1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Driver for Linear Technology LTC4215 I2C Hot Swap Controller
4 *
5 * Copyright (C) 2009 Ira W. Snyder <iws@ovro.caltech.edu>
6 *
7 * Datasheet:
8 * http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1163,P17572,D12697
9 */
10
11 #include <linux/kernel.h>
12 #include <linux/module.h>
13 #include <linux/init.h>
14 #include <linux/err.h>
15 #include <linux/slab.h>
16 #include <linux/i2c.h>
17 #include <linux/hwmon.h>
18 #include <linux/hwmon-sysfs.h>
19 #include <linux/jiffies.h>
20
21 /* Here are names of the chip's registers (a.k.a. commands) */
22 enum ltc4215_cmd {
23 LTC4215_CONTROL = 0x00, /* rw */
24 LTC4215_ALERT = 0x01, /* rw */
25 LTC4215_STATUS = 0x02, /* ro */
26 LTC4215_FAULT = 0x03, /* rw */
27 LTC4215_SENSE = 0x04, /* rw */
28 LTC4215_SOURCE = 0x05, /* rw */
29 LTC4215_ADIN = 0x06, /* rw */
30 };
31
32 struct ltc4215_data {
33 struct i2c_client *client;
34
35 struct mutex update_lock;
36 bool valid;
37 unsigned long last_updated; /* in jiffies */
38
39 /* Registers */
40 u8 regs[7];
41 };
42
ltc4215_update_device(struct device * dev)43 static struct ltc4215_data *ltc4215_update_device(struct device *dev)
44 {
45 struct ltc4215_data *data = dev_get_drvdata(dev);
46 struct i2c_client *client = data->client;
47 s32 val;
48 int i;
49
50 mutex_lock(&data->update_lock);
51
52 /* The chip's A/D updates 10 times per second */
53 if (time_after(jiffies, data->last_updated + HZ / 10) || !data->valid) {
54
55 dev_dbg(&client->dev, "Starting ltc4215 update\n");
56
57 /* Read all registers */
58 for (i = 0; i < ARRAY_SIZE(data->regs); i++) {
59 val = i2c_smbus_read_byte_data(client, i);
60 if (unlikely(val < 0))
61 data->regs[i] = 0;
62 else
63 data->regs[i] = val;
64 }
65
66 data->last_updated = jiffies;
67 data->valid = 1;
68 }
69
70 mutex_unlock(&data->update_lock);
71
72 return data;
73 }
74
75 /* Return the voltage from the given register in millivolts */
ltc4215_get_voltage(struct device * dev,u8 reg)76 static int ltc4215_get_voltage(struct device *dev, u8 reg)
77 {
78 struct ltc4215_data *data = ltc4215_update_device(dev);
79 const u8 regval = data->regs[reg];
80 u32 voltage = 0;
81
82 switch (reg) {
83 case LTC4215_SENSE:
84 /* 151 uV per increment */
85 voltage = regval * 151 / 1000;
86 break;
87 case LTC4215_SOURCE:
88 /* 60.5 mV per increment */
89 voltage = regval * 605 / 10;
90 break;
91 case LTC4215_ADIN:
92 /*
93 * The ADIN input is divided by 12.5, and has 4.82 mV
94 * per increment, so we have the additional multiply
95 */
96 voltage = regval * 482 * 125 / 1000;
97 break;
98 default:
99 /* If we get here, the developer messed up */
100 WARN_ON_ONCE(1);
101 break;
102 }
103
104 return voltage;
105 }
106
107 /* Return the current from the sense resistor in mA */
ltc4215_get_current(struct device * dev)108 static unsigned int ltc4215_get_current(struct device *dev)
109 {
110 struct ltc4215_data *data = ltc4215_update_device(dev);
111
112 /*
113 * The strange looking conversions that follow are fixed-point
114 * math, since we cannot do floating point in the kernel.
115 *
116 * Step 1: convert sense register to microVolts
117 * Step 2: convert voltage to milliAmperes
118 *
119 * If you play around with the V=IR equation, you come up with
120 * the following: X uV / Y mOhm == Z mA
121 *
122 * With the resistors that are fractions of a milliOhm, we multiply
123 * the voltage and resistance by 10, to shift the decimal point.
124 * Now we can use the normal division operator again.
