(struct adapter *Adapter, u16 beQ,
199 u16 bkQ, u16 viQ, u16 voQ, u16 mgtQ,
200 u16 hiQ)
201 {
202 u16 value16 = (usb_read16(Adapter, REG_TRXDMA_CTRL) & 0x7);
203
204 value16 |= _TXDMA_BEQ_MAP(beQ) | _TXDMA_BKQ_MAP(bkQ) |
205 _TXDMA_VIQ_MAP(viQ) | _TXDMA_VOQ_MAP(voQ) |
206 _TXDMA_MGQ_MAP(mgtQ) | _TXDMA_HIQ_MAP(hiQ);
207
208 usb_write16(Adapter, REG_TRXDMA_CTRL, value16);
209 }
210
_InitNormalChipOneOutEpPriority(struct adapter * Adapter)211 static void _InitNormalChipOneOutEpPriority(struct adapter *Adapter)
212 {
213 u16 value = 0;
214
215 switch (Adapter->HalData->OutEpQueueSel) {
216 case TX_SELE_HQ:
217 value = QUEUE_HIGH;
218 break;
219 case TX_SELE_LQ:
220 value = QUEUE_LOW;
221 break;
222 case TX_SELE_NQ:
223 value = QUEUE_NORMAL;
224 break;
225 default:
226 break;
227 }
228 _InitNormalChipRegPriority(Adapter, value, value, value, value,
229 value, value);
230 }
231
_InitNormalChipTwoOutEpPriority(struct adapter * Adapter)232 static void _InitNormalChipTwoOutEpPriority(struct adapter *Adapter)
233 {
234 struct registry_priv *pregistrypriv = &Adapter->registrypriv;
235 u16 beQ, bkQ, viQ, voQ, mgtQ, hiQ;
236 u16 valueHi = 0;
237 u16 valueLow = 0;
238
239 switch (Adapter->HalData->OutEpQueueSel) {
240 case (TX_SELE_HQ | TX_SELE_LQ):
241 valueHi = QUEUE_HIGH;
242 valueLow = QUEUE_LOW;
243 break;
244 case (TX_SELE_NQ | TX_SELE_LQ):
245 valueHi = QUEUE_NORMAL;
246 valueLow = QUEUE_LOW;
247 break;
248 case (TX_SELE_HQ | TX_SELE_NQ):
249 valueHi = QUEUE_HIGH;
250 valueLow = QUEUE_NORMAL;
251 break;
252 default:
253 break;
254 }
255
256 if (!pregistrypriv->wifi_spec) {
257 beQ = valueLow;
258 bkQ = valueLow;
259 viQ = valueHi;
260 voQ = valueHi;
261 mgtQ = valueHi;
262 hiQ = valueHi;
263 } else {/* for WMM ,CONFIG_OUT_EP_WIFI_MODE */
264 beQ = valueLow;
265 bkQ = valueHi;
266 viQ = valueHi;
267 voQ = valueLow;
268 mgtQ = valueHi;
269 hiQ = valueHi;
270 }
271 _InitNormalChipRegPriority(Adapter, beQ, bkQ, viQ, voQ, mgtQ, hiQ);
272 }
273
_InitNormalChipThreeOutEpPriority(struct adapter * Adapter)274 static void _InitNormalChipThreeOutEpPriority(struct adapter *Adapter)
275 {
276 struct registry_priv *pregistrypriv = &Adapter->registrypriv;
277 u16 beQ, bkQ, viQ, voQ, mgtQ, hiQ;
278
279 if (!pregistrypriv->wifi_spec) {/* typical setting */
280 beQ = QUEUE_LOW;
281 bkQ = QUEUE_LOW;
282 viQ = QUEUE_NORMAL;
283 voQ = QUEUE_HIGH;
284 mgtQ = QUEUE_HIGH;
285 hiQ = QUEUE_HIGH;
286 } else {/* for WMM */
287 beQ = QUEUE_LOW;
288 bkQ = QUEUE_NORMAL;
289 viQ = QUEUE_NORMAL;
290 voQ = QUEUE_HIGH;
291 mgtQ = QUEUE_HIGH;
292 hiQ = QUEUE_HIGH;
293 }
294 _InitNormalChipRegPriority(Adapter, beQ, bkQ, viQ, voQ, mgtQ, hiQ);
295 }
296
_InitQueuePriority(struct adapter * Adapter)297 static void _InitQueuePriority(struct adapter *Adapter)
298 {
299 switch (Adapter->HalData->OutEpNumber) {
300 case 1:
301 _InitNormalChipOneOutEpPriority(Adapter);
302 break;
303 case 2:
304 _InitNormalChipTwoOutEpPriority(Adapter);
305 break;
306 case 3:
307 _InitNormalChipThreeOutEpPriority(Adapter);
308 break;
309 default:
310 break;
311 }
312 }
313
_InitNetworkType(struct adapter * Adapter)314 static void _InitNetworkType(struct adapter *Adapter)
315 {
316 u32 value32;
317
318 value32 = usb_read32(Adapter, REG_CR);
319 /* TODO: use the other function to set network type */
320 value32 = (value32 & ~MASK_NETTYPE) | _NETTYPE(NT_LINK_AP);
321
322 usb_write32(Adapter, REG_CR, value32);
323 }
324
_InitTransferPageSize(struct adapter * Adapter)325 static void _InitTransferPageSize(struct adapter *Adapter)
326 {
327 /* Tx page size is always 128. */
328
329 u8 value8;
330
331 value8 = _PSRX(PBP_128) | _PSTX(PBP_128);
332 usb_write8(Adapter, REG_PBP, value8);
333 }
334
_InitDriverInfoSize(struct adapter * Adapter,u8 drvInfoSize)335 static void _InitDriverInfoSize(struct adapter *Adapter, u8 drvInfoSize)
336 {
337 usb_write8(Adapter, REG_RX_DRVINFO_SZ, drvInfoSize);
338 }
339
_InitWMACSetting(struct adapter * Adapter)340 static void _InitWMACSetting(struct adapter *Adapter)
341 {
342 struct hal_data_8188e *haldata = Adapter->HalData;
343
344 haldata->ReceiveConfig = RCR_AAP | RCR_APM | RCR_AM | RCR_AB |
345 RCR_CBSSID_DATA | RCR_CBSSID_BCN |
346 RCR_APP_ICV | RCR_AMF | RCR_HTC_LOC_CTRL |
347 RCR_APP_MIC | RCR_APP_PHYSTS;
348
349 /* some REG_RCR will be modified later by phy_ConfigMACWithHeaderFile() */
350 usb_write32(Adapter, REG_RCR, haldata->ReceiveConfig);
351
352 /* Accept all multicast address */
353 usb_write32(Adapter, REG_MAR, 0xFFFFFFFF);
354 usb_write32(Adapter, REG_MAR + 4, 0xFFFFFFFF);
355 }
356
_InitAdaptiveCtrl(struct adapter * Adapter)357 static void _InitAdaptiveCtrl(struct adapter *Adapter)
358 {
359 u16 value16;
360 u32 value32;
361
362 /* Response Rate Set */
363 value32 = usb_read32(Adapter, REG_RRSR);
364 value32 &= ~RATE_BITMAP_ALL;
365 value32 |= RATE_RRSR_CCK_ONLY_1M;
366 usb_write32(Adapter, REG_RRSR, value32);
367
368 /* CF-END Threshold */
369
370 /* SIFS (used in NAV) */
371 value16 = _SPEC_SIFS_CCK(0x10) | _SPEC_SIFS_OFDM(0x10);
372 usb_write16(Adapter, REG_SPEC_SIFS, value16);
373
374 /* Retry Limit */
375 value16 = _LRL(0x30) | _SRL(0x30);
376 usb_write16(Adapter, REG_RL, value16);
377 }
378
_InitEDCA(struct adapter * Adapter)379 static void _InitEDCA(struct adapter *Adapter)
380 {
381 /* Set Spec SIFS (used in NAV) */
382 usb_write16(Adapter, REG_SPEC_SIFS, 0x100a);
383 usb_write16(Adapter, REG_MAC_SPEC_SIFS, 0x100a);
384
385 /* Set SIFS for CCK */
386 usb_write16(Adapter, REG_SIFS_CTX, 0x100a);
387
388 /* Set SIFS for OFDM */
389 usb_write16(Adapter, REG_SIFS_TRX, 0x100a);
390
391 /* TXOP */
392 usb_write32(Adapter, REG_EDCA_BE_PARAM, 0x005EA42B);
393 usb_write32(Adapter, REG_EDCA_BK_PARAM, 0x0000A44F);
394 usb_write32(Adapter, REG_EDCA_VI_PARAM, 0x005EA324);
395 usb_write32(Adapter, REG_EDCA_VO_PARAM, 0x002FA226);
396 }
397
_InitRDGSetting(struct adapter * Adapter)398 static void _InitRDGSetting(struct adapter *Adapter)
399 {
400 usb_write8(Adapter, REG_RD_CTRL, 0xFF);
401 usb_write16(Adapter, REG_RD_NAV_NXT, 0x200);
402 usb_write8(Adapter, REG_RD_RESP_PKT_TH, 0x05);
403 }
404
_InitRxSetting(struct adapter * Adapter)405 static void _InitRxSetting(struct adapter *Adapter)
406 {
407 usb_write32(Adapter, REG_MACID, 0x87654321);
408 usb_write32(Adapter, 0x0700, 0x87654321);
409 }
410
_InitRetryFunction(struct adapter * Adapter)411 static void _InitRetryFunction(struct adapter *Adapter)
412 {
413 u8 value8;
414
415 value8 = usb_read8(Adapter, REG_FWHW_TXQ_CTRL);
416 value8 |= EN_AMPDU_RTY_NEW;
417 usb_write8(Adapter, REG_FWHW_TXQ_CTRL, value8);
418
419 /* Set ACK timeout */
420 usb_write8(Adapter, REG_ACKTO, 0x40);
421 }
422
423 /*-----------------------------------------------------------------------------
424 * Function: usb_AggSettingTxUpdate()
425 *
426 * Overview: Separate TX/RX parameters update independent for TP detection and
427 * dynamic TX/RX aggreagtion parameters update.
428 *
429 * Input: struct adapter *
430 *
431 * Output/Return: NONE
432 *
433 * Revised History:
434 * When Who Remark
435 * 12/10/2010 MHC Separate to smaller function.
436 *
437 *---------------------------------------------------------------------------
438 */
usb_AggSettingTxUpdate(struct adapter * Adapter)439 static void usb_AggSettingTxUpdate(struct adapter *Adapter)
440 {
441 struct hal_data_8188e *haldata = Adapter->HalData;
442 u32 value32;
443
444 if (Adapter->registrypriv.wifi_spec)
445 haldata->UsbTxAggMode = false;
446
447 if (haldata->UsbTxAggMode) {
448 value32 = usb_read32(Adapter, REG_TDECTRL);
449 value32 = value32 & ~(BLK_DESC_NUM_MASK << BLK_DESC_NUM_SHIFT);
450 value32 |= ((haldata->UsbTxAggDescNum & BLK_DESC_NUM_MASK) << BLK_DESC_NUM_SHIFT);
451
452 usb_write32(Adapter, REG_TDECTRL, value32);
453 }
454 } /* usb_AggSettingTxUpdate */
455
456 /*-----------------------------------------------------------------------------
457 * Function: usb_AggSettingRxUpdate()
458 *
459 * Overview: Separate TX/RX parameters update independent for TP detection and
460 * dynamic TX/RX aggreagtion parameters update.
