1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Mediatek 8250 driver.
4 *
5 * Copyright (c) 2014 MundoReader S.L.
6 * Author: Matthias Brugger <matthias.bgg@gmail.com>
7 */
8 #include <linux/clk.h>
9 #include <linux/io.h>
10 #include <linux/module.h>
11 #include <linux/of_irq.h>
12 #include <linux/of_platform.h>
13 #include <linux/pinctrl/consumer.h>
14 #include <linux/platform_device.h>
15 #include <linux/pm_runtime.h>
16 #include <linux/serial_8250.h>
17 #include <linux/serial_reg.h>
18 #include <linux/console.h>
19 #include <linux/dma-mapping.h>
20 #include <linux/tty.h>
21 #include <linux/tty_flip.h>
22
23 #include "8250.h"
24
25 #define MTK_UART_HIGHS 0x09 /* Highspeed register */
26 #define MTK_UART_SAMPLE_COUNT 0x0a /* Sample count register */
27 #define MTK_UART_SAMPLE_POINT 0x0b /* Sample point register */
28 #define MTK_UART_RATE_FIX 0x0d /* UART Rate Fix Register */
29 #define MTK_UART_ESCAPE_DAT 0x10 /* Escape Character register */
30 #define MTK_UART_ESCAPE_EN 0x11 /* Escape Enable register */
31 #define MTK_UART_DMA_EN 0x13 /* DMA Enable register */
32 #define MTK_UART_RXTRI_AD 0x14 /* RX Trigger address */
33 #define MTK_UART_FRACDIV_L 0x15 /* Fractional divider LSB address */
34 #define MTK_UART_FRACDIV_M 0x16 /* Fractional divider MSB address */
35 #define MTK_UART_DEBUG0 0x18
36 #define MTK_UART_IER_XOFFI 0x20 /* Enable XOFF character interrupt */
37 #define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */
38 #define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */
39
40 #define MTK_UART_EFR 38 /* I/O: Extended Features Register */
41 #define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */
42 #define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */
43 #define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */
44 #define MTK_UART_EFR_NO_SW_FC 0x0 /* no sw flow control */
45 #define MTK_UART_EFR_XON1_XOFF1 0xa /* XON1/XOFF1 as sw flow control */
46 #define MTK_UART_EFR_XON2_XOFF2 0x5 /* XON2/XOFF2 as sw flow control */
47 #define MTK_UART_EFR_SW_FC_MASK 0xf /* Enable CTS Modem status interrupt */
48 #define MTK_UART_EFR_HW_FC (MTK_UART_EFR_RTS | MTK_UART_EFR_CTS)
49 #define MTK_UART_DMA_EN_TX 0x2
50 #define MTK_UART_DMA_EN_RX 0x5
51
52 #define MTK_UART_ESCAPE_CHAR 0x77 /* Escape char added under sw fc */
53 #define MTK_UART_RX_SIZE 0x8000
54 #define MTK_UART_TX_TRIGGER 1
55 #define MTK_UART_RX_TRIGGER MTK_UART_RX_SIZE
56
57 #define MTK_UART_XON1 40 /* I/O: Xon character 1 */
58 #define MTK_UART_XOFF1 42 /* I/O: Xoff character 1 */
59
60 #ifdef CONFIG_SERIAL_8250_DMA
61 enum dma_rx_status {
62 DMA_RX_START = 0,
63 DMA_RX_RUNNING = 1,
64 DMA_RX_SHUTDOWN = 2,
65 };
66 #endif
67
68 struct mtk8250_data {
69 int line;
70 unsigned int rx_pos;
71 unsigned int clk_count;
72 struct clk *uart_clk;
73 struct clk *bus_clk;
74 struct uart_8250_dma *dma;
75 #ifdef CONFIG_SERIAL_8250_DMA
76 enum dma_rx_status rx_status;
77 #endif
78 int rx_wakeup_irq;
79 };
80
81 /* flow control mode */
82 enum {
83 MTK_UART_FC_NONE,
84 MTK_UART_FC_SW,
85 MTK_UART_FC_HW,
86 };
87
88 #ifdef CONFIG_SERIAL_8250_DMA
89 static void mtk8250_rx_dma(struct uart_8250_port *up);
90
mtk8250_dma_rx_complete(void * param)91 static void mtk8250_dma_rx_complete(void *param)
92 {
93 struct uart_8250_port *up = param;
94 struct uart_8250_dma *dma = up->dma;
95 struct mtk8250_data *data = up->port.private_data;
96 struct tty_port *tty_port = &up->port.state->port;
97 struct dma_tx_state state;
98 int copied, total, cnt;
99 unsigned char *ptr;
100 unsigned long flags;
101
102 if (data->rx_status == DMA_RX_SHUTDOWN)
103 return;
104
105 spin_lock_irqsave(&up->port.lock, flags);
106
107 dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
108 total = dma->rx_size - state.residue;
109 cnt = total;
110
