1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Copyright (C) 2013 - 2015 Fujitsu Semiconductor, Ltd
4 * Vincent Yang <vincent.yang@tw.fujitsu.com>
5 * Copyright (C) 2015 Linaro Ltd Andy Green <andy.green@linaro.org>
6 * Copyright (C) 2019 Socionext Inc.
7 * Takao Orito <orito.takao@socionext.com>
8 */
9
10 #include <linux/bits.h>
11 #include <linux/clk.h>
12 #include <linux/delay.h>
13 #include <linux/err.h>
14 #include <linux/gpio/consumer.h>
15 #include <linux/module.h>
16 #include <linux/of.h>
17 #include <linux/property.h>
18
19 #include "sdhci-pltfm.h"
20 #include "sdhci_f_sdh30.h"
21
22 /* milbeaut bridge controller register */
23 #define MLB_SOFT_RESET 0x0200
24 #define MLB_SOFT_RESET_RSTX BIT(0)
25
26 #define MLB_WP_CD_LED_SET 0x0210
27 #define MLB_WP_CD_LED_SET_LED_INV BIT(2)
28
29 #define MLB_CR_SET 0x0220
30 #define MLB_CR_SET_CR_TOCLKUNIT BIT(24)
31 #define MLB_CR_SET_CR_TOCLKFREQ_SFT (16)
32 #define MLB_CR_SET_CR_TOCLKFREQ_MASK (0x3F << MLB_CR_SET_CR_TOCLKFREQ_SFT)
33 #define MLB_CR_SET_CR_BCLKFREQ_SFT (8)
34 #define MLB_CR_SET_CR_BCLKFREQ_MASK (0xFF << MLB_CR_SET_CR_BCLKFREQ_SFT)
35 #define MLB_CR_SET_CR_RTUNTIMER_SFT (4)
36 #define MLB_CR_SET_CR_RTUNTIMER_MASK (0xF << MLB_CR_SET_CR_RTUNTIMER_SFT)
37
38 #define MLB_SD_TOCLK_I_DIV 16
39 #define MLB_TOCLKFREQ_UNIT_THRES 16000000
40 #define MLB_CAL_TOCLKFREQ_MHZ(rate) (rate / MLB_SD_TOCLK_I_DIV / 1000000)
41 #define MLB_CAL_TOCLKFREQ_KHZ(rate) (rate / MLB_SD_TOCLK_I_DIV / 1000)
42 #define MLB_TOCLKFREQ_MAX 63
43 #define MLB_TOCLKFREQ_MIN 1
44
45 #define MLB_SD_BCLK_I_DIV 4
46 #define MLB_CAL_BCLKFREQ(rate) (rate / MLB_SD_BCLK_I_DIV / 1000000)
47 #define MLB_BCLKFREQ_MAX 255
48 #define MLB_BCLKFREQ_MIN 1
49
50 #define MLB_CDR_SET 0x0230
51 #define MLB_CDR_SET_CLK2POW16 3
52
53 struct f_sdhost_priv {
54 struct clk *clk_iface;
55 struct clk *clk;
56 struct device *dev;
57 bool enable_cmd_dat_delay;
58 };
59
sdhci_milbeaut_soft_voltage_switch(struct sdhci_host * host)60 static void sdhci_milbeaut_soft_voltage_switch(struct sdhci_host *host)
61 {
62 u32 ctrl = 0;
63
64 usleep_range(2500, 3000);
65 ctrl = sdhci_readl(host, F_SDH30_IO_CONTROL2);
66 ctrl |= F_SDH30_CRES_O_DN;
67 sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
68 ctrl |= F_SDH30_MSEL_O_1_8;
69 sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
70
71 ctrl &= ~F_SDH30_CRES_O_DN;
72 sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
73 usleep_range(2500, 3000);
74
75 ctrl = sdhci_readl(host, F_SDH30_TUNING_SETTING);
76 ctrl |= F_SDH30_CMD_CHK_DIS;
77 sdhci_writel(host, ctrl, F_SDH30_TUNING_SETTING);
78 }
79
sdhci_milbeaut_get_min_clock(struct sdhci_host * host)80 static unsigned int sdhci_milbeaut_get_min_clock(struct sdhci_host *host)
