1 // SPDX-License-Identifier: GPL-2.0
2 /* Copyright(c) 1999 - 2018 Intel Corporation. */
3
4 #include <linux/pci.h>
5 #include <linux/delay.h>
6 #include <linux/sched.h>
7 #include <linux/netdevice.h>
8
9 #include "ixgbe.h"
10 #include "ixgbe_common.h"
11 #include "ixgbe_phy.h"
12
13 static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw);
14 static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw);
15 static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw);
16 static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw);
17 static void ixgbe_standby_eeprom(struct ixgbe_hw *hw);
18 static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
19 u16 count);
20 static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count);
21 static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
22 static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
23 static void ixgbe_release_eeprom(struct ixgbe_hw *hw);
24
25 static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr);
26 static s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg);
27 static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
28 u16 words, u16 *data);
29 static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
30 u16 words, u16 *data);
31 static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
32 u16 offset);
33 static s32 ixgbe_disable_pcie_primary(struct ixgbe_hw *hw);
34
35 /* Base table for registers values that change by MAC */
36 const u32 ixgbe_mvals_8259X[IXGBE_MVALS_IDX_LIMIT] = {
37 IXGBE_MVALS_INIT(8259X)
38 };
39
40 /**
41 * ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
42 * control
43 * @hw: pointer to hardware structure
44 *
45 * There are several phys that do not support autoneg flow control. This
46 * function check the device id to see if the associated phy supports
47 * autoneg flow control.
48 **/
ixgbe_device_supports_autoneg_fc(struct ixgbe_hw * hw)49 bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
50 {
51 bool supported = false;
52 ixgbe_link_speed speed;
53 bool link_up;
54
55 switch (hw->phy.media_type) {
56 case ixgbe_media_type_fiber:
57 /* flow control autoneg black list */
58 switch (hw->device_id) {
59 case IXGBE_DEV_ID_X550EM_A_SFP:
60 case IXGBE_DEV_ID_X550EM_A_SFP_N:
61 supported = false;
62 break;
63 default:
64 hw->mac.ops.check_link(hw, &speed, &link_up, false);
65 /* if link is down, assume supported */
66 if (link_up)
67 supported = speed == IXGBE_LINK_SPEED_1GB_FULL;
68 else
69 supported = true;
70 }
71
72 break;
73 case ixgbe_media_type_backplane:
74 if (hw->device_id == IXGBE_DEV_ID_X550EM_X_XFI)
75 supported = false;
76 else
77 supported = true;
78 break;
79 case ixgbe_media_type_copper:
80 /* only some copper devices support flow control autoneg */
81 switch (hw->device_id) {
82 case IXGBE_DEV_ID_82599_T3_LOM:
83 case IXGBE_DEV_ID_X540T:
84 case IXGBE_DEV_ID_X540T1:
85 case IXGBE_DEV_ID_X550T:
86 case IXGBE_DEV_ID_X550T1:
87 case IXGBE_DEV_ID_X550EM_X_10G_T:
88 case IXGBE_DEV_ID_X550EM_A_10G_T:
89 case IXGBE_DEV_ID_X550EM_A_1G_T:
90 case IXGBE_DEV_ID_X550EM_A_1G_T_L:
91 supported = true;
92 break;
93 default:
94 break;
95 }
96 break;
97 default:
98 break;
99 }
100
101 if (!supported)
102 hw_dbg(hw, "Device %x does not support flow control autoneg\n",
103 hw->device_id);
104
105 return supported;
106 }
107
108 /**
109 * ixgbe_setup_fc_generic - Set up flow control
110 * @hw: pointer to hardware structure
111 *
112 * Called at init time to set up flow control.
113 **/
ixgbe_setup_fc_generic(struct ixgbe_hw * hw)114 s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw)
115 {
116 s32 ret_val = 0;
117 u32 reg = 0, reg_bp = 0;
118 u16 reg_cu = 0;
119 bool locked = false;
120
121 /*
122 * Validate the requested mode. Strict IEEE mode does not allow
123 * ixgbe_fc_rx_pause because it will cause us to fail at UNH.
124 */
125 if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
126 hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
127 return -EINVAL;
128 }
129
130 /*
131 * 10gig parts do not have a word in the EEPROM to determine the
132 * default flow control setting, so we explicitly set it to full.
133 */
134 if (hw->fc.requested_mode == ixgbe_fc_default)
135 hw->fc.requested_mode = ixgbe_fc_full;
136
137 /*
138 * Set up the 1G and 10G flow control advertisement registers so the
139 * HW will be able to do fc autoneg once the cable is plugged in. If
140 * we link at 10G, the 1G advertisement is harmless and vice versa.
141 */
142 switch (hw->phy.media_type) {
143 case ixgbe_media_type_backplane:
144 /* some MAC's need RMW protection on AUTOC */
145 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, ®_bp);
146 if (ret_val)
147 return ret_val;
148
149 fallthrough; /* only backplane uses autoc */
150 case ixgbe_media_type_fiber:
151 reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
152
153 break;
154 case ixgbe_media_type_copper:
155 hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
156 MDIO_MMD_AN, ®_cu);
157 break;
158 default:
159 break;
160 }
161
162 /*
163 * The possible values of fc.requested_mode are:
164 * 0: Flow control is completely disabled
165 * 1: Rx flow control is enabled (we can receive pause frames,
166 * but not send pause frames).
167 * 2: Tx flow control is enabled (we can send pause frames but
168 * we do not support receiving pause frames).
169 * 3: Both Rx and Tx flow control (symmetric) are enabled.
170 * other: Invalid.
171 */
172 switch (hw->fc.requested_mode) {
173 case ixgbe_fc_none:
174 /* Flow control completely disabled by software override. */
175 reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
176 if (hw->phy.media_type == ixgbe_media_type_backplane)
177 reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
178 IXGBE_AUTOC_ASM_PAUSE);
179 else if (hw->phy.media_type == ixgbe_media_type_copper)
180 reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
181 break;
182 case ixgbe_fc_tx_pause:
183 /*
184 * Tx Flow control is enabled, and Rx Flow control is
185 * disabled by software override.
186 */
187 reg |= IXGBE_PCS1GANA_ASM_PAUSE;
188 reg &= ~IXGBE_PCS1GANA_SYM_PAUSE;
189 if (hw->phy.media_type == ixgbe_media_type_backplane) {
190 reg_bp |= IXGBE_AUTOC_ASM_PAUSE;
191 reg_bp &= ~IXGBE_AUTOC_SYM_PAUSE;
192 } else if (hw->phy.media_type == ixgbe_media_type_copper) {
193 reg_cu |= IXGBE_TAF_ASM_PAUSE;
194 reg_cu &= ~IXGBE_TAF_SYM_PAUSE;
195 }
196 break;
197 case ixgbe_fc_rx_pause:
198 /*
199 * Rx Flow control is enabled and Tx Flow control is
200 * disabled by software override. Since there really
201 * isn't a way to advertise that we are capable of RX
202 * Pause ONLY, we will advertise that we support both
203 * symmetric and asymmetric Rx PAUSE, as such we fall
204 * through to the fc_full statement. Later, we will
205 * disable the adapter's ability to send PAUSE frames.
206 */
207 case ixgbe_fc_full:
208 /* Flow control (both Rx and Tx) is enabled by SW override. */
209 reg |= IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE;
210 if (hw->phy.media_type == ixgbe_media_type_backplane)
211 reg_bp |= IXGBE_AUTOC_SYM_PAUSE |
212 IXGBE_AUTOC_ASM_PAUSE;
213 else if (hw->phy.media_type == ixgbe_media_type_copper)
214 reg_cu |= IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE;
215 break;
216 default:
217 hw_dbg(hw, "Flow control param set incorrectly\n");
218 return -EIO;
219 }
220
221 if (hw->mac.type != ixgbe_mac_X540) {
222 /*
223 * Enable auto-negotiation between the MAC & PHY;
224 * the MAC will advertise clause 37 flow control.
225 */
226 IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
227 reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
228
229 /* Disable AN timeout */
230 if (hw->fc.strict_ieee)
231 reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
232
233 IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
234 hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
235 }
236
237 /*
238 * AUTOC restart handles negotiation of 1G and 10G on backplane
239 * and copper. There is no need to set the PCS1GCTL register.
240 *
241 */
242 if (hw->phy.media_type == ixgbe_media_type_backplane) {
243 /* Need the SW/FW semaphore around AUTOC writes if 82599 and
244 * LESM is on, likewise reset_pipeline requries the lock as
245 * it also writes AUTOC.
246 */
247 ret_val = hw->mac.ops.prot_autoc_write(hw, reg_bp, locked);
248 if (ret_val)
249 return ret_val;
250
251 } else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
252 ixgbe_device_supports_autoneg_fc(hw)) {
253 hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
254 MDIO_MMD_AN, reg_cu);
255 }
256
257 hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
258 return ret_val;
259 }
260
261 /**
262 * ixgbe_start_hw_generic - Prepare hardware for Tx/Rx
263 * @hw: pointer to hardware structure
264 *
265 * Starts the hardware by filling the bus info structure and media type, clears
266 * all on chip counters, initializes receive address registers, multicast
267 * table, VLAN filter table, calls routine to set up link and flow control
268 * settings, and leaves transmit and receive units disabled and uninitialized
269 **/
ixgbe_start_hw_generic(struct ixgbe_hw * hw)270 s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw)
271 {
272 s32 ret_val;
273 u32 ctrl_ext;
274 u16 device_caps;
275
276 /* Set the media type */
277 hw->phy.media_type = hw->mac.ops.get_media_type(hw);
278
279 /* Identify the PHY */
280 hw->phy.ops.identify(hw);
281
282 /* Clear the VLAN filter table */
283 hw->mac.ops.clear_vfta(hw);
284
285 /* Clear statistics registers */
286 hw->mac.ops.clear_hw_cntrs(hw);
287
288 /* Set No Snoop Disable */
289 ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT);
290 ctrl_ext |= IXGBE_CTRL_EXT_NS_DIS;
291 IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext);
292 IXGBE_WRITE_FLUSH(hw);
293
294 /* Setup flow control if method for doing so */
295 if (hw->mac.ops.setup_fc) {
296 ret_val = hw->mac.ops.setup_fc(hw);
297 if (ret_val)
298 return ret_val;
299 }
300
301 /* Cashe bit indicating need for crosstalk fix */
302 switch (hw->mac.type) {
303 case ixgbe_mac_82599EB:
304 case ixgbe_mac_X550EM_x:
305 case ixgbe_mac_x550em_a:
306 hw->mac.ops.get_device_caps(hw, &device_caps);
307 if (device_caps & IXGBE_DEVICE_CAPS_NO_CROSSTALK_WR)
308 hw->need_crosstalk_fix = false;
309 else
310 hw->need_crosstalk_fix = true;
311 break;
312 default:
313 hw->need_crosstalk_fix = false;
314 break;
315 }
316
317 /* Clear adapter stopped flag */
318 hw->adapter_stopped = false;
319
320 return 0;
321 }
322
323 /**
324 * ixgbe_start_hw_gen2 - Init sequence for common device family
325 * @hw: pointer to hw structure
326 *
327 * Performs the init sequence common to the second generation
328 * of 10 GbE devices.
329 * Devices in the second generation:
330 * 82599
331 * X540
332 **/
ixgbe_start_hw_gen2(struct ixgbe_hw * hw)333 s32 ixgbe_start_hw_gen2(struct ixgbe_hw *hw)
334 {
335 u32 i;
336
337 /* Clear the rate limiters */
338 for (i = 0; i < hw->mac.max_tx_queues; i++) {
339 IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, i);
340 IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, 0);
341 }
342 IXGBE_WRITE_FLUSH(hw);
343
344 return 0;
345 }
346
347 /**
348 * ixgbe_init_hw_generic - Generic hardware initialization
349 * @hw: pointer to hardware structure
350 *
351 * Initialize the hardware by resetting the hardware, filling the bus info
352 * structure and media type, clears all on chip counters, initializes receive
353 * address registers, multicast table, VLAN filter table, calls routine to set
354 * up link and flow control settings, and leaves transmit and receive units
355 * disabled and uninitialized
356 **/
ixgbe_init_hw_generic(struct ixgbe_hw * hw)357 s32 ixgbe_init_hw_generic(struct ixgbe_hw *hw)
358 {
359 s32 status;
360
361 /* Reset the hardware */
362 status = hw->mac.ops.reset_hw(hw);
363
364 if (status == 0) {
365 /* Start the HW */
366 status = hw->mac.ops.start_hw(hw);
367 }
368
369 /* Initialize the LED link active for LED blink support */
370 if (hw->mac.ops.init_led_link_act)
371 hw->mac.ops.init_led_link_act(hw);
372
373 return status;
374 }
375
376 /**
377 * ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters
378 * @hw: pointer to hardware structure
379 *
380 * Clears all hardware statistics counters by reading them from the hardware
381 * Statistics counters are clear on read.
382 **/
ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw * hw)383 s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw)
384 {
385 u16 i = 0;
386
387 IXGBE_READ_REG(hw, IXGBE_CRCERRS);
388 IXGBE_READ_REG(hw, IXGBE_ILLERRC);
389 IXGBE_READ_REG(hw, IXGBE_ERRBC);
390 IXGBE_READ_REG(hw, IXGBE_MSPDC);
391 for (i = 0; i < 8; i++)
392 IXGBE_READ_REG(hw, IXGBE_MPC(i));
393
394 IXGBE_READ_REG(hw, IXGBE_MLFC);
395 IXGBE_READ_REG(hw, IXGBE_MRFC);
396 IXGBE_READ_REG(hw, IXGBE_RLEC);
397 IXGBE_READ_REG(hw, IXGBE_LXONTXC);
398 IXGBE_READ_REG(hw, IXGBE_LXOFFTXC);
399 if (hw->mac.type >= ixgbe_mac_82599EB) {
400 IXGBE_READ_REG(hw, IXGBE_LXONRXCNT);
401 IXGBE_READ_REG(hw, IXGBE_LXOFFRXCNT);
402 } else {
403 IXGBE_READ_REG(hw, IXGBE_LXONRXC);
404 IXGBE_READ_REG(hw, IXGBE_LXOFFRXC);
405 }
406
407 for (i = 0; i < 8; i++) {
408 IXGBE_READ_REG(hw, IXGBE_PXONTXC(i));
409 IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i));
410 if (hw->mac.type >= ixgbe_mac_82599EB) {
411 IXGBE_READ_REG(hw, IXGBE_PXONRXCNT(i));
412 IXGBE_READ_REG(hw, IXGBE_PXOFFRXCNT(i));
413 } else {
414 IXGBE_READ_REG(hw, IXGBE_PXONRXC(i));
415 IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i));
416 }
417 }
418 if (hw->mac.type >= ixgbe_mac_82599EB)
419 for (i = 0; i < 8; i++)
420 IXGBE_READ_REG(hw, IXGBE_PXON2OFFCNT(i));
421 IXGBE_READ_REG(hw, IXGBE_PRC64);
422 IXGBE_READ_REG(hw, IXGBE_PRC127);
423 IXGBE_READ_REG(hw, IXGBE_PRC255);
424 IXGBE_READ_REG(hw, IXGBE_PRC511);
425 IXGBE_READ_REG(hw, IXGBE_PRC1023);
426 IXGBE_READ_REG(hw, IXGBE_PRC1522);
427 IXGBE_READ_REG(hw, IXGBE_GPRC);
428 IXGBE_READ_REG(hw, IXGBE_BPRC);
429 IXGBE_READ_REG(hw, IXGBE_MPRC);
430 IXGBE_READ_REG(hw, IXGBE_GPTC);
431 IXGBE_READ_REG(hw, IXGBE_GORCL);
432 IXGBE_READ_REG(hw, IXGBE_GORCH);
433 IXGBE_READ_REG(hw, IXGBE_GOTCL);
434 IXGBE_READ_REG(hw, IXGBE_GOTCH);
435 if (hw->mac.type == ixgbe_mac_82598EB)
436 for (i = 0; i < 8; i++)
437 IXGBE_READ_REG(hw, IXGBE_RNBC(i));
438 IXGBE_READ_REG(hw, IXGBE_RUC);
439 IXGBE_READ_REG(hw, IXGBE_RFC);
440 IXGBE_READ_REG(hw, IXGBE_ROC);
441 IXGBE_READ_REG(hw, IXGBE_RJC);
442 IXGBE_READ_REG(hw, IXGBE_MNGPRC);
443 IXGBE_READ_REG(hw, IXGBE_MNGPDC);
444 IXGBE_READ_REG(hw, IXGBE_MNGPTC);
445 IXGBE_READ_REG(hw, IXGBE_TORL);
446 IXGBE_READ_REG(hw, IXGBE_TORH);
447 IXGBE_READ_REG(hw, IXGBE_TPR);
448 IXGBE_READ_REG(hw, IXGBE_TPT);
449 IXGBE_READ_REG(hw, IXGBE_PTC64);
450 IXGBE_READ_REG(hw, IXGBE_PTC127);
451 IXGBE_READ_REG(hw, IXGBE_PTC255);
452 IXGBE_READ_REG(hw, IXGBE_PTC511);
453 IXGBE_READ_REG(hw, IXGBE_PTC1023);
454 IXGBE_READ_REG(hw, IXGBE_PTC1522);
455 IXGBE_READ_REG(hw, IXGBE_MPTC);
456 IXGBE_READ_REG(hw, IXGBE_BPTC);
457 for (i = 0; i < 16; i++) {
458 IXGBE_READ_REG(hw, IXGBE_QPRC(i));
459 IXGBE_READ_REG(hw, IXGBE_QPTC(i));
460 if (hw->mac.type >= ixgbe_mac_82599EB) {
461 IXGBE_READ_REG(hw, IXGBE_QBRC_L(i));
462 IXGBE_READ_REG(hw, IXGBE_QBRC_H(i));
463 IXGBE_READ_REG(hw, IXGBE_QBTC_L(i));
464 IXGBE_READ_REG(hw, IXGBE_QBTC_H(i));
465 IXGBE_READ_REG(hw, IXGBE_QPRDC(i));
466 } else {
467 IXGBE_READ_REG(hw, IXGBE_QBRC(i));
468 IXGBE_READ_REG(hw, IXGBE_QBTC(i));
469 }
470 }
471
472 if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) {
473 if (hw->phy.id == 0)
474 hw->phy.ops.identify(hw);
475 hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, MDIO_MMD_PCS, &i);
476 hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECH, MDIO_MMD_PCS, &i);
477 hw->phy.ops.read_reg(hw, IXGBE_LDPCECL, MDIO_MMD_PCS, &i);
478 hw->phy.ops.read_reg(hw, IXGBE_LDPCECH, MDIO_MMD_PCS, &i);
479 }
480
481 return 0;
482 }
483
484 /**
485 * ixgbe_read_pba_string_generic - Reads part number string from EEPROM
486 * @hw: pointer to hardware structure
487 * @pba_num: stores the part number string from the EEPROM
488 * @pba_num_size: part number string buffer length
489 *
490 * Reads the part number string from the EEPROM.