111 if ((data->rx_pos + cnt) > dma->rx_size)
112 cnt = dma->rx_size - data->rx_pos;
113
114 ptr = (unsigned char *)(data->rx_pos + dma->rx_buf);
115 copied = tty_insert_flip_string(tty_port, ptr, cnt);
116 data->rx_pos += cnt;
117
118 if (total > cnt) {
119 ptr = (unsigned char *)(dma->rx_buf);
120 cnt = total - cnt;
121 copied += tty_insert_flip_string(tty_port, ptr, cnt);
122 data->rx_pos = cnt;
123 }
124
125 up->port.icount.rx += copied;
126
127 tty_flip_buffer_push(tty_port);
128
129 mtk8250_rx_dma(up);
130
131 spin_unlock_irqrestore(&up->port.lock, flags);
132 }
133
mtk8250_rx_dma(struct uart_8250_port * up)134 static void mtk8250_rx_dma(struct uart_8250_port *up)
135 {
136 struct uart_8250_dma *dma = up->dma;
137 struct dma_async_tx_descriptor *desc;
138
139 desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr,
140 dma->rx_size, DMA_DEV_TO_MEM,
141 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
142 if (!desc) {
143 pr_err("failed to prepare rx slave single\n");
144 return;
145 }
146
147 desc->callback = mtk8250_dma_rx_complete;
148 desc->callback_param = up;
149
150 dma->rx_cookie = dmaengine_submit(desc);
151
152 dma_async_issue_pending(dma->rxchan);
153 }
154
mtk8250_dma_enable(struct uart_8250_port * up)155 static void mtk8250_dma_enable(struct uart_8250_port *up)
156 {
157 struct uart_8250_dma *dma = up->dma;
158 struct mtk8250_data *data = up->port.private_data;
159 int lcr = serial_in(up, UART_LCR);
160
161 if (data->rx_status != DMA_RX_START)
162 return;
163
164 dma->rxconf.src_port_window_size = dma->rx_size;
165 dma->rxconf.src_addr = dma->rx_addr;
166
167 dma->txconf.dst_port_window_size = UART_XMIT_SIZE;
168 dma->txconf.dst_addr = dma->tx_addr;
169
170 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR |
171 UART_FCR_CLEAR_XMIT);
172 serial_out(up, MTK_UART_DMA_EN,
173 MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX);
174
175 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
176 serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
177 serial_out(up, UART_LCR, lcr);
178
179 if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0)
180 pr_err("failed to configure rx dma channel\n");
181 if (dmaengine_slave_config(dma->txchan, &dma->txconf) != 0)
182 pr_err("failed to configure tx dma channel\n");
183
184 data->rx_status = DMA_RX_RUNNING;
185 data->rx_pos = 0;
186 mtk8250_rx_dma(up);
187 }
188 #endif
189
mtk8250_startup(struct uart_port * port)190 static int mtk8250_startup(struct uart_port *port)
191 {
192 #ifdef CONFIG_SERIAL_8250_DMA
193 struct uart_8250_port *up = up_to_u8250p(port);
194 struct mtk8250_data *data = port->private_data;
195
196 /* disable DMA for console */
197 if (uart_console(port))
198 up->dma = NULL;
199
200 if (up->dma) {
201 data->rx_status = DMA_RX_START;
202 uart_circ_clear(&port->state->xmit);
203 }
204 #endif
205 memset(&port->icount, 0, sizeof(port->icount));
206
207 return serial8250_do_startup(port);
208 }
209
mtk8250_shutdown(struct uart_port * port)210 static void mtk8250_shutdown(struct uart_port *port)
211 {
212 #ifdef CONFIG_SERIAL_8250_DMA
213 struct uart_8250_port *up = up_to_u8250p(port);
214 struct mtk8250_data *data = port->private_data;
215
216 if (up->dma)
217 data->rx_status = DMA_RX_SHUTDOWN;
218 #endif
219
220 return serial8250_do_shutdown(port);
221 }
222
mtk8250_disable_intrs(struct uart_8250_port * up,int mask)223 static void mtk8250_disable_intrs(struct uart_8250_port *up, int mask)
224 {
225 serial_out(up, UART_IER, serial_in(up, UART_IER) & (~mask));
226 }
227
mtk8250_enable_intrs(struct uart_8250_port * up,int mask)228 static void mtk8250_enable_intrs(struct uart_8250_port *up, int mask)
229 {
230 serial_out(up, UART_IER, serial_in(up, UART_IER) | mask);
231 }
232
mtk8250_set_flow_ctrl(struct uart_8250_port * up,int mode)233 static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
