1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * Device Tree file for Synology DS213j 4 * 5 * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org> 6 * 7 * Note: this Device Tree assumes that the bootloader has remapped the 8 * internal registers to 0xf1000000 (instead of the old 0xd0000000). 9 * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot 10 * bootloaders provided by Marvell. It is used in recent versions of 11 * DSM software provided by Synology. Nonetheless, some earlier boards 12 * were delivered with an older version of u-boot that left internal 13 * registers mapped at 0xd0000000. If you have such a device you will 14 * not be able to directly boot a kernel based on this Device Tree. In 15 * that case, the preferred solution is to update your bootloader (e.g. 16 * by upgrading to latest version of DSM, or building a new one and 17 * installing it from u-boot prompt) or adjust the Devive Tree 18 * (s/0xf1000000/0xd0000000/ in 'ranges' below). 19 */ 20 21/dts-v1/; 22 23#include <dt-bindings/input/input.h> 24#include <dt-bindings/gpio/gpio.h> 25#include "armada-370.dtsi" 26 27/ { 28 model = "Synology DS213j"; 29 compatible = "synology,ds213j", "marvell,armada370", 30 "marvell,armada-370-xp"; 31 32 chosen { 33 stdout-path = "serial0:115200n8"; 34 }; 35 36 memory@0 { 37 device_type = "memory"; 38 reg = <0x00000000 0x20000000>; /* 512 MB */ 39 }; 40 41 soc { 42 ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 43 MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 44 MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; 45 46 internal-regs { 47 48 /* RTC provided by Seiko S-35390A I2C RTC chip below */ 49 rtc@10300 { 50 status = "disabled"; 51 }; 52 53 i2c@11000 { 54 compatible = "marvell,mv64xxx-i2c"; 55 pinctrl-0 = <&i2c0_pins>; 56 pinctrl-names = "default"; 57 clock-frequency = <400000>; 58 status = "okay"; 59 60 /* Main device RTC chip */ 61 s35390a: s35390a@30 { 62 compatible = "sii,s35390a"; 63 reg = <0x30>; 64 }; 65 }; 66 67 /* Connected to a header on device's PCB */ 68 serial@12000 { 69 status = "okay"; 70 }; 71 72 /* Connected to a TI MSP430F2111 for power control */ 73 serial@12100 { 74 status = "okay"; 75 }; 76 77 poweroff@12100 { 78 compatible = "synology,power-off"; 79 reg = <0x12100 0x100>; 80 clocks = <&coreclk 0>; 81 }; 82 83 /* rear USB port, near reset button */ 84 usb@50000 { 85 status = "okay"; 86 }; 87 88 /* rear USB port, near RJ45 port */ 89 usb@51000 { 90 status = "okay"; 91 }; 92 93 ethernet@70000 { 94 status = "okay"; 95 phy = <&phy1>; 96 phy-mode = "sgmii"; 97 }; 98 99 sata@a0000 { 100 nr-ports = <2>; 101 status = "okay"; 102 }; 103 }; 104 }; 105 106 gpio-fan-32-38 { 107 status = "okay"; 108 compatible = "gpio-fan"; 109 pinctrl-0 = <&fan_ctrl_low_pin &fan_ctrl_mid_pin 110 &fan_ctrl_high_pin &fan_alarm_pin>; 111 pinctrl-names = "default"; 112 gpios = <&gpio1 31 GPIO_ACTIVE_HIGH 113 &gpio2 0 GPIO_ACTIVE_HIGH 114 &gpio2 1 GPIO_ACTIVE_HIGH>; 115 alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; 116 gpio-fan,speed-map = < 0 0 117 1000 1 118 1150 2 119 1350 4 120 1500 3 121 1650 5 122 1750 6 123 1900 7 >; 124 }; 125 126 gpio-leds { 127 compatible = "gpio-leds"; 128 pinctrl-0 = <&disk1_led_pin 129 &disk2_led_pin>; 130 pinctrl-names = "default"; 131 132 disk1-led-amber { 133 label = "synology:amber:disk1"; 134 gpios = <&gpio0 31 GPIO_ACTIVE_LOW>; 135 default-state = "keep"; 136 }; 137 138 disk2-led-amber { 139 label = "synology:amber:disk2"; 140 gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; 141 default-state = "keep"; 142 }; 143 }; 144 145 regulators { 146 compatible = "simple-bus"; 147 #address-cells = <1>; 148 #size-cells = <0>; 149 pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>; 150 pinctrl-names = "default"; 151 152 sata1_regulator: sata1-regulator@1 { 153 compatible = "regulator-fixed"; 154 