1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * (C) Copyright 2008
4 * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
5 *
6 * This driver implements a lcd device for the ILITEK 922x display
7 * controller. The interface to the display is SPI and the display's
8 * memory is cyclically updated over the RGB interface.
9 */
10
11 #include <linux/fb.h>
12 #include <linux/delay.h>
13 #include <linux/errno.h>
14 #include <linux/init.h>
15 #include <linux/kernel.h>
16 #include <linux/lcd.h>
17 #include <linux/module.h>
18 #include <linux/of.h>
19 #include <linux/slab.h>
20 #include <linux/spi/spi.h>
21 #include <linux/string.h>
22
23 /* Register offset, see manual section 8.2 */
24 #define REG_START_OSCILLATION 0x00
25 #define REG_DRIVER_CODE_READ 0x00
26 #define REG_DRIVER_OUTPUT_CONTROL 0x01
27 #define REG_LCD_AC_DRIVEING_CONTROL 0x02
28 #define REG_ENTRY_MODE 0x03
29 #define REG_COMPARE_1 0x04
30 #define REG_COMPARE_2 0x05
31 #define REG_DISPLAY_CONTROL_1 0x07
32 #define REG_DISPLAY_CONTROL_2 0x08
33 #define REG_DISPLAY_CONTROL_3 0x09
34 #define REG_FRAME_CYCLE_CONTROL 0x0B
35 #define REG_EXT_INTF_CONTROL 0x0C
36 #define REG_POWER_CONTROL_1 0x10
37 #define REG_POWER_CONTROL_2 0x11
38 #define REG_POWER_CONTROL_3 0x12
39 #define REG_POWER_CONTROL_4 0x13
40 #define REG_RAM_ADDRESS_SET 0x21
41 #define REG_WRITE_DATA_TO_GRAM 0x22
42 #define REG_RAM_WRITE_MASK1 0x23
43 #define REG_RAM_WRITE_MASK2 0x24
44 #define REG_GAMMA_CONTROL_1 0x30
45 #define REG_GAMMA_CONTROL_2 0x31
46 #define REG_GAMMA_CONTROL_3 0x32
47 #define REG_GAMMA_CONTROL_4 0x33
48 #define REG_GAMMA_CONTROL_5 0x34
49 #define REG_GAMMA_CONTROL_6 0x35
50 #define REG_GAMMA_CONTROL_7 0x36
51 #define REG_GAMMA_CONTROL_8 0x37
52 #define REG_GAMMA_CONTROL_9 0x38
53 #define REG_GAMMA_CONTROL_10 0x39
54 #define REG_GATE_SCAN_CONTROL 0x40
55 #define REG_VERT_SCROLL_CONTROL 0x41
56 #define REG_FIRST_SCREEN_DRIVE_POS 0x42
57 #define REG_SECOND_SCREEN_DRIVE_POS 0x43
58 #define REG_RAM_ADDR_POS_H 0x44
59 #define REG_RAM_ADDR_POS_V 0x45
60 #define REG_OSCILLATOR_CONTROL 0x4F
61 #define REG_GPIO 0x60
62 #define REG_OTP_VCM_PROGRAMMING 0x61
63 #define REG_OTP_VCM_STATUS_ENABLE 0x62
64 #define REG_OTP_PROGRAMMING_ID_KEY 0x65
65
66 /*
67 * maximum frequency for register access
68 * (not for the GRAM access)
69 */
70 #define ILITEK_MAX_FREQ_REG 4000000
71
72 /*
73 * Device ID as found in the datasheet (supports 9221 and 9222)
74 */
75 #define ILITEK_DEVICE_ID 0x9220
76 #define ILITEK_DEVICE_ID_MASK 0xFFF0
77
78 /* Last two bits in the START BYTE */
79 #define START_RS_INDEX 0
80 #define START_RS_REG 1
81 #define START_RW_WRITE 0
82 #define START_RW_READ 1
83
84 /**
85 * START_BYTE(id, rs, rw)
86 *
87 * Set the start byte according to the required operation.