491 **/
ixgbe_read_pba_string_generic(struct ixgbe_hw * hw,u8 * pba_num,u32 pba_num_size)492 s32 ixgbe_read_pba_string_generic(struct ixgbe_hw *hw, u8 *pba_num,
493 u32 pba_num_size)
494 {
495 s32 ret_val;
496 u16 data;
497 u16 pba_ptr;
498 u16 offset;
499 u16 length;
500
501 if (pba_num == NULL) {
502 hw_dbg(hw, "PBA string buffer was null\n");
503 return -EINVAL;
504 }
505
506 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data);
507 if (ret_val) {
508 hw_dbg(hw, "NVM Read Error\n");
509 return ret_val;
510 }
511
512 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &pba_ptr);
513 if (ret_val) {
514 hw_dbg(hw, "NVM Read Error\n");
515 return ret_val;
516 }
517
518 /*
519 * if data is not ptr guard the PBA must be in legacy format which
520 * means pba_ptr is actually our second data word for the PBA number
521 * and we can decode it into an ascii string
522 */
523 if (data != IXGBE_PBANUM_PTR_GUARD) {
524 hw_dbg(hw, "NVM PBA number is not stored as string\n");
525
526 /* we will need 11 characters to store the PBA */
527 if (pba_num_size < 11) {
528 hw_dbg(hw, "PBA string buffer too small\n");
529 return -ENOSPC;
530 }
531
532 /* extract hex string from data and pba_ptr */
533 pba_num[0] = (data >> 12) & 0xF;
534 pba_num[1] = (data >> 8) & 0xF;
535 pba_num[2] = (data >> 4) & 0xF;
536 pba_num[3] = data & 0xF;
537 pba_num[4] = (pba_ptr >> 12) & 0xF;
538 pba_num[5] = (pba_ptr >> 8) & 0xF;
539 pba_num[6] = '-';
540 pba_num[7] = 0;
541 pba_num[8] = (pba_ptr >> 4) & 0xF;
542 pba_num[9] = pba_ptr & 0xF;
543
544 /* put a null character on the end of our string */
545 pba_num[10] = '\0';
546
547 /* switch all the data but the '-' to hex char */
548 for (offset = 0; offset < 10; offset++) {
549 if (pba_num[offset] < 0xA)
550 pba_num[offset] += '0';
551 else if (pba_num[offset] < 0x10)
552 pba_num[offset] += 'A' - 0xA;
553 }
554
555 return 0;
556 }
557
558 ret_val = hw->eeprom.ops.read(hw, pba_ptr, &length);
559 if (ret_val) {
560 hw_dbg(hw, "NVM Read Error\n");
561 return ret_val;
562 }
563
564 if (length == 0xFFFF || length == 0) {
565 hw_dbg(hw, "NVM PBA number section invalid length\n");
566 return -EIO;
567 }
568
569 /* check if pba_num buffer is big enough */
570 if (pba_num_size < (((u32)length * 2) - 1)) {
571 hw_dbg(hw, "PBA string buffer too small\n");
572 return -ENOSPC;
573 }
574
575 /* trim pba length from start of string */
576 pba_ptr++;
577 length--;
578
579 for (offset = 0; offset < length; offset++) {
580 ret_val = hw->eeprom.ops.read(hw, pba_ptr + offset, &data);
581 if (ret_val) {
582 hw_dbg(hw, "NVM Read Error\n");
583 return ret_val;
584 }
585 pba_num[offset * 2] = (u8)(data >> 8);
586 pba_num[(offset * 2) + 1] = (u8)(data & 0xFF);
587 }
588 pba_num[offset * 2] = '\0';
589
590 return 0;
591 }
592
593 /**
594 * ixgbe_get_mac_addr_generic - Generic get MAC address
595 * @hw: pointer to hardware structure
596 * @mac_addr: Adapter MAC address
597 *
598 * Reads the adapter's MAC address from first Receive Address Register (RAR0)
599 * A reset of the adapter must be performed prior to calling this function
600 * in order for the MAC address to have been loaded from the EEPROM into RAR0
601 **/
ixgbe_get_mac_addr_generic(struct ixgbe_hw * hw,u8 * mac_addr)602 s32 ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr)
603 {
604 u32 rar_high;
605 u32 rar_low;
606 u16 i;
607
608 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(0));
609 rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(0));
610
611 for (i = 0; i < 4; i++)
612 mac_addr[i] = (u8)(rar_low >> (i*8));
613
614 for (i = 0; i < 2; i++)
615 mac_addr[i+4] = (u8)(rar_high >> (i*8));
616
617 return 0;
618 }
619
ixgbe_convert_bus_width(u16 link_status)620 enum ixgbe_bus_width ixgbe_convert_bus_width(u16 link_status)
621 {
622 switch (link_status & IXGBE_PCI_LINK_WIDTH) {
623 case IXGBE_PCI_LINK_WIDTH_1:
624 return ixgbe_bus_width_pcie_x1;
625 case IXGBE_PCI_LINK_WIDTH_2:
626 return ixgbe_bus_width_pcie_x2;
627 case IXGBE_PCI_LINK_WIDTH_4:
628 return ixgbe_bus_width_pcie_x4;
629 case IXGBE_PCI_LINK_WIDTH_8:
630 return ixgbe_bus_width_pcie_x8;
631 default:
632 return ixgbe_bus_width_unknown;
633 }
634 }
635
ixgbe_convert_bus_speed(u16 link_status)636 enum ixgbe_bus_speed ixgbe_convert_bus_speed(u16 link_status)
637 {
638 switch (link_status & IXGBE_PCI_LINK_SPEED) {
639 case IXGBE_PCI_LINK_SPEED_2500:
640 return ixgbe_bus_speed_2500;
641 case IXGBE_PCI_LINK_SPEED_5000:
642 return ixgbe_bus_speed_5000;
643 case IXGBE_PCI_LINK_SPEED_8000:
644 return ixgbe_bus_speed_8000;
645 default:
646 return ixgbe_bus_speed_unknown;
647 }
648 }
649
650 /**
651 * ixgbe_get_bus_info_generic - Generic set PCI bus info
652 * @hw: pointer to hardware structure
653 *
654 * Sets the PCI bus info (speed, width, type) within the ixgbe_hw structure
655 **/
ixgbe_get_bus_info_generic(struct ixgbe_hw * hw)656 s32 ixgbe_get_bus_info_generic(struct ixgbe_hw *hw)
657 {
658 u16 link_status;
659
660 hw->bus.type = ixgbe_bus_type_pci_express;
661
662 /* Get the negotiated link width and speed from PCI config space */
663 link_status = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_LINK_STATUS);
664
665 hw->bus.width = ixgbe_convert_bus_width(link_status);
666 hw->bus.speed = ixgbe_convert_bus_speed(link_status);
667
668 hw->mac.ops.set_lan_id(hw);
669
670 return 0;
671 }
672
673 /**
674 * ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices
675 * @hw: pointer to the HW structure
676 *
677 * Determines the LAN function id by reading memory-mapped registers
678 * and swaps the port value if requested.
679 **/
ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw * hw)680 void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw)
681 {
682 struct ixgbe_bus_info *bus = &hw->bus;
683 u16 ee_ctrl_4;
684 u32 reg;
685
686 reg = IXGBE_READ_REG(hw, IXGBE_STATUS);
687 bus->func = (reg & IXGBE_STATUS_LAN_ID) >> IXGBE_STATUS_LAN_ID_SHIFT;
688 bus->lan_id = bus->func;
689
690 /* check for a port swap */
691 reg = IXGBE_READ_REG(hw, IXGBE_FACTPS(hw));
692 if (reg & IXGBE_FACTPS_LFS)
693 bus->func ^= 0x1;
694
695 /* Get MAC instance from EEPROM for configuring CS4227 */
696 if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP) {
697 hw->eeprom.ops.read(hw, IXGBE_EEPROM_CTRL_4, &ee_ctrl_4);
698 bus->instance_id = (ee_ctrl_4 & IXGBE_EE_CTRL_4_INST_ID) >>
699 IXGBE_EE_CTRL_4_INST_ID_SHIFT;
700 }
701 }
702
703 /**
704 * ixgbe_stop_adapter_generic - Generic stop Tx/Rx units
705 * @hw: pointer to hardware structure
706 *
707 * Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts,
708 * disables transmit and receive units. The adapter_stopped flag is used by
709 * the shared code and drivers to determine if the adapter is in a stopped
710 * state and should not touch the hardware.
711 **/
ixgbe_stop_adapter_generic(struct ixgbe_hw * hw)712 s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw)
713 {
714 u32 reg_val;
715 u16 i;
716
717 /*
718 * Set the adapter_stopped flag so other driver functions stop touching
719 * the hardware
720 */
721 hw->adapter_stopped = true;
722
723 /* Disable the receive unit */
724 hw->mac.ops.disable_rx(hw);
725
726 /* Clear interrupt mask to stop interrupts from being generated */
727 IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK);
728
729 /* Clear any pending interrupts, flush previous writes */
730 IXGBE_READ_REG(hw, IXGBE_EICR);
731
732 /* Disable the transmit unit. Each queue must be disabled. */
733 for (i = 0; i < hw->mac.max_tx_queues; i++)
734 IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), IXGBE_TXDCTL_SWFLSH);
735
736 /* Disable the receive unit by stopping each queue */
737 for (i = 0; i < hw->mac.max_rx_queues; i++) {
738 reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i));
739 reg_val &= ~IXGBE_RXDCTL_ENABLE;
740 reg_val |= IXGBE_RXDCTL_SWFLSH;
741 IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val);
742 }
743
744 /* flush all queues disables */
745 IXGBE_WRITE_FLUSH(hw);
746 usleep_range(1000, 2000);
747
748 /*
749 * Prevent the PCI-E bus from hanging by disabling PCI-E primary
750 * access and verify no pending requests
751 */
752 return ixgbe_disable_pcie_primary(hw);
753 }
754
755 /**
756 * ixgbe_init_led_link_act_generic - Store the LED index link/activity.
757 * @hw: pointer to hardware structure
758 *
759 * Store the index for the link active LED. This will be used to support
760 * blinking the LED.
761 **/
ixgbe_init_led_link_act_generic(struct ixgbe_hw * hw)762 s32 ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw)
763 {
764 struct ixgbe_mac_info *mac = &hw->mac;
765 u32 led_reg, led_mode;
766 u16 i;
767
768 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
769
770 /* Get LED link active from the LEDCTL register */
771 for (i = 0; i < 4; i++) {
772 led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i);
773
774 if ((led_mode & IXGBE_LED_MODE_MASK_BASE) ==
775 IXGBE_LED_LINK_ACTIVE) {
776 mac->led_link_act = i;
777 return 0;
778 }
779 }
780
781 /* If LEDCTL register does not have the LED link active set, then use
782 * known MAC defaults.
783 */
784 switch (hw->mac.type) {
785 case ixgbe_mac_x550em_a:
786 mac->led_link_act = 0;
787 break;
788 case ixgbe_mac_X550EM_x:
789 mac->led_link_act = 1;
790 break;
791 default:
792 mac->led_link_act = 2;
793 }
794
795 return 0;
796 }
797
798 /**
799 * ixgbe_led_on_generic - Turns on the software controllable LEDs.
800 * @hw: pointer to hardware structure
801 * @index: led number to turn on
802 **/
ixgbe_led_on_generic(struct ixgbe_hw * hw,u32 index)803 s32 ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index)
804 {
805 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
806
807 if (index > 3)
808 return -EINVAL;
809
810 /* To turn on the LED, set mode to ON. */
811 led_reg &= ~IXGBE_LED_MODE_MASK(index);
812 led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index);
813 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
814 IXGBE_WRITE_FLUSH(hw);
815
816 return 0;
817 }
818
819 /**
820 * ixgbe_led_off_generic - Turns off the software controllable LEDs.
821 * @hw: pointer to hardware structure
822 * @index: led number to turn off
823 **/
ixgbe_led_off_generic(struct ixgbe_hw * hw,u32 index)824 s32 ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index)
825 {
826 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
827
828 if (index > 3)
829 return -EINVAL;
830
831 /* To turn off the LED, set mode to OFF. */
832 led_reg &= ~IXGBE_LED_MODE_MASK(index);
833 led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index);
834 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
835 IXGBE_WRITE_FLUSH(hw);
836
837 return 0;
838 }
839
840 /**
841 * ixgbe_init_eeprom_params_generic - Initialize EEPROM params
842 * @hw: pointer to hardware structure
843 *
844 * Initializes the EEPROM parameters ixgbe_eeprom_info within the
845 * ixgbe_hw struct in order to set up EEPROM access.
846 **/
ixgbe_init_eeprom_params_generic(struct ixgbe_hw * hw)847 s32 ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw)
848 {
849 struct ixgbe_eeprom_info *eeprom = &hw->eeprom;
850 u32 eec;
851 u16 eeprom_size;
852
853 if (eeprom->type == ixgbe_eeprom_uninitialized) {
854 eeprom->type = ixgbe_eeprom_none;
855 /* Set default semaphore delay to 10ms which is a well
856 * tested value */
857 eeprom->semaphore_delay = 10;
858 /* Clear EEPROM page size, it will be initialized as needed */
859 eeprom->word_page_size = 0;
860
861 /*
862 * Check for EEPROM present first.
863 * If not present leave as none
864 */
865 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
866 if (eec & IXGBE_EEC_PRES) {
867 eeprom->type = ixgbe_eeprom_spi;
868
869 /*
870 * SPI EEPROM is assumed here. This code would need to
871 * change if a future EEPROM is not SPI.
872 */
873 eeprom_size = (u16)((eec & IXGBE_EEC_SIZE) >>
874 IXGBE_EEC_SIZE_SHIFT);
875 eeprom->word_size = BIT(eeprom_size +
876 IXGBE_EEPROM_WORD_SIZE_SHIFT);
877 }
878
879 if (eec & IXGBE_EEC_ADDR_SIZE)
880 eeprom->address_bits = 16;
881 else
882 eeprom->address_bits = 8;
883 hw_dbg(hw, "Eeprom params: type = %d, size = %d, address bits: %d\n",
884 eeprom->type, eeprom->word_size, eeprom->address_bits);
885 }
886
887 return 0;
888 }
889
890 /**
891 * ixgbe_write_eeprom_buffer_bit_bang_generic - Write EEPROM using bit-bang
892 * @hw: pointer to hardware structure
893 * @offset: offset within the EEPROM to write
894 * @words: number of words
895 * @data: 16 bit word(s) to write to EEPROM
896 *
897 * Reads 16 bit word(s) from EEPROM through bit-bang method
898 **/
ixgbe_write_eeprom_buffer_bit_bang_generic(struct ixgbe_hw * hw,u16 offset,u16 words,u16 * data)899 s32 ixgbe_write_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
900 u16 words, u16 *data)
901 {
902 s32 status;
903 u16 i, count;
904
905 hw->eeprom.ops.init_params(hw);
906
907 if (words == 0 || (offset + words > hw->eeprom.word_size))
908 return -EINVAL;
909
910 /*
911 * The EEPROM page size cannot be queried from the chip. We do lazy
912 * initialization. It is worth to do that when we write large buffer.
913 */
914 if ((hw->eeprom.word_page_size == 0) &&
915 (words > IXGBE_EEPROM_PAGE_SIZE_MAX))
916 ixgbe_detect_eeprom_page_size_generic(hw, offset);
917
918 /*
919 * We cannot hold synchronization semaphores for too long
920 * to avoid other entity starvation. However it is more efficient
921 * to read in bursts than synchronizing access for each word.
922 */
923 for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) {
924 count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ?
925 IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i);
926 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset + i,
927 count, &data[i]);
928
929 if (status != 0)
930 break;
931 }
932
933 return status;
934 }
935
936 /**
937 * ixgbe_write_eeprom_buffer_bit_bang - Writes 16 bit word(s) to EEPROM
938 * @hw: pointer to hardware structure
939 * @offset: offset within the EEPROM to be written to
940 * @words: number of word(s)
941 * @data: 16 bit word(s) to be written to the EEPROM
942 *
943 * If ixgbe_eeprom_update_checksum is not called after this function, the
944 * EEPROM will most likely contain an invalid checksum.
945 **/
ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw * hw,u16 offset,u16 words,u16 * data)946 static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
947 u16 words, u16 *data)
948 {
949 s32 status;
950 u16 word;
951 u16 page_size;
952 u16 i;
953 u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI;
954
955 /* Prepare the EEPROM for writing */
956 status = ixgbe_acquire_eeprom(hw);
957 if (status)
958 return status;
959
960 if (ixgbe_ready_eeprom(hw) != 0) {
961 ixgbe_release_eeprom(hw);
962 return -EIO;
963 }
964
965 for (i = 0; i < words; i++) {
966 ixgbe_standby_eeprom(hw);
967
968 /* Send the WRITE ENABLE command (8 bit opcode) */
969 ixgbe_shift_out_eeprom_bits(hw,
970 IXGBE_EEPROM_WREN_OPCODE_SPI,
971 IXGBE_EEPROM_OPCODE_BITS);
972
973 ixgbe_standby_eeprom(hw);
974
975 /* Some SPI eeproms use the 8th address bit embedded
976 * in the opcode
977 */
978 if ((hw->eeprom.address_bits == 8) &&
979 ((offset + i) >= 128))
980 write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;
981
982 /* Send the Write command (8-bit opcode + addr) */
983 ixgbe_shift_out_eeprom_bits(hw, write_opcode,
984 IXGBE_EEPROM_OPCODE_BITS);
985 ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2),
986 hw->eeprom.address_bits);
987
988 page_size = hw->eeprom.word_page_size;
989
990 /* Send the data in burst via SPI */
991 do {
992 word = data[i];
993 word = (word >> 8) | (word << 8);
994 ixgbe_shift_out_eeprom_bits(hw, word, 16);
995
996 if (page_size == 0)
997 break;
998
999 /* do not wrap around page */
1000 if (((offset + i) & (page_size - 1)) ==
1001 (page_size - 1))
1002 break;
1003 } while (++i < words);
1004
1005 ixgbe_standby_eeprom(hw);
1006 usleep_range(10000, 20000);
1007 }
1008 /* Done with writing - release the EEPROM */
1009 ixgbe_release_eeprom(hw);
1010
1011 return 0;
1012 }
1013
1014 /**
1015 * ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM
1016 * @hw: pointer to hardware structure
1017 * @offset: offset within the EEPROM to be written to
1018 * @data: 16 bit word to be written to the EEPROM
1019 *
1020 * If ixgbe_eeprom_update_checksum is not called after this function, the
1021 * EEPROM will most likely contain an invalid checksum.
1022 **/
ixgbe_write_eeprom_generic(struct ixgbe_hw * hw,u16 offset,u16 data)1023 s32 ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
1024 {
1025 hw->eeprom.ops.init_params(hw);
1026
1027 if (offset >= hw->eeprom.word_size)
1028 return -EINVAL;
1029
1030 return ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1, &data);
1031 }
1032
1033 /**
1034 * ixgbe_read_eeprom_buffer_bit_bang_generic - Read EEPROM using bit-bang
1035 * @hw: pointer to hardware structure
1036 * @offset: offset within the EEPROM to be read
1037 * @words: number of word(s)
1038 * @data: read 16 bit words(s) from EEPROM
1039 *
1040 * Reads 16 bit word(s) from EEPROM through bit-bang method
1041 **/
ixgbe_read_eeprom_buffer_bit_bang_generic(struct ixgbe_hw * hw,u16 offset,u16 words,u16 * data)1042 s32 ixgbe_read_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
1043 u16 words, u16 *data)
1044 {
1045 s32 status;
1046 u16 i, count;
1047
1048 hw->eeprom.ops.init_params(hw);
1049
1050 if (words == 0 || (offset + words > hw->eeprom.word_size))
1051 return -EINVAL;
1052
1053 /*
1054 * We cannot hold synchronization semaphores for too long
1055 * to avoid other entity starvation. However it is more efficient
1056 * to read in bursts than synchronizing access for each word.
1057 */
1058 for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) {
1059 count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ?