461 *
462 * Input: struct adapter *
463 *
464 * Output/Return: NONE
465 *
466 * Revised History:
467 * When Who Remark
468 * 12/10/2010 MHC Separate to smaller function.
469 *
470 *---------------------------------------------------------------------------
471 */
usb_AggSettingRxUpdate(struct adapter * Adapter)472 static void usb_AggSettingRxUpdate(struct adapter *Adapter)
473 {
474 struct hal_data_8188e *haldata = Adapter->HalData;
475 u8 valueDMA;
476 u8 valueUSB;
477
478 valueDMA = usb_read8(Adapter, REG_TRXDMA_CTRL);
479 valueUSB = usb_read8(Adapter, REG_USB_SPECIAL_OPTION);
480
481 switch (haldata->UsbRxAggMode) {
482 case USB_RX_AGG_DMA:
483 valueDMA |= RXDMA_AGG_EN;
484 valueUSB &= ~USB_AGG_EN;
485 break;
486 case USB_RX_AGG_USB:
487 valueDMA &= ~RXDMA_AGG_EN;
488 valueUSB |= USB_AGG_EN;
489 break;
490 case USB_RX_AGG_MIX:
491 valueDMA |= RXDMA_AGG_EN;
492 valueUSB |= USB_AGG_EN;
493 break;
494 case USB_RX_AGG_DISABLE:
495 default:
496 valueDMA &= ~RXDMA_AGG_EN;
497 valueUSB &= ~USB_AGG_EN;
498 break;
499 }
500
501 usb_write8(Adapter, REG_TRXDMA_CTRL, valueDMA);
502 usb_write8(Adapter, REG_USB_SPECIAL_OPTION, valueUSB);
503
504 switch (haldata->UsbRxAggMode) {
505 case USB_RX_AGG_DMA:
506 usb_write8(Adapter, REG_RXDMA_AGG_PG_TH, haldata->UsbRxAggPageCount);
507 usb_write8(Adapter, REG_RXDMA_AGG_PG_TH + 1, haldata->UsbRxAggPageTimeout);
508 break;
509 case USB_RX_AGG_USB:
510 usb_write8(Adapter, REG_USB_AGG_TH, haldata->UsbRxAggBlockCount);
511 usb_write8(Adapter, REG_USB_AGG_TO, haldata->UsbRxAggBlockTimeout);
512 break;
513 case USB_RX_AGG_MIX:
514 usb_write8(Adapter, REG_RXDMA_AGG_PG_TH, haldata->UsbRxAggPageCount);
515 usb_write8(Adapter, REG_RXDMA_AGG_PG_TH + 1, (haldata->UsbRxAggPageTimeout & 0x1F));/* 0x280[12:8] */
516 usb_write8(Adapter, REG_USB_AGG_TH, haldata->UsbRxAggBlockCount);
517 usb_write8(Adapter, REG_USB_AGG_TO, haldata->UsbRxAggBlockTimeout);
518 break;
519 case USB_RX_AGG_DISABLE:
520 default:
521 /* TODO: */
522 break;
523 }
524
525 switch (PBP_128) {
526 case PBP_128:
527 haldata->HwRxPageSize = 128;
528 break;
529 case PBP_64:
530 haldata->HwRxPageSize = 64;
531 break;
532 case PBP_256:
533 haldata->HwRxPageSize = 256;
534 break;
535 case PBP_512:
536 haldata->HwRxPageSize = 512;
537 break;
538 case PBP_1024:
539 haldata->HwRxPageSize = 1024;
540 break;
541 default:
542 break;
543 }
544 } /* usb_AggSettingRxUpdate */
545
InitUsbAggregationSetting(struct adapter * Adapter)546 static void InitUsbAggregationSetting(struct adapter *Adapter)
547 {
548 /* Tx aggregation setting */
549 usb_AggSettingTxUpdate(Adapter);
550
551 /* Rx aggregation setting */
552 usb_AggSettingRxUpdate(Adapter);
553 }
554
_InitBeaconParameters(struct adapter * Adapter)555 static void _InitBeaconParameters(struct adapter *Adapter)
556 {
557 struct hal_data_8188e *haldata = Adapter->HalData;
558
559 usb_write16(Adapter, REG_BCN_CTRL, 0x1010);
560
561 /* TODO: Remove these magic number */
562 usb_write16(Adapter, REG_TBTT_PROHIBIT, 0x6404);/* ms */
563 usb_write8(Adapter, REG_DRVERLYINT, DRIVER_EARLY_INT_TIME);/* 5ms */
564 usb_write8(Adapter, REG_BCNDMATIM, BCN_DMA_ATIME_INT_TIME); /* 2ms */
565
566 /* Suggested by designer timchen. Change beacon AIFS to the largest number */
567 /* beacause test chip does not contension before sending beacon. by tynli. 2009.11.03 */
568 usb_write16(Adapter, REG_BCNTCFG, 0x660F);
569
570 haldata->RegBcnCtrlVal = usb_read8(Adapter, REG_BCN_CTRL);
571 haldata->RegTxPause = usb_read8(Adapter, REG_TXPAUSE);
572 haldata->RegFwHwTxQCtrl = usb_read8(Adapter, REG_FWHW_TXQ_CTRL + 2);
573 haldata->RegReg542 = usb_read8(Adapter, REG_TBTT_PROHIBIT + 2);
574 haldata->RegCR_1 = usb_read8(Adapter, REG_CR + 1);
575 }
576
_BeaconFunctionEnable(struct adapter * Adapter,bool Enable,bool Linked)577 static void _BeaconFunctionEnable(struct adapter *Adapter,
578 bool Enable, bool Linked)
579 {
580 usb_write8(Adapter, REG_BCN_CTRL, (BIT(4) | BIT(3) | BIT(1)));
581
582 usb_write8(Adapter, REG_RD_CTRL + 1, 0x6F);
583 }
584
585 /* Set CCK and OFDM Block "ON" */
_BBTurnOnBlock(struct adapter * Adapter)586 static void _BBTurnOnBlock(struct adapter *Adapter)
587 {
588 phy_set_bb_reg(Adapter, rFPGA0_RFMOD, bCCKEn, 0x1);
589 phy_set_bb_reg(Adapter, rFPGA0_RFMOD, bOFDMEn, 0x1);
590 }
591
_InitAntenna_Selection(struct adapter * Adapter)592 static void _InitAntenna_Selection(struct adapter *Adapter)
593 {
594 struct hal_data_8188e *haldata = Adapter->HalData;
595
596 if (haldata->AntDivCfg == 0)
597 return;
598 DBG_88E("==> %s ....\n", __func__);
599
600 usb_write32(Adapter, REG_LEDCFG0, usb_read32(Adapter, REG_LEDCFG0) | BIT(23));
601 phy_set_bb_reg(Adapter, rFPGA0_XAB_RFParameter, BIT(13), 0x01);
602
603 if (phy_query_bb_reg(Adapter, rFPGA0_XA_RFInterfaceOE, 0x300) == Antenna_A)
604 haldata->CurAntenna = Antenna_A;
605 else
606 haldata->CurAntenna = Antenna_B;
607 DBG_88E("%s,Cur_ant:(%x)%s\n", __func__, haldata->CurAntenna, (haldata->CurAntenna == Antenna_A) ? "Antenna_A" : "Antenna_B");
608 }
609
610 /*-----------------------------------------------------------------------------
611 * Function: HwSuspendModeEnable92Cu()
612 *
613 * Overview: HW suspend mode switch.
614 *
615 * Input: NONE
616 *
617 * Output: NONE
618 *
619 * Return: NONE
620 *
621 * Revised History:
622 * When Who Remark
623 * 08/23/2010 MHC HW suspend mode switch test..