125 */
126
127 /* Calculate voltage in microVolts (151 uV per increment) */
128 const unsigned int voltage = data->regs[LTC4215_SENSE] * 151;
129
130 /* Calculate current in milliAmperes (4 milliOhm sense resistor) */
131 const unsigned int curr = voltage / 4;
132
133 return curr;
134 }
135
ltc4215_voltage_show(struct device * dev,struct device_attribute * da,char * buf)136 static ssize_t ltc4215_voltage_show(struct device *dev,
137 struct device_attribute *da, char *buf)
138 {
139 struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
140 const int voltage = ltc4215_get_voltage(dev, attr->index);
141
142 return snprintf(buf, PAGE_SIZE, "%d\n", voltage);
143 }
144
ltc4215_current_show(struct device * dev,struct device_attribute * da,char * buf)145 static ssize_t ltc4215_current_show(struct device *dev,
146 struct device_attribute *da, char *buf)
147 {
148 const unsigned int curr = ltc4215_get_current(dev);
149
150 return snprintf(buf, PAGE_SIZE, "%u\n", curr);
151 }
152
ltc4215_power_show(struct device * dev,struct device_attribute * da,char * buf)153 static ssize_t ltc4215_power_show(struct device *dev,
154 struct device_attribute *da, char *buf)
155 {
156 const unsigned int curr = ltc4215_get_current(dev);
157 const int output_voltage = ltc4215_get_voltage(dev, LTC4215_ADIN);
158
159 /* current in mA * voltage in mV == power in uW */
160 const unsigned int power = abs(output_voltage * curr);
161
162 return snprintf(buf, PAGE_SIZE, "%u\n", power);
163 }
164
ltc4215_alarm_show(struct device * dev,struct device_attribute * da,char * buf)165 static ssize_t ltc4215_alarm_show(struct device *dev,
166 struct device_attribute *da, char *buf)
167 {
168 struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
169 struct ltc4215_data *data = ltc4215_update_device(dev);
170 const u8 reg = data->regs[LTC4215_STATUS];
171 const u32 mask = attr->index;
172
173 return snprintf(buf, PAGE_SIZE, "%u\n", !!(reg & mask));
174 }
175
176 /*
177 * These macros are used below in constructing device attribute objects
178 * for use with sysfs_create_group() to make a sysfs device file
179 * for each register.
180 */
181
182 /* Construct a sensor_device_attribute structure for each register */
183
184 /* Current */
185 static SENSOR_DEVICE_ATTR_RO(curr1_input, ltc4215_current, 0);
186 static SENSOR_DEVICE_ATTR_RO(curr1_max_alarm, ltc4215_alarm, 1 << 2);
187
188 /* Power (virtual) */
189 static SENSOR_DEVICE_ATTR_RO(power1_input, ltc4215_power, 0);
190
191 /* Input Voltage */
192 static SENSOR_DEVICE_ATTR_RO(in1_input, ltc4215_voltage, LTC4215_ADIN);
193 static SENSOR_DEVICE_ATTR_RO(in1_max_alarm, ltc4215_alarm, 1 << 0);
194 static SENSOR_DEVICE_ATTR_RO(in1_min_alarm, ltc4215_alarm, 1 << 1);
195
196 /* Output Voltage */
197 static SENSOR_DEVICE_ATTR_RO(in2_input, ltc4215_voltage, LTC4215_SOURCE);
198 static SENSOR_DEVICE_ATTR_RO(in2_min_alarm, ltc4215_alarm, 1 << 3);
199
200 /*
201 * Finally, construct an array of pointers to members of the above objects,
202 * as required for sysfs_create_group()
203 */
204 static struct attribute *ltc4215_attrs[] = {
205 &sensor_dev_attr_curr1_input.dev_attr.attr,
206 &sensor_dev_attr_curr1_max_alarm.dev_attr.attr,
207
208 &sensor_dev_attr_power1_input.dev_attr.attr,
209
210 &sensor_dev_attr_in1_input.dev_attr.attr,
211 &sensor_dev_attr_in1_max_alarm.dev_attr.attr,
212 &sensor_dev_attr_in1_min_alarm.dev_attr.attr,
213
214 &sensor_dev_attr_in2_input.dev_attr.attr,
215 &sensor_dev_attr_in2_min_alarm.dev_attr.attr,
216
217 NULL,
218 };
219 ATTRIBUTE_GROUPS(ltc4215);
220
ltc4215_probe(struct i2c_client * client)221 static int ltc4215_probe(struct i2c_client *client)
222 {
223 struct i2c_adapter *adapter = client->adapter;
224 struct device *dev = &client->dev;
225 struct ltc4215_data *data;
226 struct device *hwmon_dev;
227
228 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
229 return -ENODEV;
230
231 data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
232 if (!data)
233 return -ENOMEM;
234
235 data->client = client;
236 mutex_init(&data->update_lock);
237
238 /* Initialize the LTC4215 chip */
239 i2c_smbus_write_byte_data(client, LTC4215_FAULT, 0x00);
240
241 hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
242 data,
243 ltc4215_groups);
244 return PTR_ERR_OR_ZERO(hwmon_dev);
245 }
246
247 static const struct i2c_device_id ltc4215_id[] = {
248 { "ltc4215", 0 },
249 { }
250 };
251 MODULE_DEVICE_TABLE(i2c, ltc4215_id);
252
253 /* This is the driver that will be inserted */
254 static struct i2c_driver ltc4215_driver = {
255 .driver = {
256 .name = "ltc4215",
257 },
258 .probe_new = ltc4215_probe,
259 .id_table = ltc4215_id,
260 };
261
262 module_i2c_driver(ltc4215_driver);
263
264 MODULE_AUTHOR("Ira W. Snyder <iws@ovro.caltech.edu>");
265 MODULE_DESCRIPTION("LTC4215 driver");
266 MODULE_LICENSE("GPL");
267