1060 IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i);
1061
1062 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset + i,
1063 count, &data[i]);
1064
1065 if (status)
1066 return status;
1067 }
1068
1069 return 0;
1070 }
1071
1072 /**
1073 * ixgbe_read_eeprom_buffer_bit_bang - Read EEPROM using bit-bang
1074 * @hw: pointer to hardware structure
1075 * @offset: offset within the EEPROM to be read
1076 * @words: number of word(s)
1077 * @data: read 16 bit word(s) from EEPROM
1078 *
1079 * Reads 16 bit word(s) from EEPROM through bit-bang method
1080 **/
ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw * hw,u16 offset,u16 words,u16 * data)1081 static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
1082 u16 words, u16 *data)
1083 {
1084 s32 status;
1085 u16 word_in;
1086 u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI;
1087 u16 i;
1088
1089 /* Prepare the EEPROM for reading */
1090 status = ixgbe_acquire_eeprom(hw);
1091 if (status)
1092 return status;
1093
1094 if (ixgbe_ready_eeprom(hw) != 0) {
1095 ixgbe_release_eeprom(hw);
1096 return -EIO;
1097 }
1098
1099 for (i = 0; i < words; i++) {
1100 ixgbe_standby_eeprom(hw);
1101 /* Some SPI eeproms use the 8th address bit embedded
1102 * in the opcode
1103 */
1104 if ((hw->eeprom.address_bits == 8) &&
1105 ((offset + i) >= 128))
1106 read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;
1107
1108 /* Send the READ command (opcode + addr) */
1109 ixgbe_shift_out_eeprom_bits(hw, read_opcode,
1110 IXGBE_EEPROM_OPCODE_BITS);
1111 ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2),
1112 hw->eeprom.address_bits);
1113
1114 /* Read the data. */
1115 word_in = ixgbe_shift_in_eeprom_bits(hw, 16);
1116 data[i] = (word_in >> 8) | (word_in << 8);
1117 }
1118
1119 /* End this read operation */
1120 ixgbe_release_eeprom(hw);
1121
1122 return 0;
1123 }
1124
1125 /**
1126 * ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang
1127 * @hw: pointer to hardware structure
1128 * @offset: offset within the EEPROM to be read
1129 * @data: read 16 bit value from EEPROM
1130 *
1131 * Reads 16 bit value from EEPROM through bit-bang method
1132 **/
ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw * hw,u16 offset,u16 * data)1133 s32 ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
1134 u16 *data)
1135 {
1136 hw->eeprom.ops.init_params(hw);
1137
1138 if (offset >= hw->eeprom.word_size)
1139 return -EINVAL;
1140
1141 return ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
1142 }
1143
1144 /**
1145 * ixgbe_read_eerd_buffer_generic - Read EEPROM word(s) using EERD
1146 * @hw: pointer to hardware structure
1147 * @offset: offset of word in the EEPROM to read
1148 * @words: number of word(s)
1149 * @data: 16 bit word(s) from the EEPROM
1150 *
1151 * Reads a 16 bit word(s) from the EEPROM using the EERD register.
1152 **/
ixgbe_read_eerd_buffer_generic(struct ixgbe_hw * hw,u16 offset,u16 words,u16 * data)1153 s32 ixgbe_read_eerd_buffer_generic(struct ixgbe_hw *hw, u16 offset,
1154 u16 words, u16 *data)
1155 {
1156 u32 eerd;
1157 s32 status;
1158 u32 i;
1159
1160 hw->eeprom.ops.init_params(hw);
1161
1162 if (words == 0 || offset >= hw->eeprom.word_size)
1163 return -EINVAL;
1164
1165 for (i = 0; i < words; i++) {
1166 eerd = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
1167 IXGBE_EEPROM_RW_REG_START;
1168
1169 IXGBE_WRITE_REG(hw, IXGBE_EERD, eerd);
1170 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_READ);
1171
1172 if (status == 0) {
1173 data[i] = (IXGBE_READ_REG(hw, IXGBE_EERD) >>
1174 IXGBE_EEPROM_RW_REG_DATA);
1175 } else {
1176 hw_dbg(hw, "Eeprom read timed out\n");
1177 return status;
1178 }
1179 }
1180
1181 return 0;
1182 }
1183
1184 /**
1185 * ixgbe_detect_eeprom_page_size_generic - Detect EEPROM page size
1186 * @hw: pointer to hardware structure
1187 * @offset: offset within the EEPROM to be used as a scratch pad
1188 *
1189 * Discover EEPROM page size by writing marching data at given offset.
1190 * This function is called only when we are writing a new large buffer
1191 * at given offset so the data would be overwritten anyway.
1192 **/
ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw * hw,u16 offset)1193 static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
1194 u16 offset)
1195 {
1196 u16 data[IXGBE_EEPROM_PAGE_SIZE_MAX];
1197 s32 status;
1198 u16 i;
1199
1200 for (i = 0; i < IXGBE_EEPROM_PAGE_SIZE_MAX; i++)
1201 data[i] = i;
1202
1203 hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX;
1204 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset,
1205 IXGBE_EEPROM_PAGE_SIZE_MAX, data);
1206 hw->eeprom.word_page_size = 0;
1207 if (status)
1208 return status;
1209
1210 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
1211 if (status)
1212 return status;
1213
1214 /*
1215 * When writing in burst more than the actual page size
1216 * EEPROM address wraps around current page.
1217 */
1218 hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX - data[0];
1219
1220 hw_dbg(hw, "Detected EEPROM page size = %d words.\n",
1221 hw->eeprom.word_page_size);
1222 return 0;
1223 }
1224
1225 /**
1226 * ixgbe_read_eerd_generic - Read EEPROM word using EERD
1227 * @hw: pointer to hardware structure
1228 * @offset: offset of word in the EEPROM to read
1229 * @data: word read from the EEPROM
1230 *
1231 * Reads a 16 bit word from the EEPROM using the EERD register.
1232 **/
ixgbe_read_eerd_generic(struct ixgbe_hw * hw,u16 offset,u16 * data)1233 s32 ixgbe_read_eerd_generic(struct ixgbe_hw *hw, u16 offset, u16 *data)
1234 {
1235 return ixgbe_read_eerd_buffer_generic(hw, offset, 1, data);
1236 }
1237
1238 /**
1239 * ixgbe_write_eewr_buffer_generic - Write EEPROM word(s) using EEWR
1240 * @hw: pointer to hardware structure
1241 * @offset: offset of word in the EEPROM to write
1242 * @words: number of words
1243 * @data: word(s) write to the EEPROM
1244 *
1245 * Write a 16 bit word(s) to the EEPROM using the EEWR register.
1246 **/
ixgbe_write_eewr_buffer_generic(struct ixgbe_hw * hw,u16 offset,u16 words,u16 * data)1247 s32 ixgbe_write_eewr_buffer_generic(struct ixgbe_hw *hw, u16 offset,
1248 u16 words, u16 *data)
1249 {
1250 u32 eewr;
1251 s32 status;
1252 u16 i;
1253
1254 hw->eeprom.ops.init_params(hw);
1255
1256 if (words == 0 || offset >= hw->eeprom.word_size)
1257 return -EINVAL;
1258
1259 for (i = 0; i < words; i++) {
1260 eewr = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
1261 (data[i] << IXGBE_EEPROM_RW_REG_DATA) |
1262 IXGBE_EEPROM_RW_REG_START;
1263
1264 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE);
1265 if (status) {
1266 hw_dbg(hw, "Eeprom write EEWR timed out\n");
1267 return status;
1268 }
1269
1270 IXGBE_WRITE_REG(hw, IXGBE_EEWR, eewr);
1271
1272 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE);
1273 if (status) {
1274 hw_dbg(hw, "Eeprom write EEWR timed out\n");
1275 return status;
1276 }
1277 }
1278
1279 return 0;
1280 }
1281
1282 /**
1283 * ixgbe_write_eewr_generic - Write EEPROM word using EEWR
1284 * @hw: pointer to hardware structure
1285 * @offset: offset of word in the EEPROM to write
1286 * @data: word write to the EEPROM
1287 *
1288 * Write a 16 bit word to the EEPROM using the EEWR register.
1289 **/
ixgbe_write_eewr_generic(struct ixgbe_hw * hw,u16 offset,u16 data)1290 s32 ixgbe_write_eewr_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
1291 {
1292 return ixgbe_write_eewr_buffer_generic(hw, offset, 1, &data);
1293 }
1294
1295 /**
1296 * ixgbe_poll_eerd_eewr_done - Poll EERD read or EEWR write status
1297 * @hw: pointer to hardware structure
1298 * @ee_reg: EEPROM flag for polling
1299 *
1300 * Polls the status bit (bit 1) of the EERD or EEWR to determine when the
1301 * read or write is done respectively.
1302 **/
ixgbe_poll_eerd_eewr_done(struct ixgbe_hw * hw,u32 ee_reg)1303 static s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg)
1304 {
1305 u32 i;
1306 u32 reg;
1307
1308 for (i = 0; i < IXGBE_EERD_EEWR_ATTEMPTS; i++) {
1309 if (ee_reg == IXGBE_NVM_POLL_READ)
1310 reg = IXGBE_READ_REG(hw, IXGBE_EERD);
1311 else
1312 reg = IXGBE_READ_REG(hw, IXGBE_EEWR);
1313
1314 if (reg & IXGBE_EEPROM_RW_REG_DONE) {
1315 return 0;
1316 }
1317 udelay(5);
1318 }
1319 return -EIO;
1320 }
1321
1322 /**
1323 * ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang
1324 * @hw: pointer to hardware structure
1325 *
1326 * Prepares EEPROM for access using bit-bang method. This function should
1327 * be called before issuing a command to the EEPROM.
1328 **/
ixgbe_acquire_eeprom(struct ixgbe_hw * hw)1329 static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw)
1330 {
1331 u32 eec;
1332 u32 i;
1333
1334 if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0)
1335 return -EBUSY;
1336
1337 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1338
1339 /* Request EEPROM Access */
1340 eec |= IXGBE_EEC_REQ;
1341 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1342
1343 for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) {
1344 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1345 if (eec & IXGBE_EEC_GNT)
1346 break;
1347 udelay(5);
1348 }
1349
1350 /* Release if grant not acquired */
1351 if (!(eec & IXGBE_EEC_GNT)) {
1352 eec &= ~IXGBE_EEC_REQ;
1353 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1354 hw_dbg(hw, "Could not acquire EEPROM grant\n");
1355
1356 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
1357 return -EIO;
1358 }
1359
1360 /* Setup EEPROM for Read/Write */
1361 /* Clear CS and SK */
1362 eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK);
1363 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1364 IXGBE_WRITE_FLUSH(hw);
1365 udelay(1);
1366 return 0;
1367 }
1368
1369 /**
1370 * ixgbe_get_eeprom_semaphore - Get hardware semaphore
1371 * @hw: pointer to hardware structure
1372 *
1373 * Sets the hardware semaphores so EEPROM access can occur for bit-bang method
1374 **/
ixgbe_get_eeprom_semaphore(struct ixgbe_hw * hw)1375 static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw)
1376 {
1377 u32 timeout = 2000;
1378 u32 i;
1379 u32 swsm;
1380
1381 /* Get SMBI software semaphore between device drivers first */
1382 for (i = 0; i < timeout; i++) {
1383 /*
1384 * If the SMBI bit is 0 when we read it, then the bit will be
1385 * set and we have the semaphore
1386 */
1387 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1388 if (!(swsm & IXGBE_SWSM_SMBI))
1389 break;
1390 usleep_range(50, 100);
1391 }
1392
1393 if (i == timeout) {
1394 hw_dbg(hw, "Driver can't access the Eeprom - SMBI Semaphore not granted.\n");
1395 /* this release is particularly important because our attempts
1396 * above to get the semaphore may have succeeded, and if there
1397 * was a timeout, we should unconditionally clear the semaphore
1398 * bits to free the driver to make progress
1399 */
1400 ixgbe_release_eeprom_semaphore(hw);
1401
1402 usleep_range(50, 100);
1403 /* one last try
1404 * If the SMBI bit is 0 when we read it, then the bit will be
1405 * set and we have the semaphore
1406 */
1407 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1408 if (swsm & IXGBE_SWSM_SMBI) {
1409 hw_dbg(hw, "Software semaphore SMBI between device drivers not granted.\n");
1410 return -EIO;
1411 }
1412 }
1413
1414 /* Now get the semaphore between SW/FW through the SWESMBI bit */
1415 for (i = 0; i < timeout; i++) {
1416 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1417
1418 /* Set the SW EEPROM semaphore bit to request access */
1419 swsm |= IXGBE_SWSM_SWESMBI;
1420 IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
1421
1422 /* If we set the bit successfully then we got the
1423 * semaphore.
1424 */
1425 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1426 if (swsm & IXGBE_SWSM_SWESMBI)
1427 break;
1428
1429 usleep_range(50, 100);
1430 }
1431
1432 /* Release semaphores and return error if SW EEPROM semaphore
1433 * was not granted because we don't have access to the EEPROM
1434 */
1435 if (i >= timeout) {
1436 hw_dbg(hw, "SWESMBI Software EEPROM semaphore not granted.\n");
1437 ixgbe_release_eeprom_semaphore(hw);
1438 return -EIO;
1439 }
1440
1441 return 0;
1442 }
1443
1444 /**
1445 * ixgbe_release_eeprom_semaphore - Release hardware semaphore
1446 * @hw: pointer to hardware structure
1447 *
1448 * This function clears hardware semaphore bits.
1449 **/
ixgbe_release_eeprom_semaphore(struct ixgbe_hw * hw)1450 static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw)
1451 {
1452 u32 swsm;
1453
1454 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
1455
1456 /* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */
1457 swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI);
1458 IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
1459 IXGBE_WRITE_FLUSH(hw);
1460 }
1461
1462 /**
1463 * ixgbe_ready_eeprom - Polls for EEPROM ready
1464 * @hw: pointer to hardware structure
1465 **/
ixgbe_ready_eeprom(struct ixgbe_hw * hw)1466 static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw)
1467 {
1468 u16 i;
1469 u8 spi_stat_reg;
1470
1471 /*
1472 * Read "Status Register" repeatedly until the LSB is cleared. The
1473 * EEPROM will signal that the command has been completed by clearing
1474 * bit 0 of the internal status register. If it's not cleared within
1475 * 5 milliseconds, then error out.
1476 */
1477 for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) {
1478 ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI,
1479 IXGBE_EEPROM_OPCODE_BITS);
1480 spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8);
1481 if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI))
1482 break;
1483
1484 udelay(5);
1485 ixgbe_standby_eeprom(hw);
1486 }
1487
1488 /*
1489 * On some parts, SPI write time could vary from 0-20mSec on 3.3V
1490 * devices (and only 0-5mSec on 5V devices)
1491 */
1492 if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) {
1493 hw_dbg(hw, "SPI EEPROM Status error\n");
1494 return -EIO;
1495 }
1496
1497 return 0;
1498 }
1499
1500 /**
1501 * ixgbe_standby_eeprom - Returns EEPROM to a "standby" state
1502 * @hw: pointer to hardware structure
1503 **/
ixgbe_standby_eeprom(struct ixgbe_hw * hw)1504 static void ixgbe_standby_eeprom(struct ixgbe_hw *hw)
1505 {
1506 u32 eec;
1507
1508 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1509
1510 /* Toggle CS to flush commands */
1511 eec |= IXGBE_EEC_CS;
1512 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1513 IXGBE_WRITE_FLUSH(hw);
1514 udelay(1);
1515 eec &= ~IXGBE_EEC_CS;
1516 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1517 IXGBE_WRITE_FLUSH(hw);
1518 udelay(1);
1519 }
1520
1521 /**
1522 * ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM.
1523 * @hw: pointer to hardware structure
1524 * @data: data to send to the EEPROM
1525 * @count: number of bits to shift out
1526 **/
ixgbe_shift_out_eeprom_bits(struct ixgbe_hw * hw,u16 data,u16 count)1527 static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
1528 u16 count)
1529 {
1530 u32 eec;
1531 u32 mask;
1532 u32 i;
1533
1534 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1535
1536 /*
1537 * Mask is used to shift "count" bits of "data" out to the EEPROM
1538 * one bit at a time. Determine the starting bit based on count
1539 */
1540 mask = BIT(count - 1);
1541
1542 for (i = 0; i < count; i++) {
1543 /*
1544 * A "1" is shifted out to the EEPROM by setting bit "DI" to a
1545 * "1", and then raising and then lowering the clock (the SK
1546 * bit controls the clock input to the EEPROM). A "0" is
1547 * shifted out to the EEPROM by setting "DI" to "0" and then
1548 * raising and then lowering the clock.
1549 */
1550 if (data & mask)
1551 eec |= IXGBE_EEC_DI;
1552 else
1553 eec &= ~IXGBE_EEC_DI;
1554
1555 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1556 IXGBE_WRITE_FLUSH(hw);
1557
1558 udelay(1);
1559
1560 ixgbe_raise_eeprom_clk(hw, &eec);
1561 ixgbe_lower_eeprom_clk(hw, &eec);
1562
1563 /*
1564 * Shift mask to signify next bit of data to shift in to the
1565 * EEPROM
1566 */
1567 mask = mask >> 1;
1568 }
1569
1570 /* We leave the "DI" bit set to "0" when we leave this routine. */
1571 eec &= ~IXGBE_EEC_DI;
1572 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1573 IXGBE_WRITE_FLUSH(hw);
1574 }
1575
1576 /**
1577 * ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM
1578 * @hw: pointer to hardware structure
1579 * @count: number of bits to shift
1580 **/
ixgbe_shift_in_eeprom_bits(struct ixgbe_hw * hw,u16 count)1581 static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
1582 {
1583 u32 eec;
1584 u32 i;
1585 u16 data = 0;
1586
1587 /*
1588 * In order to read a register from the EEPROM, we need to shift
1589 * 'count' bits in from the EEPROM. Bits are "shifted in" by raising
1590 * the clock input to the EEPROM (setting the SK bit), and then reading
1591 * the value of the "DO" bit. During this "shifting in" process the
1592 * "DI" bit should always be clear.
1593 */
1594 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1595
1596 eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI);
1597
1598 for (i = 0; i < count; i++) {
1599 data = data << 1;
1600 ixgbe_raise_eeprom_clk(hw, &eec);
1601
1602 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1603
1604 eec &= ~(IXGBE_EEC_DI);
1605 if (eec & IXGBE_EEC_DO)
1606 data |= 1;
1607
1608 ixgbe_lower_eeprom_clk(hw, &eec);
1609 }
1610
1611 return data;
1612 }
1613
1614 /**
1615 * ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input.
1616 * @hw: pointer to hardware structure
1617 * @eec: EEC register's current value
1618 **/
ixgbe_raise_eeprom_clk(struct ixgbe_hw * hw,u32 * eec)1619 static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
1620 {
1621 /*
1622 * Raise the clock input to the EEPROM
1623 * (setting the SK bit), then delay
1624 */
1625 *eec = *eec | IXGBE_EEC_SK;
1626 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
1627 IXGBE_WRITE_FLUSH(hw);
1628 udelay(1);
1629 }
1630
1631 /**
1632 * ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input.