624 *---------------------------------------------------------------------------
625 */
RfOnOffDetect(struct adapter * adapt)626 enum rt_rf_power_state RfOnOffDetect(struct adapter *adapt)
627 {
628 u8 val8;
629 enum rt_rf_power_state rfpowerstate = rf_off;
630
631 if (adapt->pwrctrlpriv.bHWPowerdown) {
632 val8 = usb_read8(adapt, REG_HSISR);
633 DBG_88E("pwrdown, 0x5c(BIT(7))=%02x\n", val8);
634 rfpowerstate = (val8 & BIT(7)) ? rf_off : rf_on;
635 } else { /* rf on/off */
636 usb_write8(adapt, REG_MAC_PINMUX_CFG, usb_read8(adapt, REG_MAC_PINMUX_CFG) & ~(BIT(3)));
637 val8 = usb_read8(adapt, REG_GPIO_IO_SEL);
638 DBG_88E("GPIO_IN=%02x\n", val8);
639 rfpowerstate = (val8 & BIT(3)) ? rf_on : rf_off;
640 }
641 return rfpowerstate;
642 } /* HalDetectPwrDownMode */
643
rtl8188eu_hal_init(struct adapter * Adapter)644 u32 rtl8188eu_hal_init(struct adapter *Adapter)
645 {
646 u8 value8 = 0;
647 u16 value16;
648 u8 txpktbuf_bndy;
649 u32 status = _SUCCESS;
650 struct hal_data_8188e *haldata = Adapter->HalData;
651 struct pwrctrl_priv *pwrctrlpriv = &Adapter->pwrctrlpriv;
652 struct registry_priv *pregistrypriv = &Adapter->registrypriv;
653 unsigned long init_start_time = jiffies;
654
655 #define HAL_INIT_PROFILE_TAG(stage) do {} while (0)
656
657 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_BEGIN);
658
659 if (Adapter->pwrctrlpriv.bkeepfwalive) {
660 if (haldata->odmpriv.RFCalibrateInfo.bIQKInitialized) {
661 rtl88eu_phy_iq_calibrate(Adapter, true);
662 } else {
663 rtl88eu_phy_iq_calibrate(Adapter, false);
664 haldata->odmpriv.RFCalibrateInfo.bIQKInitialized = true;
665 }
666
667 ODM_TXPowerTrackingCheck(&haldata->odmpriv);
668 rtl88eu_phy_lc_calibrate(Adapter);
669
670 goto exit;
671 }
672
673 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_PW_ON);
674 status = rtw_hal_power_on(Adapter);
675 if (status == _FAIL) {
676 RT_TRACE(_module_hci_hal_init_c_, _drv_err_, ("Failed to init power on!\n"));
677 goto exit;
678 }
679
680 /* Save target channel */
681 haldata->CurrentChannel = 6;/* default set to 6 */
682
683 if (pwrctrlpriv->reg_rfoff)
684 pwrctrlpriv->rf_pwrstate = rf_off;
685
686 /* 2010/08/09 MH We need to check if we need to turnon or off RF after detecting */
687 /* HW GPIO pin. Before PHY_RFConfig8192C. */
688 /* 2010/08/26 MH If Efuse does not support sective suspend then disable the function. */
689
690 if (!pregistrypriv->wifi_spec) {
691 txpktbuf_bndy = TX_PAGE_BOUNDARY_88E;
692 } else {
693 /* for WMM */
694 txpktbuf_bndy = WMM_NORMAL_TX_PAGE_BOUNDARY_88E;
695 }
696
697 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MISC01);
698 _InitQueueReservedPage(Adapter);
699 _InitQueuePriority(Adapter);
700 _InitPageBoundary(Adapter);
701 _InitTransferPageSize(Adapter);
702
703 _InitTxBufferBoundary(Adapter, 0);
704
705 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_DOWNLOAD_FW);
706 if (Adapter->registrypriv.mp_mode == 1) {
707 _InitRxSetting(Adapter);
708 Adapter->bFWReady = false;
709 } else {
710 status = rtl88eu_download_fw(Adapter);
711
712 if (status) {
713 DBG_88E("%s: Download Firmware failed!!\n", __func__);
714 Adapter->bFWReady = false;
715 return status;
716 }
717 RT_TRACE(_module_hci_hal_init_c_, _drv_info_, ("Initializeadapt8192CSdio(): Download Firmware Success!!\n"));
718 Adapter->bFWReady = true;
719 }
720 rtl8188e_InitializeFirmwareVars(Adapter);
721
722 rtl88eu_phy_mac_config(Adapter);
723
724 rtl88eu_phy_bb_config(Adapter);
725
726 rtl88eu_phy_rf_config(Adapter);
727
728 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_EFUSE_PATCH);
729 status = rtl8188e_iol_efuse_patch(Adapter);
730 if (status == _FAIL) {
731 DBG_88E("%s rtl8188e_iol_efuse_patch failed\n", __func__);
732 goto exit;
733 }
734
735 _InitTxBufferBoundary(Adapter, txpktbuf_bndy);
736
737 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_LLTT);
738 status = InitLLTTable(Adapter, txpktbuf_bndy);
739 if (status == _FAIL) {
740 RT_TRACE(_module_hci_hal_init_c_, _drv_err_, ("Failed to init LLT table\n"));
741 goto exit;
742 }
743
744 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MISC02);
745 /* Get Rx PHY status in order to report RSSI and others. */
746 _InitDriverInfoSize(Adapter, DRVINFO_SZ);
747
748 _InitInterrupt(Adapter);
749 rtw_hal_set_hwreg(Adapter, HW_VAR_MAC_ADDR,
750 Adapter->eeprompriv.mac_addr);
751 _InitNetworkType(Adapter);/* set msr */
752 _InitWMACSetting(Adapter);
753 _InitAdaptiveCtrl(Adapter);
754 _InitEDCA(Adapter);
755 _InitRetryFunction(Adapter);
756 InitUsbAggregationSetting(Adapter);
757 _InitBeaconParameters(Adapter);
758 /* Init CR MACTXEN, MACRXEN after setting RxFF boundary REG_TRXFF_BNDY to patch */
759 /* Hw bug which Hw initials RxFF boundary size to a value which is larger than the real Rx buffer size in 88E. */
760 /* Enable MACTXEN/MACRXEN block */
761 value16 = usb_read16(Adapter, REG_CR);
762 value16 |= (MACTXEN | MACRXEN);
763 usb_write8(Adapter, REG_CR, value16);
764
765 if (haldata->bRDGEnable)
766 _InitRDGSetting(Adapter);
767
768 /* Enable TX Report */
769 /* Enable Tx Report Timer */
770 value8 = usb_read8(Adapter, REG_TX_RPT_CTRL);
771 usb_write8(Adapter, REG_TX_RPT_CTRL, (value8 | BIT(1) | BIT(0)));
772 /* Set MAX RPT MACID */
773 usb_write8(Adapter, REG_TX_RPT_CTRL + 1, 2);/* FOR sta mode ,0: bc/mc ,1:AP */
774 /* Tx RPT Timer. Unit: 32us */
775 usb_write16(Adapter, REG_TX_RPT_TIME, 0xCdf0);
776
777 usb_write8(Adapter, REG_EARLY_MODE_CONTROL, 0);
778
779 usb_write16(Adapter, REG_PKT_VO_VI_LIFE_TIME, 0x0400); /* unit: 256us. 256ms */
780 usb_write16(Adapter, REG_PKT_BE_BK_LIFE_TIME, 0x0400); /* unit: 256us. 256ms */
781
782 /* Keep RfRegChnlVal for later use. */
783 haldata->RfRegChnlVal[0] = rtw_hal_read_rfreg(Adapter, (enum rf_radio_path)0, RF_CHNLBW, bRFRegOffsetMask);
784 haldata->RfRegChnlVal[1] = rtw_hal_read_rfreg(Adapter, (enum rf_radio_path)1, RF_CHNLBW, bRFRegOffsetMask);
785
786 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_TURN_ON_BLOCK);
787 _BBTurnOnBlock(Adapter);
788
789 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_SECURITY);
790 invalidate_cam_all(Adapter);
791
792 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_MISC11);
793 /* 2010/12/17 MH We need to set TX power according to EFUSE content at first. */
794 phy_set_tx_power_level(Adapter, haldata->CurrentChannel);
795
796 /* Move by Neo for USB SS to below setp */
797 /* _RfPowerSave(Adapter); */
798
799 _InitAntenna_Selection(Adapter);
800
801 /* */
802 /* Disable BAR, suggested by Scott */
803 /* 2010.04.09 add by hpfan */
804 /* */
805 usb_write32(Adapter, REG_BAR_MODE_CTRL, 0x0201ffff);
806
807 /* HW SEQ CTRL */
808 /* set 0x0 to 0xFF by tynli. Default enable HW SEQ NUM. */
809 usb_write8(Adapter, REG_HWSEQ_CTRL, 0xFF);
810
811 if (pregistrypriv->wifi_spec)
812 usb_write16(Adapter, REG_FAST_EDCA_CTRL, 0);
813
814 /* Nav limit , suggest by scott */
815 usb_write8(Adapter, 0x652, 0x0);
816
817 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_HAL_DM);
818 rtl8188e_InitHalDm(Adapter);
819
820 /* 2010/08/11 MH Merge from 8192SE for Minicard init. We need to confirm current radio status */
821 /* and then decide to enable RF or not.!!!??? For Selective suspend mode. We may not */
822 /* call initstruct adapter. May cause some problem?? */
823 /* Fix the bug that Hw/Sw radio off before S3/S4, the RF off action will not be executed */
824 /* in MgntActSet_RF_State() after wake up, because the value of haldata->eRFPowerState */
825 /* is the same as eRfOff, we should change it to eRfOn after we config RF parameters. */
826 /* Added by tynli. 2010.03.30. */
827 pwrctrlpriv->rf_pwrstate = rf_on;
828
829 /* enable Tx report. */
830 usb_write8(Adapter, REG_FWHW_TXQ_CTRL + 1, 0x0F);
831
832 /* Suggested by SD1 pisa. Added by tynli. 2011.10.21. */
833 usb_write8(Adapter, REG_EARLY_MODE_CONTROL + 3, 0x01);/* Pretx_en, for WEP/TKIP SEC */
834
835 /* tynli_test_tx_report. */
836 usb_write16(Adapter, REG_TX_RPT_TIME, 0x3DF0);
