1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Meson8, Meson8b and GXBB USB2 PHY driver
4 *
5 * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
6 */
7
8 #include <linux/clk.h>
9 #include <linux/delay.h>
10 #include <linux/io.h>
11 #include <linux/module.h>
12 #include <linux/of_device.h>
13 #include <linux/property.h>
14 #include <linux/regmap.h>
15 #include <linux/reset.h>
16 #include <linux/phy/phy.h>
17 #include <linux/platform_device.h>
18 #include <linux/usb/of.h>
19
20 #define REG_CONFIG 0x00
21 #define REG_CONFIG_CLK_EN BIT(0)
22 #define REG_CONFIG_CLK_SEL_MASK GENMASK(3, 1)
23 #define REG_CONFIG_CLK_DIV_MASK GENMASK(10, 4)
24 #define REG_CONFIG_CLK_32k_ALTSEL BIT(15)
25 #define REG_CONFIG_TEST_TRIG BIT(31)
26
27 #define REG_CTRL 0x04
28 #define REG_CTRL_SOFT_PRST BIT(0)
29 #define REG_CTRL_SOFT_HRESET BIT(1)
30 #define REG_CTRL_SS_SCALEDOWN_MODE_MASK GENMASK(3, 2)
31 #define REG_CTRL_CLK_DET_RST BIT(4)
32 #define REG_CTRL_INTR_SEL BIT(5)
33 #define REG_CTRL_CLK_DETECTED BIT(8)
34 #define REG_CTRL_SOF_SENT_RCVD_TGL BIT(9)
35 #define REG_CTRL_SOF_TOGGLE_OUT BIT(10)
36 #define REG_CTRL_POWER_ON_RESET BIT(15)
37 #define REG_CTRL_SLEEPM BIT(16)
38 #define REG_CTRL_TX_BITSTUFF_ENN_H BIT(17)
39 #define REG_CTRL_TX_BITSTUFF_ENN BIT(18)
40 #define REG_CTRL_COMMON_ON BIT(19)
41 #define REG_CTRL_REF_CLK_SEL_MASK GENMASK(21, 20)
42 #define REG_CTRL_REF_CLK_SEL_SHIFT 20
43 #define REG_CTRL_FSEL_MASK GENMASK(24, 22)
44 #define REG_CTRL_FSEL_SHIFT 22
45 #define REG_CTRL_PORT_RESET BIT(25)
46 #define REG_CTRL_THREAD_ID_MASK GENMASK(31, 26)
47
48 #define REG_ENDP_INTR 0x08
49
50 /* bits [31:26], [24:21] and [15:3] seem to be read-only */
51 #define REG_ADP_BC 0x0c
52 #define REG_ADP_BC_VBUS_VLD_EXT_SEL BIT(0)
53 #define REG_ADP_BC_VBUS_VLD_EXT BIT(1)
54 #define REG_ADP_BC_OTG_DISABLE BIT(2)
55 #define REG_ADP_BC_ID_PULLUP BIT(3)
56 #define REG_ADP_BC_DRV_VBUS BIT(4)
57 #define REG_ADP_BC_ADP_PRB_EN BIT(5)
58 #define REG_ADP_BC_ADP_DISCHARGE BIT(6)
59 #define REG_ADP_BC_ADP_CHARGE BIT(7)
60 #define REG_ADP_BC_SESS_END BIT(8)
61 #define REG_ADP_BC_DEVICE_SESS_VLD BIT(9)
62 #define REG_ADP_BC_B_VALID BIT(10)
63 #define REG_ADP_BC_A_VALID BIT(11)
64 #define REG_ADP_BC_ID_DIG BIT(12)
65 #define REG_ADP_BC_VBUS_VALID BIT(13)
66 #define REG_ADP_BC_ADP_PROBE BIT(14)
67 #define REG_ADP_BC_ADP_SENSE BIT(15)
68 #define REG_ADP_BC_ACA_ENABLE BIT(16)
69 #define REG_ADP_BC_DCD_ENABLE BIT(17)
70 #define REG_ADP_BC_VDAT_DET_EN_B BIT(18)
71 #define REG_ADP_BC_VDAT_SRC_EN_B BIT(19)
72 #define REG_ADP_BC_CHARGE_SEL BIT(20)
73 #define REG_ADP_BC_CHARGE_DETECT BIT(21)
74 #define REG_ADP_BC_ACA_PIN_RANGE_C BIT(22)
75 #define REG_ADP_BC_ACA_PIN_RANGE_B BIT(23)