1633 * @hw: pointer to hardware structure
1634 * @eec: EEC's current value
1635 **/
ixgbe_lower_eeprom_clk(struct ixgbe_hw * hw,u32 * eec)1636 static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
1637 {
1638 /*
1639 * Lower the clock input to the EEPROM (clearing the SK bit), then
1640 * delay
1641 */
1642 *eec = *eec & ~IXGBE_EEC_SK;
1643 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
1644 IXGBE_WRITE_FLUSH(hw);
1645 udelay(1);
1646 }
1647
1648 /**
1649 * ixgbe_release_eeprom - Release EEPROM, release semaphores
1650 * @hw: pointer to hardware structure
1651 **/
ixgbe_release_eeprom(struct ixgbe_hw * hw)1652 static void ixgbe_release_eeprom(struct ixgbe_hw *hw)
1653 {
1654 u32 eec;
1655
1656 eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
1657
1658 eec |= IXGBE_EEC_CS; /* Pull CS high */
1659 eec &= ~IXGBE_EEC_SK; /* Lower SCK */
1660
1661 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1662 IXGBE_WRITE_FLUSH(hw);
1663
1664 udelay(1);
1665
1666 /* Stop requesting EEPROM access */
1667 eec &= ~IXGBE_EEC_REQ;
1668 IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
1669
1670 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
1671
1672 /*
1673 * Delay before attempt to obtain semaphore again to allow FW
1674 * access. semaphore_delay is in ms we need us for usleep_range
1675 */
1676 usleep_range(hw->eeprom.semaphore_delay * 1000,
1677 hw->eeprom.semaphore_delay * 2000);
1678 }
1679
1680 /**
1681 * ixgbe_calc_eeprom_checksum_generic - Calculates and returns the checksum
1682 * @hw: pointer to hardware structure
1683 **/
ixgbe_calc_eeprom_checksum_generic(struct ixgbe_hw * hw)1684 s32 ixgbe_calc_eeprom_checksum_generic(struct ixgbe_hw *hw)
1685 {
1686 u16 i;
1687 u16 j;
1688 u16 checksum = 0;
1689 u16 length = 0;
1690 u16 pointer = 0;
1691 u16 word = 0;
1692
1693 /* Include 0x0-0x3F in the checksum */
1694 for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) {
1695 if (hw->eeprom.ops.read(hw, i, &word)) {
1696 hw_dbg(hw, "EEPROM read failed\n");
1697 break;
1698 }
1699 checksum += word;
1700 }
1701
1702 /* Include all data from pointers except for the fw pointer */
1703 for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) {
1704 if (hw->eeprom.ops.read(hw, i, &pointer)) {
1705 hw_dbg(hw, "EEPROM read failed\n");
1706 return -EIO;
1707 }
1708
1709 /* If the pointer seems invalid */
1710 if (pointer == 0xFFFF || pointer == 0)
1711 continue;
1712
1713 if (hw->eeprom.ops.read(hw, pointer, &length)) {
1714 hw_dbg(hw, "EEPROM read failed\n");
1715 return -EIO;
1716 }
1717
1718 if (length == 0xFFFF || length == 0)
1719 continue;
1720
1721 for (j = pointer + 1; j <= pointer + length; j++) {
1722 if (hw->eeprom.ops.read(hw, j, &word)) {
1723 hw_dbg(hw, "EEPROM read failed\n");
1724 return -EIO;
1725 }
1726 checksum += word;
1727 }
1728 }
1729
1730 checksum = (u16)IXGBE_EEPROM_SUM - checksum;
1731
1732 return (s32)checksum;
1733 }
1734
1735 /**
1736 * ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum
1737 * @hw: pointer to hardware structure
1738 * @checksum_val: calculated checksum
1739 *
1740 * Performs checksum calculation and validates the EEPROM checksum. If the
1741 * caller does not need checksum_val, the value can be NULL.
1742 **/
ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw * hw,u16 * checksum_val)1743 s32 ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw,
1744 u16 *checksum_val)
1745 {
1746 s32 status;
1747 u16 checksum;
1748 u16 read_checksum = 0;
1749
1750 /*
1751 * Read the first word from the EEPROM. If this times out or fails, do
1752 * not continue or we could be in for a very long wait while every
1753 * EEPROM read fails
1754 */
1755 status = hw->eeprom.ops.read(hw, 0, &checksum);
1756 if (status) {
1757 hw_dbg(hw, "EEPROM read failed\n");
1758 return status;
1759 }
1760
1761 status = hw->eeprom.ops.calc_checksum(hw);
1762 if (status < 0)
1763 return status;
1764
1765 checksum = (u16)(status & 0xffff);
1766
1767 status = hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum);
1768 if (status) {
1769 hw_dbg(hw, "EEPROM read failed\n");
1770 return status;
1771 }
1772
1773 /* Verify read checksum from EEPROM is the same as
1774 * calculated checksum
1775 */
1776 if (read_checksum != checksum)
1777 status = -EIO;
1778
1779 /* If the user cares, return the calculated checksum */
1780 if (checksum_val)
1781 *checksum_val = checksum;
1782
1783 return status;
1784 }
1785
1786 /**
1787 * ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum
1788 * @hw: pointer to hardware structure
1789 **/
ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw * hw)1790 s32 ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw)
1791 {
1792 s32 status;
1793 u16 checksum;
1794
1795 /*
1796 * Read the first word from the EEPROM. If this times out or fails, do
1797 * not continue or we could be in for a very long wait while every
1798 * EEPROM read fails
1799 */
1800 status = hw->eeprom.ops.read(hw, 0, &checksum);
1801 if (status) {
1802 hw_dbg(hw, "EEPROM read failed\n");
1803 return status;
1804 }
1805
1806 status = hw->eeprom.ops.calc_checksum(hw);
1807 if (status < 0)
1808 return status;
1809
1810 checksum = (u16)(status & 0xffff);
1811
1812 status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, checksum);
1813
1814 return status;
1815 }
1816
1817 /**
1818 * ixgbe_set_rar_generic - Set Rx address register
1819 * @hw: pointer to hardware structure
1820 * @index: Receive address register to write
1821 * @addr: Address to put into receive address register
1822 * @vmdq: VMDq "set" or "pool" index
1823 * @enable_addr: set flag that address is active
1824 *
1825 * Puts an ethernet address into a receive address register.
1826 **/
ixgbe_set_rar_generic(struct ixgbe_hw * hw,u32 index,u8 * addr,u32 vmdq,u32 enable_addr)1827 s32 ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq,
1828 u32 enable_addr)
1829 {
1830 u32 rar_low, rar_high;
1831 u32 rar_entries = hw->mac.num_rar_entries;
1832
1833 /* Make sure we are using a valid rar index range */
1834 if (index >= rar_entries) {
1835 hw_dbg(hw, "RAR index %d is out of range.\n", index);
1836 return -EINVAL;
1837 }
1838
1839 /* setup VMDq pool selection before this RAR gets enabled */
1840 hw->mac.ops.set_vmdq(hw, index, vmdq);
1841
1842 /*
1843 * HW expects these in little endian so we reverse the byte
1844 * order from network order (big endian) to little endian
1845 */
1846 rar_low = ((u32)addr[0] |
1847 ((u32)addr[1] << 8) |
1848 ((u32)addr[2] << 16) |
1849 ((u32)addr[3] << 24));
1850 /*
1851 * Some parts put the VMDq setting in the extra RAH bits,
1852 * so save everything except the lower 16 bits that hold part
1853 * of the address and the address valid bit.
1854 */
1855 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index));
1856 rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV);
1857 rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8));
1858
1859 if (enable_addr != 0)
1860 rar_high |= IXGBE_RAH_AV;
1861
1862 /* Record lower 32 bits of MAC address and then make
1863 * sure that write is flushed to hardware before writing
1864 * the upper 16 bits and setting the valid bit.
1865 */
1866 IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low);
1867 IXGBE_WRITE_FLUSH(hw);
1868 IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high);
1869
1870 return 0;
1871 }
1872
1873 /**
1874 * ixgbe_clear_rar_generic - Remove Rx address register
1875 * @hw: pointer to hardware structure
1876 * @index: Receive address register to write
1877 *
1878 * Clears an ethernet address from a receive address register.
1879 **/
ixgbe_clear_rar_generic(struct ixgbe_hw * hw,u32 index)1880 s32 ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index)
1881 {
1882 u32 rar_high;
1883 u32 rar_entries = hw->mac.num_rar_entries;
1884
1885 /* Make sure we are using a valid rar index range */
1886 if (index >= rar_entries) {
1887 hw_dbg(hw, "RAR index %d is out of range.\n", index);
1888 return -EINVAL;
1889 }
1890
1891 /*
1892 * Some parts put the VMDq setting in the extra RAH bits,
1893 * so save everything except the lower 16 bits that hold part
1894 * of the address and the address valid bit.
1895 */
1896 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index));
1897 rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV);
1898
1899 /* Clear the address valid bit and upper 16 bits of the address
1900 * before clearing the lower bits. This way we aren't updating
1901 * a live filter.
1902 */
1903 IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high);
1904 IXGBE_WRITE_FLUSH(hw);
1905 IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0);
1906
1907 /* clear VMDq pool/queue selection for this RAR */
1908 hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL);
1909
1910 return 0;
1911 }
1912
1913 /**
1914 * ixgbe_init_rx_addrs_generic - Initializes receive address filters.
1915 * @hw: pointer to hardware structure
1916 *
1917 * Places the MAC address in receive address register 0 and clears the rest
1918 * of the receive address registers. Clears the multicast table. Assumes
1919 * the receiver is in reset when the routine is called.
1920 **/
ixgbe_init_rx_addrs_generic(struct ixgbe_hw * hw)1921 s32 ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw)
1922 {
1923 u32 i;
1924 u32 rar_entries = hw->mac.num_rar_entries;
1925
1926 /*
1927 * If the current mac address is valid, assume it is a software override
1928 * to the permanent address.
1929 * Otherwise, use the permanent address from the eeprom.
1930 */
1931 if (!is_valid_ether_addr(hw->mac.addr)) {
1932 /* Get the MAC address from the RAR0 for later reference */
1933 hw->mac.ops.get_mac_addr(hw, hw->mac.addr);
1934
1935 hw_dbg(hw, " Keeping Current RAR0 Addr =%pM\n", hw->mac.addr);
1936 } else {
1937 /* Setup the receive address. */
1938 hw_dbg(hw, "Overriding MAC Address in RAR[0]\n");
1939 hw_dbg(hw, " New MAC Addr =%pM\n", hw->mac.addr);
1940
1941 hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV);
1942 }
1943
1944 /* clear VMDq pool/queue selection for RAR 0 */
1945 hw->mac.ops.clear_vmdq(hw, 0, IXGBE_CLEAR_VMDQ_ALL);
1946
1947 hw->addr_ctrl.overflow_promisc = 0;
1948
1949 hw->addr_ctrl.rar_used_count = 1;
1950
1951 /* Zero out the other receive addresses. */
1952 hw_dbg(hw, "Clearing RAR[1-%d]\n", rar_entries - 1);
1953 for (i = 1; i < rar_entries; i++) {
1954 IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0);
1955 IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0);
1956 }
1957
1958 /* Clear the MTA */
1959 hw->addr_ctrl.mta_in_use = 0;
1960 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type);
1961
1962 hw_dbg(hw, " Clearing MTA\n");
1963 for (i = 0; i < hw->mac.mcft_size; i++)
1964 IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0);
1965
1966 if (hw->mac.ops.init_uta_tables)
1967 hw->mac.ops.init_uta_tables(hw);
1968
1969 return 0;
1970 }
1971
1972 /**
1973 * ixgbe_mta_vector - Determines bit-vector in multicast table to set
1974 * @hw: pointer to hardware structure
1975 * @mc_addr: the multicast address
1976 *
1977 * Extracts the 12 bits, from a multicast address, to determine which
1978 * bit-vector to set in the multicast table. The hardware uses 12 bits, from
1979 * incoming rx multicast addresses, to determine the bit-vector to check in
1980 * the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set
1981 * by the MO field of the MCSTCTRL. The MO field is set during initialization
1982 * to mc_filter_type.
1983 **/
ixgbe_mta_vector(struct ixgbe_hw * hw,u8 * mc_addr)1984 static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr)
1985 {
1986 u32 vector = 0;
1987
1988 switch (hw->mac.mc_filter_type) {
1989 case 0: /* use bits [47:36] of the address */
1990 vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
1991 break;
1992 case 1: /* use bits [46:35] of the address */
1993 vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5));
1994 break;
1995 case 2: /* use bits [45:34] of the address */
1996 vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
1997 break;
1998 case 3: /* use bits [43:32] of the address */
1999 vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8));
2000 break;
2001 default: /* Invalid mc_filter_type */
2002 hw_dbg(hw, "MC filter type param set incorrectly\n");
2003 break;
2004 }
2005
2006 /* vector can only be 12-bits or boundary will be exceeded */
2007 vector &= 0xFFF;
2008 return vector;
2009 }
2010
2011 /**
2012 * ixgbe_set_mta - Set bit-vector in multicast table
2013 * @hw: pointer to hardware structure
2014 * @mc_addr: Multicast address
2015 *
2016 * Sets the bit-vector in the multicast table.
2017 **/
ixgbe_set_mta(struct ixgbe_hw * hw,u8 * mc_addr)2018 static void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr)
2019 {
2020 u32 vector;
2021 u32 vector_bit;
2022 u32 vector_reg;
2023
2024 hw->addr_ctrl.mta_in_use++;
2025
2026 vector = ixgbe_mta_vector(hw, mc_addr);
2027 hw_dbg(hw, " bit-vector = 0x%03X\n", vector);
2028
2029 /*
2030 * The MTA is a register array of 128 32-bit registers. It is treated
2031 * like an array of 4096 bits. We want to set bit
2032 * BitArray[vector_value]. So we figure out what register the bit is
2033 * in, read it, OR in the new bit, then write back the new value. The
2034 * register is determined by the upper 7 bits of the vector value and
2035 * the bit within that register are determined by the lower 5 bits of
2036 * the value.
2037 */
2038 vector_reg = (vector >> 5) & 0x7F;
2039 vector_bit = vector & 0x1F;
2040 hw->mac.mta_shadow[vector_reg] |= BIT(vector_bit);
2041 }
2042
2043 /**
2044 * ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses
2045 * @hw: pointer to hardware structure
2046 * @netdev: pointer to net device structure
2047 *
2048 * The given list replaces any existing list. Clears the MC addrs from receive
2049 * address registers and the multicast table. Uses unused receive address
2050 * registers for the first multicast addresses, and hashes the rest into the
2051 * multicast table.
2052 **/
ixgbe_update_mc_addr_list_generic(struct ixgbe_hw * hw,struct net_device * netdev)2053 s32 ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw,
2054 struct net_device *netdev)
2055 {
2056 struct netdev_hw_addr *ha;
2057 u32 i;
2058
2059 /*
2060 * Set the new number of MC addresses that we are being requested to
2061 * use.
2062 */
2063 hw->addr_ctrl.num_mc_addrs = netdev_mc_count(netdev);
2064 hw->addr_ctrl.mta_in_use = 0;
2065
2066 /* Clear mta_shadow */
2067 hw_dbg(hw, " Clearing MTA\n");
2068 memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
2069
2070 /* Update mta shadow */
2071 netdev_for_each_mc_addr(ha, netdev) {
2072 hw_dbg(hw, " Adding the multicast addresses:\n");
2073 ixgbe_set_mta(hw, ha->addr);
2074 }
2075
2076 /* Enable mta */
2077 for (i = 0; i < hw->mac.mcft_size; i++)
2078 IXGBE_WRITE_REG_ARRAY(hw, IXGBE_MTA(0), i,
2079 hw->mac.mta_shadow[i]);
2080
2081 if (hw->addr_ctrl.mta_in_use > 0)
2082 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL,
2083 IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type);
2084
2085 hw_dbg(hw, "ixgbe_update_mc_addr_list_generic Complete\n");
2086 return 0;
2087 }
2088
2089 /**
2090 * ixgbe_enable_mc_generic - Enable multicast address in RAR
2091 * @hw: pointer to hardware structure
2092 *
2093 * Enables multicast address in RAR and the use of the multicast hash table.
2094 **/
ixgbe_enable_mc_generic(struct ixgbe_hw * hw)2095 s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw)
2096 {
2097 struct ixgbe_addr_filter_info *a = &hw->addr_ctrl;
2098
2099 if (a->mta_in_use > 0)
2100 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE |
2101 hw->mac.mc_filter_type);
2102
2103 return 0;
2104 }
2105
2106 /**
2107 * ixgbe_disable_mc_generic - Disable multicast address in RAR
2108 * @hw: pointer to hardware structure
2109 *
2110 * Disables multicast address in RAR and the use of the multicast hash table.
2111 **/
ixgbe_disable_mc_generic(struct ixgbe_hw * hw)2112 s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw)
2113 {
2114 struct ixgbe_addr_filter_info *a = &hw->addr_ctrl;
2115
2116 if (a->mta_in_use > 0)
2117 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type);
2118
2119 return 0;
2120 }
2121
2122 /**
2123 * ixgbe_fc_enable_generic - Enable flow control
2124 * @hw: pointer to hardware structure
2125 *
2126 * Enable flow control according to the current settings.
2127 **/
ixgbe_fc_enable_generic(struct ixgbe_hw * hw)2128 s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw)
2129 {
2130 u32 mflcn_reg, fccfg_reg;
2131 u32 reg;
2132 u32 fcrtl, fcrth;
2133 int i;
2134
2135 /* Validate the water mark configuration. */
2136 if (!hw->fc.pause_time)
2137 return -EINVAL;
2138
2139 /* Low water mark of zero causes XOFF floods */
2140 for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
2141 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) &&
2142 hw->fc.high_water[i]) {
2143 if (!hw->fc.low_water[i] ||
2144 hw->fc.low_water[i] >= hw->fc.high_water[i]) {
2145 hw_dbg(hw, "Invalid water mark configuration\n");
2146 return -EINVAL;
2147 }
2148 }
2149 }
2150
2151 /* Negotiate the fc mode to use */
2152 hw->mac.ops.fc_autoneg(hw);
2153
2154 /* Disable any previous flow control settings */
2155 mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN);
2156 mflcn_reg &= ~(IXGBE_MFLCN_RPFCE_MASK | IXGBE_MFLCN_RFCE);
2157
2158 fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG);
2159 fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY);
2160
2161 /*
2162 * The possible values of fc.current_mode are:
2163 * 0: Flow control is completely disabled
2164 * 1: Rx flow control is enabled (we can receive pause frames,
2165 * but not send pause frames).
2166 * 2: Tx flow control is enabled (we can send pause frames but
2167 * we do not support receiving pause frames).
2168 * 3: Both Rx and Tx flow control (symmetric) are enabled.
2169 * other: Invalid.
2170 */
2171 switch (hw->fc.current_mode) {
2172 case ixgbe_fc_none:
2173 /*
2174 * Flow control is disabled by software override or autoneg.
2175 * The code below will actually disable it in the HW.
2176 */
2177 break;
2178 case ixgbe_fc_rx_pause:
2179 /*
2180 * Rx Flow control is enabled and Tx Flow control is
2181 * disabled by software override. Since there really
2182 * isn't a way to advertise that we are capable of RX
2183 * Pause ONLY, we will advertise that we support both
2184 * symmetric and asymmetric Rx PAUSE. Later, we will
2185 * disable the adapter's ability to send PAUSE frames.
2186 */
2187 mflcn_reg |= IXGBE_MFLCN_RFCE;
2188 break;
2189 case ixgbe_fc_tx_pause:
2190 /*
2191 * Tx Flow control is enabled, and Rx Flow control is
2192 * disabled by software override.
2193 */
2194 fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
2195 break;
2196 case ixgbe_fc_full:
2197 /* Flow control (both Rx and Tx) is enabled by SW override. */
2198 mflcn_reg |= IXGBE_MFLCN_RFCE;
2199 fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
2200 break;
2201 default:
2202 hw_dbg(hw, "Flow control param set incorrectly\n");
2203 return -EIO;
2204 }
2205
2206 /* Set 802.3x based flow control settings. */
2207 mflcn_reg |= IXGBE_MFLCN_DPF;
2208 IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg);
2209 IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg);
2210
2211 /* Set up and enable Rx high/low water mark thresholds, enable XON. */
2212 for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
2213 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) &&
2214 hw->fc.high_water[i]) {
2215 fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE;
2216 IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl);
2217 fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN;
2218 } else {
2219 IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0);
2220 /*
2221 * In order to prevent Tx hangs when the internal Tx
2222 * switch is enabled we must set the high water mark
2223 * to the Rx packet buffer size - 24KB. This allows
2224 * the Tx switch to function even under heavy Rx
2225 * workloads.