837
838 /* enable tx DMA to drop the redundate data of packet */
839 usb_write16(Adapter, REG_TXDMA_OFFSET_CHK, (usb_read16(Adapter, REG_TXDMA_OFFSET_CHK) | DROP_DATA_EN));
840
841 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_IQK);
842 /* 2010/08/26 MH Merge from 8192CE. */
843 if (pwrctrlpriv->rf_pwrstate == rf_on) {
844 if (haldata->odmpriv.RFCalibrateInfo.bIQKInitialized) {
845 rtl88eu_phy_iq_calibrate(Adapter, true);
846 } else {
847 rtl88eu_phy_iq_calibrate(Adapter, false);
848 haldata->odmpriv.RFCalibrateInfo.bIQKInitialized = true;
849 }
850
851 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_PW_TRACK);
852
853 ODM_TXPowerTrackingCheck(&haldata->odmpriv);
854
855 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_LCK);
856 rtl88eu_phy_lc_calibrate(Adapter);
857 }
858
859 /* HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_INIT_PABIAS); */
860 /* _InitPABias(Adapter); */
861 usb_write8(Adapter, REG_USB_HRPWM, 0);
862
863 /* ack for xmit mgmt frames. */
864 usb_write32(Adapter, REG_FWHW_TXQ_CTRL, usb_read32(Adapter, REG_FWHW_TXQ_CTRL) | BIT(12));
865
866 exit:
867 HAL_INIT_PROFILE_TAG(HAL_INIT_STAGES_END);
868
869 DBG_88E("%s in %dms\n", __func__,
870 jiffies_to_msecs(jiffies - init_start_time));
871
872 return status;
873 }
874
CardDisableRTL8188EU(struct adapter * Adapter)875 static void CardDisableRTL8188EU(struct adapter *Adapter)
876 {
877 u8 val8;
878
879 RT_TRACE(_module_hci_hal_init_c_, _drv_info_, ("CardDisableRTL8188EU\n"));
880
881 /* Stop Tx Report Timer. 0x4EC[Bit1]=b'0 */
882 val8 = usb_read8(Adapter, REG_TX_RPT_CTRL);
883 usb_write8(Adapter, REG_TX_RPT_CTRL, val8 & (~BIT(1)));
884
885 /* stop rx */
886 usb_write8(Adapter, REG_CR, 0x0);
887
888 /* Run LPS WL RFOFF flow */
889 rtl88eu_pwrseqcmdparsing(Adapter, PWR_CUT_ALL_MSK,
890 Rtl8188E_NIC_LPS_ENTER_FLOW);
891
892 /* 2. 0x1F[7:0] = 0 turn off RF */
893
894 val8 = usb_read8(Adapter, REG_MCUFWDL);
895 if ((val8 & RAM_DL_SEL) && Adapter->bFWReady) { /* 8051 RAM code */
896 /* Reset MCU 0x2[10]=0. */
897 val8 = usb_read8(Adapter, REG_SYS_FUNC_EN + 1);
898 val8 &= ~BIT(2); /* 0x2[10], FEN_CPUEN */
899 usb_write8(Adapter, REG_SYS_FUNC_EN + 1, val8);
900 }
901
902 /* reset MCU ready status */
903 usb_write8(Adapter, REG_MCUFWDL, 0);
904
905 /* YJ,add,111212 */
906 /* Disable 32k */
907 val8 = usb_read8(Adapter, REG_32K_CTRL);
908 usb_write8(Adapter, REG_32K_CTRL, val8 & (~BIT(0)));
909
910 /* Card disable power action flow */
911 rtl88eu_pwrseqcmdparsing(Adapter, PWR_CUT_ALL_MSK,
912 Rtl8188E_NIC_DISABLE_FLOW);
913
914 /* Reset MCU IO Wrapper */
915 val8 = usb_read8(Adapter, REG_RSV_CTRL + 1);
916 usb_write8(Adapter, REG_RSV_CTRL + 1, (val8 & (~BIT(3))));
917 val8 = usb_read8(Adapter, REG_RSV_CTRL + 1);
918 usb_write8(Adapter, REG_RSV_CTRL + 1, val8 | BIT(3));
919
920 /* YJ,test add, 111207. For Power Consumption. */
921 val8 = usb_read8(Adapter, GPIO_IN);
922 usb_write8(Adapter, GPIO_OUT, val8);
923 usb_write8(Adapter, GPIO_IO_SEL, 0xFF);/* Reg0x46 */
924
925 val8 = usb_read8(Adapter, REG_GPIO_IO_SEL);
926 usb_write8(Adapter, REG_GPIO_IO_SEL, (val8 << 4));
927 val8 = usb_read8(Adapter, REG_GPIO_IO_SEL + 1);
928 usb_write8(Adapter, REG_GPIO_IO_SEL + 1, val8 | 0x0F);/* Reg0x43 */
929 usb_write32(Adapter, REG_BB_PAD_CTRL, 0x00080808);/* set LNA ,TRSW,EX_PA Pin to output mode */
930 Adapter->HalData->bMacPwrCtrlOn = false;
931 Adapter->bFWReady = false;
932 }
933
rtl8192cu_hw_power_down(struct adapter * adapt)934 static void rtl8192cu_hw_power_down(struct adapter *adapt)
935 {
936 /* 2010/-8/09 MH For power down module, we need to enable register block contrl reg at 0x1c. */
937 /* Then enable power down control bit of register 0x04 BIT4 and BIT15 as 1. */
938
939 /* Enable register area 0x0-0xc. */
940 usb_write8(adapt, REG_RSV_CTRL, 0x0);
941 usb_write16(adapt, REG_APS_FSMCO, 0x8812);
942 }
943
rtl8188eu_hal_deinit(struct adapter * Adapter)944 u32 rtl8188eu_hal_deinit(struct adapter *Adapter)
945 {
946 DBG_88E("==> %s\n", __func__);
947
948 usb_write32(Adapter, REG_HIMR_88E, IMR_DISABLED_88E);
949 usb_write32(Adapter, REG_HIMRE_88E, IMR_DISABLED_88E);
950
951 DBG_88E("bkeepfwalive(%x)\n", Adapter->pwrctrlpriv.bkeepfwalive);
952 if (Adapter->pwrctrlpriv.bkeepfwalive) {
953 if ((Adapter->pwrctrlpriv.bHWPwrPindetect) && (Adapter->pwrctrlpriv.bHWPowerdown))
954 rtl8192cu_hw_power_down(Adapter);
955 } else {
956 if (Adapter->hw_init_completed) {
957 CardDisableRTL8188EU(Adapter);
958
959 if ((Adapter->pwrctrlpriv.bHWPwrPindetect) && (Adapter->pwrctrlpriv.bHWPowerdown))
960 rtl8192cu_hw_power_down(Adapter);
961 }
962 }
963 return _SUCCESS;
964 }
965
rtw_hal_inirp_init(struct adapter * Adapter)966 u32 rtw_hal_inirp_init(struct adapter *Adapter)
967 {
968 u8 i;
969 struct recv_buf *precvbuf;
970 uint status;
971 struct recv_priv *precvpriv = &Adapter->recvpriv;
972
973 status = _SUCCESS;
974
975 RT_TRACE(_module_hci_hal_init_c_, _drv_info_,
976 ("===> usb_inirp_init\n"));
977
978 /* issue Rx irp to receive data */
979 precvbuf = precvpriv->precv_buf;
980 for (i = 0; i < NR_RECVBUFF; i++) {
981 if (!usb_read_port(Adapter, RECV_BULK_IN_ADDR, precvbuf)) {
982 RT_TRACE(_module_hci_hal_init_c_, _drv_err_, ("usb_rx_init: usb_read_port error\n"));
983 status = _FAIL;
984 goto exit;
985 }
986
987 precvbuf++;
988 }
989
990 exit:
991
992 RT_TRACE(_module_hci_hal_init_c_, _drv_info_, ("<=== usb_inirp_init\n"));
993
994 return status;
995 }
996
997 /* */
998 /* */
999 /* EEPROM/EFUSE Content Parsing */
1000 /* */
1001 /* */
Hal_EfuseParsePIDVID_8188EU(struct adapter * adapt,u8 * hwinfo,bool AutoLoadFail)1002 static void Hal_EfuseParsePIDVID_8188EU(struct adapter *adapt, u8 *hwinfo, bool AutoLoadFail)
1003 {
1004 struct hal_data_8188e *haldata = adapt->HalData;
1005
1006 if (!AutoLoadFail) {
1007 /* VID, PID */
1008 haldata->EEPROMVID = EF2BYTE(*(__le16 *)&hwinfo[EEPROM_VID_88EU]);
1009 haldata->EEPROMPID = EF2BYTE(*(__le16 *)&hwinfo[EEPROM_PID_88EU]);
1010
1011 /* Customer ID, 0x00 and 0xff are reserved for Realtek. */
1012 haldata->EEPROMCustomerID = *(u8 *)&hwinfo[EEPROM_CUSTOMERID_88E];
1013 haldata->EEPROMSubCustomerID = EEPROM_Default_SubCustomerID;
1014 } else {
1015 haldata->EEPROMVID = EEPROM_Default_VID;
1016 haldata->EEPROMPID = EEPROM_Default_PID;
1017
1018 /* Customer ID, 0x00 and 0xff are reserved for Realtek. */
1019 haldata->EEPROMCustomerID = EEPROM_Default_CustomerID;
1020 haldata->EEPROMSubCustomerID = EEPROM_Default_SubCustomerID;
1021 }
1022
1023 DBG_88E("VID = 0x%04X, PID = 0x%04X\n", haldata->EEPROMVID, haldata->EEPROMPID);
1024 DBG_88E("Customer ID: 0x%02X, SubCustomer ID: 0x%02X\n", haldata->EEPROMCustomerID, haldata->EEPROMSubCustomerID);
1025 }
1026
Hal_EfuseParseMACAddr_8188EU(struct adapter * adapt,u8 * hwinfo,bool AutoLoadFail)1027 static void Hal_EfuseParseMACAddr_8188EU(struct adapter *adapt, u8 *hwinfo, bool AutoLoadFail)
1028 {
1029 u16 i;
1030 u8 sMacAddr[6] = {0x00, 0xE0, 0x4C, 0x81, 0x88, 0x02};
1031 struct eeprom_priv *eeprom = GET_EEPROM_EFUSE_PRIV(adapt);
1032
1033 if (AutoLoadFail) {
1034 for (i = 0; i < 6; i++)
1035 eeprom->mac_addr[i] = sMacAddr[i];
1036 } else {
1037 /* Read Permanent MAC address */
1038 memcpy(eeprom->mac_addr, &hwinfo[EEPROM_MAC_ADDR_88EU], ETH_ALEN);
1039 }
1040 RT_TRACE(_module_hci_hal_init_c_, _drv_notice_,
1041 ("Hal_EfuseParseMACAddr_8188EU: Permanent Address = %pM\n",
1042 eeprom->mac_addr));
1043 }
1044
readAdapterInfo_8188EU(struct adapter * adapt)1045 static void readAdapterInfo_8188EU(struct adapter *adapt)
1046 {
1047 struct eeprom_priv *eeprom = GET_EEPROM_EFUSE_PRIV(adapt);
1048
1049 /* parse the eeprom/efuse content */
1050 Hal_EfuseParseIDCode88E(adapt, eeprom->efuse_eeprom_data);
1051 Hal_EfuseParsePIDVID_8188EU(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1052 Hal_EfuseParseMACAddr_8188EU(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1053