88 * The start byte is defined as:
89 * ----------------------------------
90 * | 0 | 1 | 1 | 1 | 0 | ID | RS | RW |
91 * ----------------------------------
92 * @id: display's id as set by the manufacturer
93 * @rs: operation type bit, one of:
94 * - START_RS_INDEX set the index register
95 * - START_RS_REG write/read registers/GRAM
96 * @rw: read/write operation
97 * - START_RW_WRITE write
98 * - START_RW_READ read
99 */
100 #define START_BYTE(id, rs, rw) \
101 (0x70 | (((id) & 0x01) << 2) | (((rs) & 0x01) << 1) | ((rw) & 0x01))
102
103 /**
104 * CHECK_FREQ_REG(spi_device s, spi_transfer x) - Check the frequency
105 * for the SPI transfer. According to the datasheet, the controller
106 * accept higher frequency for the GRAM transfer, but it requires
107 * lower frequency when the registers are read/written.
108 * The macro sets the frequency in the spi_transfer structure if
109 * the frequency exceeds the maximum value.
110 * @s: pointer to an SPI device
111 * @x: pointer to the read/write buffer pair
112 */
113 #define CHECK_FREQ_REG(s, x) \
114 do { \
115 if (s->max_speed_hz > ILITEK_MAX_FREQ_REG) \
116 ((struct spi_transfer *)x)->speed_hz = \
117 ILITEK_MAX_FREQ_REG; \
118 } while (0)
119
120 #define CMD_BUFSIZE 16
121
122 #define POWER_IS_ON(pwr) ((pwr) <= FB_BLANK_NORMAL)
123
124 #define set_tx_byte(b) (tx_invert ? ~(b) : b)
125
126 /*
127 * ili922x_id - id as set by manufacturer
128 */
129 static int ili922x_id = 1;
130 module_param(ili922x_id, int, 0);
131
132 static int tx_invert;
133 module_param(tx_invert, int, 0);
134
135 /*
136 * driver's private structure
137 */
138 struct ili922x {
139 struct spi_device *spi;
140 struct lcd_device *ld;
141 int power;
142 };
143
144 /**
145 * ili922x_read_status - read status register from display
146 * @spi: spi device
147 * @rs: output value
148 */
ili922x_read_status(struct spi_device * spi,u16 * rs)149 static int ili922x_read_status(struct spi_device *spi, u16 *rs)
150 {
151 struct spi_message msg;
152 struct spi_transfer xfer;
153 unsigned char tbuf[CMD_BUFSIZE];
154 unsigned char rbuf[CMD_BUFSIZE];
155 int ret, i;
156
157 memset(&xfer, 0, sizeof(struct spi_transfer));
158 spi_message_init(&msg);
159 xfer.tx_buf = tbuf;
160 xfer.rx_buf = rbuf;
161 xfer.cs_change = 1;
162 CHECK_FREQ_REG(spi, &xfer);
163
164 tbuf[0] = set_tx_byte(START_BYTE(ili922x_id, START_RS_INDEX,
165 START_RW_READ));
166 /*
167 * we need 4-byte xfer here due to invalid dummy byte
168 * received after start byte
169 */
170 for (i = 1; i < 4; i++)
171 tbuf[i] = set_tx_byte(0); /* dummy */
172
173 xfer.bits_per_word = 8;
174 xfer.len = 4;