2226 */
2227 fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576;
2228 }
2229
2230 IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth);
2231 }
2232
2233 /* Configure pause time (2 TCs per register) */
2234 reg = hw->fc.pause_time * 0x00010001U;
2235 for (i = 0; i < (MAX_TRAFFIC_CLASS / 2); i++)
2236 IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg);
2237
2238 IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2);
2239
2240 return 0;
2241 }
2242
2243 /**
2244 * ixgbe_negotiate_fc - Negotiate flow control
2245 * @hw: pointer to hardware structure
2246 * @adv_reg: flow control advertised settings
2247 * @lp_reg: link partner's flow control settings
2248 * @adv_sym: symmetric pause bit in advertisement
2249 * @adv_asm: asymmetric pause bit in advertisement
2250 * @lp_sym: symmetric pause bit in link partner advertisement
2251 * @lp_asm: asymmetric pause bit in link partner advertisement
2252 *
2253 * Find the intersection between advertised settings and link partner's
2254 * advertised settings
2255 **/
ixgbe_negotiate_fc(struct ixgbe_hw * hw,u32 adv_reg,u32 lp_reg,u32 adv_sym,u32 adv_asm,u32 lp_sym,u32 lp_asm)2256 s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
2257 u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
2258 {
2259 if ((!(adv_reg)) || (!(lp_reg)))
2260 return -EINVAL;
2261
2262 if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
2263 /*
2264 * Now we need to check if the user selected Rx ONLY
2265 * of pause frames. In this case, we had to advertise
2266 * FULL flow control because we could not advertise RX
2267 * ONLY. Hence, we must now check to see if we need to
2268 * turn OFF the TRANSMISSION of PAUSE frames.
2269 */
2270 if (hw->fc.requested_mode == ixgbe_fc_full) {
2271 hw->fc.current_mode = ixgbe_fc_full;
2272 hw_dbg(hw, "Flow Control = FULL.\n");
2273 } else {
2274 hw->fc.current_mode = ixgbe_fc_rx_pause;
2275 hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
2276 }
2277 } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
2278 (lp_reg & lp_sym) && (lp_reg & lp_asm)) {
2279 hw->fc.current_mode = ixgbe_fc_tx_pause;
2280 hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
2281 } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
2282 !(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
2283 hw->fc.current_mode = ixgbe_fc_rx_pause;
2284 hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
2285 } else {
2286 hw->fc.current_mode = ixgbe_fc_none;
2287 hw_dbg(hw, "Flow Control = NONE.\n");
2288 }
2289 return 0;
2290 }
2291
2292 /**
2293 * ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber
2294 * @hw: pointer to hardware structure
2295 *
2296 * Enable flow control according on 1 gig fiber.
2297 **/
ixgbe_fc_autoneg_fiber(struct ixgbe_hw * hw)2298 static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw)
2299 {
2300 u32 pcs_anadv_reg, pcs_lpab_reg, linkstat;
2301 s32 ret_val;
2302
2303 /*
2304 * On multispeed fiber at 1g, bail out if
2305 * - link is up but AN did not complete, or if
2306 * - link is up and AN completed but timed out
2307 */
2308
2309 linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
2310 if ((!!(linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
2311 (!!(linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1))
2312 return -EIO;
2313
2314 pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
2315 pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
2316
2317 ret_val = ixgbe_negotiate_fc(hw, pcs_anadv_reg,
2318 pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE,
2319 IXGBE_PCS1GANA_ASM_PAUSE,
2320 IXGBE_PCS1GANA_SYM_PAUSE,
2321 IXGBE_PCS1GANA_ASM_PAUSE);
2322
2323 return ret_val;
2324 }
2325
2326 /**
2327 * ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37
2328 * @hw: pointer to hardware structure
2329 *
2330 * Enable flow control according to IEEE clause 37.
2331 **/
ixgbe_fc_autoneg_backplane(struct ixgbe_hw * hw)2332 static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw)
2333 {
2334 u32 links2, anlp1_reg, autoc_reg, links;
2335 s32 ret_val;
2336
2337 /*
2338 * On backplane, bail out if
2339 * - backplane autoneg was not completed, or if
2340 * - we are 82599 and link partner is not AN enabled
2341 */
2342 links = IXGBE_READ_REG(hw, IXGBE_LINKS);
2343 if ((links & IXGBE_LINKS_KX_AN_COMP) == 0)
2344 return -EIO;
2345
2346 if (hw->mac.type == ixgbe_mac_82599EB) {
2347 links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
2348 if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0)
2349 return -EIO;
2350 }
2351 /*
2352 * Read the 10g AN autoc and LP ability registers and resolve
2353 * local flow control settings accordingly
2354 */
2355 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
2356 anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
2357
2358 ret_val = ixgbe_negotiate_fc(hw, autoc_reg,
2359 anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE,
2360 IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE);
2361
2362 return ret_val;
2363 }
2364
2365 /**
2366 * ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37
2367 * @hw: pointer to hardware structure
2368 *
2369 * Enable flow control according to IEEE clause 37.
2370 **/
ixgbe_fc_autoneg_copper(struct ixgbe_hw * hw)2371 static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw)
2372 {
2373 u16 technology_ability_reg = 0;
2374 u16 lp_technology_ability_reg = 0;
2375
2376 hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
2377 MDIO_MMD_AN,
2378 &technology_ability_reg);
2379 hw->phy.ops.read_reg(hw, MDIO_AN_LPA,
2380 MDIO_MMD_AN,
2381 &lp_technology_ability_reg);
2382
2383 return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg,
2384 (u32)lp_technology_ability_reg,
2385 IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE,
2386 IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE);
2387 }
2388
2389 /**
2390 * ixgbe_fc_autoneg - Configure flow control
2391 * @hw: pointer to hardware structure
2392 *
2393 * Compares our advertised flow control capabilities to those advertised by
2394 * our link partner, and determines the proper flow control mode to use.
2395 **/
ixgbe_fc_autoneg(struct ixgbe_hw * hw)2396 void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
2397 {
2398 ixgbe_link_speed speed;
2399 s32 ret_val = -EIO;
2400 bool link_up;
2401
2402 /*
2403 * AN should have completed when the cable was plugged in.
2404 * Look for reasons to bail out. Bail out if:
2405 * - FC autoneg is disabled, or if
2406 * - link is not up.
2407 *
2408 * Since we're being called from an LSC, link is already known to be up.
2409 * So use link_up_wait_to_complete=false.
2410 */
2411 if (hw->fc.disable_fc_autoneg)
2412 goto out;
2413
2414 hw->mac.ops.check_link(hw, &speed, &link_up, false);
2415 if (!link_up)
2416 goto out;
2417
2418 switch (hw->phy.media_type) {
2419 /* Autoneg flow control on fiber adapters */
2420 case ixgbe_media_type_fiber:
2421 if (speed == IXGBE_LINK_SPEED_1GB_FULL)
2422 ret_val = ixgbe_fc_autoneg_fiber(hw);
2423 break;
2424
2425 /* Autoneg flow control on backplane adapters */
2426 case ixgbe_media_type_backplane:
2427 ret_val = ixgbe_fc_autoneg_backplane(hw);
2428 break;
2429
2430 /* Autoneg flow control on copper adapters */
2431 case ixgbe_media_type_copper:
2432 if (ixgbe_device_supports_autoneg_fc(hw))
2433 ret_val = ixgbe_fc_autoneg_copper(hw);
2434 break;
2435
2436 default:
2437 break;
2438 }
2439
2440 out:
2441 if (ret_val == 0) {
2442 hw->fc.fc_was_autonegged = true;
2443 } else {
2444 hw->fc.fc_was_autonegged = false;
2445 hw->fc.current_mode = hw->fc.requested_mode;
2446 }
2447 }
2448
2449 /**
2450 * ixgbe_pcie_timeout_poll - Return number of times to poll for completion
2451 * @hw: pointer to hardware structure
2452 *
2453 * System-wide timeout range is encoded in PCIe Device Control2 register.
2454 *
2455 * Add 10% to specified maximum and return the number of times to poll for
2456 * completion timeout, in units of 100 microsec. Never return less than
2457 * 800 = 80 millisec.
2458 **/
ixgbe_pcie_timeout_poll(struct ixgbe_hw * hw)2459 static u32 ixgbe_pcie_timeout_poll(struct ixgbe_hw *hw)
2460 {
2461 s16 devctl2;
2462 u32 pollcnt;
2463
2464 devctl2 = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_CONTROL2);
2465 devctl2 &= IXGBE_PCIDEVCTRL2_TIMEO_MASK;
2466
2467 switch (devctl2) {
2468 case IXGBE_PCIDEVCTRL2_65_130ms:
2469 pollcnt = 1300; /* 130 millisec */
2470 break;
2471 case IXGBE_PCIDEVCTRL2_260_520ms:
2472 pollcnt = 5200; /* 520 millisec */
2473 break;
2474 case IXGBE_PCIDEVCTRL2_1_2s:
2475 pollcnt = 20000; /* 2 sec */
2476 break;
2477 case IXGBE_PCIDEVCTRL2_4_8s:
2478 pollcnt = 80000; /* 8 sec */
2479 break;
2480 case IXGBE_PCIDEVCTRL2_17_34s:
2481 pollcnt = 34000; /* 34 sec */
2482 break;
2483 case IXGBE_PCIDEVCTRL2_50_100us: /* 100 microsecs */
2484 case IXGBE_PCIDEVCTRL2_1_2ms: /* 2 millisecs */
2485 case IXGBE_PCIDEVCTRL2_16_32ms: /* 32 millisec */
2486 case IXGBE_PCIDEVCTRL2_16_32ms_def: /* 32 millisec default */
2487 default:
2488 pollcnt = 800; /* 80 millisec minimum */
2489 break;
2490 }
2491
2492 /* add 10% to spec maximum */
2493 return (pollcnt * 11) / 10;
2494 }
2495
2496 /**
2497 * ixgbe_disable_pcie_primary - Disable PCI-express primary access
2498 * @hw: pointer to hardware structure
2499 *
2500 * Disables PCI-Express primary access and verifies there are no pending
2501 * requests. -EALREADY is returned if primary disable
2502 * bit hasn't caused the primary requests to be disabled, else 0
2503 * is returned signifying primary requests disabled.
2504 **/
ixgbe_disable_pcie_primary(struct ixgbe_hw * hw)2505 static s32 ixgbe_disable_pcie_primary(struct ixgbe_hw *hw)
2506 {
2507 u32 i, poll;
2508 u16 value;
2509
2510 /* Always set this bit to ensure any future transactions are blocked */
2511 IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS);
2512
2513 /* Poll for bit to read as set */
2514 for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
2515 if (IXGBE_READ_REG(hw, IXGBE_CTRL) & IXGBE_CTRL_GIO_DIS)
2516 break;
2517 usleep_range(100, 120);
2518 }
2519 if (i >= IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT) {
2520 hw_dbg(hw, "GIO disable did not set - requesting resets\n");
2521 goto gio_disable_fail;
2522 }
2523
2524 /* Exit if primary requests are blocked */
2525 if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO) ||
2526 ixgbe_removed(hw->hw_addr))
2527 return 0;
2528
2529 /* Poll for primary request bit to clear */
2530 for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
2531 udelay(100);
2532 if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO))
2533 return 0;
2534 }
2535
2536 /*
2537 * Two consecutive resets are required via CTRL.RST per datasheet
2538 * 5.2.5.3.2 Primary Disable. We set a flag to inform the reset routine
2539 * of this need. The first reset prevents new primary requests from
2540 * being issued by our device. We then must wait 1usec or more for any
2541 * remaining completions from the PCIe bus to trickle in, and then reset
2542 * again to clear out any effects they may have had on our device.
2543 */
2544 hw_dbg(hw, "GIO Primary Disable bit didn't clear - requesting resets\n");
2545 gio_disable_fail:
2546 hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
2547
2548 if (hw->mac.type >= ixgbe_mac_X550)
2549 return 0;
2550
2551 /*
2552 * Before proceeding, make sure that the PCIe block does not have
2553 * transactions pending.
2554 */
2555 poll = ixgbe_pcie_timeout_poll(hw);
2556 for (i = 0; i < poll; i++) {
2557 udelay(100);
2558 value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS);
2559 if (ixgbe_removed(hw->hw_addr))
2560 return 0;
2561 if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
2562 return 0;
2563 }
2564
2565 hw_dbg(hw, "PCIe transaction pending bit also did not clear.\n");
2566 return -EALREADY;
2567 }
2568
2569 /**
2570 * ixgbe_acquire_swfw_sync - Acquire SWFW semaphore
2571 * @hw: pointer to hardware structure
2572 * @mask: Mask to specify which semaphore to acquire
2573 *
2574 * Acquires the SWFW semaphore through the GSSR register for the specified
2575 * function (CSR, PHY0, PHY1, EEPROM, Flash)
2576 **/
ixgbe_acquire_swfw_sync(struct ixgbe_hw * hw,u32 mask)2577 s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u32 mask)
2578 {
2579 u32 gssr = 0;
2580 u32 swmask = mask;
2581 u32 fwmask = mask << 5;
2582 u32 timeout = 200;
2583 u32 i;
2584
2585 for (i = 0; i < timeout; i++) {
2586 /*
2587 * SW NVM semaphore bit is used for access to all
2588 * SW_FW_SYNC bits (not just NVM)
2589 */
2590 if (ixgbe_get_eeprom_semaphore(hw))
2591 return -EBUSY;
2592
2593 gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
2594 if (!(gssr & (fwmask | swmask))) {
2595 gssr |= swmask;
2596 IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr);
2597 ixgbe_release_eeprom_semaphore(hw);
2598 return 0;
2599 } else {
2600 /* Resource is currently in use by FW or SW */
2601 ixgbe_release_eeprom_semaphore(hw);
2602 usleep_range(5000, 10000);
2603 }
2604 }
2605
2606 /* If time expired clear the bits holding the lock and retry */
2607 if (gssr & (fwmask | swmask))
2608 ixgbe_release_swfw_sync(hw, gssr & (fwmask | swmask));
2609
2610 usleep_range(5000, 10000);
2611 return -EBUSY;
2612 }
2613
2614 /**
2615 * ixgbe_release_swfw_sync - Release SWFW semaphore
2616 * @hw: pointer to hardware structure
2617 * @mask: Mask to specify which semaphore to release
2618 *
2619 * Releases the SWFW semaphore through the GSSR register for the specified
2620 * function (CSR, PHY0, PHY1, EEPROM, Flash)
2621 **/
ixgbe_release_swfw_sync(struct ixgbe_hw * hw,u32 mask)2622 void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u32 mask)
2623 {
2624 u32 gssr;
2625 u32 swmask = mask;
2626
2627 ixgbe_get_eeprom_semaphore(hw);
2628
2629 gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
2630 gssr &= ~swmask;
2631 IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr);
2632
2633 ixgbe_release_eeprom_semaphore(hw);
2634 }
2635
2636 /**
2637 * prot_autoc_read_generic - Hides MAC differences needed for AUTOC read
2638 * @hw: pointer to hardware structure
2639 * @reg_val: Value we read from AUTOC
2640 * @locked: bool to indicate whether the SW/FW lock should be taken. Never
2641 * true in this the generic case.
2642 *
2643 * The default case requires no protection so just to the register read.
2644 **/
prot_autoc_read_generic(struct ixgbe_hw * hw,bool * locked,u32 * reg_val)2645 s32 prot_autoc_read_generic(struct ixgbe_hw *hw, bool *locked, u32 *reg_val)
2646 {
2647 *locked = false;
2648 *reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC);
2649 return 0;
2650 }
2651
2652 /**
2653 * prot_autoc_write_generic - Hides MAC differences needed for AUTOC write
2654 * @hw: pointer to hardware structure
2655 * @reg_val: value to write to AUTOC
2656 * @locked: bool to indicate whether the SW/FW lock was already taken by
2657 * previous read.
2658 **/
prot_autoc_write_generic(struct ixgbe_hw * hw,u32 reg_val,bool locked)2659 s32 prot_autoc_write_generic(struct ixgbe_hw *hw, u32 reg_val, bool locked)
2660 {
2661 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_val);
2662 return 0;
2663 }
2664
2665 /**
2666 * ixgbe_disable_rx_buff_generic - Stops the receive data path
2667 * @hw: pointer to hardware structure
2668 *
2669 * Stops the receive data path and waits for the HW to internally
2670 * empty the Rx security block.
2671 **/
ixgbe_disable_rx_buff_generic(struct ixgbe_hw * hw)2672 s32 ixgbe_disable_rx_buff_generic(struct ixgbe_hw *hw)
2673 {
2674 #define IXGBE_MAX_SECRX_POLL 40
2675 int i;
2676 int secrxreg;
2677
2678 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
2679 secrxreg |= IXGBE_SECRXCTRL_RX_DIS;
2680 IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
2681 for (i = 0; i < IXGBE_MAX_SECRX_POLL; i++) {
2682 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT);
2683 if (secrxreg & IXGBE_SECRXSTAT_SECRX_RDY)
2684 break;
2685 else
2686 /* Use interrupt-safe sleep just in case */
2687 udelay(1000);
2688 }
2689
2690 /* For informational purposes only */
2691 if (i >= IXGBE_MAX_SECRX_POLL)
2692 hw_dbg(hw, "Rx unit being enabled before security path fully disabled. Continuing with init.\n");
2693
2694 return 0;
2695
2696 }
2697
2698 /**
2699 * ixgbe_enable_rx_buff_generic - Enables the receive data path
2700 * @hw: pointer to hardware structure
2701 *
2702 * Enables the receive data path
2703 **/
ixgbe_enable_rx_buff_generic(struct ixgbe_hw * hw)2704 s32 ixgbe_enable_rx_buff_generic(struct ixgbe_hw *hw)
2705 {
2706 u32 secrxreg;
2707
2708 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
2709 secrxreg &= ~IXGBE_SECRXCTRL_RX_DIS;
2710 IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
2711 IXGBE_WRITE_FLUSH(hw);
2712
2713 return 0;
2714 }
2715
2716 /**
2717 * ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit
2718 * @hw: pointer to hardware structure
2719 * @regval: register value to write to RXCTRL
2720 *
2721 * Enables the Rx DMA unit
2722 **/
ixgbe_enable_rx_dma_generic(struct ixgbe_hw * hw,u32 regval)2723 s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval)
2724 {
2725 if (regval & IXGBE_RXCTRL_RXEN)
2726 hw->mac.ops.enable_rx(hw);
2727 else
2728 hw->mac.ops.disable_rx(hw);
2729
2730 return 0;
2731 }
2732
2733 /**
2734 * ixgbe_blink_led_start_generic - Blink LED based on index.
2735 * @hw: pointer to hardware structure
2736 * @index: led number to blink
2737 **/
ixgbe_blink_led_start_generic(struct ixgbe_hw * hw,u32 index)2738 s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index)
2739 {
2740 ixgbe_link_speed speed = 0;
2741 bool link_up = false;
2742 u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
2743 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
2744 bool locked = false;
2745 s32 ret_val;
2746
2747 if (index > 3)
2748 return -EINVAL;
2749
2750 /*
2751 * Link must be up to auto-blink the LEDs;
2752 * Force it if link is down.
2753 */
2754 hw->mac.ops.check_link(hw, &speed, &link_up, false);
2755
2756 if (!link_up) {
2757 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
2758 if (ret_val)
2759 return ret_val;
2760
2761 autoc_reg |= IXGBE_AUTOC_AN_RESTART;
2762 autoc_reg |= IXGBE_AUTOC_FLU;
2763
2764 ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked);
2765 if (ret_val)
2766 return ret_val;
2767
2768 IXGBE_WRITE_FLUSH(hw);
2769
2770 usleep_range(10000, 20000);
2771 }
2772
2773 led_reg &= ~IXGBE_LED_MODE_MASK(index);
2774 led_reg |= IXGBE_LED_BLINK(index);
2775 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
2776 IXGBE_WRITE_FLUSH(hw);
2777
2778 return 0;
2779 }
2780
2781 /**
2782 * ixgbe_blink_led_stop_generic - Stop blinking LED based on index.