81 {
82 return F_SDH30_MIN_CLOCK;
83 }
84
sdhci_milbeaut_reset(struct sdhci_host * host,u8 mask)85 static void sdhci_milbeaut_reset(struct sdhci_host *host, u8 mask)
86 {
87 struct f_sdhost_priv *priv = sdhci_priv(host);
88 u16 clk;
89 u32 ctl;
90 ktime_t timeout;
91
92 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
93 clk = (clk & ~SDHCI_CLOCK_CARD_EN) | SDHCI_CLOCK_INT_EN;
94 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
95
96 sdhci_reset(host, mask);
97
98 clk |= SDHCI_CLOCK_CARD_EN;
99 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
100
101 timeout = ktime_add_ms(ktime_get(), 10);
102 while (1) {
103 bool timedout = ktime_after(ktime_get(), timeout);
104
105 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
106 if (clk & SDHCI_CLOCK_INT_STABLE)
107 break;
108 if (timedout) {
109 pr_err("%s: Internal clock never stabilised.\n",
110 mmc_hostname(host->mmc));
111 sdhci_dumpregs(host);
112 return;
113 }
114 udelay(10);
115 }
116
117 if (priv->enable_cmd_dat_delay) {
118 ctl = sdhci_readl(host, F_SDH30_ESD_CONTROL);
119 ctl |= F_SDH30_CMD_DAT_DELAY;
120 sdhci_writel(host, ctl, F_SDH30_ESD_CONTROL);
121 }
122 }
123
124 static const struct sdhci_ops sdhci_milbeaut_ops = {
125 .voltage_switch = sdhci_milbeaut_soft_voltage_switch,
126 .get_min_clock = sdhci_milbeaut_get_min_clock,
127 .reset = sdhci_milbeaut_reset,
128 .set_clock = sdhci_set_clock,
129 .set_bus_width = sdhci_set_bus_width,
130 .set_uhs_signaling = sdhci_set_uhs_signaling,
131 .set_power = sdhci_set_power_and_bus_voltage,
132 };
133
sdhci_milbeaut_bridge_reset(struct sdhci_host * host,int reset_flag)134 static void sdhci_milbeaut_bridge_reset(struct sdhci_host *host,
135 int reset_flag)
136 {
137 if (reset_flag)
138 sdhci_writel(host, 0, MLB_SOFT_RESET);
139 else
140 sdhci_writel(host, MLB_SOFT_RESET_RSTX, MLB_SOFT_RESET);
141 }
142
sdhci_milbeaut_bridge_init(struct sdhci_host * host,int rate)143 static void sdhci_milbeaut_bridge_init(struct sdhci_host *host,
144 int rate)
145 {
146 u32 val, clk;
147
148 /* IO_SDIO_CR_SET should be set while reset */
149 val = sdhci_readl(host, MLB_CR_SET);
150 val &= ~(MLB_CR_SET_CR_TOCLKFREQ_MASK | MLB_CR_SET_CR_TOCLKUNIT |
151 MLB_CR_SET_CR_BCLKFREQ_MASK);
152 if (rate >= MLB_TOCLKFREQ_UNIT_THRES) {
153 clk = MLB_CAL_TOCLKFREQ_MHZ(rate);
154 clk = min_t(u32, MLB_TOCLKFREQ_MAX, clk);
155 val |= MLB_CR_SET_CR_TOCLKUNIT |
156 (clk << MLB_CR_SET_CR_TOCLKFREQ_SFT);
157 } else {
158 clk = MLB_CAL_TOCLKFREQ_KHZ(rate);
159 clk = min_t(u32, MLB_TOCLKFREQ_MAX, clk);
160 clk = max_t(u32, MLB_TOCLKFREQ_MIN, clk);
161 val |= clk << MLB_CR_SET_CR_TOCLKFREQ_SFT;
