1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * OMAP4-specific DPLL control functions
4 *
5 * Copyright (C) 2011 Texas Instruments, Inc.
6 * Rajendra Nayak
7 */
8
9 #include <linux/kernel.h>
10 #include <linux/errno.h>
11 #include <linux/clk.h>
12 #include <linux/io.h>
13 #include <linux/bitops.h>
14 #include <linux/clk/ti.h>
15
16 #include "clock.h"
17
18 /*
19 * Maximum DPLL input frequency (FINT) and output frequency (FOUT) that
20 * can supported when using the DPLL low-power mode. Frequencies are
21 * defined in OMAP4430/60 Public TRM section 3.6.3.3.2 "Enable Control,
22 * Status, and Low-Power Operation Mode".
23 */
24 #define OMAP4_DPLL_LP_FINT_MAX 1000000
25 #define OMAP4_DPLL_LP_FOUT_MAX 100000000
26
27 /*
28 * Bitfield declarations
29 */
30 #define OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK BIT(8)
31 #define OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK BIT(10)
32 #define OMAP4430_DPLL_REGM4XEN_MASK BIT(11)
33
34 /* Static rate multiplier for OMAP4 REGM4XEN clocks */
35 #define OMAP4430_REGM4XEN_MULT 4
36
omap4_dpllmx_allow_gatectrl(struct clk_hw_omap * clk)37 static void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk)
38 {
39 u32 v;
40 u32 mask;
41
42 if (!clk)
43 return;
44
45 mask = clk->flags & CLOCK_CLKOUTX2 ?
46 OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK :
47 OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK;
48
49 v = ti_clk_ll_ops->clk_readl(&clk->clksel_reg);
50 /* Clear the bit to allow gatectrl */
51 v &= ~mask;
52 ti_clk_ll_ops->clk_writel(v, &clk->clksel_reg);
53 }
54
omap4_dpllmx_deny_gatectrl(struct clk_hw_omap * clk)55 static void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk)
56 {
57 u32 v;
58 u32 mask;
59
60 if (!clk)
61 return;
62
63 mask = clk->flags & CLOCK_CLKOUTX2 ?
64 OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK :
65 OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK;
66
67 v = ti_clk_ll_ops->clk_readl(&clk->clksel_reg);
68 /* Set the bit to deny gatectrl */
69 v |= mask;
70 ti_clk_ll_ops->clk_writel(v, &clk->clksel_reg);
71 }
72
73 const struct clk_hw_omap_ops clkhwops_omap4_dpllmx = {
74 .allow_idle = omap4_dpllmx_allow_gatectrl,
75 .deny_idle = omap4_dpllmx_deny_gatectrl,
76 };
77
78 /**
79 * omap4_dpll_lpmode_recalc - compute DPLL low-power setting
80 * @dd: pointer to the dpll data structure
81 *
82 * Calculates if low-power mode can be enabled based upon the last
83 * multiplier and divider values calculated. If low-power mode can be
84 * enabled, then the bit to enable low-power mode is stored in the
85 * last_rounded_lpmode variable. This implementation is based upon the
86 * criteria for enabling low-power mode as described in the OMAP4430/60
87 * Public TRM section 3.6.3.3.2 "Enable Control, Status, and Low-Power
88 * Operation Mode".
89 */
omap4_dpll_lpmode_recalc(struct dpll_data * dd)90 static void omap4_dpll_lpmode_recalc(struct dpll_data *dd)
91 {
92 long fint, fout;
93
94 fint = clk_hw_get_rate(dd->clk_ref) / (dd->last_rounded_n + 1);
95 fout = fint * dd->last_rounded_m;
96
97 if ((fint < OMAP4_DPLL_LP_FINT_MAX) && (fout < OMAP4_DPLL_LP_FOUT_MAX))
98 dd->last_rounded_lpmode = 1;
99 else
100 dd->last_rounded_lpmode = 0;
101 }
102
103 /**
104 * omap4_dpll_regm4xen_recalc - compute DPLL rate, considering REGM4XEN bit
105 * @clk: struct clk * of the DPLL to compute the rate for
106 *
107 * Compute the output rate for the OMAP4 DPLL represented by @clk.
108 * Takes the REGM4XEN bit into consideration, which is needed for the
109 * OMAP4 ABE DPLL. Returns the DPLL's output rate (before M-dividers)
110 * upon success, or 0 upon error.