2783 * @hw: pointer to hardware structure
2784 * @index: led number to stop blinking
2785 **/
ixgbe_blink_led_stop_generic(struct ixgbe_hw * hw,u32 index)2786 s32 ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index)
2787 {
2788 u32 autoc_reg = 0;
2789 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
2790 bool locked = false;
2791 s32 ret_val;
2792
2793 if (index > 3)
2794 return -EINVAL;
2795
2796 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
2797 if (ret_val)
2798 return ret_val;
2799
2800 autoc_reg &= ~IXGBE_AUTOC_FLU;
2801 autoc_reg |= IXGBE_AUTOC_AN_RESTART;
2802
2803 ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked);
2804 if (ret_val)
2805 return ret_val;
2806
2807 led_reg &= ~IXGBE_LED_MODE_MASK(index);
2808 led_reg &= ~IXGBE_LED_BLINK(index);
2809 led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index);
2810 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
2811 IXGBE_WRITE_FLUSH(hw);
2812
2813 return 0;
2814 }
2815
2816 /**
2817 * ixgbe_get_san_mac_addr_offset - Get SAN MAC address offset from the EEPROM
2818 * @hw: pointer to hardware structure
2819 * @san_mac_offset: SAN MAC address offset
2820 *
2821 * This function will read the EEPROM location for the SAN MAC address
2822 * pointer, and returns the value at that location. This is used in both
2823 * get and set mac_addr routines.
2824 **/
ixgbe_get_san_mac_addr_offset(struct ixgbe_hw * hw,u16 * san_mac_offset)2825 static s32 ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw,
2826 u16 *san_mac_offset)
2827 {
2828 s32 ret_val;
2829
2830 /*
2831 * First read the EEPROM pointer to see if the MAC addresses are
2832 * available.
2833 */
2834 ret_val = hw->eeprom.ops.read(hw, IXGBE_SAN_MAC_ADDR_PTR,
2835 san_mac_offset);
2836 if (ret_val)
2837 hw_err(hw, "eeprom read at offset %d failed\n",
2838 IXGBE_SAN_MAC_ADDR_PTR);
2839
2840 return ret_val;
2841 }
2842
2843 /**
2844 * ixgbe_get_san_mac_addr_generic - SAN MAC address retrieval from the EEPROM
2845 * @hw: pointer to hardware structure
2846 * @san_mac_addr: SAN MAC address
2847 *
2848 * Reads the SAN MAC address from the EEPROM, if it's available. This is
2849 * per-port, so set_lan_id() must be called before reading the addresses.
2850 * set_lan_id() is called by identify_sfp(), but this cannot be relied
2851 * upon for non-SFP connections, so we must call it here.
2852 **/
ixgbe_get_san_mac_addr_generic(struct ixgbe_hw * hw,u8 * san_mac_addr)2853 s32 ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr)
2854 {
2855 u16 san_mac_data, san_mac_offset;
2856 u8 i;
2857 s32 ret_val;
2858
2859 /*
2860 * First read the EEPROM pointer to see if the MAC addresses are
2861 * available. If they're not, no point in calling set_lan_id() here.
2862 */
2863 ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset);
2864 if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF)
2865
2866 goto san_mac_addr_clr;
2867
2868 /* make sure we know which port we need to program */
2869 hw->mac.ops.set_lan_id(hw);
2870 /* apply the port offset to the address offset */
2871 (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) :
2872 (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET);
2873 for (i = 0; i < 3; i++) {
2874 ret_val = hw->eeprom.ops.read(hw, san_mac_offset,
2875 &san_mac_data);
2876 if (ret_val) {
2877 hw_err(hw, "eeprom read at offset %d failed\n",
2878 san_mac_offset);
2879 goto san_mac_addr_clr;
2880 }
2881 san_mac_addr[i * 2] = (u8)(san_mac_data);
2882 san_mac_addr[i * 2 + 1] = (u8)(san_mac_data >> 8);
2883 san_mac_offset++;
2884 }
2885 return 0;
2886
2887 san_mac_addr_clr:
2888 /* No addresses available in this EEPROM. It's not necessarily an
2889 * error though, so just wipe the local address and return.
2890 */
2891 for (i = 0; i < 6; i++)
2892 san_mac_addr[i] = 0xFF;
2893 return ret_val;
2894 }
2895
2896 /**
2897 * ixgbe_get_pcie_msix_count_generic - Gets MSI-X vector count
2898 * @hw: pointer to hardware structure
2899 *
2900 * Read PCIe configuration space, and get the MSI-X vector count from
2901 * the capabilities table.
2902 **/
ixgbe_get_pcie_msix_count_generic(struct ixgbe_hw * hw)2903 u16 ixgbe_get_pcie_msix_count_generic(struct ixgbe_hw *hw)
2904 {
2905 u16 msix_count;
2906 u16 max_msix_count;
2907 u16 pcie_offset;
2908
2909 switch (hw->mac.type) {
2910 case ixgbe_mac_82598EB:
2911 pcie_offset = IXGBE_PCIE_MSIX_82598_CAPS;
2912 max_msix_count = IXGBE_MAX_MSIX_VECTORS_82598;
2913 break;
2914 case ixgbe_mac_82599EB:
2915 case ixgbe_mac_X540:
2916 case ixgbe_mac_X550:
2917 case ixgbe_mac_X550EM_x:
2918 case ixgbe_mac_x550em_a:
2919 pcie_offset = IXGBE_PCIE_MSIX_82599_CAPS;
2920 max_msix_count = IXGBE_MAX_MSIX_VECTORS_82599;
2921 break;
2922 default:
2923 return 1;
2924 }
2925
2926 msix_count = ixgbe_read_pci_cfg_word(hw, pcie_offset);
2927 if (ixgbe_removed(hw->hw_addr))
2928 msix_count = 0;
2929 msix_count &= IXGBE_PCIE_MSIX_TBL_SZ_MASK;
2930
2931 /* MSI-X count is zero-based in HW */
2932 msix_count++;
2933
2934 if (msix_count > max_msix_count)
2935 msix_count = max_msix_count;
2936
2937 return msix_count;
2938 }
2939
2940 /**
2941 * ixgbe_clear_vmdq_generic - Disassociate a VMDq pool index from a rx address
2942 * @hw: pointer to hardware struct
2943 * @rar: receive address register index to disassociate
2944 * @vmdq: VMDq pool index to remove from the rar
2945 **/
ixgbe_clear_vmdq_generic(struct ixgbe_hw * hw,u32 rar,u32 vmdq)2946 s32 ixgbe_clear_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
2947 {
2948 u32 mpsar_lo, mpsar_hi;
2949 u32 rar_entries = hw->mac.num_rar_entries;
2950
2951 /* Make sure we are using a valid rar index range */
2952 if (rar >= rar_entries) {
2953 hw_dbg(hw, "RAR index %d is out of range.\n", rar);
2954 return -EINVAL;
2955 }
2956
2957 mpsar_lo = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
2958 mpsar_hi = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar));
2959
2960 if (ixgbe_removed(hw->hw_addr))
2961 return 0;
2962
2963 if (!mpsar_lo && !mpsar_hi)
2964 return 0;
2965
2966 if (vmdq == IXGBE_CLEAR_VMDQ_ALL) {
2967 if (mpsar_lo) {
2968 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0);
2969 mpsar_lo = 0;
2970 }
2971 if (mpsar_hi) {
2972 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0);
2973 mpsar_hi = 0;
2974 }
2975 } else if (vmdq < 32) {
2976 mpsar_lo &= ~BIT(vmdq);
2977 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar_lo);
2978 } else {
2979 mpsar_hi &= ~BIT(vmdq - 32);
2980 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar_hi);
2981 }
2982
2983 /* was that the last pool using this rar? */
2984 if (mpsar_lo == 0 && mpsar_hi == 0 &&
2985 rar != 0 && rar != hw->mac.san_mac_rar_index)
2986 hw->mac.ops.clear_rar(hw, rar);
2987
2988 return 0;
2989 }
2990
2991 /**
2992 * ixgbe_set_vmdq_generic - Associate a VMDq pool index with a rx address
2993 * @hw: pointer to hardware struct
2994 * @rar: receive address register index to associate with a VMDq index
2995 * @vmdq: VMDq pool index
2996 **/
ixgbe_set_vmdq_generic(struct ixgbe_hw * hw,u32 rar,u32 vmdq)2997 s32 ixgbe_set_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
2998 {
2999 u32 mpsar;
3000 u32 rar_entries = hw->mac.num_rar_entries;
3001
3002 /* Make sure we are using a valid rar index range */
3003 if (rar >= rar_entries) {
3004 hw_dbg(hw, "RAR index %d is out of range.\n", rar);
3005 return -EINVAL;
3006 }
3007
3008 if (vmdq < 32) {
3009 mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
3010 mpsar |= BIT(vmdq);
3011 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar);
3012 } else {
3013 mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar));
3014 mpsar |= BIT(vmdq - 32);
3015 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar);
3016 }
3017 return 0;
3018 }
3019
3020 /**
3021 * ixgbe_set_vmdq_san_mac_generic - Associate VMDq pool index with a rx address
3022 * @hw: pointer to hardware struct
3023 * @vmdq: VMDq pool index
3024 *
3025 * This function should only be involved in the IOV mode.
3026 * In IOV mode, Default pool is next pool after the number of
3027 * VFs advertized and not 0.
3028 * MPSAR table needs to be updated for SAN_MAC RAR [hw->mac.san_mac_rar_index]
3029 **/
ixgbe_set_vmdq_san_mac_generic(struct ixgbe_hw * hw,u32 vmdq)3030 s32 ixgbe_set_vmdq_san_mac_generic(struct ixgbe_hw *hw, u32 vmdq)
3031 {
3032 u32 rar = hw->mac.san_mac_rar_index;
3033
3034 if (vmdq < 32) {
3035 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), BIT(vmdq));
3036 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0);
3037 } else {
3038 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0);
3039 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), BIT(vmdq - 32));
3040 }
3041
3042 return 0;
3043 }
3044
3045 /**
3046 * ixgbe_init_uta_tables_generic - Initialize the Unicast Table Array
3047 * @hw: pointer to hardware structure
3048 **/
ixgbe_init_uta_tables_generic(struct ixgbe_hw * hw)3049 s32 ixgbe_init_uta_tables_generic(struct ixgbe_hw *hw)
3050 {
3051 int i;
3052
3053 for (i = 0; i < 128; i++)
3054 IXGBE_WRITE_REG(hw, IXGBE_UTA(i), 0);
3055
3056 return 0;
3057 }
3058
3059 /**
3060 * ixgbe_find_vlvf_slot - find the vlanid or the first empty slot
3061 * @hw: pointer to hardware structure
3062 * @vlan: VLAN id to write to VLAN filter
3063 * @vlvf_bypass: true to find vlanid only, false returns first empty slot if
3064 * vlanid not found
3065 *
3066 * return the VLVF index where this VLAN id should be placed
3067 *
3068 **/
ixgbe_find_vlvf_slot(struct ixgbe_hw * hw,u32 vlan,bool vlvf_bypass)3069 static s32 ixgbe_find_vlvf_slot(struct ixgbe_hw *hw, u32 vlan, bool vlvf_bypass)
3070 {
3071 s32 regindex, first_empty_slot;
3072 u32 bits;
3073
3074 /* short cut the special case */
3075 if (vlan == 0)
3076 return 0;
3077
3078 /* if vlvf_bypass is set we don't want to use an empty slot, we
3079 * will simply bypass the VLVF if there are no entries present in the
3080 * VLVF that contain our VLAN
3081 */
3082 first_empty_slot = vlvf_bypass ? -ENOSPC : 0;
3083
3084 /* add VLAN enable bit for comparison */
3085 vlan |= IXGBE_VLVF_VIEN;
3086
3087 /* Search for the vlan id in the VLVF entries. Save off the first empty
3088 * slot found along the way.
3089 *
3090 * pre-decrement loop covering (IXGBE_VLVF_ENTRIES - 1) .. 1
3091 */
3092 for (regindex = IXGBE_VLVF_ENTRIES; --regindex;) {
3093 bits = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex));
3094 if (bits == vlan)
3095 return regindex;
3096 if (!first_empty_slot && !bits)
3097 first_empty_slot = regindex;
3098 }
3099
3100 /* If we are here then we didn't find the VLAN. Return first empty
3101 * slot we found during our search, else error.
3102 */
3103 if (!first_empty_slot)
3104 hw_dbg(hw, "No space in VLVF.\n");
3105
3106 return first_empty_slot ? : -ENOSPC;
3107 }
3108
3109 /**
3110 * ixgbe_set_vfta_generic - Set VLAN filter table
3111 * @hw: pointer to hardware structure
3112 * @vlan: VLAN id to write to VLAN filter
3113 * @vind: VMDq output index that maps queue to VLAN id in VFVFB
3114 * @vlan_on: boolean flag to turn on/off VLAN in VFVF
3115 * @vlvf_bypass: boolean flag indicating updating default pool is okay
3116 *
3117 * Turn on/off specified VLAN in the VLAN filter table.
3118 **/
ixgbe_set_vfta_generic(struct ixgbe_hw * hw,u32 vlan,u32 vind,bool vlan_on,bool vlvf_bypass)3119 s32 ixgbe_set_vfta_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind,
3120 bool vlan_on, bool vlvf_bypass)
3121 {
3122 u32 regidx, vfta_delta, vfta, bits;
3123 s32 vlvf_index;
3124
3125 if ((vlan > 4095) || (vind > 63))
3126 return -EINVAL;
3127
3128 /*
3129 * this is a 2 part operation - first the VFTA, then the
3130 * VLVF and VLVFB if VT Mode is set
3131 * We don't write the VFTA until we know the VLVF part succeeded.
3132 */
3133
3134 /* Part 1
3135 * The VFTA is a bitstring made up of 128 32-bit registers
3136 * that enable the particular VLAN id, much like the MTA:
3137 * bits[11-5]: which register
3138 * bits[4-0]: which bit in the register
3139 */
3140 regidx = vlan / 32;
3141 vfta_delta = BIT(vlan % 32);
3142 vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(regidx));
3143
3144 /* vfta_delta represents the difference between the current value
3145 * of vfta and the value we want in the register. Since the diff
3146 * is an XOR mask we can just update vfta using an XOR.
3147 */
3148 vfta_delta &= vlan_on ? ~vfta : vfta;
3149 vfta ^= vfta_delta;
3150
3151 /* Part 2
3152 * If VT Mode is set
3153 * Either vlan_on
3154 * make sure the vlan is in VLVF
3155 * set the vind bit in the matching VLVFB
3156 * Or !vlan_on
3157 * clear the pool bit and possibly the vind
3158 */
3159 if (!(IXGBE_READ_REG(hw, IXGBE_VT_CTL) & IXGBE_VT_CTL_VT_ENABLE))
3160 goto vfta_update;
3161
3162 vlvf_index = ixgbe_find_vlvf_slot(hw, vlan, vlvf_bypass);
3163 if (vlvf_index < 0) {
3164 if (vlvf_bypass)
3165 goto vfta_update;
3166 return vlvf_index;
3167 }
3168
3169 bits = IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32));
3170
3171 /* set the pool bit */
3172 bits |= BIT(vind % 32);
3173 if (vlan_on)
3174 goto vlvf_update;
3175
3176 /* clear the pool bit */
3177 bits ^= BIT(vind % 32);
3178
3179 if (!bits &&
3180 !IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + 1 - vind / 32))) {
3181 /* Clear VFTA first, then disable VLVF. Otherwise
3182 * we run the risk of stray packets leaking into
3183 * the PF via the default pool
3184 */
3185 if (vfta_delta)
3186 IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta);
3187
3188 /* disable VLVF and clear remaining bit from pool */
3189 IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), 0);
3190 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), 0);
3191
3192 return 0;
3193 }
3194
3195 /* If there are still bits set in the VLVFB registers
3196 * for the VLAN ID indicated we need to see if the
3197 * caller is requesting that we clear the VFTA entry bit.
3198 * If the caller has requested that we clear the VFTA
3199 * entry bit but there are still pools/VFs using this VLAN
3200 * ID entry then ignore the request. We're not worried
3201 * about the case where we're turning the VFTA VLAN ID
3202 * entry bit on, only when requested to turn it off as
3203 * there may be multiple pools and/or VFs using the
3204 * VLAN ID entry. In that case we cannot clear the
3205 * VFTA bit until all pools/VFs using that VLAN ID have also
3206 * been cleared. This will be indicated by "bits" being
3207 * zero.
3208 */
3209 vfta_delta = 0;
3210
3211 vlvf_update:
3212 /* record pool change and enable VLAN ID if not already enabled */
3213 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), bits);
3214 IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), IXGBE_VLVF_VIEN | vlan);
3215
3216 vfta_update:
3217 /* Update VFTA now that we are ready for traffic */
3218 if (vfta_delta)
3219 IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta);
3220
3221 return 0;
3222 }
3223
3224 /**
3225 * ixgbe_clear_vfta_generic - Clear VLAN filter table
3226 * @hw: pointer to hardware structure
3227 *
3228 * Clears the VLAN filer table, and the VMDq index associated with the filter
3229 **/
ixgbe_clear_vfta_generic(struct ixgbe_hw * hw)3230 s32 ixgbe_clear_vfta_generic(struct ixgbe_hw *hw)
3231 {
3232 u32 offset;
3233
3234 for (offset = 0; offset < hw->mac.vft_size; offset++)
3235 IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0);
3236
3237 for (offset = 0; offset < IXGBE_VLVF_ENTRIES; offset++) {
3238 IXGBE_WRITE_REG(hw, IXGBE_VLVF(offset), 0);
3239 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2), 0);
3240 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2 + 1), 0);
3241 }
3242
3243 return 0;
3244 }
3245
3246 /**
3247 * ixgbe_need_crosstalk_fix - Determine if we need to do cross talk fix
3248 * @hw: pointer to hardware structure
3249 *
3250 * Contains the logic to identify if we need to verify link for the
3251 * crosstalk fix
3252 **/
ixgbe_need_crosstalk_fix(struct ixgbe_hw * hw)3253 static bool ixgbe_need_crosstalk_fix(struct ixgbe_hw *hw)
3254 {
3255 /* Does FW say we need the fix */
3256 if (!hw->need_crosstalk_fix)
3257 return false;
3258
3259 /* Only consider SFP+ PHYs i.e. media type fiber */
3260 switch (hw->mac.ops.get_media_type(hw)) {
3261 case ixgbe_media_type_fiber:
3262 case ixgbe_media_type_fiber_qsfp:
3263 break;
3264 default:
3265 return false;
3266 }
3267
3268 return true;
3269 }
3270
3271 /**
3272 * ixgbe_check_mac_link_generic - Determine link and speed status
3273 * @hw: pointer to hardware structure
3274 * @speed: pointer to link speed
3275 * @link_up: true when link is up
3276 * @link_up_wait_to_complete: bool used to wait for link up or not
3277 *
3278 * Reads the links register to determine if link is up and the current speed
3279 **/
ixgbe_check_mac_link_generic(struct ixgbe_hw * hw,ixgbe_link_speed * speed,bool * link_up,bool link_up_wait_to_complete)3280 s32 ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
3281 bool *link_up, bool link_up_wait_to_complete)
3282 {
3283 u32 links_reg, links_orig;
3284 u32 i;
3285
3286 /* If Crosstalk fix enabled do the sanity check of making sure
3287 * the SFP+ cage is full.