162 }
163
164 clk = MLB_CAL_BCLKFREQ(rate);
165 clk = min_t(u32, MLB_BCLKFREQ_MAX, clk);
166 clk = max_t(u32, MLB_BCLKFREQ_MIN, clk);
167 val |= clk << MLB_CR_SET_CR_BCLKFREQ_SFT;
168 val &= ~MLB_CR_SET_CR_RTUNTIMER_MASK;
169 sdhci_writel(host, val, MLB_CR_SET);
170
171 sdhci_writel(host, MLB_CDR_SET_CLK2POW16, MLB_CDR_SET);
172
173 sdhci_writel(host, MLB_WP_CD_LED_SET_LED_INV, MLB_WP_CD_LED_SET);
174 }
175
sdhci_milbeaut_vendor_init(struct sdhci_host * host)176 static void sdhci_milbeaut_vendor_init(struct sdhci_host *host)
177 {
178 struct f_sdhost_priv *priv = sdhci_priv(host);
179 u32 ctl;
180
181 ctl = sdhci_readl(host, F_SDH30_IO_CONTROL2);
182 ctl |= F_SDH30_CRES_O_DN;
183 sdhci_writel(host, ctl, F_SDH30_IO_CONTROL2);
184 ctl &= ~F_SDH30_MSEL_O_1_8;
185 sdhci_writel(host, ctl, F_SDH30_IO_CONTROL2);
186 ctl &= ~F_SDH30_CRES_O_DN;
187 sdhci_writel(host, ctl, F_SDH30_IO_CONTROL2);
188
189 ctl = sdhci_readw(host, F_SDH30_AHB_CONFIG);
190 ctl |= F_SDH30_SIN | F_SDH30_AHB_INCR_16 | F_SDH30_AHB_INCR_8 |
191 F_SDH30_AHB_INCR_4;
192 ctl &= ~(F_SDH30_AHB_BIGED | F_SDH30_BUSLOCK_EN);
193 sdhci_writew(host, ctl, F_SDH30_AHB_CONFIG);
194
195 if (priv->enable_cmd_dat_delay) {
196 ctl = sdhci_readl(host, F_SDH30_ESD_CONTROL);
197 ctl |= F_SDH30_CMD_DAT_DELAY;
198 sdhci_writel(host, ctl, F_SDH30_ESD_CONTROL);
199 }
200 }
201
202 static const struct of_device_id mlb_dt_ids[] = {
203 {
204 .compatible = "socionext,milbeaut-m10v-sdhci-3.0",
205 },
206 { /* sentinel */ }
207 };
208 MODULE_DEVICE_TABLE(of, mlb_dt_ids);
209
sdhci_milbeaut_init(struct sdhci_host * host)210 static void sdhci_milbeaut_init(struct sdhci_host *host)
211 {
212 struct f_sdhost_priv *priv = sdhci_priv(host);
213 int rate = clk_get_rate(priv->clk);
214 u16 ctl;
215
216 sdhci_milbeaut_bridge_reset(host, 0);
217
218 ctl = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
219 ctl &= ~(SDHCI_CLOCK_CARD_EN | SDHCI_CLOCK_INT_EN);
220 sdhci_writew(host, ctl, SDHCI_CLOCK_CONTROL);
221
222 sdhci_milbeaut_bridge_reset(host, 1);
223
224 sdhci_milbeaut_bridge_init(host, rate);
225 sdhci_milbeaut_bridge_reset(host, 0);
226
227 sdhci_milbeaut_vendor_init(host);
228 }
229
sdhci_milbeaut_probe(struct platform_device * pdev)230 static int sdhci_milbeaut_probe(struct platform_device *pdev)
231 {
232 struct sdhci_host *host;
233 struct device *dev = &pdev->dev;
234 int irq, ret = 0;
235 struct f_sdhost_priv *priv;
236
237 irq = platform_get_irq(pdev, 0);
238 if (irq < 0)
239 return irq;
240
241 host = sdhci_alloc_host(dev, sizeof(struct f_sdhost_priv));
242 if (IS_ERR(host))
243 return PTR_ERR(host);
244
245 priv = sdhci_priv(host);
246 priv->dev = dev;
247