111 */
omap4_dpll_regm4xen_recalc(struct clk_hw * hw,unsigned long parent_rate)112 unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw,
113 unsigned long parent_rate)
114 {
115 struct clk_hw_omap *clk = to_clk_hw_omap(hw);
116 u32 v;
117 unsigned long rate;
118 struct dpll_data *dd;
119
120 if (!clk || !clk->dpll_data)
121 return 0;
122
123 dd = clk->dpll_data;
124
125 rate = omap2_get_dpll_rate(clk);
126
127 /* regm4xen adds a multiplier of 4 to DPLL calculations */
128 v = ti_clk_ll_ops->clk_readl(&dd->control_reg);
129 if (v & OMAP4430_DPLL_REGM4XEN_MASK)
130 rate *= OMAP4430_REGM4XEN_MULT;
131
132 return rate;
133 }
134
135 /**
136 * omap4_dpll_regm4xen_round_rate - round DPLL rate, considering REGM4XEN bit
137 * @clk: struct clk * of the DPLL to round a rate for
138 * @target_rate: the desired rate of the DPLL
139 *
140 * Compute the rate that would be programmed into the DPLL hardware
141 * for @clk if set_rate() were to be provided with the rate
142 * @target_rate. Takes the REGM4XEN bit into consideration, which is
143 * needed for the OMAP4 ABE DPLL. Returns the rounded rate (before
144 * M-dividers) upon success, -EINVAL if @clk is null or not a DPLL, or
145 * ~0 if an error occurred in omap2_dpll_round_rate().
146 */
omap4_dpll_regm4xen_round_rate(struct clk_hw * hw,unsigned long target_rate,unsigned long * parent_rate)147 long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw,
148 unsigned long target_rate,
149 unsigned long *parent_rate)
150 {
151 struct clk_hw_omap *clk = to_clk_hw_omap(hw);
152 struct dpll_data *dd;
153 long r;
154
155 if (!clk || !clk->dpll_data)
156 return -EINVAL;
157
158 dd = clk->dpll_data;
159
160 dd->last_rounded_m4xen = 0;
161
162 /*
163 * First try to compute the DPLL configuration for
164 * target rate without using the 4X multiplier.
165 */
166 r = omap2_dpll_round_rate(hw, target_rate, NULL);
167 if (r != ~0)
168 goto out;
169
170 /*
171 * If we did not find a valid DPLL configuration, try again, but
172 * this time see if using the 4X multiplier can help. Enabling the
173 * 4X multiplier is equivalent to dividing the target rate by 4.
174 */
175 r = omap2_dpll_round_rate(hw, target_rate / OMAP4430_REGM4XEN_MULT,
176 NULL);
177 if (r == ~0)
178 return r;
179
180 dd->last_rounded_rate *= OMAP4430_REGM4XEN_MULT;
181 dd->last_rounded_m4xen = 1;
182
183 out:
184 omap4_dpll_lpmode_recalc(dd);
185
186 return dd->last_rounded_rate;
187 }
188
189 /**
190 * omap4_dpll_regm4xen_determine_rate - determine rate for a DPLL
191 * @hw: pointer to the clock to determine rate for
192 * @req: target rate request
193 *
194 * Determines which DPLL mode to use for reaching a desired rate.
195 * Checks whether the DPLL shall be in bypass or locked mode, and if
196 * locked, calculates the M,N values for the DPLL via round-rate.
197 * Returns 0 on success and a negative error value otherwise.
198 */
omap4_dpll_regm4xen_determine_rate(struct clk_hw * hw,struct clk_rate_request * req)199 int omap4_dpll_regm4xen_determine_rate(struct clk_hw *hw,
200 struct clk_rate_request *req)
201 {
202 struct clk_hw_omap *clk = to_clk_hw_omap(hw);
203 struct dpll_data *dd;
204
205 if (!req->rate)
206 return -EINVAL;
207
208 dd = clk->dpll_data;
209 if (!dd)
210 return -EINVAL;
211
212 if (clk_hw_get_rate(dd->clk_bypass) == req->rate &&
213 (dd->modes & (1 << DPLL_LOW_POWER_BYPASS))) {
214 req->best_parent_hw = dd->clk_bypass;
215 } else {
216 req->rate = omap4_dpll_regm4xen_round_rate(hw, req->rate,
217 &req->best_parent_rate);
218 req->best_parent_hw = dd->clk_ref;
219 }
220
221 req->best_parent_rate = req->rate;
222
223 return 0;
224 }
225