175 spi_message_add_tail(&xfer, &msg);
176 ret = spi_sync(spi, &msg);
177 if (ret < 0) {
178 dev_dbg(&spi->dev, "Error sending SPI message 0x%x", ret);
179 return ret;
180 }
181
182 *rs = (rbuf[2] << 8) + rbuf[3];
183 return 0;
184 }
185
186 /**
187 * ili922x_read - read register from display
188 * @spi: spi device
189 * @reg: offset of the register to be read
190 * @rx: output value
191 */
ili922x_read(struct spi_device * spi,u8 reg,u16 * rx)192 static int ili922x_read(struct spi_device *spi, u8 reg, u16 *rx)
193 {
194 struct spi_message msg;
195 struct spi_transfer xfer_regindex, xfer_regvalue;
196 unsigned char tbuf[CMD_BUFSIZE];
197 unsigned char rbuf[CMD_BUFSIZE];
198 int ret, len = 0, send_bytes;
199
200 memset(&xfer_regindex, 0, sizeof(struct spi_transfer));
201 memset(&xfer_regvalue, 0, sizeof(struct spi_transfer));
202 spi_message_init(&msg);
203 xfer_regindex.tx_buf = tbuf;
204 xfer_regindex.rx_buf = rbuf;
205 xfer_regindex.cs_change = 1;
206 CHECK_FREQ_REG(spi, &xfer_regindex);
207
208 tbuf[0] = set_tx_byte(START_BYTE(ili922x_id, START_RS_INDEX,
209 START_RW_WRITE));
210 tbuf[1] = set_tx_byte(0);
211 tbuf[2] = set_tx_byte(reg);
212 xfer_regindex.bits_per_word = 8;
213 len = xfer_regindex.len = 3;
214 spi_message_add_tail(&xfer_regindex, &msg);
215
216 send_bytes = len;
217
218 tbuf[len++] = set_tx_byte(START_BYTE(ili922x_id, START_RS_REG,
219 START_RW_READ));
220 tbuf[len++] = set_tx_byte(0);
221 tbuf[len] = set_tx_byte(0);
222
223 xfer_regvalue.cs_change = 1;
224 xfer_regvalue.len = 3;
225 xfer_regvalue.tx_buf = &tbuf[send_bytes];
226 xfer_regvalue.rx_buf = &rbuf[send_bytes];
227 CHECK_FREQ_REG(spi, &xfer_regvalue);
228
229 spi_message_add_tail(&xfer_regvalue, &msg);
230 ret = spi_sync(spi, &msg);
231 if (ret < 0) {
232 dev_dbg(&spi->dev, "Error sending SPI message 0x%x", ret);
233 return ret;
234 }
235
236 *rx = (rbuf[1 + send_bytes] << 8) + rbuf[2 + send_bytes];
237 return 0;
238 }
239
240 /**
241 * ili922x_write - write a controller register
242 * @spi: struct spi_device *
243 * @reg: offset of the register to be written
244 * @value: value to be written
245 */
ili922x_write(struct spi_device * spi,u8 reg,u16 value)246 static int ili922x_write(struct spi_device *spi, u8 reg, u16 value)
247 {
248 struct spi_message msg;
249 struct spi_transfer xfer_regindex, xfer_regvalue;
250 unsigned char tbuf[CMD_BUFSIZE];
251 unsigned char rbuf[CMD_BUFSIZE];
252 int ret;
253
254 memset(&xfer_regindex, 0, sizeof(struct spi_transfer));
255 memset(&xfer_regvalue, 0, sizeof(struct spi_transfer));
256
257 spi_message_init(&msg);
258 xfer_regindex.tx_buf = tbuf;
