1/* 2 * BSD LICENSE 3 * 4 * Copyright(c) 2016 Broadcom. All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 10 * * Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * * Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in 14 * the documentation and/or other materials provided with the 15 * distribution. 16 * * Neither the name of Broadcom Corporation nor the names of its 17 * contributors may be used to endorse or promote products derived 18 * from this software without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 21 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 22 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 23 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 24 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 25 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 26 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 27 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 28 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 31 */ 32 33/dts-v1/; 34 35#include "bcm-nsp.dtsi" 36#include <dt-bindings/gpio/gpio.h> 37 38/ { 39 model = "NorthStar Plus SVK (BCM958623HR)"; 40 compatible = "brcm,bcm58623", "brcm,nsp"; 41 42 chosen { 43 stdout-path = "serial0:115200n8"; 44 }; 45 46 memory@60000000 { 47 device_type = "memory"; 48 reg = <0x60000000 0x80000000>; 49 }; 50 51 gpio-restart { 52 compatible = "gpio-restart"; 53 gpios = <&gpioa 15 GPIO_ACTIVE_LOW>; 54 open-source; 55 priority = <200>; 56 }; 57}; 58 59/* USB 3 and SLIC support needed to be complete */ 60 61&amac0 { 62 status = "okay"; 63}; 64 65&amac1 { 66 status = "okay"; 67}; 68 69&amac2 { 70 status = "okay"; 71}; 72 73&ehci0 { 74 status = "okay"; 75}; 76 77&nand_controller { 78 nand@0 { 79 compatible = "brcm,nandcs"; 80 reg = <0>; 81 nand-on-flash-bbt; 82 83 #address-cells = <1>; 84 #size-cells = <1>; 85 86 nand-ecc-strength = <24>; 87 nand-ecc-step-size = <1024>; 88 89 brcm,nand-oob-sector-size = <27>; 90 91 partition@0 { 92 label = "nboot"; 93 reg = <0x00000000 0x00200000>; 94 read-only; 95 }; 96 partition@200000 { 97 label = "nenv"; 98 reg = <0x00200000 0x00400000>; 99 }; 100 partition@600000 { 101 label = "nsystem"; 102 reg = <0x00600000 0x00a00000>; 103 }; 104 partition@1000000 { 105 label = "nrootfs"; 106 reg = <0x01000000 0x03000000>; 107 }; 108 partition@4000000 { 109 label = "ncustfs"; 110 reg = <0x04000000 0x3c000000>; 111 }; 112 }; 113}; 114 115&ohci0 { 116 status = "okay"; 117}; 118 119&pcie0 { 120 status = "okay"; 121}; 122 123&pcie1 { 124 status = "okay"; 125}; 126 127&pinctrl { 128 pinctrl-names = "default"; 129 pinctrl-0 = <&nand_sel>; 130 nand_sel: nand_sel { 131 function = "nand"; 132 groups = "nand_grp"; 133 }; 134}; 135 136&sata_phy0 { 137 status = "okay"; 138}; 139 140&qspi { 141 bspi-sel = <0>; 142 flash: m25p80@0 { 143 #address-cells = <1>; 144 #size-cells = <1>; 145 compatible = "m25p80"; 146 reg = <0x0>; 147 spi-max-frequency = <12500000>; 148 m25p,fast-read; 149 spi-cpol; 150 spi-cpha; 151 152 partition@0 { 153 label = "boot"; 154 reg = <0x00000000 0x000a0000>; 155 }; 156 157 partition@a0000 { 158 label = "env"; 159 reg = <0x000a0000 0x00060000>; 160 }; 161 162 partition@100000 { 163 label = "system"; 164 reg = <0x00100000 0x00600000>; 165 }; 166 167 partition@700000 { 168 label = "rootfs"; 169 reg = <0x00700000 0x01900000>; 170 }; 171 }; 172}; 173 174&srab { 175 compatible = "brcm,bcm58623-srab", "brcm,nsp-srab"; 176 status = "okay"; 177 178 ports { 179 #address-cells = <1>; 180 #size-cells = <0>; 181 182 port@0 { 183 label = "port0"; 184 reg = <0>; 185 }; 186 187 port@1 { 188 label = "port1"; 189 reg = <1>; 190 }; 191 192 port@2 { 193 label = "port2"; 194 reg = <2>; 195 }; 196 197 port@3 { 198 label = "port3"; 199 reg = <3>; 200 }; 201 202 port@4 { 203 label = "port4"; 204 reg = <4>; 205 }; 206 207 port@8 { 208 ethernet = <&amac2>; 209 label = "cpu"; 210 reg = <8>; 211 fixed-link { 212 speed = <1000>; 213 full-duplex; 214 }; 215 }; 216 }; 217}; 218 219&uart0 { 220 status = "okay"; 221}; 222 223&usb3_phy { 224 status = "okay"; 225}; 226 227&xhci { 228 status = "okay"; 229}; 230