1054 Hal_ReadPowerSavingMode88E(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1055 Hal_ReadTxPowerInfo88E(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1056 Hal_EfuseParseEEPROMVer88E(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1057 rtl8188e_EfuseParseChnlPlan(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1058 Hal_EfuseParseXtal_8188E(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1059 Hal_EfuseParseCustomerID88E(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1060 Hal_ReadAntennaDiversity88E(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1061 Hal_EfuseParseBoardType88E(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1062 Hal_ReadThermalMeter_88E(adapt, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
1063 }
1064
_ReadPROMContent(struct adapter * Adapter)1065 static void _ReadPROMContent(struct adapter *Adapter)
1066 {
1067 struct eeprom_priv *eeprom = GET_EEPROM_EFUSE_PRIV(Adapter);
1068 u8 eeValue;
1069
1070 /* check system boot selection */
1071 eeValue = usb_read8(Adapter, REG_9346CR);
1072 eeprom->EepromOrEfuse = (eeValue & BOOT_FROM_EEPROM) ? true : false;
1073 eeprom->bautoload_fail_flag = (eeValue & EEPROM_EN) ? false : true;
1074
1075 DBG_88E("Boot from %s, Autoload %s !\n", (eeprom->EepromOrEfuse ? "EEPROM" : "EFUSE"),
1076 (eeprom->bautoload_fail_flag ? "Fail" : "OK"));
1077
1078 Hal_InitPGData88E(Adapter);
1079 readAdapterInfo_8188EU(Adapter);
1080 }
1081
rtw_hal_read_chip_info(struct adapter * Adapter)1082 void rtw_hal_read_chip_info(struct adapter *Adapter)
1083 {
1084 unsigned long start = jiffies;
1085
1086 MSG_88E("====> %s\n", __func__);
1087
1088 _ReadPROMContent(Adapter);
1089
1090 MSG_88E("<==== %s in %d ms\n", __func__,
1091 jiffies_to_msecs(jiffies - start));
1092 }
1093
1094 #define GPIO_DEBUG_PORT_NUM 0
rtl8192cu_trigger_gpio_0(struct adapter * adapt)1095 static void rtl8192cu_trigger_gpio_0(struct adapter *adapt)
1096 {
1097 }
1098
ResumeTxBeacon(struct adapter * adapt)1099 static void ResumeTxBeacon(struct adapter *adapt)
1100 {
1101 struct hal_data_8188e *haldata = adapt->HalData;
1102
1103 /* 2010.03.01. Marked by tynli. No need to call workitem beacause we record the value */
1104 /* which should be read from register to a global variable. */
1105
1106 usb_write8(adapt, REG_FWHW_TXQ_CTRL + 2, (haldata->RegFwHwTxQCtrl) | BIT(6));
1107 haldata->RegFwHwTxQCtrl |= BIT(6);
1108 usb_write8(adapt, REG_TBTT_PROHIBIT + 1, 0xff);
1109 haldata->RegReg542 |= BIT(0);
1110 usb_write8(adapt, REG_TBTT_PROHIBIT + 2, haldata->RegReg542);
1111 }
1112
StopTxBeacon(struct adapter * adapt)1113 static void StopTxBeacon(struct adapter *adapt)
1114 {
1115 struct hal_data_8188e *haldata = adapt->HalData;
1116
1117 /* 2010.03.01. Marked by tynli. No need to call workitem beacause we record the value */
1118 /* which should be read from register to a global variable. */
1119
1120 usb_write8(adapt, REG_FWHW_TXQ_CTRL + 2, (haldata->RegFwHwTxQCtrl) & (~BIT(6)));
1121 haldata->RegFwHwTxQCtrl &= (~BIT(6));
1122 usb_write8(adapt, REG_TBTT_PROHIBIT + 1, 0x64);
1123 haldata->RegReg542 &= ~(BIT(0));
1124 usb_write8(adapt, REG_TBTT_PROHIBIT + 2, haldata->RegReg542);
1125
1126 /* todo: CheckFwRsvdPageContent(Adapter); 2010.06.23. Added by tynli. */
1127 }
1128
hw_var_set_opmode(struct adapter * Adapter,u8 variable,u8 * val)1129 static void hw_var_set_opmode(struct adapter *Adapter, u8 variable, u8 *val)
1130 {
1131 u8 val8;
1132 u8 mode = *((u8 *)val);
1133
1134 /* disable Port0 TSF update */
1135 usb_write8(Adapter, REG_BCN_CTRL, usb_read8(Adapter, REG_BCN_CTRL) | BIT(4));
1136
1137 /* set net_type */
1138 val8 = usb_read8(Adapter, MSR) & 0x0c;
1139 val8 |= mode;
1140 usb_write8(Adapter, MSR, val8);
1141
1142 DBG_88E("%s()-%d mode = %d\n", __func__, __LINE__, mode);
1143
1144 if ((mode == _HW_STATE_STATION_) || (mode == _HW_STATE_NOLINK_)) {
1145 StopTxBeacon(Adapter);
1146
1147 usb_write8(Adapter, REG_BCN_CTRL, 0x19);/* disable atim wnd */
1148 } else if (mode == _HW_STATE_ADHOC_) {
1149 ResumeTxBeacon(Adapter);
1150 usb_write8(Adapter, REG_BCN_CTRL, 0x1a);
1151 } else if (mode == _HW_STATE_AP_) {
1152 ResumeTxBeacon(Adapter);
1153
1154 usb_write8(Adapter, REG_BCN_CTRL, 0x12);
1155
1156 /* Set RCR */
1157 usb_write32(Adapter, REG_RCR, 0x7000208e);/* CBSSID_DATA must set to 0,reject ICV_ERR packet */
1158 /* enable to rx data frame */
1159 usb_write16(Adapter, REG_RXFLTMAP2, 0xFFFF);
1160 /* enable to rx ps-poll */
1161 usb_write16(Adapter, REG_RXFLTMAP1, 0x0400);
1162
1163 /* Beacon Control related register for first time */
1164 usb_write8(Adapter, REG_BCNDMATIM, 0x02); /* 2ms */
1165
1166 usb_write8(Adapter, REG_ATIMWND, 0x0a); /* 10ms */
1167 usb_write16(Adapter, REG_BCNTCFG, 0x00);
1168 usb_write16(Adapter, REG_TBTT_PROHIBIT, 0xff04);
1169 usb_write16(Adapter, REG_TSFTR_SYN_OFFSET, 0x7fff);/* +32767 (~32ms) */
1170
1171 /* reset TSF */
1172 usb_write8(Adapter, REG_DUAL_TSF_RST, BIT(0));
1173
1174 /* BIT3 - If set 0, hw will clr bcnq when tx becon ok/fail or port 0 */
1175 usb_write8(Adapter, REG_MBID_NUM, usb_read8(Adapter, REG_MBID_NUM) | BIT(3) | BIT(4));
1176
1177 /* enable BCN0 Function for if1 */
1178 /* don't enable update TSF0 for if1 (due to TSF update when beacon/probe rsp are received) */
1179 usb_write8(Adapter, REG_BCN_CTRL, (DIS_TSF_UDT0_NORMAL_CHIP | EN_BCN_FUNCTION | BIT(1)));
1180
1181 /* dis BCN1 ATIM WND if if2 is station */
1182 usb_write8(Adapter, REG_BCN_CTRL_1, usb_read8(Adapter, REG_BCN_CTRL_1) | BIT(0));
1183 }
1184 }
1185
hw_var_set_macaddr(struct adapter * Adapter,u8 variable,u8 * val)1186 static void hw_var_set_macaddr(struct adapter *Adapter, u8 variable, u8 *val)
1187 {
1188 u8 idx = 0;
1189 u32 reg_macid;
1190
1191 reg_macid = REG_MACID;
1192
1193 for (idx = 0; idx < 6; idx++)
1194 usb_write8(Adapter, (reg_macid + idx), val[idx]);
1195 }
1196
hw_var_set_bssid(struct adapter * Adapter,u8 variable,u8 * val)1197 static void hw_var_set_bssid(struct adapter *Adapter, u8 variable, u8 *val)
1198 {
1199 u8 idx = 0;
1200 u32 reg_bssid;
1201
1202 reg_bssid = REG_BSSID;
1203
1204 for (idx = 0; idx < 6; idx++)
1205 usb_write8(Adapter, (reg_bssid + idx), val[idx]);
1206 }
1207
hw_var_set_bcn_func(struct adapter * Adapter,u8 variable,u8 * val)1208 static void hw_var_set_bcn_func(struct adapter *Adapter, u8 variable, u8 *val)
1209 {
1210 u32 bcn_ctrl_reg;
1211
1212 bcn_ctrl_reg = REG_BCN_CTRL;
1213
1214 if (*((u8 *)val))
1215 usb_write8(Adapter, bcn_ctrl_reg, (EN_BCN_FUNCTION | EN_TXBCN_RPT));
1216 else
1217 usb_write8(Adapter, bcn_ctrl_reg, usb_read8(Adapter, bcn_ctrl_reg) & (~(EN_BCN_FUNCTION | EN_TXBCN_RPT)));
1218 }
1219
rtw_hal_set_hwreg(struct adapter * Adapter,u8 variable,u8 * val)1220 void rtw_hal_set_hwreg(struct adapter *Adapter, u8 variable, u8 *val)
1221 {
1222 struct hal_data_8188e *haldata = Adapter->HalData;
1223 struct dm_priv *pdmpriv = &haldata->dmpriv;
1224 struct odm_dm_struct *podmpriv = &haldata->odmpriv;
1225
1226 switch (variable) {
1227 case HW_VAR_MEDIA_STATUS:
1228 {
1229 u8 val8;
1230
1231 val8 = usb_read8(Adapter, MSR) & 0x0c;
1232 val8 |= *((u8 *)val);
1233 usb_write8(Adapter, MSR, val8);
1234 }
1235 break;
1236 case HW_VAR_MEDIA_STATUS1:
1237 {
1238 u8 val8;
1239
1240 val8 = usb_read8(Adapter, MSR) & 0x03;
1241 val8 |= *((u8 *)val) << 2;
1242 usb_write8(Adapter, MSR, val8);
1243 }
1244 break;
1245 case HW_VAR_SET_OPMODE:
1246 hw_var_set_opmode(Adapter, variable, val);
1247 break;
1248 case HW_VAR_MAC_ADDR:
1249 hw_var_set_macaddr(Adapter, variable, val);
1250 break;
1251 case HW_VAR_BSSID:
1252 hw_var_set_bssid(Adapter, variable, val);
1253 break;
1254 case HW_VAR_BASIC_RATE:
1255 {
1256 u16 BrateCfg = 0;
1257 u8 RateIndex = 0;
1258
1259 /* 2007.01.16, by Emily */
1260 /* Select RRSR (in Legacy-OFDM and CCK) */
1261 /* For 8190, we select only 24M, 12M, 6M, 11M, 5.5M, 2M, and 1M from the Basic rate. */
1262 /* We do not use other rates. */
1263 hal_set_brate_cfg(val, &BrateCfg);