259 xfer_regindex.rx_buf = rbuf;
260 xfer_regindex.cs_change = 1;
261 CHECK_FREQ_REG(spi, &xfer_regindex);
262
263 tbuf[0] = set_tx_byte(START_BYTE(ili922x_id, START_RS_INDEX,
264 START_RW_WRITE));
265 tbuf[1] = set_tx_byte(0);
266 tbuf[2] = set_tx_byte(reg);
267 xfer_regindex.bits_per_word = 8;
268 xfer_regindex.len = 3;
269 spi_message_add_tail(&xfer_regindex, &msg);
270
271 ret = spi_sync(spi, &msg);
272
273 spi_message_init(&msg);
274 tbuf[0] = set_tx_byte(START_BYTE(ili922x_id, START_RS_REG,
275 START_RW_WRITE));
276 tbuf[1] = set_tx_byte((value & 0xFF00) >> 8);
277 tbuf[2] = set_tx_byte(value & 0x00FF);
278
279 xfer_regvalue.cs_change = 1;
280 xfer_regvalue.len = 3;
281 xfer_regvalue.tx_buf = tbuf;
282 xfer_regvalue.rx_buf = rbuf;
283 CHECK_FREQ_REG(spi, &xfer_regvalue);
284
285 spi_message_add_tail(&xfer_regvalue, &msg);
286
287 ret = spi_sync(spi, &msg);
288 if (ret < 0) {
289 dev_err(&spi->dev, "Error sending SPI message 0x%x", ret);
290 return ret;
291 }
292 return 0;
293 }
294
295 #ifdef DEBUG
296 /**
297 * ili922x_reg_dump - dump all registers
298 *
299 * @spi: pointer to an SPI device
300 */
ili922x_reg_dump(struct spi_device * spi)301 static void ili922x_reg_dump(struct spi_device *spi)
302 {
303 u8 reg;
304 u16 rx;
305
306 dev_dbg(&spi->dev, "ILI922x configuration registers:\n");
307 for (reg = REG_START_OSCILLATION;
308 reg <= REG_OTP_PROGRAMMING_ID_KEY; reg++) {
309 ili922x_read(spi, reg, &rx);
310 dev_dbg(&spi->dev, "reg @ 0x%02X: 0x%04X\n", reg, rx);
311 }
312 }
313 #else
ili922x_reg_dump(struct spi_device * spi)314 static inline void ili922x_reg_dump(struct spi_device *spi) {}
315 #endif
316
317 /**
318 * set_write_to_gram_reg - initialize the display to write the GRAM
319 * @spi: spi device
320 */
set_write_to_gram_reg(struct spi_device * spi)321 static void set_write_to_gram_reg(struct spi_device *spi)
322 {
323 struct spi_message msg;
324 struct spi_transfer xfer;
325 unsigned char tbuf[CMD_BUFSIZE];
326
327 memset(&xfer, 0, sizeof(struct spi_transfer));
328
329 spi_message_init(&msg);
330 xfer.tx_buf = tbuf;
331 xfer.rx_buf = NULL;
332 xfer.cs_change = 1;
333
334 tbuf[0] = START_BYTE(ili922x_id, START_RS_INDEX, START_RW_WRITE);
335 tbuf[1] = 0;
336 tbuf[2] = REG_WRITE_DATA_TO_GRAM;
337
338 xfer.bits_per_word = 8;
339 xfer.len = 3;
340 spi_message_add_tail(&xfer, &msg);
341 spi_sync(spi, &msg);
342 }
343
344 /**
345 * ili922x_poweron - turn the display on
346 * @spi: spi device
347 *
348 * The sequence to turn on the display is taken from
349 * the datasheet and/or the example code provided by the
350 * manufacturer.