3288 */
3289 if (ixgbe_need_crosstalk_fix(hw)) {
3290 u32 sfp_cage_full;
3291
3292 switch (hw->mac.type) {
3293 case ixgbe_mac_82599EB:
3294 sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
3295 IXGBE_ESDP_SDP2;
3296 break;
3297 case ixgbe_mac_X550EM_x:
3298 case ixgbe_mac_x550em_a:
3299 sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
3300 IXGBE_ESDP_SDP0;
3301 break;
3302 default:
3303 /* sanity check - No SFP+ devices here */
3304 sfp_cage_full = false;
3305 break;
3306 }
3307
3308 if (!sfp_cage_full) {
3309 *link_up = false;
3310 *speed = IXGBE_LINK_SPEED_UNKNOWN;
3311 return 0;
3312 }
3313 }
3314
3315 /* clear the old state */
3316 links_orig = IXGBE_READ_REG(hw, IXGBE_LINKS);
3317
3318 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
3319
3320 if (links_orig != links_reg) {
3321 hw_dbg(hw, "LINKS changed from %08X to %08X\n",
3322 links_orig, links_reg);
3323 }
3324
3325 if (link_up_wait_to_complete) {
3326 for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
3327 if (links_reg & IXGBE_LINKS_UP) {
3328 *link_up = true;
3329 break;
3330 } else {
3331 *link_up = false;
3332 }
3333 msleep(100);
3334 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
3335 }
3336 } else {
3337 if (links_reg & IXGBE_LINKS_UP)
3338 *link_up = true;
3339 else
3340 *link_up = false;
3341 }
3342
3343 switch (links_reg & IXGBE_LINKS_SPEED_82599) {
3344 case IXGBE_LINKS_SPEED_10G_82599:
3345 if ((hw->mac.type >= ixgbe_mac_X550) &&
3346 (links_reg & IXGBE_LINKS_SPEED_NON_STD))
3347 *speed = IXGBE_LINK_SPEED_2_5GB_FULL;
3348 else
3349 *speed = IXGBE_LINK_SPEED_10GB_FULL;
3350 break;
3351 case IXGBE_LINKS_SPEED_1G_82599:
3352 *speed = IXGBE_LINK_SPEED_1GB_FULL;
3353 break;
3354 case IXGBE_LINKS_SPEED_100_82599:
3355 if ((hw->mac.type >= ixgbe_mac_X550) &&
3356 (links_reg & IXGBE_LINKS_SPEED_NON_STD))
3357 *speed = IXGBE_LINK_SPEED_5GB_FULL;
3358 else
3359 *speed = IXGBE_LINK_SPEED_100_FULL;
3360 break;
3361 case IXGBE_LINKS_SPEED_10_X550EM_A:
3362 *speed = IXGBE_LINK_SPEED_UNKNOWN;
3363 if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
3364 hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) {
3365 *speed = IXGBE_LINK_SPEED_10_FULL;
3366 }
3367 break;
3368 default:
3369 *speed = IXGBE_LINK_SPEED_UNKNOWN;
3370 }
3371
3372 return 0;
3373 }
3374
3375 /**
3376 * ixgbe_get_wwn_prefix_generic - Get alternative WWNN/WWPN prefix from
3377 * the EEPROM
3378 * @hw: pointer to hardware structure
3379 * @wwnn_prefix: the alternative WWNN prefix
3380 * @wwpn_prefix: the alternative WWPN prefix
3381 *
3382 * This function will read the EEPROM from the alternative SAN MAC address
3383 * block to check the support for the alternative WWNN/WWPN prefix support.
3384 **/
ixgbe_get_wwn_prefix_generic(struct ixgbe_hw * hw,u16 * wwnn_prefix,u16 * wwpn_prefix)3385 s32 ixgbe_get_wwn_prefix_generic(struct ixgbe_hw *hw, u16 *wwnn_prefix,
3386 u16 *wwpn_prefix)
3387 {
3388 u16 offset, caps;
3389 u16 alt_san_mac_blk_offset;
3390
3391 /* clear output first */
3392 *wwnn_prefix = 0xFFFF;
3393 *wwpn_prefix = 0xFFFF;
3394
3395 /* check if alternative SAN MAC is supported */
3396 offset = IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR;
3397 if (hw->eeprom.ops.read(hw, offset, &alt_san_mac_blk_offset))
3398 goto wwn_prefix_err;
3399
3400 if ((alt_san_mac_blk_offset == 0) ||
3401 (alt_san_mac_blk_offset == 0xFFFF))
3402 return 0;
3403
3404 /* check capability in alternative san mac address block */
3405 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET;
3406 if (hw->eeprom.ops.read(hw, offset, &caps))
3407 goto wwn_prefix_err;
3408 if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN))
3409 return 0;
3410
3411 /* get the corresponding prefix for WWNN/WWPN */
3412 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET;
3413 if (hw->eeprom.ops.read(hw, offset, wwnn_prefix))
3414 hw_err(hw, "eeprom read at offset %d failed\n", offset);
3415
3416 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET;
3417 if (hw->eeprom.ops.read(hw, offset, wwpn_prefix))
3418 goto wwn_prefix_err;
3419
3420 return 0;
3421
3422 wwn_prefix_err:
3423 hw_err(hw, "eeprom read at offset %d failed\n", offset);
3424 return 0;
3425 }
3426
3427 /**
3428 * ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing
3429 * @hw: pointer to hardware structure
3430 * @enable: enable or disable switch for MAC anti-spoofing
3431 * @vf: Virtual Function pool - VF Pool to set for MAC anti-spoofing
3432 *
3433 **/
ixgbe_set_mac_anti_spoofing(struct ixgbe_hw * hw,bool enable,int vf)3434 void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
3435 {
3436 int vf_target_reg = vf >> 3;
3437 int vf_target_shift = vf % 8;
3438 u32 pfvfspoof;
3439
3440 if (hw->mac.type == ixgbe_mac_82598EB)
3441 return;
3442
3443 pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
3444 if (enable)
3445 pfvfspoof |= BIT(vf_target_shift);
3446 else
3447 pfvfspoof &= ~BIT(vf_target_shift);
3448 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof);
3449 }
3450
3451 /**
3452 * ixgbe_set_vlan_anti_spoofing - Enable/Disable VLAN anti-spoofing
3453 * @hw: pointer to hardware structure
3454 * @enable: enable or disable switch for VLAN anti-spoofing
3455 * @vf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing
3456 *
3457 **/
ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw * hw,bool enable,int vf)3458 void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
3459 {
3460 int vf_target_reg = vf >> 3;
3461 int vf_target_shift = vf % 8 + IXGBE_SPOOF_VLANAS_SHIFT;
3462 u32 pfvfspoof;
3463
3464 if (hw->mac.type == ixgbe_mac_82598EB)
3465 return;
3466
3467 pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
3468 if (enable)
3469 pfvfspoof |= BIT(vf_target_shift);
3470 else
3471 pfvfspoof &= ~BIT(vf_target_shift);
3472 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof);
3473 }
3474
3475 /**
3476 * ixgbe_get_device_caps_generic - Get additional device capabilities
3477 * @hw: pointer to hardware structure
3478 * @device_caps: the EEPROM word with the extra device capabilities
3479 *
3480 * This function will read the EEPROM location for the device capabilities,
3481 * and return the word through device_caps.
3482 **/
ixgbe_get_device_caps_generic(struct ixgbe_hw * hw,u16 * device_caps)3483 s32 ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps)
3484 {
3485 hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps);
3486
3487 return 0;
3488 }
3489
3490 /**
3491 * ixgbe_set_rxpba_generic - Initialize RX packet buffer
3492 * @hw: pointer to hardware structure
3493 * @num_pb: number of packet buffers to allocate
3494 * @headroom: reserve n KB of headroom
3495 * @strategy: packet buffer allocation strategy
3496 **/
ixgbe_set_rxpba_generic(struct ixgbe_hw * hw,int num_pb,u32 headroom,int strategy)3497 void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw,
3498 int num_pb,
3499 u32 headroom,
3500 int strategy)
3501 {
3502 u32 pbsize = hw->mac.rx_pb_size;
3503 int i = 0;
3504 u32 rxpktsize, txpktsize, txpbthresh;
3505
3506 /* Reserve headroom */
3507 pbsize -= headroom;
3508
3509 if (!num_pb)
3510 num_pb = 1;
3511
3512 /* Divide remaining packet buffer space amongst the number
3513 * of packet buffers requested using supplied strategy.
3514 */
3515 switch (strategy) {
3516 case (PBA_STRATEGY_WEIGHTED):
3517 /* pba_80_48 strategy weight first half of packet buffer with
3518 * 5/8 of the packet buffer space.
3519 */
3520 rxpktsize = ((pbsize * 5 * 2) / (num_pb * 8));
3521 pbsize -= rxpktsize * (num_pb / 2);
3522 rxpktsize <<= IXGBE_RXPBSIZE_SHIFT;
3523 for (; i < (num_pb / 2); i++)
3524 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
3525 fallthrough; /* configure remaining packet buffers */
3526 case (PBA_STRATEGY_EQUAL):
3527 /* Divide the remaining Rx packet buffer evenly among the TCs */
3528 rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT;
3529 for (; i < num_pb; i++)
3530 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
3531 break;
3532 default:
3533 break;
3534 }
3535
3536 /*
3537 * Setup Tx packet buffer and threshold equally for all TCs
3538 * TXPBTHRESH register is set in K so divide by 1024 and subtract
3539 * 10 since the largest packet we support is just over 9K.
3540 */
3541 txpktsize = IXGBE_TXPBSIZE_MAX / num_pb;
3542 txpbthresh = (txpktsize / 1024) - IXGBE_TXPKT_SIZE_MAX;
3543 for (i = 0; i < num_pb; i++) {
3544 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), txpktsize);
3545 IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), txpbthresh);
3546 }
3547
3548 /* Clear unused TCs, if any, to zero buffer size*/
3549 for (; i < IXGBE_MAX_PB; i++) {
3550 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0);
3551 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), 0);
3552 IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), 0);
3553 }
3554 }
3555
3556 /**
3557 * ixgbe_calculate_checksum - Calculate checksum for buffer
3558 * @buffer: pointer to EEPROM
3559 * @length: size of EEPROM to calculate a checksum for
3560 *
3561 * Calculates the checksum for some buffer on a specified length. The
3562 * checksum calculated is returned.
3563 **/
ixgbe_calculate_checksum(u8 * buffer,u32 length)3564 u8 ixgbe_calculate_checksum(u8 *buffer, u32 length)
3565 {
3566 u32 i;
3567 u8 sum = 0;
3568
3569 if (!buffer)
3570 return 0;
3571
3572 for (i = 0; i < length; i++)
3573 sum += buffer[i];
3574
3575 return (u8) (0 - sum);
3576 }
3577
3578 /**
3579 * ixgbe_hic_unlocked - Issue command to manageability block unlocked
3580 * @hw: pointer to the HW structure
3581 * @buffer: command to write and where the return status will be placed
3582 * @length: length of buffer, must be multiple of 4 bytes
3583 * @timeout: time in ms to wait for command completion
3584 *
3585 * Communicates with the manageability block. On success return 0
3586 * else returns semaphore error when encountering an error acquiring
3587 * semaphore, -EINVAL when incorrect parameters passed or -EIO when
3588 * command fails.
3589 *
3590 * This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held
3591 * by the caller.
3592 **/
ixgbe_hic_unlocked(struct ixgbe_hw * hw,u32 * buffer,u32 length,u32 timeout)3593 s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length,
3594 u32 timeout)
3595 {
3596 u32 hicr, i, fwsts;
3597 u16 dword_len;
3598
3599 if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
3600 hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
3601 return -EINVAL;
3602 }
3603
3604 /* Set bit 9 of FWSTS clearing FW reset indication */
3605 fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS);
3606 IXGBE_WRITE_REG(hw, IXGBE_FWSTS, fwsts | IXGBE_FWSTS_FWRI);
3607
3608 /* Check that the host interface is enabled. */
3609 hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
3610 if (!(hicr & IXGBE_HICR_EN)) {
3611 hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n");
3612 return -EIO;
3613 }
3614
3615 /* Calculate length in DWORDs. We must be DWORD aligned */
3616 if (length % sizeof(u32)) {
3617 hw_dbg(hw, "Buffer length failure, not aligned to dword");
3618 return -EINVAL;
3619 }
3620
3621 dword_len = length >> 2;
3622
3623 /* The device driver writes the relevant command block
3624 * into the ram area.
3625 */
3626 for (i = 0; i < dword_len; i++)
3627 IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG,
3628 i, (__force u32)cpu_to_le32(buffer[i]));
3629
3630 /* Setting this bit tells the ARC that a new command is pending. */
3631 IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C);
3632
3633 for (i = 0; i < timeout; i++) {
3634 hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
3635 if (!(hicr & IXGBE_HICR_C))
3636 break;
3637 usleep_range(1000, 2000);
3638 }
3639
3640 /* Check command successful completion. */
3641 if ((timeout && i == timeout) ||
3642 !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV))
3643 return -EIO;
3644
3645 return 0;
3646 }
3647
3648 /**
3649 * ixgbe_host_interface_command - Issue command to manageability block
3650 * @hw: pointer to the HW structure
3651 * @buffer: contains the command to write and where the return status will
3652 * be placed
3653 * @length: length of buffer, must be multiple of 4 bytes
3654 * @timeout: time in ms to wait for command completion
3655 * @return_data: read and return data from the buffer (true) or not (false)
3656 * Needed because FW structures are big endian and decoding of
3657 * these fields can be 8 bit or 16 bit based on command. Decoding
3658 * is not easily understood without making a table of commands.
3659 * So we will leave this up to the caller to read back the data
3660 * in these cases.
3661 *
3662 * Communicates with the manageability block. On success return 0
3663 * else return -EIO or -EINVAL.
3664 **/
ixgbe_host_interface_command(struct ixgbe_hw * hw,void * buffer,u32 length,u32 timeout,bool return_data)3665 s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
3666 u32 length, u32 timeout,
3667 bool return_data)
3668 {
3669 u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
3670 struct ixgbe_hic_hdr *hdr = buffer;
3671 u32 *u32arr = buffer;
3672 u16 buf_len, dword_len;
3673 s32 status;
3674 u32 bi;
3675
3676 if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
3677 hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
3678 return -EINVAL;
3679 }
3680 /* Take management host interface semaphore */
3681 status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
3682 if (status)
3683 return status;
3684
3685 status = ixgbe_hic_unlocked(hw, buffer, length, timeout);
3686 if (status)
3687 goto rel_out;
3688
3689 if (!return_data)
3690 goto rel_out;
3691
3692 /* Calculate length in DWORDs */
3693 dword_len = hdr_size >> 2;
3694
3695 /* first pull in the header so we know the buffer length */
3696 for (bi = 0; bi < dword_len; bi++) {
3697 u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
3698 le32_to_cpus(&u32arr[bi]);
3699 }
3700
3701 /* If there is any thing in data position pull it in */
3702 buf_len = hdr->buf_len;
3703 if (!buf_len)
3704 goto rel_out;
3705
3706 if (length < round_up(buf_len, 4) + hdr_size) {
3707 hw_dbg(hw, "Buffer not large enough for reply message.\n");
3708 status = -EIO;
3709 goto rel_out;
3710 }
3711
3712 /* Calculate length in DWORDs, add 3 for odd lengths */
3713 dword_len = (buf_len + 3) >> 2;
3714
3715 /* Pull in the rest of the buffer (bi is where we left off) */
3716 for (; bi <= dword_len; bi++) {
3717 u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
3718 le32_to_cpus(&u32arr[bi]);
3719 }
3720
3721 rel_out:
3722 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
3723
3724 return status;
3725 }
3726
3727 /**
3728 * ixgbe_set_fw_drv_ver_generic - Sends driver version to firmware
3729 * @hw: pointer to the HW structure
3730 * @maj: driver version major number
3731 * @min: driver version minor number
3732 * @build: driver version build number
3733 * @sub: driver version sub build number
3734 * @len: length of driver_ver string
3735 * @driver_ver: driver string
3736 *
3737 * Sends driver version number to firmware through the manageability
3738 * block. On success return 0
3739 * else returns -EBUSY when encountering an error acquiring
3740 * semaphore or -EIO when command fails.
3741 **/
ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw * hw,u8 maj,u8 min,u8 build,u8 sub,__always_unused u16 len,__always_unused const char * driver_ver)3742 s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
3743 u8 build, u8 sub, __always_unused u16 len,
3744 __always_unused const char *driver_ver)
3745 {
3746 struct ixgbe_hic_drv_info fw_cmd;
3747 int i;
3748 s32 ret_val;
3749
3750 fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
3751 fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN;
3752 fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
3753 fw_cmd.port_num = hw->bus.func;
3754 fw_cmd.ver_maj = maj;
3755 fw_cmd.ver_min = min;
3756 fw_cmd.ver_build = build;
3757 fw_cmd.ver_sub = sub;
3758 fw_cmd.hdr.checksum = 0;
3759 fw_cmd.pad = 0;
3760 fw_cmd.pad2 = 0;
3761 fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
3762 (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));
3763
3764 for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
3765 ret_val = ixgbe_host_interface_command(hw, &fw_cmd,
3766 sizeof(fw_cmd),
3767 IXGBE_HI_COMMAND_TIMEOUT,
3768 true);
3769 if (ret_val != 0)
3770 continue;
3771
3772 if (fw_cmd.hdr.cmd_or_resp.ret_status ==
3773 FW_CEM_RESP_STATUS_SUCCESS)
3774 ret_val = 0;
3775 else
3776 ret_val = -EIO;
3777
3778 break;
3779 }
3780
3781 return ret_val;
3782 }
3783
3784 /**
3785 * ixgbe_clear_tx_pending - Clear pending TX work from the PCIe fifo
3786 * @hw: pointer to the hardware structure
3787 *
3788 * The 82599 and x540 MACs can experience issues if TX work is still pending
3789 * when a reset occurs. This function prevents this by flushing the PCIe
3790 * buffers on the system.
3791 **/
ixgbe_clear_tx_pending(struct ixgbe_hw * hw)3792 void ixgbe_clear_tx_pending(struct ixgbe_hw *hw)
3793 {
3794 u32 gcr_ext, hlreg0, i, poll;
3795 u16 value;
3796
3797 /*
3798 * If double reset is not requested then all transactions should
3799 * already be clear and as such there is no work to do
3800 */
3801 if (!(hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED))
3802 return;
3803
3804 /*
3805 * Set loopback enable to prevent any transmits from being sent
3806 * should the link come up. This assumes that the RXCTRL.RXEN bit
3807 * has already been cleared.
3808 */
3809 hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
3810 IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0 | IXGBE_HLREG0_LPBK);
3811
3812 /* wait for a last completion before clearing buffers */
3813 IXGBE_WRITE_FLUSH(hw);
3814 usleep_range(3000, 6000);
3815
3816 /* Before proceeding, make sure that the PCIe block does not have
3817 * transactions pending.
3818 */
3819 poll = ixgbe_pcie_timeout_poll(hw);
3820 for (i = 0; i < poll; i++) {
3821 usleep_range(100, 200);
3822 value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS);
3823 if (ixgbe_removed(hw->hw_addr))
3824 break;
3825 if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
3826 break;
3827 }
3828
3829 /* initiate cleaning flow for buffers in the PCIe transaction layer */
3830 gcr_ext = IXGBE_READ_REG(hw, IXGBE_GCR_EXT);
3831 IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT,
3832 gcr_ext | IXGBE_GCR_EXT_BUFFERS_CLEAR);
3833
3834 /* Flush all writes and allow 20usec for all transactions to clear */
3835 IXGBE_WRITE_FLUSH(hw);
3836 udelay(20);
3837
3838 /* restore previous register values */
3839 IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr_ext);
3840 IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
3841 }
3842
3843 static const u8 ixgbe_emc_temp_data[4] = {
3844 IXGBE_EMC_INTERNAL_DATA,
3845 IXGBE_EMC_DIODE1_DATA,
3846 IXGBE_EMC_DIODE2_DATA,
3847 IXGBE_EMC_DIODE3_DATA
3848 };
3849 static const u8 ixgbe_emc_therm_limit[4] = {
3850 IXGBE_EMC_INTERNAL_THERM_LIMIT,
3851 IXGBE_EMC_DIODE1_THERM_LIMIT,
3852 IXGBE_EMC_DIODE2_THERM_LIMIT,
3853 IXGBE_EMC_DIODE3_THERM_LIMIT
3854 };
3855
3856 /**
3857 * ixgbe_get_ets_data - Extracts the ETS bit data
3858 * @hw: pointer to hardware structure
3859 * @ets_cfg: extected ETS data
3860 * @ets_offset: offset of ETS data
3861 *
3862 * Returns error code.