1264 DBG_88E("HW_VAR_BASIC_RATE: BrateCfg(%#x)\n", BrateCfg);
1265
1266 /* 2011.03.30 add by Luke Lee */
1267 /* CCK 2M ACK should be disabled for some BCM and Atheros AP IOT */
1268 /* because CCK 2M has poor TXEVM */
1269 /* CCK 5.5M & 11M ACK should be enabled for better performance */
1270
1271 BrateCfg = (BrateCfg | 0xd) & 0x15d;
1272 haldata->BasicRateSet = BrateCfg;
1273
1274 BrateCfg |= 0x01; /* default enable 1M ACK rate */
1275 /* Set RRSR rate table. */
1276 usb_write8(Adapter, REG_RRSR, BrateCfg & 0xff);
1277 usb_write8(Adapter, REG_RRSR + 1, (BrateCfg >> 8) & 0xff);
1278 usb_write8(Adapter, REG_RRSR + 2, usb_read8(Adapter, REG_RRSR + 2) & 0xf0);
1279
1280 /* Set RTS initial rate */
1281 while (BrateCfg > 0x1) {
1282 BrateCfg >>= 1;
1283 RateIndex++;
1284 }
1285 /* Ziv - Check */
1286 usb_write8(Adapter, REG_INIRTS_RATE_SEL, RateIndex);
1287 }
1288 break;
1289 case HW_VAR_TXPAUSE:
1290 usb_write8(Adapter, REG_TXPAUSE, *((u8 *)val));
1291 break;
1292 case HW_VAR_BCN_FUNC:
1293 hw_var_set_bcn_func(Adapter, variable, val);
1294 break;
1295 case HW_VAR_CORRECT_TSF:
1296 {
1297 u64 tsf;
1298 struct mlme_ext_priv *pmlmeext = &Adapter->mlmeextpriv;
1299 struct mlme_ext_info *pmlmeinfo = &pmlmeext->mlmext_info;
1300
1301 tsf = pmlmeext->TSFValue - do_div(pmlmeext->TSFValue, (pmlmeinfo->bcn_interval * 1024)) - 1024; /* us */
1302
1303 if (((pmlmeinfo->state & 0x03) == WIFI_FW_ADHOC_STATE) || ((pmlmeinfo->state & 0x03) == WIFI_FW_AP_STATE))
1304 StopTxBeacon(Adapter);
1305
1306 /* disable related TSF function */
1307 usb_write8(Adapter, REG_BCN_CTRL, usb_read8(Adapter, REG_BCN_CTRL) & (~BIT(3)));
1308
1309 usb_write32(Adapter, REG_TSFTR, tsf);
1310 usb_write32(Adapter, REG_TSFTR + 4, tsf >> 32);
1311
1312 /* enable related TSF function */
1313 usb_write8(Adapter, REG_BCN_CTRL, usb_read8(Adapter, REG_BCN_CTRL) | BIT(3));
1314
1315 if (((pmlmeinfo->state & 0x03) == WIFI_FW_ADHOC_STATE) || ((pmlmeinfo->state & 0x03) == WIFI_FW_AP_STATE))
1316 ResumeTxBeacon(Adapter);
1317 }
1318 break;
1319 case HW_VAR_CHECK_BSSID:
1320 if (*((u8 *)val)) {
1321 usb_write32(Adapter, REG_RCR, usb_read32(Adapter, REG_RCR) | RCR_CBSSID_DATA | RCR_CBSSID_BCN);
1322 } else {
1323 u32 val32;
1324
1325 val32 = usb_read32(Adapter, REG_RCR);
1326
1327 val32 &= ~(RCR_CBSSID_DATA | RCR_CBSSID_BCN);
1328
1329 usb_write32(Adapter, REG_RCR, val32);
1330 }
1331 break;
1332 case HW_VAR_MLME_DISCONNECT:
1333 /* Set RCR to not to receive data frame when NO LINK state */
1334 /* reject all data frames */
1335 usb_write16(Adapter, REG_RXFLTMAP2, 0x00);
1336
1337 /* reset TSF */
1338 usb_write8(Adapter, REG_DUAL_TSF_RST, (BIT(0) | BIT(1)));
1339
1340 /* disable update TSF */
1341 usb_write8(Adapter, REG_BCN_CTRL, usb_read8(Adapter, REG_BCN_CTRL) | BIT(4));
1342 break;
1343 case HW_VAR_MLME_SITESURVEY:
1344 if (*((u8 *)val)) { /* under sitesurvey */
1345 /* config RCR to receive different BSSID & not to receive data frame */
1346 u32 v = usb_read32(Adapter, REG_RCR);
1347
1348 v &= ~(RCR_CBSSID_BCN);
1349 usb_write32(Adapter, REG_RCR, v);
1350 /* reject all data frame */
1351 usb_write16(Adapter, REG_RXFLTMAP2, 0x00);
1352
1353 /* disable update TSF */
1354 usb_write8(Adapter, REG_BCN_CTRL, usb_read8(Adapter, REG_BCN_CTRL) | BIT(4));
1355 } else { /* sitesurvey done */
1356 struct mlme_ext_priv *pmlmeext = &Adapter->mlmeextpriv;
1357 struct mlme_ext_info *pmlmeinfo = &pmlmeext->mlmext_info;
1358
1359 if ((is_client_associated_to_ap(Adapter)) ||
1360 ((pmlmeinfo->state & 0x03) == WIFI_FW_ADHOC_STATE)) {
1361 /* enable to rx data frame */
1362 usb_write16(Adapter, REG_RXFLTMAP2, 0xFFFF);
1363
1364 /* enable update TSF */
1365 usb_write8(Adapter, REG_BCN_CTRL, usb_read8(Adapter, REG_BCN_CTRL) & (~BIT(4)));
1366 } else if ((pmlmeinfo->state & 0x03) == WIFI_FW_AP_STATE) {
1367 usb_write16(Adapter, REG_RXFLTMAP2, 0xFFFF);
1368 /* enable update TSF */
1369 usb_write8(Adapter, REG_BCN_CTRL, usb_read8(Adapter, REG_BCN_CTRL) & (~BIT(4)));
1370 }
1371
1372 usb_write32(Adapter, REG_RCR, usb_read32(Adapter, REG_RCR) | RCR_CBSSID_BCN);
1373 }
1374 break;
1375 case HW_VAR_MLME_JOIN:
1376 {
1377 u8 RetryLimit = 0x30;
1378 u8 type = *((u8 *)val);
1379 struct mlme_priv *pmlmepriv = &Adapter->mlmepriv;
1380
1381 if (type == 0) { /* prepare to join */
1382 /* enable to rx data frame.Accept all data frame */
1383 usb_write16(Adapter, REG_RXFLTMAP2, 0xFFFF);
1384
1385 usb_write32(Adapter, REG_RCR, usb_read32(Adapter, REG_RCR) | RCR_CBSSID_DATA | RCR_CBSSID_BCN);
1386
1387 if (check_fwstate(pmlmepriv, WIFI_STATION_STATE))
1388 RetryLimit = (haldata->CustomerID == RT_CID_CCX) ? 7 : 48;
1389 else /* Ad-hoc Mode */
1390 RetryLimit = 0x7;
1391 } else if (type == 1) {
1392 /* joinbss_event call back when join res < 0 */
1393 usb_write16(Adapter, REG_RXFLTMAP2, 0x00);
1394 } else if (type == 2) {
1395 /* sta add event call back */
1396 /* enable update TSF */
1397 usb_write8(Adapter, REG_BCN_CTRL, usb_read8(Adapter, REG_BCN_CTRL) & (~BIT(4)));
1398
1399 if (check_fwstate(pmlmepriv, WIFI_ADHOC_STATE | WIFI_ADHOC_MASTER_STATE))
1400 RetryLimit = 0x7;
1401 }
1402 usb_write16(Adapter, REG_RL, RetryLimit << RETRY_LIMIT_SHORT_SHIFT | RetryLimit << RETRY_LIMIT_LONG_SHIFT);
1403 }
1404 break;
1405 case HW_VAR_BEACON_INTERVAL:
1406 usb_write16(Adapter, REG_BCN_INTERVAL, *((u16 *)val));
1407 break;
1408 case HW_VAR_SLOT_TIME:
1409 {
1410 u8 u1bAIFS, aSifsTime;
1411 struct mlme_ext_priv *pmlmeext = &Adapter->mlmeextpriv;
1412 struct mlme_ext_info *pmlmeinfo = &pmlmeext->mlmext_info;
1413
1414 usb_write8(Adapter, REG_SLOT, val[0]);
1415
1416 if (pmlmeinfo->WMM_enable == 0) {
1417 if (pmlmeext->cur_wireless_mode == WIRELESS_11B)
1418 aSifsTime = 10;
1419 else
1420 aSifsTime = 16;
1421
1422 u1bAIFS = aSifsTime + (2 * pmlmeinfo->slotTime);
1423
1424 /* <Roger_EXP> Temporary removed, 2008.06.20. */
1425 usb_write8(Adapter, REG_EDCA_VO_PARAM, u1bAIFS);
1426 usb_write8(Adapter, REG_EDCA_VI_PARAM, u1bAIFS);
1427 usb_write8(Adapter, REG_EDCA_BE_PARAM, u1bAIFS);
1428 usb_write8(Adapter, REG_EDCA_BK_PARAM, u1bAIFS);
1429 }
1430 }
1431 break;
1432 case HW_VAR_RESP_SIFS:
1433 /* RESP_SIFS for CCK */
1434 usb_write8(Adapter, REG_R2T_SIFS, val[0]); /* SIFS_T2T_CCK (0x08) */
1435 usb_write8(Adapter, REG_R2T_SIFS + 1, val[1]); /* SIFS_R2T_CCK(0x08) */
1436 /* RESP_SIFS for OFDM */
1437 usb_write8(Adapter, REG_T2T_SIFS, val[2]); /* SIFS_T2T_OFDM (0x0a) */
1438 usb_write8(Adapter, REG_T2T_SIFS + 1, val[3]); /* SIFS_R2T_OFDM(0x0a) */
1439 break;
1440 case HW_VAR_ACK_PREAMBLE:
1441 {
1442 u8 regTmp;
1443 u8 bShortPreamble = *((bool *)val);
1444 /* Joseph marked out for Netgear 3500 TKIP channel 7 issue.(Temporarily) */
1445 regTmp = (haldata->nCur40MhzPrimeSC) << 5;
1446 if (bShortPreamble)
1447 regTmp |= 0x80;
1448
1449 usb_write8(Adapter, REG_RRSR + 2, regTmp);
1450 }
1451 break;
1452 case HW_VAR_SEC_CFG:
1453 usb_write8(Adapter, REG_SECCFG, *((u8 *)val));
1454 break;
1455 case HW_VAR_DM_FUNC_OP:
1456 if (val[0])
1457 podmpriv->BK_SupportAbility = podmpriv->SupportAbility;
1458 else
1459 podmpriv->SupportAbility = podmpriv->BK_SupportAbility;
1460 break;
1461 case HW_VAR_DM_FUNC_SET:
1462 if (*((u32 *)val) == DYNAMIC_ALL_FUNC_ENABLE) {
1463 pdmpriv->DMFlag = pdmpriv->InitDMFlag;
1464 podmpriv->SupportAbility = pdmpriv->InitODMFlag;
1465 } else {
1466 podmpriv->SupportAbility |= *((u32 *)val);
1467 }
1468 break;
1469 case HW_VAR_DM_FUNC_CLR:
1470 podmpriv->SupportAbility &= *((u32 *)val);
1471 break;
1472 case HW_VAR_CAM_EMPTY_ENTRY:
1473 {
1474 u8 ucIndex = *((u8 *)val);
1475 u8 i;
1476 u32 ulCommand = 0;
1477 u32 ulContent = 0;
1478 u32 ulEncAlgo = CAM_AES;
1479
1480 for (i = 0; i < CAM_CONTENT_COUNT; i++) {
1481 /* filled id in CAM config 2 byte */
1482 if (i == 0)
1483 ulContent |= (ucIndex & 0x03) | ((u16)(ulEncAlgo) << 2);
1484 else
1485 ulContent = 0;
1486 /* polling bit, and No Write enable, and address */
1487 ulCommand = CAM_CONTENT_COUNT * ucIndex + i;
1488 ulCommand = ulCommand | CAM_POLLINIG |