234 {
235 struct uart_port *port = &up->port;
236 int lcr = serial_in(up, UART_LCR);
237
238 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
239 serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
240 serial_out(up, UART_LCR, lcr);
241 lcr = serial_in(up, UART_LCR);
242
243 switch (mode) {
244 case MTK_UART_FC_NONE:
245 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR);
246 serial_out(up, MTK_UART_ESCAPE_EN, 0x00);
247 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
248 serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) &
249 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)));
250 serial_out(up, UART_LCR, lcr);
251 mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI |
252 MTK_UART_IER_RTSI | MTK_UART_IER_CTSI);
253 break;
254
255 case MTK_UART_FC_HW:
256 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR);
257 serial_out(up, MTK_UART_ESCAPE_EN, 0x00);
258 serial_out(up, UART_MCR, UART_MCR_RTS);
259 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
260
261 /*enable hw flow control*/
262 serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC |
263 (serial_in(up, MTK_UART_EFR) &
264 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
265
266 serial_out(up, UART_LCR, lcr);
267 mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI);
268 mtk8250_enable_intrs(up, MTK_UART_IER_CTSI | MTK_UART_IER_RTSI);
269 break;
270
271 case MTK_UART_FC_SW: /*MTK software flow control */
272 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR);
273 serial_out(up, MTK_UART_ESCAPE_EN, 0x01);
274 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
275
276 /*enable sw flow control */
277 serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
278 (serial_in(up, MTK_UART_EFR) &
279 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
280
281 serial_out(up, MTK_UART_XON1, START_CHAR(port->state->port.tty));
282 serial_out(up, MTK_UART_XOFF1, STOP_CHAR(port->state->port.tty));
283 serial_out(up, UART_LCR, lcr);
284 mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI);
285 mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI);
286 break;
287 default:
288 break;
289 }
290 }
291
292 static void
mtk8250_set_termios(struct uart_port * port,struct ktermios * termios,struct ktermios * old)293 mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
294 struct ktermios *old)
295 {
296 unsigned short fraction_L_mapping[] = {
297 0, 1, 0x5, 0x15, 0x55, 0x57, 0x57, 0x77, 0x7F, 0xFF, 0xFF
298 };
299 unsigned short fraction_M_mapping[] = {
300 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3
301 };
302 struct uart_8250_port *up = up_to_u8250p(port);
303 unsigned int baud, quot, fraction;
304 unsigned long flags;
305 int mode;
306
307 #ifdef CONFIG_SERIAL_8250_DMA
308 if (up->dma) {
309 if (uart_console(port)) {
310 devm_kfree(up->port.dev, up->dma);
311 up->dma = NULL;
312 } else {
313 mtk8250_dma_enable(up);
314 }
315 }
316 #endif
317
318 /*
319 * Store the requested baud rate before calling the generic 8250
320 * set_termios method. Standard 8250 port expects bauds to be
321 * no higher than (uartclk / 16) so the baud will be clamped if it
322 * gets out of that bound. Mediatek 8250 port supports speed
323 * higher than that, therefore we'll get original baud rate back
324 * after calling the generic set_termios method and recalculate
325 * the speed later in this method.
326 */
327 baud = tty_termios_baud_rate(termios);
328
329 serial8250_do_set_termios(port, termios, NULL);
330
331 tty_termios_encode_baud_rate(termios, baud, baud);
332
333 /*
334 * Mediatek UARTs use an extra highspeed register (MTK_UART_HIGHS)
335 *
336 * We need to recalcualte the quot register, as the claculation depends
337 * on the vaule in the highspeed register.