76 #define REG_ADP_BC_ACA_PIN_RANGE_A BIT(24)
77 #define REG_ADP_BC_ACA_PIN_GND BIT(25)
78 #define REG_ADP_BC_ACA_PIN_FLOAT BIT(26)
79
80 #define REG_DBG_UART 0x10
81 #define REG_DBG_UART_BYPASS_SEL BIT(0)
82 #define REG_DBG_UART_BYPASS_DM_EN BIT(1)
83 #define REG_DBG_UART_BYPASS_DP_EN BIT(2)
84 #define REG_DBG_UART_BYPASS_DM_DATA BIT(3)
85 #define REG_DBG_UART_BYPASS_DP_DATA BIT(4)
86 #define REG_DBG_UART_FSV_MINUS BIT(5)
87 #define REG_DBG_UART_FSV_PLUS BIT(6)
88 #define REG_DBG_UART_FSV_BURN_IN_TEST BIT(7)
89 #define REG_DBG_UART_LOOPBACK_EN_B BIT(8)
90 #define REG_DBG_UART_SET_IDDQ BIT(9)
91 #define REG_DBG_UART_ATE_RESET BIT(10)
92
93 #define REG_TEST 0x14
94 #define REG_TEST_DATA_IN_MASK GENMASK(3, 0)
95 #define REG_TEST_EN_MASK GENMASK(7, 4)
96 #define REG_TEST_ADDR_MASK GENMASK(11, 8)
97 #define REG_TEST_DATA_OUT_SEL BIT(12)
98 #define REG_TEST_CLK BIT(13)
99 #define REG_TEST_VA_TEST_EN_B_MASK GENMASK(15, 14)
100 #define REG_TEST_DATA_OUT_MASK GENMASK(19, 16)
101 #define REG_TEST_DISABLE_ID_PULLUP BIT(20)
102
103 #define REG_TUNE 0x18
104 #define REG_TUNE_TX_RES_TUNE_MASK GENMASK(1, 0)
105 #define REG_TUNE_TX_HSXV_TUNE_MASK GENMASK(3, 2)
106 #define REG_TUNE_TX_VREF_TUNE_MASK GENMASK(7, 4)
107 #define REG_TUNE_TX_RISE_TUNE_MASK GENMASK(9, 8)
108 #define REG_TUNE_TX_PREEMP_PULSE_TUNE BIT(10)
109 #define REG_TUNE_TX_PREEMP_AMP_TUNE_MASK GENMASK(12, 11)
110 #define REG_TUNE_TX_FSLS_TUNE_MASK GENMASK(16, 13)
111 #define REG_TUNE_SQRX_TUNE_MASK GENMASK(19, 17)
112 #define REG_TUNE_OTG_TUNE GENMASK(22, 20)
113 #define REG_TUNE_COMP_DIS_TUNE GENMASK(25, 23)
114 #define REG_TUNE_HOST_DM_PULLDOWN BIT(26)
115 #define REG_TUNE_HOST_DP_PULLDOWN BIT(27)
116
117 #define RESET_COMPLETE_TIME 500
118 #define ACA_ENABLE_COMPLETE_TIME 50
119
120 struct phy_meson8b_usb2_match_data {
121 bool host_enable_aca;
122 };
123
124 struct phy_meson8b_usb2_priv {
125 struct regmap *regmap;
126 enum usb_dr_mode dr_mode;
127 struct clk *clk_usb_general;
128 struct clk *clk_usb;
129 struct reset_control *reset;
130 const struct phy_meson8b_usb2_match_data *match;
131 };
132
133 static const struct regmap_config phy_meson8b_usb2_regmap_conf = {
134 .reg_bits = 8,
135 .val_bits = 32,
136 .reg_stride = 4,
137 .max_register = REG_TUNE,
138 };
139
phy_meson8b_usb2_power_on(struct phy * phy)140 static int phy_meson8b_usb2_power_on(struct phy *phy)
141 {
142 struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy);
143 u32 reg;
144 int ret;
145
146 if (!IS_ERR_OR_NULL(priv->reset)) {
147 ret = reset_control_reset(priv->reset);
148 if (ret) {
149 dev_err(&phy->dev, "Failed to trigger USB reset\n");
150 return ret;
151 }
152 }
153