351 */
ili922x_poweron(struct spi_device * spi)352 static int ili922x_poweron(struct spi_device *spi)
353 {
354 int ret;
355
356 /* Power on */
357 ret = ili922x_write(spi, REG_POWER_CONTROL_1, 0x0000);
358 usleep_range(10000, 10500);
359 ret += ili922x_write(spi, REG_POWER_CONTROL_2, 0x0000);
360 ret += ili922x_write(spi, REG_POWER_CONTROL_3, 0x0000);
361 msleep(40);
362 ret += ili922x_write(spi, REG_POWER_CONTROL_4, 0x0000);
363 msleep(40);
364 /* register 0x56 is not documented in the datasheet */
365 ret += ili922x_write(spi, 0x56, 0x080F);
366 ret += ili922x_write(spi, REG_POWER_CONTROL_1, 0x4240);
367 usleep_range(10000, 10500);
368 ret += ili922x_write(spi, REG_POWER_CONTROL_2, 0x0000);
369 ret += ili922x_write(spi, REG_POWER_CONTROL_3, 0x0014);
370 msleep(40);
371 ret += ili922x_write(spi, REG_POWER_CONTROL_4, 0x1319);
372 msleep(40);
373
374 return ret;
375 }
376
377 /**
378 * ili922x_poweroff - turn the display off
379 * @spi: spi device
380 */
ili922x_poweroff(struct spi_device * spi)381 static int ili922x_poweroff(struct spi_device *spi)
382 {
383 int ret;
384
385 /* Power off */
386 ret = ili922x_write(spi, REG_POWER_CONTROL_1, 0x0000);
387 usleep_range(10000, 10500);
388 ret += ili922x_write(spi, REG_POWER_CONTROL_2, 0x0000);
389 ret += ili922x_write(spi, REG_POWER_CONTROL_3, 0x0000);
390 msleep(40);
391 ret += ili922x_write(spi, REG_POWER_CONTROL_4, 0x0000);
392 msleep(40);
393
394 return ret;
395 }
396
397 /**
398 * ili922x_display_init - initialize the display by setting
399 * the configuration registers
400 * @spi: spi device
401 */
ili922x_display_init(struct spi_device * spi)402 static void ili922x_display_init(struct spi_device *spi)
403 {
404 ili922x_write(spi, REG_START_OSCILLATION, 1);
405 usleep_range(10000, 10500);
406 ili922x_write(spi, REG_DRIVER_OUTPUT_CONTROL, 0x691B);
407 ili922x_write(spi, REG_LCD_AC_DRIVEING_CONTROL, 0x0700);
408 ili922x_write(spi, REG_ENTRY_MODE, 0x1030);
409 ili922x_write(spi, REG_COMPARE_1, 0x0000);
410 ili922x_write(spi, REG_COMPARE_2, 0x0000);
411 ili922x_write(spi, REG_DISPLAY_CONTROL_1, 0x0037);
412 ili922x_write(spi, REG_DISPLAY_CONTROL_2, 0x0202);
413 ili922x_write(spi, REG_DISPLAY_CONTROL_3, 0x0000);
414 ili922x_write(spi, REG_FRAME_CYCLE_CONTROL, 0x0000);
415
416 /* Set RGB interface */
417 ili922x_write(spi, REG_EXT_INTF_CONTROL, 0x0110);
418
419 ili922x_poweron(spi);
420
421 ili922x_write(spi, REG_GAMMA_CONTROL_1, 0x0302);
422 ili922x_write(spi, REG_GAMMA_CONTROL_2, 0x0407);
423 ili922x_write(spi, REG_GAMMA_CONTROL_3, 0x0304);
424 ili922x_write(spi, REG_GAMMA_CONTROL_4, 0x0203);
425 ili922x_write(spi, REG_GAMMA_CONTROL_5, 0x0706);
426 ili922x_write(spi, REG_GAMMA_CONTROL_6, 0x0407);
427 ili922x_write(spi, REG_GAMMA_CONTROL_7, 0x0706);
428 ili922x_write(spi, REG_GAMMA_CONTROL_8, 0x0000);
429 ili922x_write(spi, REG_GAMMA_CONTROL_9, 0x0C06);
430 ili922x_write(spi, REG_GAMMA_CONTROL_10, 0x0F00);
431 ili922x_write(spi, REG_RAM_ADDRESS_SET, 0x0000);
432 ili922x_write(spi, REG_GATE_SCAN_CONTROL, 0x0000);
433 ili922x_write(spi, REG_VERT_SCROLL_CONTROL, 0x0000);
434 ili922x_write(spi, REG_FIRST_SCREEN_DRIVE_POS, 0xDB00);