338 *
339 * Some baudrates are not supported by the chip, so we use the next
340 * lower rate supported and update termios c_flag.
341 *
342 * If highspeed register is set to 3, we need to specify sample count
343 * and sample point to increase accuracy. If not, we reset the
344 * registers to their default values.
345 */
346 baud = uart_get_baud_rate(port, termios, old,
347 port->uartclk / 16 / UART_DIV_MAX,
348 port->uartclk);
349
350 if (baud < 115200) {
351 serial_port_out(port, MTK_UART_HIGHS, 0x0);
352 quot = uart_get_divisor(port, baud);
353 } else {
354 serial_port_out(port, MTK_UART_HIGHS, 0x3);
355 quot = DIV_ROUND_UP(port->uartclk, 256 * baud);
356 }
357
358 /*
359 * Ok, we're now changing the port state. Do it with
360 * interrupts disabled.
361 */
362 spin_lock_irqsave(&port->lock, flags);
363
364 /*
365 * Update the per-port timeout.
366 */
367 uart_update_timeout(port, termios->c_cflag, baud);
368
369 /* set DLAB we have cval saved in up->lcr from the call to the core */
370 serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
371 serial_dl_write(up, quot);
372
373 /* reset DLAB */
374 serial_port_out(port, UART_LCR, up->lcr);
375
376 if (baud >= 115200) {
377 unsigned int tmp;
378
379 tmp = (port->uartclk / (baud * quot)) - 1;
380 serial_port_out(port, MTK_UART_SAMPLE_COUNT, tmp);
381 serial_port_out(port, MTK_UART_SAMPLE_POINT,
382 (tmp >> 1) - 1);
383
384 /*count fraction to set fractoin register */
385 fraction = ((port->uartclk * 100) / baud / quot) % 100;
386 fraction = DIV_ROUND_CLOSEST(fraction, 10);
387 serial_port_out(port, MTK_UART_FRACDIV_L,
388 fraction_L_mapping[fraction]);
389 serial_port_out(port, MTK_UART_FRACDIV_M,
390 fraction_M_mapping[fraction]);
391 } else {
392 serial_port_out(port, MTK_UART_SAMPLE_COUNT, 0x00);
393 serial_port_out(port, MTK_UART_SAMPLE_POINT, 0xff);
394 serial_port_out(port, MTK_UART_FRACDIV_L, 0x00);
395 serial_port_out(port, MTK_UART_FRACDIV_M, 0x00);
396 }
397
398 if ((termios->c_cflag & CRTSCTS) && (!(termios->c_iflag & CRTSCTS)))
399 mode = MTK_UART_FC_HW;
400 else if (termios->c_iflag & CRTSCTS)
401 mode = MTK_UART_FC_SW;
402 else
403 mode = MTK_UART_FC_NONE;
404
405 mtk8250_set_flow_ctrl(up, mode);
406
407 if (uart_console(port))
408 up->port.cons->cflag = termios->c_cflag;
409
410 spin_unlock_irqrestore(&port->lock, flags);
411 /* Don't rewrite B0 */
412 if (tty_termios_baud_rate(termios))
413 tty_termios_encode_baud_rate(termios, baud, baud);
414 }
415
mtk8250_runtime_suspend(struct device * dev)416 static int __maybe_unused mtk8250_runtime_suspend(struct device *dev)
417 {
418 struct mtk8250_data *data = dev_get_drvdata(dev);
419 struct uart_8250_port *up = serial8250_get_port(data->line);
420
421 /* wait until UART in idle status */
422 while
423 (serial_in(up, MTK_UART_DEBUG0));
424
425 if (data->clk_count == 0U) {
426 dev_dbg(dev, "%s clock count is 0\n", __func__);
427 } else {
428 clk_disable_unprepare(data->bus_clk);
429 data->clk_count--;
430 }
431
432 return 0;
433 }
434
mtk8250_runtime_resume(struct device * dev)435 static int __maybe_unused mtk8250_runtime_resume(struct device *dev)
436 {
437 struct mtk8250_data *data = dev_get_drvdata(dev);
438 int err;
439
440 if (data->clk_count > 0U) {
441 dev_dbg(dev, "%s clock count is %d\n", __func__,
442 data->clk_count);
443 } else {
444 err = clk_prepare_enable(data->bus_clk);
445 if (err) {
446 dev_warn(dev, "Can't enable bus clock\n");
