1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * TQM5200 board Device Tree Source 4 * 5 * Copyright (C) 2007 Semihalf 6 * Marian Balakowicz <m8@semihalf.com> 7 */ 8 9/dts-v1/; 10 11/ { 12 model = "tqc,tqm5200"; 13 compatible = "tqc,tqm5200"; 14 #address-cells = <1>; 15 #size-cells = <1>; 16 interrupt-parent = <&mpc5200_pic>; 17 18 cpus { 19 #address-cells = <1>; 20 #size-cells = <0>; 21 22 PowerPC,5200@0 { 23 device_type = "cpu"; 24 reg = <0>; 25 d-cache-line-size = <32>; 26 i-cache-line-size = <32>; 27 d-cache-size = <0x4000>; // L1, 16K 28 i-cache-size = <0x4000>; // L1, 16K 29 timebase-frequency = <0>; // from bootloader 30 bus-frequency = <0>; // from bootloader 31 clock-frequency = <0>; // from bootloader 32 }; 33 }; 34 35 memory@0 { 36 device_type = "memory"; 37 reg = <0x00000000 0x04000000>; // 64MB 38 }; 39 40 soc5200@f0000000 { 41 #address-cells = <1>; 42 #size-cells = <1>; 43 compatible = "fsl,mpc5200-immr"; 44 ranges = <0 0xf0000000 0x0000c000>; 45 reg = <0xf0000000 0x00000100>; 46 bus-frequency = <0>; // from bootloader 47 system-frequency = <0>; // from bootloader 48 49 cdm@200 { 50 compatible = "fsl,mpc5200-cdm"; 51 reg = <0x200 0x38>; 52 }; 53 54 mpc5200_pic: interrupt-controller@500 { 55 // 5200 interrupts are encoded into two levels; 56 interrupt-controller; 57 #interrupt-cells = <3>; 58 compatible = "fsl,mpc5200-pic"; 59 reg = <0x500 0x80>; 60 }; 61 62 timer@600 { // General Purpose Timer 63 compatible = "fsl,mpc5200-gpt"; 64 reg = <0x600 0x10>; 65 interrupts = <1 9 0>; 66 fsl,has-wdt; 67 }; 68 69 can@900 { 70 compatible = "fsl,mpc5200-mscan"; 71 interrupts = <2 17 0>; 72 reg = <0x900 0x80>; 73 }; 74 75 can@980 { 76 compatible = "fsl,mpc5200-mscan"; 77 interrupts = <2 18 0>; 78 reg = <0x980 0x80>; 79 }; 80 81 gpio_simple: gpio@b00 { 82 compatible = "fsl,mpc5200-gpio"; 83 reg = <0xb00 0x40>; 84 interrupts = <1 7 0>; 85 gpio-controller; 86 #gpio-cells = <2>; 87 }; 88 89 usb@1000 { 90 compatible = "fsl,mpc5200-ohci","ohci-be"; 91 reg = <0x1000 0xff>; 92 interrupts = <2 6 0>; 93 }; 94 95 dma-controller@1200 { 96 compatible = "fsl,mpc5200-bestcomm"; 97 reg = <0x1200 0x80>; 98 interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 99 3 4 0 3 5 0 3 6 0 3 7 0 100 3 8 0 3 9 0 3 10 0 3 11 0 101 3 12 0 3 13 0 3 14 0 3 15 0>; 102 }; 103 104 xlb@1f00 { 105 compatible = "fsl,mpc5200-xlb"; 106 reg = <0x1f00 0x100>; 107 }; 108 109 serial@2000 { // PSC1 110 compatible = "fsl,mpc5200-psc-uart"; 111 reg = <0x2000 0x100>; 112 interrupts = <2 1 0>; 113 }; 114 115 serial@2200 { // PSC2 116 compatible = "fsl,mpc5200-psc-uart"; 117 reg = <0x2200 0x100>; 118 interrupts = <2 2 0>; 119 }; 120 121 serial@2400 { // PSC3 122 compatible = "fsl,mpc5200-psc-uart"; 123 reg = <0x2400 0x100>; 124 interrupts = <2 3 0>; 125 }; 126 127 ethernet@3000 { 128 compatible = "fsl,mpc5200-fec"; 129 reg = <0x3000 0x400>; 130 local-mac-address = [ 00 00 00 00 00 00 ]; 131 interrupts = <2 5 0>; 132 phy-handle = <&phy0>; 133 }; 134 135 mdio@3000 { 136 #address-cells = <1>; 137 #size-cells = <0>; 138 compatible = "fsl,mpc5200-mdio"; 139 reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts 140 interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. 141 142 phy0: ethernet-phy@0 { 143 reg = <0>; 144 }; 145 }; 146 147 ata@3a00 { 148 compatible = "fsl,mpc5200-ata"; 149 reg = <0x3a00 0x100>; 150 interrupts = <2 7 0>; 151 }; 152 153 i2c@3d40 { 154 #address-cells = <1>; 155 #size-cells = <0>; 156 compatible = "fsl,mpc5200-i2c","fsl-i2c"; 157 reg = <0x3d40 0x40>; 158 interrupts = <2 16 0>; 159 160 rtc@68 { 161 compatible = "dallas,ds1307"; 162 reg = <0x68>; 163 }; 164 }; 165 166 sram@8000 { 167 compatible = "fsl,mpc5200-sram"; 168 reg = <0x8000 0x4000>; 169 }; 170 }; 171 172 localbus { 173 compatible = "fsl,mpc5200-lpb","simple-bus"; 174 #address-cells = <2>; 175 #size-cells = <1>; 176 ranges = <0 0 0xfc000000 0x02000000>; 177 178 flash@0,0 { 179 compatible = "cfi-flash"; 180 reg = <0 0 0x02000000>; 181 bank-width = <4>; 182 device-width = <2>; 183 #size-cells = <1>; 184 #address-cells = <1>; 185 }; 186 }; 187 188 pci@f0000d00 { 189 #interrupt-cells = <1>; 190 #size-cells = <2>; 191 #address-cells = <3>; 192 device_type = "pci"; 193 compatible = "fsl,mpc5200-pci"; 194 reg = <0xf0000d00 0x100>; 195 interrupt-map-mask = <0xf800 0 0 7>; 196 interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 197 0xc000 0 0 2 &mpc5200_pic 0 0 3 198 0xc000 0 0 3 &mpc5200_pic 0 0 3 199 0xc000 0 0 4 &mpc5200_pic 0 0 3>; 200 clock-frequency = <0>; // From boot loader 201 interrupts = <2 8 0 2 9 0 2 10 0>; 202 bus-range = <0 0>; 203 ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000 204 0x02000000 0 0x90000000 0x90000000 0 0x10000000 205 0x01000000 0 0x00000000 0xa0000000 0 0x01000000>; 206 }; 207}; 208