154 ret = clk_prepare_enable(priv->clk_usb_general);
155 if (ret) {
156 dev_err(&phy->dev, "Failed to enable USB general clock\n");
157 return ret;
158 }
159
160 ret = clk_prepare_enable(priv->clk_usb);
161 if (ret) {
162 dev_err(&phy->dev, "Failed to enable USB DDR clock\n");
163 clk_disable_unprepare(priv->clk_usb_general);
164 return ret;
165 }
166
167 regmap_update_bits(priv->regmap, REG_CONFIG, REG_CONFIG_CLK_32k_ALTSEL,
168 REG_CONFIG_CLK_32k_ALTSEL);
169
170 regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_REF_CLK_SEL_MASK,
171 0x2 << REG_CTRL_REF_CLK_SEL_SHIFT);
172
173 regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_FSEL_MASK,
174 0x5 << REG_CTRL_FSEL_SHIFT);
175
176 /* reset the PHY */
177 regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_POWER_ON_RESET,
178 REG_CTRL_POWER_ON_RESET);
179 udelay(RESET_COMPLETE_TIME);
180 regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_POWER_ON_RESET, 0);
181 udelay(RESET_COMPLETE_TIME);
182
183 regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT,
184 REG_CTRL_SOF_TOGGLE_OUT);
185
186 if (priv->dr_mode == USB_DR_MODE_HOST) {
187 regmap_update_bits(priv->regmap, REG_DBG_UART,
188 REG_DBG_UART_SET_IDDQ, 0);
189
190 if (priv->match->host_enable_aca) {
191 regmap_update_bits(priv->regmap, REG_ADP_BC,
192 REG_ADP_BC_ACA_ENABLE,
193 REG_ADP_BC_ACA_ENABLE);
194
195 udelay(ACA_ENABLE_COMPLETE_TIME);
196
197 regmap_read(priv->regmap, REG_ADP_BC, ®);
198 if (reg & REG_ADP_BC_ACA_PIN_FLOAT) {
199 dev_warn(&phy->dev, "USB ID detect failed!\n");
200 clk_disable_unprepare(priv->clk_usb);
201 clk_disable_unprepare(priv->clk_usb_general);
202 return -EINVAL;
203 }
204 }
205 }
206
207 return 0;
208 }
209
phy_meson8b_usb2_power_off(struct phy * phy)210 static int phy_meson8b_usb2_power_off(struct phy *phy)
211 {
212 struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy);
213
214 if (priv->dr_mode == USB_DR_MODE_HOST)
215 regmap_update_bits(priv->regmap, REG_DBG_UART,
216 REG_DBG_UART_SET_IDDQ,
217 REG_DBG_UART_SET_IDDQ);
218
219 clk_disable_unprepare(priv->clk_usb);
220 clk_disable_unprepare(priv->clk_usb_general);
221
222 return 0;
223 }
224
225 static const struct phy_ops phy_meson8b_usb2_ops = {
226 .power_on = phy_meson8b_usb2_power_on,
227 .power_off = phy_meson8b_usb2_power_off,
228 .owner = THIS_MODULE,
229 };
230
phy_meson8b_usb2_probe(struct platform_device * pdev)231 static int phy_meson8b_usb2_probe(struct platform_device *pdev)
232 {
233 struct phy_meson8b_usb2_priv *priv;
234 struct phy *phy;
235 struct phy_provider *phy_provider;
236 void __iomem *base;
237
238 priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
239 if (!priv)
240 return -ENOMEM;