1489 CAM_WRITE;
1490 /* write content 0 is equall to mark invalid */
1491 usb_write32(Adapter, WCAMI, ulContent); /* delay_ms(40); */
1492 usb_write32(Adapter, RWCAM, ulCommand); /* delay_ms(40); */
1493 }
1494 }
1495 break;
1496 case HW_VAR_CAM_INVALID_ALL:
1497 usb_write32(Adapter, RWCAM, BIT(31) | BIT(30));
1498 break;
1499 case HW_VAR_CAM_WRITE:
1500 {
1501 u32 cmd;
1502 u32 *cam_val = (u32 *)val;
1503
1504 usb_write32(Adapter, WCAMI, cam_val[0]);
1505
1506 cmd = CAM_POLLINIG | CAM_WRITE | cam_val[1];
1507 usb_write32(Adapter, RWCAM, cmd);
1508 }
1509 break;
1510 case HW_VAR_AC_PARAM_VO:
1511 usb_write32(Adapter, REG_EDCA_VO_PARAM, ((u32 *)(val))[0]);
1512 break;
1513 case HW_VAR_AC_PARAM_VI:
1514 usb_write32(Adapter, REG_EDCA_VI_PARAM, ((u32 *)(val))[0]);
1515 break;
1516 case HW_VAR_AC_PARAM_BE:
1517 haldata->AcParam_BE = ((u32 *)(val))[0];
1518 usb_write32(Adapter, REG_EDCA_BE_PARAM, ((u32 *)(val))[0]);
1519 break;
1520 case HW_VAR_AC_PARAM_BK:
1521 usb_write32(Adapter, REG_EDCA_BK_PARAM, ((u32 *)(val))[0]);
1522 break;
1523 case HW_VAR_ACM_CTRL:
1524 {
1525 u8 acm_ctrl = *((u8 *)val);
1526 u8 AcmCtrl = usb_read8(Adapter, REG_ACMHWCTRL);
1527
1528 if (acm_ctrl > 1)
1529 AcmCtrl = AcmCtrl | 0x1;
1530
1531 if (acm_ctrl & BIT(3))
1532 AcmCtrl |= AcmHw_VoqEn;
1533 else
1534 AcmCtrl &= (~AcmHw_VoqEn);
1535
1536 if (acm_ctrl & BIT(2))
1537 AcmCtrl |= AcmHw_ViqEn;
1538 else
1539 AcmCtrl &= (~AcmHw_ViqEn);
1540
1541 if (acm_ctrl & BIT(1))
1542 AcmCtrl |= AcmHw_BeqEn;
1543 else
1544 AcmCtrl &= (~AcmHw_BeqEn);
1545
1546 DBG_88E("[HW_VAR_ACM_CTRL] Write 0x%X\n", AcmCtrl);
1547 usb_write8(Adapter, REG_ACMHWCTRL, AcmCtrl);
1548 }
1549 break;
1550 case HW_VAR_AMPDU_MIN_SPACE:
1551 {
1552 u8 MinSpacingToSet;
1553 u8 SecMinSpace;
1554
1555 MinSpacingToSet = *((u8 *)val);
1556 if (MinSpacingToSet <= 7) {
1557 switch (Adapter->securitypriv.dot11PrivacyAlgrthm) {
1558 case _NO_PRIVACY_:
1559 case _AES_:
1560 SecMinSpace = 0;
1561 break;
1562 case _WEP40_:
1563 case _WEP104_:
1564 case _TKIP_:
1565 case _TKIP_WTMIC_:
1566 SecMinSpace = 6;
1567 break;
1568 default:
1569 SecMinSpace = 7;
1570 break;
1571 }
1572 if (MinSpacingToSet < SecMinSpace)
1573 MinSpacingToSet = SecMinSpace;
1574 usb_write8(Adapter, REG_AMPDU_MIN_SPACE, (usb_read8(Adapter, REG_AMPDU_MIN_SPACE) & 0xf8) | MinSpacingToSet);
1575 }
1576 }
1577 break;
1578 case HW_VAR_AMPDU_FACTOR:
1579 {
1580 u8 RegToSet_Normal[4] = {0x41, 0xa8, 0x72, 0xb9};
1581 u8 FactorToSet;
1582 u8 *pRegToSet;
1583 u8 index = 0;
1584
1585 pRegToSet = RegToSet_Normal; /* 0xb972a841; */
1586 FactorToSet = *((u8 *)val);
1587 if (FactorToSet <= 3) {
1588 FactorToSet = 1 << (FactorToSet + 2);
1589 if (FactorToSet > 0xf)
1590 FactorToSet = 0xf;
1591
1592 for (index = 0; index < 4; index++) {
1593 if ((pRegToSet[index] & 0xf0) > (FactorToSet << 4))
1594 pRegToSet[index] = (pRegToSet[index] & 0x0f) | (FactorToSet << 4);
1595
1596 if ((pRegToSet[index] & 0x0f) > FactorToSet)
1597 pRegToSet[index] = (pRegToSet[index] & 0xf0) | (FactorToSet);
1598
1599 usb_write8(Adapter, (REG_AGGLEN_LMT + index), pRegToSet[index]);
1600 }
1601 }
1602 }
1603 break;
1604 case HW_VAR_RXDMA_AGG_PG_TH:
1605 {
1606 u8 threshold = *((u8 *)val);
1607
1608 if (threshold == 0)
1609 threshold = haldata->UsbRxAggPageCount;
1610 usb_write8(Adapter, REG_RXDMA_AGG_PG_TH, threshold);
1611 }
1612 break;
1613 case HW_VAR_SET_RPWM:
1614 break;
1615 case HW_VAR_H2C_FW_PWRMODE:
1616 {
1617 u8 psmode = (*(u8 *)val);
1618
1619 /* Forece leave RF low power mode for 1T1R to prevent conficting setting in Fw power */
1620 /* saving sequence. 2010.06.07. Added by tynli. Suggested by SD3 yschang. */
1621 if (psmode != PS_MODE_ACTIVE)
1622 ODM_RF_Saving(podmpriv, true);
1623 rtl8188e_set_FwPwrMode_cmd(Adapter, psmode);
1624 }
1625 break;
1626 case HW_VAR_H2C_FW_JOINBSSRPT:
1627 {
1628 u8 mstatus = (*(u8 *)val);
1629
1630 rtl8188e_set_FwJoinBssReport_cmd(Adapter, mstatus);
1631 }
1632 break;
1633 case HW_VAR_INITIAL_GAIN:
1634 {
1635 struct rtw_dig *pDigTable = &podmpriv->DM_DigTable;
1636 u32 rx_gain = ((u32 *)(val))[0];
1637
1638 if (rx_gain == 0xff) {/* restore rx gain */
1639 ODM_Write_DIG(podmpriv, pDigTable->BackupIGValue);
1640 } else {
1641 pDigTable->BackupIGValue = pDigTable->CurIGValue;
1642 ODM_Write_DIG(podmpriv, rx_gain);
1643 }
1644 }
1645 break;
1646 case HW_VAR_TRIGGER_GPIO_0:
1647 rtl8192cu_trigger_gpio_0(Adapter);
1648 break;
1649 case HW_VAR_RPT_TIMER_SETTING:
1650 {
1651 u16 min_rpt_time = (*(u16 *)val);
1652
1653 ODM_RA_Set_TxRPT_Time(podmpriv, min_rpt_time);
1654 }
1655 break;
1656 case HW_VAR_ANTENNA_DIVERSITY_SELECT:
1657 {
1658 u8 Optimum_antenna = (*(u8 *)val);
1659 u8 Ant;
1660 /* switch antenna to Optimum_antenna */
1661 if (haldata->CurAntenna != Optimum_antenna) {
1662 Ant = (Optimum_antenna == 2) ? MAIN_ANT : AUX_ANT;
1663 rtl88eu_dm_update_rx_idle_ant(&haldata->odmpriv, Ant);
1664
1665 haldata->CurAntenna = Optimum_antenna;
1666 }
1667 }
1668 break;
1669 case HW_VAR_EFUSE_BYTES: /* To set EFUE total used bytes, added by Roger, 2008.12.22. */
1670 haldata->EfuseUsedBytes = *((u16 *)val);
1671 break;
1672 case HW_VAR_FIFO_CLEARN_UP:
1673 {
1674 struct pwrctrl_priv *pwrpriv = &Adapter->pwrctrlpriv;
1675 u8 trycnt = 100;
1676
1677 /* pause tx */
1678 usb_write8(Adapter, REG_TXPAUSE, 0xff);
1679
1680 /* keep sn */
1681 Adapter->xmitpriv.nqos_ssn = usb_read16(Adapter, REG_NQOS_SEQ);
1682
1683 if (!pwrpriv->bkeepfwalive) {
1684 /* RX DMA stop */
1685 usb_write32(Adapter, REG_RXPKT_NUM, (usb_read32(Adapter, REG_RXPKT_NUM) | RW_RELEASE_EN));
1686 do {
1687 if (!(usb_read32(Adapter, REG_RXPKT_NUM) & RXDMA_IDLE))
1688 break;
1689 } while (trycnt--);
1690 if (trycnt == 0)
1691 DBG_88E("Stop RX DMA failed......\n");
1692
1693 /* RQPN Load 0 */
1694 usb_write16(Adapter, REG_RQPN_NPQ, 0x0);
1695 usb_write32(Adapter, REG_RQPN, 0x80000000);
1696 mdelay(10);
1697 }
1698 }
1699 break;
1700 case HW_VAR_CHECK_TXBUF:
1701 break;
1702 case HW_VAR_APFM_ON_MAC:
1703 haldata->bMacPwrCtrlOn = *val;
1704 DBG_88E("%s: bMacPwrCtrlOn=%d\n", __func__, haldata->bMacPwrCtrlOn);
1705 break;
1706 case HW_VAR_TX_RPT_MAX_MACID:
1707 {
1708 u8 maxMacid = *val;
1709
1710 DBG_88E("### MacID(%d),Set Max Tx RPT MID(%d)\n", maxMacid, maxMacid + 1);
1711 usb_write8(Adapter, REG_TX_RPT_CTRL + 1, maxMacid + 1);
1712 }
1713 break;
1714 case HW_VAR_H2C_MEDIA_STATUS_RPT:
1715 rtl8188e_set_FwMediaStatus_cmd(Adapter, (*(__le16 *)val));
1716 break;
1717 case HW_VAR_BCN_VALID:
1718 /* BCN_VALID, BIT16 of REG_TDECTRL = BIT0 of REG_TDECTRL+2, write 1 to clear, Clear by sw */
1719 usb_write8(Adapter, REG_TDECTRL + 2, usb_read8(Adapter, REG_TDECTRL + 2) | BIT(0));
1720 break;
1721 default:
1722 break;
1723 }
1724 }
1725
rtw_hal_get_hwreg(struct adapter * Adapter,u8 variable,u8 * val)1726 void rtw_hal_get_hwreg(struct adapter *Adapter, u8 variable, u8 *val)
1727 {
1728 switch (variable) {
1729 case HW_VAR_BASIC_RATE:
1730 *((u16 *)(val)) = Adapter->HalData->BasicRateSet;
1731 /* fall through */
1732 case HW_VAR_TXPAUSE:
1733 val[0] = usb_read8(Adapter, REG_TXPAUSE);
1734 break;
1735 case HW_VAR_BCN_VALID:
1736 /* BCN_VALID, BIT16 of REG_TDECTRL = BIT0 of REG_TDECTRL+2 */
1737 val[0] = (BIT(0) & usb_read8(Adapter, REG_TDECTRL + 2)) ? true : false;
1738 break;
1739 case HW_VAR_FWLPS_RF_ON:
1740 {
1741 /* When we halt NIC, we should check if FW LPS is leave. */
1742 if (Adapter->pwrctrlpriv.rf_pwrstate == rf_off) {
1743 /* If it is in HW/SW Radio OFF or IPS state, we do not check Fw LPS Leave, */
1744 /* because Fw is unload. */
1745 val[0] = true;
1746 } else {
1747 u32 valRCR;
1748
1749 valRCR = usb_read32(Adapter, REG_RCR);
1750 valRCR &= 0x00070000;
1751 if (valRCR)
1752 val[0] = false;
1753 else
1754 val[0] = true;
1755 }
1756 }
1757 break;
1758 case HW_VAR_CURRENT_ANTENNA:
1759 val[0] = Adapter->HalData->CurAntenna;
1760 break;
1761 case HW_VAR_EFUSE_BYTES: /* To get EFUE total used bytes, added by Roger, 2008.12.22. */