435 ili922x_write(spi, REG_SECOND_SCREEN_DRIVE_POS, 0xDB00);
436 ili922x_write(spi, REG_RAM_ADDR_POS_H, 0xAF00);
437 ili922x_write(spi, REG_RAM_ADDR_POS_V, 0xDB00);
438 ili922x_reg_dump(spi);
439 set_write_to_gram_reg(spi);
440 }
441
ili922x_lcd_power(struct ili922x * lcd,int power)442 static int ili922x_lcd_power(struct ili922x *lcd, int power)
443 {
444 int ret = 0;
445
446 if (POWER_IS_ON(power) && !POWER_IS_ON(lcd->power))
447 ret = ili922x_poweron(lcd->spi);
448 else if (!POWER_IS_ON(power) && POWER_IS_ON(lcd->power))
449 ret = ili922x_poweroff(lcd->spi);
450
451 if (!ret)
452 lcd->power = power;
453
454 return ret;
455 }
456
ili922x_set_power(struct lcd_device * ld,int power)457 static int ili922x_set_power(struct lcd_device *ld, int power)
458 {
459 struct ili922x *ili = lcd_get_data(ld);
460
461 return ili922x_lcd_power(ili, power);
462 }
463
ili922x_get_power(struct lcd_device * ld)464 static int ili922x_get_power(struct lcd_device *ld)
465 {
466 struct ili922x *ili = lcd_get_data(ld);
467
468 return ili->power;
469 }
470
471 static struct lcd_ops ili922x_ops = {
472 .get_power = ili922x_get_power,
473 .set_power = ili922x_set_power,
474 };
475
ili922x_probe(struct spi_device * spi)476 static int ili922x_probe(struct spi_device *spi)
477 {
478 struct ili922x *ili;
479 struct lcd_device *lcd;
480 int ret;
481 u16 reg = 0;
482
483 ili = devm_kzalloc(&spi->dev, sizeof(*ili), GFP_KERNEL);
484 if (!ili)
485 return -ENOMEM;
486
487 ili->spi = spi;
488 spi_set_drvdata(spi, ili);
489
490 /* check if the device is connected */
491 ret = ili922x_read(spi, REG_DRIVER_CODE_READ, ®);
492 if (ret || ((reg & ILITEK_DEVICE_ID_MASK) != ILITEK_DEVICE_ID)) {
493 dev_err(&spi->dev,
494 "no LCD found: Chip ID 0x%x, ret %d\n",
495 reg, ret);
496 return -ENODEV;
497 }
498
499 dev_info(&spi->dev, "ILI%x found, SPI freq %d, mode %d\n",
500 reg, spi->max_speed_hz, spi->mode);
501
502 ret = ili922x_read_status(spi, ®);
503 if (ret) {
504 dev_err(&spi->dev, "reading RS failed...\n");
505 return ret;
506 }
507
508 dev_dbg(&spi->dev, "status: 0x%x\n", reg);
509
510 ili922x_display_init(spi);
511
512 ili->power = FB_BLANK_POWERDOWN;
513
514 lcd = devm_lcd_device_register(&spi->dev, "ili922xlcd", &spi->dev, ili,
515 &ili922x_ops);
516 if (IS_ERR(lcd)) {
517 dev_err(&spi->dev, "cannot register LCD\n");
518 return PTR_ERR(lcd);
519 }
520
521 ili->ld = lcd;
522 spi_set_drvdata(spi, ili);
523
524 ili922x_lcd_power(ili, FB_BLANK_UNBLANK);
525
526 return 0;
527 }
528
ili922x_remove(struct spi_device * spi)529 static int ili922x_remove(struct spi_device *spi)
530 {
531 ili922x_poweroff(spi);
532 return 0;
533 }
534
535 static struct spi_driver ili922x_driver = {
536 .driver = {
537 .name = "ili922x",
538 },
539 .probe = ili922x_probe,
540 .remove = ili922x_remove,
541 };
542
543 module_spi_driver(ili922x_driver);
544
545 MODULE_AUTHOR("Stefano Babic <sbabic@denx.de>");
546 MODULE_DESCRIPTION("ILI9221/9222 LCD driver");
547 MODULE_LICENSE("GPL");
548 MODULE_PARM_DESC(ili922x_id, "set controller identifier (default=1)");
549 MODULE_PARM_DESC(tx_invert, "invert bytes before sending");
550