248 host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
249 SDHCI_QUIRK_INVERTED_WRITE_PROTECT |
250 SDHCI_QUIRK_CLOCK_BEFORE_RESET |
251 SDHCI_QUIRK_DELAY_AFTER_POWER;
252 host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE |
253 SDHCI_QUIRK2_TUNING_WORK_AROUND |
254 SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
255
256 priv->enable_cmd_dat_delay = device_property_read_bool(dev,
257 "fujitsu,cmd-dat-delay-select");
258
259 ret = mmc_of_parse(host->mmc);
260 if (ret)
261 goto err;
262
263 platform_set_drvdata(pdev, host);
264
265 host->hw_name = "f_sdh30";
266 host->ops = &sdhci_milbeaut_ops;
267 host->irq = irq;
268
269 host->ioaddr = devm_platform_ioremap_resource(pdev, 0);
270 if (IS_ERR(host->ioaddr)) {
271 ret = PTR_ERR(host->ioaddr);
272 goto err;
273 }
274
275 if (dev_of_node(dev)) {
276 sdhci_get_of_property(pdev);
277
278 priv->clk_iface = devm_clk_get(&pdev->dev, "iface");
279 if (IS_ERR(priv->clk_iface)) {
280 ret = PTR_ERR(priv->clk_iface);
281 goto err;
282 }
283
284 ret = clk_prepare_enable(priv->clk_iface);
285 if (ret)
286 goto err;
287
288 priv->clk = devm_clk_get(&pdev->dev, "core");
289 if (IS_ERR(priv->clk)) {
290 ret = PTR_ERR(priv->clk);
291 goto err_clk;
292 }
293
294 ret = clk_prepare_enable(priv->clk);
295 if (ret)
296 goto err_clk;
297 }
298
299 sdhci_milbeaut_init(host);
300
301 ret = sdhci_add_host(host);
302 if (ret)
303 goto err_add_host;
304
305 return 0;
306
307 err_add_host:
308 clk_disable_unprepare(priv->clk);
309 err_clk:
310 clk_disable_unprepare(priv->clk_iface);
311 err:
312 sdhci_free_host(host);
313 return ret;
314 }
315
sdhci_milbeaut_remove(struct platform_device * pdev)316 static int sdhci_milbeaut_remove(struct platform_device *pdev)
317 {
318 struct sdhci_host *host = platform_get_drvdata(pdev);
319 struct f_sdhost_priv *priv = sdhci_priv(host);
320
321 sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) ==
322 0xffffffff);
323
324 clk_disable_unprepare(priv->clk_iface);
325 clk_disable_unprepare(priv->clk);
326
327 sdhci_free_host(host);
328 platform_set_drvdata(pdev, NULL);
329
330 return 0;
331 }
332
333 static struct platform_driver sdhci_milbeaut_driver = {
334 .driver = {
335 .name = "sdhci-milbeaut",
336 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
337 .of_match_table = of_match_ptr(mlb_dt_ids),
338 },
339 .probe = sdhci_milbeaut_probe,
340 .remove = sdhci_milbeaut_remove,
341 };
342
343 module_platform_driver(sdhci_milbeaut_driver);
344
345 MODULE_DESCRIPTION("MILBEAUT SD Card Controller driver");
346 MODULE_AUTHOR("Takao Orito <orito.takao@socionext.com>");
347 MODULE_LICENSE("GPL v2");
348 MODULE_ALIAS("platform:sdhci-milbeaut");
349