447 return err;
448 }
449 data->clk_count++;
450 }
451
452 return 0;
453 }
454
455 static void
mtk8250_do_pm(struct uart_port * port,unsigned int state,unsigned int old)456 mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
457 {
458 if (!state)
459 if (!mtk8250_runtime_resume(port->dev))
460 pm_runtime_get_sync(port->dev);
461
462 serial8250_do_pm(port, state, old);
463
464 if (state)
465 if (!pm_runtime_put_sync_suspend(port->dev))
466 mtk8250_runtime_suspend(port->dev);
467 }
468
469 #ifdef CONFIG_SERIAL_8250_DMA
mtk8250_dma_filter(struct dma_chan * chan,void * param)470 static bool mtk8250_dma_filter(struct dma_chan *chan, void *param)
471 {
472 return false;
473 }
474 #endif
475
mtk8250_probe_of(struct platform_device * pdev,struct uart_port * p,struct mtk8250_data * data)476 static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p,
477 struct mtk8250_data *data)
478 {
479 #ifdef CONFIG_SERIAL_8250_DMA
480 int dmacnt;
481 #endif
482
483 data->uart_clk = devm_clk_get(&pdev->dev, "baud");
484 if (IS_ERR(data->uart_clk)) {
485 /*
486 * For compatibility with older device trees try unnamed
487 * clk when no baud clk can be found.
488 */
489 data->uart_clk = devm_clk_get(&pdev->dev, NULL);
490 if (IS_ERR(data->uart_clk)) {
491 dev_warn(&pdev->dev, "Can't get uart clock\n");
492 return PTR_ERR(data->uart_clk);
493 }
494
495 return 0;
496 }
497
498 data->bus_clk = devm_clk_get(&pdev->dev, "bus");
499 if (IS_ERR(data->bus_clk))
500 return PTR_ERR(data->bus_clk);
501
502 data->dma = NULL;
503 #ifdef CONFIG_SERIAL_8250_DMA
504 dmacnt = of_property_count_strings(pdev->dev.of_node, "dma-names");
505 if (dmacnt == 2) {
506 data->dma = devm_kzalloc(&pdev->dev, sizeof(*data->dma),
507 GFP_KERNEL);
508 if (!data->dma)
509 return -ENOMEM;
510
511 data->dma->fn = mtk8250_dma_filter;
512 data->dma->rx_size = MTK_UART_RX_SIZE;
513 data->dma->rxconf.src_maxburst = MTK_UART_RX_TRIGGER;
514 data->dma->txconf.dst_maxburst = MTK_UART_TX_TRIGGER;
515 }
516 #endif
517
518 return 0;
519 }
520
mtk8250_probe(struct platform_device * pdev)521 static int mtk8250_probe(struct platform_device *pdev)
522 {
523 struct uart_8250_port uart = {};
524 struct mtk8250_data *data;
525 struct resource *regs;
526 int irq, err;
527
528 irq = platform_get_irq(pdev, 0);
529 if (irq < 0)
530 return irq;
531
532 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
533 if (!regs) {
534 dev_err(&pdev->dev, "no registers defined\n");
535 return -EINVAL;
536 }
537
538 uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
539 resource_size(regs));
540 if (!uart.port.membase)
541 return -ENOMEM;
542
543 data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
544 if (!data)
545 return -ENOMEM;
546
547 data->clk_count = 0;
548
549 if (pdev->dev.of_node) {
550 err = mtk8250_probe_of(pdev, &uart.port, data);
551 if (err)
552 return err;
553 } else
554 return -ENODEV;
555
556 spin_lock_init(&uart.port.lock);
557 uart.port.mapbase = regs->start;
558 uart.port.irq = irq;
559 uart.port.pm = mtk8250_do_pm;
560 uart.port.type = PORT_16550;
561 uart.port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
562 uart.port.dev = &pdev->dev;
563 uart.port.iotype = UPIO_MEM32;
564 uart.port.regshift = 2;
565 uart.port.private_data = data;
566 uart.port.shutdown = mtk8250_shutdown;
567 uart.port.startup = mtk8250_startup;
568 uart.port.set_termios = mtk8250_set_termios;
569 uart.port.uartclk = clk_get_rate(data->uart_clk);