reg = <1>; 155 regulator-name = "SATA1 Power"; 156 regulator-min-microvolt = <5000000>; 157 regulator-max-microvolt = <5000000>; 158 startup-delay-us = <2000000>; 159 enable-active-high; 160 regulator-always-on; 161 regulator-boot-on; 162 gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; 163 }; 164 165 sata2_regulator: sata2-regulator@2 { 166 compatible = "regulator-fixed"; 167 reg = <2>; 168 regulator-name = "SATA2 Power"; 169 regulator-min-microvolt = <5000000>; 170 regulator-max-microvolt = <5000000>; 171 startup-delay-us = <4000000>; 172 enable-active-high; 173 regulator-always-on; 174 regulator-boot-on; 175 gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>; 176 }; 177 }; 178}; 179 180&mdio { 181 phy1: ethernet-phy@1 { /* Marvell 88E1512 */ 182 reg = <1>; 183 }; 184}; 185 186&pinctrl { 187 disk1_led_pin: disk1-led-pin { 188 marvell,pins = "mpp31"; 189 marvell,function = "gpio"; 190 }; 191 192 disk2_led_pin: disk2-led-pin { 193 marvell,pins = "mpp32"; 194 marvell,function = "gpio"; 195 }; 196 197 sata1_pwr_pin: sata1-pwr-pin { 198 marvell,pins = "mpp37"; 199 marvell,function = "gpio"; 200 }; 201 202 sata2_pwr_pin: sata2-pwr-pin { 203 marvell,pins = "mpp62"; 204 marvell,function = "gpio"; 205 }; 206 207 sata1_pres_pin: sata1-pres-pin { 208 marvell,pins = "mpp60"; 209 marvell,function = "gpio"; 210 }; 211 212 sata2_pres_pin: sata2-pres-pin { 213 marvell,pins = "mpp48"; 214 marvell,function = "gpio"; 215 }; 216 217 syno_id_bit0_pin: syno-id-bit0-pin { 218 marvell,pins = "mpp55"; 219 marvell,function = "gpio"; 220 }; 221 222 syno_id_bit1_pin: syno-id-bit1-pin { 223 marvell,pins = "mpp56"; 224 marvell,function = "gpio"; 225 }; 226 227 syno_id_bit2_pin: syno-id-bit2-pin { 228 marvell,pins = "mpp57"; 229 marvell,function = "gpio"; 230 }; 231 232 syno_id_bit3_pin: syno-id-bit3-pin { 233 marvell,pins = "mpp58"; 234 marvell,function = "gpio"; 235 }; 236 237 fan_ctrl_low_pin: fan-ctrl-low-pin { 238 marvell,pins = "mpp65"; 239 marvell,function = "gpio"; 240 }; 241 242 fan_ctrl_mid_pin: fan-ctrl-mid-pin { 243 marvell,pins = "mpp64"; 244 marvell,function = "gpio"; 245 }; 246 247 fan_ctrl_high_pin: fan-ctrl-high-pin { 248 marvell,pins = "mpp63"; 249 marvell,function = "gpio"; 250 }; 251 252 fan_alarm_pin: fan-alarm-pin { 253 marvell,pins = "mpp38"; 254 marvell,function = "gpio"; 255 }; 256}; 257 258&spi0 { 259 status = "okay"; 260 261 spi-flash@0 { 262 #address-cells = <1>; 263 #size-cells = <1>; 264 compatible = "micron,n25q064", "jedec,spi-nor"; 265 reg = <0>; /* Chip select 0 */ 266 spi-max-frequency = <20000000>; 267 268 /* 269 * Warning! 270 * 271 * Synology u-boot uses its compiled-in environment 272 * and it seems Synology did not care to change u-boot 273 * default configuration in order to allow saving a 274 * modified environment at a sensible location. So, 275 * if you do a 'saveenv' under u-boot, your modified 276 * environment will be saved at 1MB after the start 277 * of the flash, i.e. in the middle of the uImage. 278 * For that reason, it is strongly advised not to 279 * change the default environment, unless you know 280 * what you are doing. 281 */ 282 partition@0 { /* u-boot */ 283 label = "RedBoot"; 284 reg = <0x00000000 0x000c0000>; /* 768KB */ 285 }; 286 287 partition@c0000 { /* uImage */ 288 label = "zImage"; 289 reg = <0x000c0000 0x002d0000>; /* 2880KB */ 290 }; 291 292 partition@390000 { /* uInitramfs */ 293 label = "rd.gz"; 294 reg = <0x00390000 0x00440000>; /* 4250KB */ 295 }; 296 297 partition@7d0000 { /* MAC address and serial number */ 298 label = "vendor"; 299 reg = <0x007d0000 0x00010000>; /* 64KB */ 300 }; 301 302 partition@7e0000 { 303 label = "RedBoot config"; 304 reg = <0x007e0000 0x00010000>; /* 64KB */ 305 }; 306 307 partition@7f0000 { 308 label = "FIS directory"; 309 reg = <0x007f0000 0x00010000>; /* 64KB */ 310 }; 311 }; 312}; 313