241
242 base = devm_platform_ioremap_resource(pdev, 0);
243 if (IS_ERR(base))
244 return PTR_ERR(base);
245
246 priv->match = device_get_match_data(&pdev->dev);
247 if (!priv->match)
248 return -ENODEV;
249
250 priv->regmap = devm_regmap_init_mmio(&pdev->dev, base,
251 &phy_meson8b_usb2_regmap_conf);
252 if (IS_ERR(priv->regmap))
253 return PTR_ERR(priv->regmap);
254
255 priv->clk_usb_general = devm_clk_get(&pdev->dev, "usb_general");
256 if (IS_ERR(priv->clk_usb_general))
257 return PTR_ERR(priv->clk_usb_general);
258
259 priv->clk_usb = devm_clk_get(&pdev->dev, "usb");
260 if (IS_ERR(priv->clk_usb))
261 return PTR_ERR(priv->clk_usb);
262
263 priv->reset = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
264 if (IS_ERR(priv->reset))
265 return dev_err_probe(&pdev->dev, PTR_ERR(priv->reset),
266 "Failed to get the reset line");
267
268 priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1);
269 if (priv->dr_mode == USB_DR_MODE_UNKNOWN) {
270 dev_err(&pdev->dev,
271 "missing dual role configuration of the controller\n");
272 return -EINVAL;
273 }
274
275 phy = devm_phy_create(&pdev->dev, NULL, &phy_meson8b_usb2_ops);
276 if (IS_ERR(phy)) {
277 dev_err(&pdev->dev, "failed to create PHY\n");
278 return PTR_ERR(phy);
279 }
280
281 phy_set_drvdata(phy, priv);
282
283 phy_provider =
284 devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
285
286 return PTR_ERR_OR_ZERO(phy_provider);
287 }
288
289 static const struct phy_meson8b_usb2_match_data phy_meson8_usb2_match_data = {
290 .host_enable_aca = false,
291 };
292
293 static const struct phy_meson8b_usb2_match_data phy_meson8b_usb2_match_data = {
294 .host_enable_aca = true,
295 };
296
297 static const struct of_device_id phy_meson8b_usb2_of_match[] = {
298 {
299 .compatible = "amlogic,meson8-usb2-phy",
300 .data = &phy_meson8_usb2_match_data
301 },
302 {
303 .compatible = "amlogic,meson8b-usb2-phy",
304 .data = &phy_meson8b_usb2_match_data
305 },
306 {
307 .compatible = "amlogic,meson8m2-usb2-phy",
308 .data = &phy_meson8b_usb2_match_data
309 },
310 {
311 .compatible = "amlogic,meson-gxbb-usb2-phy",
312 .data = &phy_meson8b_usb2_match_data
313 },
314 { /* sentinel */ }
315 };
316 MODULE_DEVICE_TABLE(of, phy_meson8b_usb2_of_match);
317
318 static struct platform_driver phy_meson8b_usb2_driver = {
319 .probe = phy_meson8b_usb2_probe,
320 .driver = {
321 .name = "phy-meson-usb2",
322 .of_match_table = phy_meson8b_usb2_of_match,
323 },
324 };
325 module_platform_driver(phy_meson8b_usb2_driver);
326
327 MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
328 MODULE_DESCRIPTION("Meson8, Meson8b, Meson8m2 and GXBB USB2 PHY driver");
329 MODULE_LICENSE("GPL");
330