3863 **/
ixgbe_get_ets_data(struct ixgbe_hw * hw,u16 * ets_cfg,u16 * ets_offset)3864 static s32 ixgbe_get_ets_data(struct ixgbe_hw *hw, u16 *ets_cfg,
3865 u16 *ets_offset)
3866 {
3867 s32 status;
3868
3869 status = hw->eeprom.ops.read(hw, IXGBE_ETS_CFG, ets_offset);
3870 if (status)
3871 return status;
3872
3873 if ((*ets_offset == 0x0000) || (*ets_offset == 0xFFFF))
3874 return -EOPNOTSUPP;
3875
3876 status = hw->eeprom.ops.read(hw, *ets_offset, ets_cfg);
3877 if (status)
3878 return status;
3879
3880 if ((*ets_cfg & IXGBE_ETS_TYPE_MASK) != IXGBE_ETS_TYPE_EMC_SHIFTED)
3881 return -EOPNOTSUPP;
3882
3883 return 0;
3884 }
3885
3886 /**
3887 * ixgbe_get_thermal_sensor_data_generic - Gathers thermal sensor data
3888 * @hw: pointer to hardware structure
3889 *
3890 * Returns the thermal sensor data structure
3891 **/
ixgbe_get_thermal_sensor_data_generic(struct ixgbe_hw * hw)3892 s32 ixgbe_get_thermal_sensor_data_generic(struct ixgbe_hw *hw)
3893 {
3894 s32 status;
3895 u16 ets_offset;
3896 u16 ets_cfg;
3897 u16 ets_sensor;
3898 u8 num_sensors;
3899 u8 i;
3900 struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
3901
3902 /* Only support thermal sensors attached to physical port 0 */
3903 if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
3904 return -EOPNOTSUPP;
3905
3906 status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
3907 if (status)
3908 return status;
3909
3910 num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK);
3911 if (num_sensors > IXGBE_MAX_SENSORS)
3912 num_sensors = IXGBE_MAX_SENSORS;
3913
3914 for (i = 0; i < num_sensors; i++) {
3915 u8 sensor_index;
3916 u8 sensor_location;
3917
3918 status = hw->eeprom.ops.read(hw, (ets_offset + 1 + i),
3919 &ets_sensor);
3920 if (status)
3921 return status;
3922
3923 sensor_index = ((ets_sensor & IXGBE_ETS_DATA_INDEX_MASK) >>
3924 IXGBE_ETS_DATA_INDEX_SHIFT);
3925 sensor_location = ((ets_sensor & IXGBE_ETS_DATA_LOC_MASK) >>
3926 IXGBE_ETS_DATA_LOC_SHIFT);
3927
3928 if (sensor_location != 0) {
3929 status = hw->phy.ops.read_i2c_byte(hw,
3930 ixgbe_emc_temp_data[sensor_index],
3931 IXGBE_I2C_THERMAL_SENSOR_ADDR,
3932 &data->sensor[i].temp);
3933 if (status)
3934 return status;
3935 }
3936 }
3937
3938 return 0;
3939 }
3940
3941 /**
3942 * ixgbe_init_thermal_sensor_thresh_generic - Inits thermal sensor thresholds
3943 * @hw: pointer to hardware structure
3944 *
3945 * Inits the thermal sensor thresholds according to the NVM map
3946 * and save off the threshold and location values into mac.thermal_sensor_data
3947 **/
ixgbe_init_thermal_sensor_thresh_generic(struct ixgbe_hw * hw)3948 s32 ixgbe_init_thermal_sensor_thresh_generic(struct ixgbe_hw *hw)
3949 {
3950 s32 status;
3951 u16 ets_offset;
3952 u16 ets_cfg;
3953 u16 ets_sensor;
3954 u8 low_thresh_delta;
3955 u8 num_sensors;
3956 u8 therm_limit;
3957 u8 i;
3958 struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
3959
3960 memset(data, 0, sizeof(struct ixgbe_thermal_sensor_data));
3961
3962 /* Only support thermal sensors attached to physical port 0 */
3963 if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
3964 return -EOPNOTSUPP;
3965
3966 status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
3967 if (status)
3968 return status;
3969
3970 low_thresh_delta = ((ets_cfg & IXGBE_ETS_LTHRES_DELTA_MASK) >>
3971 IXGBE_ETS_LTHRES_DELTA_SHIFT);
3972 num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK);
3973 if (num_sensors > IXGBE_MAX_SENSORS)
3974 num_sensors = IXGBE_MAX_SENSORS;
3975
3976 for (i = 0; i < num_sensors; i++) {
3977 u8 sensor_index;
3978 u8 sensor_location;
3979
3980 if (hw->eeprom.ops.read(hw, ets_offset + 1 + i, &ets_sensor)) {
3981 hw_err(hw, "eeprom read at offset %d failed\n",
3982 ets_offset + 1 + i);
3983 continue;
3984 }
3985 sensor_index = ((ets_sensor & IXGBE_ETS_DATA_INDEX_MASK) >>
3986 IXGBE_ETS_DATA_INDEX_SHIFT);
3987 sensor_location = ((ets_sensor & IXGBE_ETS_DATA_LOC_MASK) >>
3988 IXGBE_ETS_DATA_LOC_SHIFT);
3989 therm_limit = ets_sensor & IXGBE_ETS_DATA_HTHRESH_MASK;
3990
3991 hw->phy.ops.write_i2c_byte(hw,
3992 ixgbe_emc_therm_limit[sensor_index],
3993 IXGBE_I2C_THERMAL_SENSOR_ADDR, therm_limit);
3994
3995 if (sensor_location == 0)
3996 continue;
3997
3998 data->sensor[i].location = sensor_location;
3999 data->sensor[i].caution_thresh = therm_limit;
4000 data->sensor[i].max_op_thresh = therm_limit - low_thresh_delta;
4001 }
4002
4003 return 0;
4004 }
4005
4006 /**
4007 * ixgbe_get_orom_version - Return option ROM from EEPROM
4008 *
4009 * @hw: pointer to hardware structure
4010 * @nvm_ver: pointer to output structure
4011 *
4012 * if valid option ROM version, nvm_ver->or_valid set to true
4013 * else nvm_ver->or_valid is false.
4014 **/
ixgbe_get_orom_version(struct ixgbe_hw * hw,struct ixgbe_nvm_version * nvm_ver)4015 void ixgbe_get_orom_version(struct ixgbe_hw *hw,
4016 struct ixgbe_nvm_version *nvm_ver)
4017 {
4018 u16 offset, eeprom_cfg_blkh, eeprom_cfg_blkl;
4019
4020 nvm_ver->or_valid = false;
4021 /* Option Rom may or may not be present. Start with pointer */
4022 hw->eeprom.ops.read(hw, NVM_OROM_OFFSET, &offset);
4023
4024 /* make sure offset is valid */
4025 if (offset == 0x0 || offset == NVM_INVALID_PTR)
4026 return;
4027
4028 hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_HI, &eeprom_cfg_blkh);
4029 hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_LOW, &eeprom_cfg_blkl);
4030
4031 /* option rom exists and is valid */
4032 if ((eeprom_cfg_blkl | eeprom_cfg_blkh) == 0x0 ||
4033 eeprom_cfg_blkl == NVM_VER_INVALID ||
4034 eeprom_cfg_blkh == NVM_VER_INVALID)
4035 return;
4036
4037 nvm_ver->or_valid = true;
4038 nvm_ver->or_major = eeprom_cfg_blkl >> NVM_OROM_SHIFT;
4039 nvm_ver->or_build = (eeprom_cfg_blkl << NVM_OROM_SHIFT) |
4040 (eeprom_cfg_blkh >> NVM_OROM_SHIFT);
4041 nvm_ver->or_patch = eeprom_cfg_blkh & NVM_OROM_PATCH_MASK;
4042 }
4043
4044 /**
4045 * ixgbe_get_oem_prod_version - Etrack ID from EEPROM
4046 * @hw: pointer to hardware structure
4047 * @nvm_ver: pointer to output structure
4048 *
4049 * if valid OEM product version, nvm_ver->oem_valid set to true
4050 * else nvm_ver->oem_valid is false.
4051 **/
ixgbe_get_oem_prod_version(struct ixgbe_hw * hw,struct ixgbe_nvm_version * nvm_ver)4052 void ixgbe_get_oem_prod_version(struct ixgbe_hw *hw,
4053 struct ixgbe_nvm_version *nvm_ver)
4054 {
4055 u16 rel_num, prod_ver, mod_len, cap, offset;
4056
4057 nvm_ver->oem_valid = false;
4058 hw->eeprom.ops.read(hw, NVM_OEM_PROD_VER_PTR, &offset);
4059
4060 /* Return is offset to OEM Product Version block is invalid */
4061 if (offset == 0x0 || offset == NVM_INVALID_PTR)
4062 return;
4063
4064 /* Read product version block */
4065 hw->eeprom.ops.read(hw, offset, &mod_len);
4066 hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_CAP_OFF, &cap);
4067
4068 /* Return if OEM product version block is invalid */
4069 if (mod_len != NVM_OEM_PROD_VER_MOD_LEN ||
4070 (cap & NVM_OEM_PROD_VER_CAP_MASK) != 0x0)
4071 return;
4072
4073 hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_L, &prod_ver);
4074 hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_H, &rel_num);
4075
4076 /* Return if version is invalid */
4077 if ((rel_num | prod_ver) == 0x0 ||
4078 rel_num == NVM_VER_INVALID || prod_ver == NVM_VER_INVALID)
4079 return;
4080
4081 nvm_ver->oem_major = prod_ver >> NVM_VER_SHIFT;
4082 nvm_ver->oem_minor = prod_ver & NVM_VER_MASK;
4083 nvm_ver->oem_release = rel_num;
4084 nvm_ver->oem_valid = true;
4085 }
4086
4087 /**
4088 * ixgbe_get_etk_id - Return Etrack ID from EEPROM
4089 *
4090 * @hw: pointer to hardware structure
4091 * @nvm_ver: pointer to output structure
4092 *
4093 * word read errors will return 0xFFFF
4094 **/
ixgbe_get_etk_id(struct ixgbe_hw * hw,struct ixgbe_nvm_version * nvm_ver)4095 void ixgbe_get_etk_id(struct ixgbe_hw *hw,
4096 struct ixgbe_nvm_version *nvm_ver)
4097 {
4098 u16 etk_id_l, etk_id_h;
4099
4100 if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_LOW, &etk_id_l))
4101 etk_id_l = NVM_VER_INVALID;
4102 if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_HI, &etk_id_h))
4103 etk_id_h = NVM_VER_INVALID;
4104
4105 /* The word order for the version format is determined by high order
4106 * word bit 15.
4107 */
4108 if ((etk_id_h & NVM_ETK_VALID) == 0) {
4109 nvm_ver->etk_id = etk_id_h;
4110 nvm_ver->etk_id |= (etk_id_l << NVM_ETK_SHIFT);
4111 } else {
4112 nvm_ver->etk_id = etk_id_l;
4113 nvm_ver->etk_id |= (etk_id_h << NVM_ETK_SHIFT);
4114 }
4115 }
4116
ixgbe_disable_rx_generic(struct ixgbe_hw * hw)4117 void ixgbe_disable_rx_generic(struct ixgbe_hw *hw)
4118 {
4119 u32 rxctrl;
4120
4121 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
4122 if (rxctrl & IXGBE_RXCTRL_RXEN) {
4123 if (hw->mac.type != ixgbe_mac_82598EB) {
4124 u32 pfdtxgswc;
4125
4126 pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
4127 if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) {
4128 pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN;
4129 IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
4130 hw->mac.set_lben = true;
4131 } else {
4132 hw->mac.set_lben = false;
4133 }
4134 }
4135 rxctrl &= ~IXGBE_RXCTRL_RXEN;
4136 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl);
4137 }
4138 }
4139
ixgbe_enable_rx_generic(struct ixgbe_hw * hw)4140 void ixgbe_enable_rx_generic(struct ixgbe_hw *hw)
4141 {
4142 u32 rxctrl;
4143
4144 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
4145 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, (rxctrl | IXGBE_RXCTRL_RXEN));
4146
4147 if (hw->mac.type != ixgbe_mac_82598EB) {
4148 if (hw->mac.set_lben) {
4149 u32 pfdtxgswc;
4150
4151 pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
4152 pfdtxgswc |= IXGBE_PFDTXGSWC_VT_LBEN;
4153 IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
4154 hw->mac.set_lben = false;
4155 }
4156 }
4157 }
4158
4159 /** ixgbe_mng_present - returns true when management capability is present
4160 * @hw: pointer to hardware structure
4161 **/
ixgbe_mng_present(struct ixgbe_hw * hw)4162 bool ixgbe_mng_present(struct ixgbe_hw *hw)
4163 {
4164 u32 fwsm;
4165
4166 if (hw->mac.type < ixgbe_mac_82599EB)
4167 return false;
4168
4169 fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM(hw));
4170
4171 return !!(fwsm & IXGBE_FWSM_FW_MODE_PT);
4172 }
4173
4174 /**
4175 * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
4176 * @hw: pointer to hardware structure
4177 * @speed: new link speed
4178 * @autoneg_wait_to_complete: true when waiting for completion is needed
4179 *
4180 * Set the link speed in the MAC and/or PHY register and restarts link.
4181 */
ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw * hw,ixgbe_link_speed speed,bool autoneg_wait_to_complete)4182 s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
4183 ixgbe_link_speed speed,
4184 bool autoneg_wait_to_complete)
4185 {
4186 ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
4187 ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
4188 s32 status = 0;
4189 u32 speedcnt = 0;
4190 u32 i = 0;
4191 bool autoneg, link_up = false;
4192
4193 /* Mask off requested but non-supported speeds */
4194 status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg);
4195 if (status)
4196 return status;
4197
4198 speed &= link_speed;
4199
4200 /* Try each speed one by one, highest priority first. We do this in
4201 * software because 10Gb fiber doesn't support speed autonegotiation.
4202 */
4203 if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
4204 speedcnt++;
4205 highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
4206
4207 /* Set the module link speed */
4208 switch (hw->phy.media_type) {
4209 case ixgbe_media_type_fiber:
4210 hw->mac.ops.set_rate_select_speed(hw,
4211 IXGBE_LINK_SPEED_10GB_FULL);
4212 break;
4213 case ixgbe_media_type_fiber_qsfp:
4214 /* QSFP module automatically detects MAC link speed */
4215 break;
4216 default:
4217 hw_dbg(hw, "Unexpected media type\n");
4218 break;
4219 }
4220
4221 /* Allow module to change analog characteristics (1G->10G) */
4222 msleep(40);
4223
4224 status = hw->mac.ops.setup_mac_link(hw,
4225 IXGBE_LINK_SPEED_10GB_FULL,
4226 autoneg_wait_to_complete);
4227 if (status)
4228 return status;
4229
4230 /* Flap the Tx laser if it has not already been done */
4231 if (hw->mac.ops.flap_tx_laser)
4232 hw->mac.ops.flap_tx_laser(hw);
4233
4234 /* Wait for the controller to acquire link. Per IEEE 802.3ap,
4235 * Section 73.10.2, we may have to wait up to 500ms if KR is
4236 * attempted. 82599 uses the same timing for 10g SFI.
4237 */
4238 for (i = 0; i < 5; i++) {
4239 /* Wait for the link partner to also set speed */
4240 msleep(100);
4241
4242 /* If we have link, just jump out */
4243 status = hw->mac.ops.check_link(hw, &link_speed,
4244 &link_up, false);
4245 if (status)
4246 return status;
4247
4248 if (link_up)
4249 goto out;
4250 }
4251 }
4252
4253 if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
4254 speedcnt++;
4255 if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
4256 highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
4257
4258 /* Set the module link speed */
4259 switch (hw->phy.media_type) {
4260 case ixgbe_media_type_fiber:
4261 hw->mac.ops.set_rate_select_speed(hw,
4262 IXGBE_LINK_SPEED_1GB_FULL);
4263 break;
4264 case ixgbe_media_type_fiber_qsfp:
4265 /* QSFP module automatically detects link speed */
4266 break;
4267 default:
4268 hw_dbg(hw, "Unexpected media type\n");
4269 break;
4270 }
4271
4272 /* Allow module to change analog characteristics (10G->1G) */
4273 msleep(40);
4274
4275 status = hw->mac.ops.setup_mac_link(hw,
4276 IXGBE_LINK_SPEED_1GB_FULL,
4277 autoneg_wait_to_complete);
4278 if (status)
4279 return status;
4280
4281 /* Flap the Tx laser if it has not already been done */
4282 if (hw->mac.ops.flap_tx_laser)
4283 hw->mac.ops.flap_tx_laser(hw);
4284
4285 /* Wait for the link partner to also set speed */
4286 msleep(100);
4287
4288 /* If we have link, just jump out */
4289 status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
4290 false);
4291 if (status)
4292 return status;
4293
4294 if (link_up)
4295 goto out;
4296 }
4297
4298 /* We didn't get link. Configure back to the highest speed we tried,
4299 * (if there was more than one). We call ourselves back with just the
4300 * single highest speed that the user requested.
4301 */
4302 if (speedcnt > 1)
4303 status = ixgbe_setup_mac_link_multispeed_fiber(hw,
4304 highest_link_speed,
4305 autoneg_wait_to_complete);
4306
4307 out:
4308 /* Set autoneg_advertised value based on input link speed */
4309 hw->phy.autoneg_advertised = 0;
4310
4311 if (speed & IXGBE_LINK_SPEED_10GB_FULL)
4312 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
4313
4314 if (speed & IXGBE_LINK_SPEED_1GB_FULL)
4315 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
4316
4317 return status;
4318 }
4319
4320 /**
4321 * ixgbe_set_soft_rate_select_speed - Set module link speed
4322 * @hw: pointer to hardware structure
4323 * @speed: link speed to set
4324 *
4325 * Set module link speed via the soft rate select.
4326 */
ixgbe_set_soft_rate_select_speed(struct ixgbe_hw * hw,ixgbe_link_speed speed)4327 void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw,
4328 ixgbe_link_speed speed)
4329 {
4330 s32 status;
4331 u8 rs, eeprom_data;
4332
4333 switch (speed) {
4334 case IXGBE_LINK_SPEED_10GB_FULL:
4335 /* one bit mask same as setting on */
4336 rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
4337 break;
4338 case IXGBE_LINK_SPEED_1GB_FULL:
4339 rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
4340 break;
4341 default:
4342 hw_dbg(hw, "Invalid fixed module speed\n");
4343 return;
4344 }
4345
4346 /* Set RS0 */
4347 status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
4348 IXGBE_I2C_EEPROM_DEV_ADDR2,
4349 &eeprom_data);
4350 if (status) {
4351 hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
4352 return;
4353 }
4354
4355 eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
4356
4357 status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
4358 IXGBE_I2C_EEPROM_DEV_ADDR2,
4359 eeprom_data);
4360 if (status) {
4361 hw_dbg(hw, "Failed to write Rx Rate Select RS0\n");
4362 return;
4363 }
4364
4365 /* Set RS1 */
4366 status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
4367 IXGBE_I2C_EEPROM_DEV_ADDR2,
4368 &eeprom_data);
4369 if (status) {
4370 hw_dbg(hw, "Failed to read Rx Rate Select RS1\n");
4371 return;
4372 }
4373
4374 eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
4375
4376 status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
4377 IXGBE_I2C_EEPROM_DEV_ADDR2,
4378 eeprom_data);
4379 if (status) {
4380 hw_dbg(hw, "Failed to write Rx Rate Select RS1\n");
4381 return;
4382 }
4383 }
4384