1762 *((u16 *)(val)) = Adapter->HalData->EfuseUsedBytes;
1763 break;
1764 case HW_VAR_APFM_ON_MAC:
1765 *val = Adapter->HalData->bMacPwrCtrlOn;
1766 break;
1767 case HW_VAR_CHK_HI_QUEUE_EMPTY:
1768 *val = ((usb_read32(Adapter, REG_HGQ_INFORMATION) & 0x0000ff00) == 0) ? true : false;
1769 break;
1770 default:
1771 break;
1772 }
1773 }
1774
1775 /* */
1776 /* Description: */
1777 /* Query setting of specified variable. */
1778 /* */
rtw_hal_get_def_var(struct adapter * Adapter,enum hal_def_variable eVariable,void * pValue)1779 u8 rtw_hal_get_def_var(struct adapter *Adapter, enum hal_def_variable eVariable,
1780 void *pValue)
1781 {
1782 struct hal_data_8188e *haldata = Adapter->HalData;
1783 u8 bResult = _SUCCESS;
1784
1785 switch (eVariable) {
1786 case HAL_DEF_UNDERCORATEDSMOOTHEDPWDB:
1787 {
1788 struct mlme_priv *pmlmepriv = &Adapter->mlmepriv;
1789 struct sta_priv *pstapriv = &Adapter->stapriv;
1790 struct sta_info *psta;
1791
1792 psta = rtw_get_stainfo(pstapriv, pmlmepriv->cur_network.network.MacAddress);
1793 if (psta)
1794 *((int *)pValue) = psta->rssi_stat.UndecoratedSmoothedPWDB;
1795 }
1796 break;
1797 case HAL_DEF_IS_SUPPORT_ANT_DIV:
1798 *((u8 *)pValue) = (haldata->AntDivCfg == 0) ? false : true;
1799 break;
1800 case HAL_DEF_CURRENT_ANTENNA:
1801 *((u8 *)pValue) = haldata->CurAntenna;
1802 break;
1803 case HAL_DEF_DRVINFO_SZ:
1804 *((u32 *)pValue) = DRVINFO_SZ;
1805 break;
1806 case HAL_DEF_MAX_RECVBUF_SZ:
1807 *((u32 *)pValue) = MAX_RECVBUF_SZ;
1808 break;
1809 case HAL_DEF_RX_PACKET_OFFSET:
1810 *((u32 *)pValue) = RXDESC_SIZE + DRVINFO_SZ;
1811 break;
1812 case HAL_DEF_DBG_DM_FUNC:
1813 *((u32 *)pValue) = haldata->odmpriv.SupportAbility;
1814 break;
1815 case HAL_DEF_RA_DECISION_RATE:
1816 {
1817 u8 MacID = *((u8 *)pValue);
1818
1819 *((u8 *)pValue) = ODM_RA_GetDecisionRate_8188E(&haldata->odmpriv, MacID);
1820 }
1821 break;
1822 case HAL_DEF_RA_SGI:
1823 {
1824 u8 MacID = *((u8 *)pValue);
1825
1826 *((u8 *)pValue) = ODM_RA_GetShortGI_8188E(&haldata->odmpriv, MacID);
1827 }
1828 break;
1829 case HAL_DEF_PT_PWR_STATUS:
1830 {
1831 u8 MacID = *((u8 *)pValue);
1832
1833 *((u8 *)pValue) = ODM_RA_GetHwPwrStatus_8188E(&haldata->odmpriv, MacID);
1834 }
1835 break;
1836 case HW_VAR_MAX_RX_AMPDU_FACTOR:
1837 *((u32 *)pValue) = MAX_AMPDU_FACTOR_64K;
1838 break;
1839 case HW_DEF_RA_INFO_DUMP:
1840 {
1841 u8 entry_id = *((u8 *)pValue);
1842
1843 if (check_fwstate(&Adapter->mlmepriv, _FW_LINKED)) {
1844 DBG_88E("============ RA status check ===================\n");
1845 DBG_88E("Mac_id:%d , RateID = %d, RAUseRate = 0x%08x, RateSGI = %d, DecisionRate = 0x%02x ,PTStage = %d\n",
1846 entry_id,
1847 haldata->odmpriv.RAInfo[entry_id].RateID,
1848 haldata->odmpriv.RAInfo[entry_id].RAUseRate,
1849 haldata->odmpriv.RAInfo[entry_id].RateSGI,
1850 haldata->odmpriv.RAInfo[entry_id].DecisionRate,
1851 haldata->odmpriv.RAInfo[entry_id].PTStage);
1852 }
1853 }
1854 break;
1855 case HW_DEF_ODM_DBG_FLAG:
1856 {
1857 struct odm_dm_struct *dm_ocm = &haldata->odmpriv;
1858
1859 pr_info("dm_ocm->DebugComponents = 0x%llx\n", dm_ocm->DebugComponents);
1860 }
1861 break;
1862 case HAL_DEF_DBG_DUMP_RXPKT:
1863 *((u8 *)pValue) = haldata->bDumpRxPkt;
1864 break;
1865 case HAL_DEF_DBG_DUMP_TXPKT:
1866 *((u8 *)pValue) = haldata->bDumpTxPkt;
1867 break;
1868 default:
1869 bResult = _FAIL;
1870 break;
1871 }
1872
1873 return bResult;
1874 }
1875
UpdateHalRAMask8188EUsb(struct adapter * adapt,u32 mac_id,u8 rssi_level)1876 void UpdateHalRAMask8188EUsb(struct adapter *adapt, u32 mac_id, u8 rssi_level)
1877 {
1878 u8 init_rate = 0;
1879 u8 networkType, raid;
1880 u32 mask, rate_bitmap;
1881 u8 shortGIrate = false;
1882 int supportRateNum = 0;
1883 struct sta_info *psta;
1884 struct odm_dm_struct *odmpriv = &adapt->HalData->odmpriv;
1885 struct mlme_ext_priv *pmlmeext = &adapt->mlmeextpriv;
1886 struct mlme_ext_info *pmlmeinfo = &pmlmeext->mlmext_info;
1887 struct wlan_bssid_ex *cur_network = &pmlmeinfo->network;
1888
1889 if (mac_id >= NUM_STA) /* CAM_SIZE */
1890 return;
1891 psta = pmlmeinfo->FW_sta_info[mac_id].psta;
1892 if (!psta)
1893 return;
1894 switch (mac_id) {
1895 case 0:/* for infra mode */
1896 supportRateNum = rtw_get_rateset_len(cur_network->SupportedRates);
1897 networkType = judge_network_type(adapt, cur_network->SupportedRates, supportRateNum) & 0xf;
1898 raid = networktype_to_raid(networkType);
1899 mask = update_supported_rate(cur_network->SupportedRates, supportRateNum);
1900 mask |= (pmlmeinfo->HT_enable) ? update_MSC_rate(&pmlmeinfo->HT_caps) : 0;
1901 if (support_short_GI(adapt, &pmlmeinfo->HT_caps))
1902 shortGIrate = true;
1903 break;
1904 case 1:/* for broadcast/multicast */
1905 supportRateNum = rtw_get_rateset_len(pmlmeinfo->FW_sta_info[mac_id].SupportedRates);
1906 if (pmlmeext->cur_wireless_mode & WIRELESS_11B)
1907 networkType = WIRELESS_11B;
1908 else
1909 networkType = WIRELESS_11G;
1910 raid = networktype_to_raid(networkType);
1911 mask = update_basic_rate(cur_network->SupportedRates, supportRateNum);
1912 break;
1913 default: /* for each sta in IBSS */
1914 supportRateNum = rtw_get_rateset_len(pmlmeinfo->FW_sta_info[mac_id].SupportedRates);
1915 networkType = judge_network_type(adapt, pmlmeinfo->FW_sta_info[mac_id].SupportedRates, supportRateNum) & 0xf;
1916 raid = networktype_to_raid(networkType);
1917 mask = update_supported_rate(cur_network->SupportedRates, supportRateNum);
1918
1919 /* todo: support HT in IBSS */
1920 break;
1921 }
1922
1923 rate_bitmap = ODM_Get_Rate_Bitmap(odmpriv, mac_id, mask, rssi_level);
1924 DBG_88E("%s => mac_id:%d, networkType:0x%02x, mask:0x%08x\n\t ==> rssi_level:%d, rate_bitmap:0x%08x\n",
1925 __func__, mac_id, networkType, mask, rssi_level, rate_bitmap);
1926
1927 mask &= rate_bitmap;
1928
1929 init_rate = get_highest_rate_idx(mask) & 0x3f;
1930
1931 ODM_RA_UpdateRateInfo_8188E(odmpriv, mac_id, raid, mask, shortGIrate);
1932
1933 /* set ra_id */
1934 psta->raid = raid;
1935 psta->init_rate = init_rate;
1936 }
1937
beacon_timing_control(struct adapter * adapt)1938 void beacon_timing_control(struct adapter *adapt)
1939 {
1940 u32 value32;
1941 struct mlme_ext_priv *pmlmeext = &adapt->mlmeextpriv;
1942 struct mlme_ext_info *pmlmeinfo = &pmlmeext->mlmext_info;
1943 u32 bcn_ctrl_reg = REG_BCN_CTRL;
1944 /* reset TSF, enable update TSF, correcting TSF On Beacon */
1945
1946 /* BCN interval */
1947 usb_write16(adapt, REG_BCN_INTERVAL, pmlmeinfo->bcn_interval);
1948 usb_write8(adapt, REG_ATIMWND, 0x02);/* 2ms */
1949
1950 _InitBeaconParameters(adapt);
1951
1952 usb_write8(adapt, REG_SLOT, 0x09);
1953
1954 value32 = usb_read32(adapt, REG_TCR);
1955 value32 &= ~TSFRST;
1956 usb_write32(adapt, REG_TCR, value32);
1957
1958 value32 |= TSFRST;
1959 usb_write32(adapt, REG_TCR, value32);
1960
1961 /* NOTE: Fix test chip's bug (about contention windows's randomness) */
1962 usb_write8(adapt, REG_RXTSF_OFFSET_CCK, 0x50);
1963 usb_write8(adapt, REG_RXTSF_OFFSET_OFDM, 0x50);
1964
1965 _BeaconFunctionEnable(adapt, true, true);
1966
1967 ResumeTxBeacon(adapt);
1968
1969 usb_write8(adapt, bcn_ctrl_reg, usb_read8(adapt, bcn_ctrl_reg) | BIT(1));
1970 }
1971
rtw_hal_def_value_init(struct adapter * adapt)1972 void rtw_hal_def_value_init(struct adapter *adapt)
1973 {
1974 struct hal_data_8188e *haldata = adapt->HalData;
1975 struct pwrctrl_priv *pwrctrlpriv;
1976 u8 i;
1977
1978 pwrctrlpriv = &adapt->pwrctrlpriv;
1979
1980 /* init default value */
1981 if (!pwrctrlpriv->bkeepfwalive)
1982 haldata->LastHMEBoxNum = 0;
1983
1984 /* init dm default value */
1985 haldata->odmpriv.RFCalibrateInfo.bIQKInitialized = false;
1986 haldata->odmpriv.RFCalibrateInfo.TM_Trigger = 0;/* for IQK */
1987 haldata->pwrGroupCnt = 0;
1988 haldata->PGMaxGroup = 13;
1989 haldata->odmpriv.RFCalibrateInfo.ThermalValue_HP_index = 0;
1990 for (i = 0; i < HP_THERMAL_NUM; i++)
1991 haldata->odmpriv.RFCalibrateInfo.ThermalValue_HP[i] = 0;
1992 }
1993