570 #ifdef CONFIG_SERIAL_8250_DMA
571 if (data->dma)
572 uart.dma = data->dma;
573 #endif
574
575 /* Disable Rate Fix function */
576 writel(0x0, uart.port.membase +
577 (MTK_UART_RATE_FIX << uart.port.regshift));
578
579 platform_set_drvdata(pdev, data);
580
581 pm_runtime_enable(&pdev->dev);
582 err = mtk8250_runtime_resume(&pdev->dev);
583 if (err)
584 goto err_pm_disable;
585
586 data->line = serial8250_register_8250_port(&uart);
587 if (data->line < 0) {
588 err = data->line;
589 goto err_pm_disable;
590 }
591
592 data->rx_wakeup_irq = platform_get_irq_optional(pdev, 1);
593
594 return 0;
595
596 err_pm_disable:
597 pm_runtime_disable(&pdev->dev);
598
599 return err;
600 }
601
mtk8250_remove(struct platform_device * pdev)602 static int mtk8250_remove(struct platform_device *pdev)
603 {
604 struct mtk8250_data *data = platform_get_drvdata(pdev);
605
606 pm_runtime_get_sync(&pdev->dev);
607
608 serial8250_unregister_port(data->line);
609
610 pm_runtime_disable(&pdev->dev);
611 pm_runtime_put_noidle(&pdev->dev);
612
613 if (!pm_runtime_status_suspended(&pdev->dev))
614 mtk8250_runtime_suspend(&pdev->dev);
615
616 return 0;
617 }
618
mtk8250_suspend(struct device * dev)619 static int __maybe_unused mtk8250_suspend(struct device *dev)
620 {
621 struct mtk8250_data *data = dev_get_drvdata(dev);
622 int irq = data->rx_wakeup_irq;
623 int err;
624
625 serial8250_suspend_port(data->line);
626
627 pinctrl_pm_select_sleep_state(dev);
628 if (irq >= 0) {
629 err = enable_irq_wake(irq);
630 if (err) {
631 dev_err(dev,
632 "failed to enable irq wake on IRQ %d: %d\n",
633 irq, err);
634 pinctrl_pm_select_default_state(dev);
635 serial8250_resume_port(data->line);
636 return err;
637 }
638 }
639
640 return 0;
641 }
642
mtk8250_resume(struct device * dev)643 static int __maybe_unused mtk8250_resume(struct device *dev)
644 {
645 struct mtk8250_data *data = dev_get_drvdata(dev);
646 int irq = data->rx_wakeup_irq;
647
648 if (irq >= 0)
649 disable_irq_wake(irq);
650 pinctrl_pm_select_default_state(dev);
651
652 serial8250_resume_port(data->line);
653
654 return 0;
655 }
656
657 static const struct dev_pm_ops mtk8250_pm_ops = {
658 SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume)
659 SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume,
660 NULL)
661 };
662
663 static const struct of_device_id mtk8250_of_match[] = {
664 { .compatible = "mediatek,mt6577-uart" },
665 { /* Sentinel */ }
666 };
667 MODULE_DEVICE_TABLE(of, mtk8250_of_match);
668
669 static struct platform_driver mtk8250_platform_driver = {
670 .driver = {
671 .name = "mt6577-uart",
672 .pm = &mtk8250_pm_ops,
673 .of_match_table = mtk8250_of_match,
674 },
675 .probe = mtk8250_probe,
676 .remove = mtk8250_remove,
677 };
678 module_platform_driver(mtk8250_platform_driver);
679
680 #ifdef CONFIG_SERIAL_8250_CONSOLE
early_mtk8250_setup(struct earlycon_device * device,const char * options)681 static int __init early_mtk8250_setup(struct earlycon_device *device,
682 const char *options)
683 {
684 if (!device->port.membase)
685 return -ENODEV;
686
687 device->port.iotype = UPIO_MEM32;
688 device->port.regshift = 2;
689
690 return early_serial8250_setup(device, NULL);
691 }
692
693 OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup);
694 #endif
695
696 MODULE_AUTHOR("Matthias Brugger");
697 MODULE_LICENSE("GPL");
698 MODULE_DESCRIPTION("Mediatek 8250 serial port driver");
699