1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Driver for CLPS711x serial ports
4 *
5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
6 *
7 * Copyright 1999 ARM Limited
8 * Copyright (C) 2000 Deep Blue Solutions Ltd.
9 */
10
11 #include <linux/module.h>
12 #include <linux/device.h>
13 #include <linux/console.h>
14 #include <linux/serial_core.h>
15 #include <linux/serial.h>
16 #include <linux/clk.h>
17 #include <linux/io.h>
18 #include <linux/tty.h>
19 #include <linux/tty_flip.h>
20 #include <linux/ioport.h>
21 #include <linux/of.h>
22 #include <linux/platform_device.h>
23 #include <linux/regmap.h>
24
25 #include <linux/mfd/syscon.h>
26 #include <linux/mfd/syscon/clps711x.h>
27
28 #include "serial_mctrl_gpio.h"
29
30 #define UART_CLPS711X_DEVNAME "ttyCL"
31 #define UART_CLPS711X_NR 2
32 #define UART_CLPS711X_MAJOR 204
33 #define UART_CLPS711X_MINOR 40
34
35 #define UARTDR_OFFSET (0x00)
36 #define UBRLCR_OFFSET (0x40)
37
38 #define UARTDR_FRMERR (1 << 8)
39 #define UARTDR_PARERR (1 << 9)
40 #define UARTDR_OVERR (1 << 10)
41
42 #define UBRLCR_BAUD_MASK ((1 << 12) - 1)
43 #define UBRLCR_BREAK (1 << 12)
44 #define UBRLCR_PRTEN (1 << 13)
45 #define UBRLCR_EVENPRT (1 << 14)
46 #define UBRLCR_XSTOP (1 << 15)
47 #define UBRLCR_FIFOEN (1 << 16)
48 #define UBRLCR_WRDLEN5 (0 << 17)
49 #define UBRLCR_WRDLEN6 (1 << 17)
50 #define UBRLCR_WRDLEN7 (2 << 17)
51 #define UBRLCR_WRDLEN8 (3 << 17)
52 #define UBRLCR_WRDLEN_MASK (3 << 17)
53
54 struct clps711x_port {
55 struct uart_port port;
56 unsigned int tx_enabled;
57 int rx_irq;
58 struct regmap *syscon;
59 struct mctrl_gpios *gpios;
60 };
61
62 static struct uart_driver clps711x_uart = {
63 .owner = THIS_MODULE,
64 .driver_name = UART_CLPS711X_DEVNAME,
65 .dev_name = UART_CLPS711X_DEVNAME,
66 .major = UART_CLPS711X_MAJOR,
67 .minor = UART_CLPS711X_MINOR,
68 .nr = UART_CLPS711X_NR,
69 };
70
uart_clps711x_stop_tx(struct uart_port * port)71 static void uart_clps711x_stop_tx(struct uart_port *port)
72 {
73 struct clps711x_port *s = dev_get_drvdata(port->dev);
74
75 if (s->tx_enabled) {
76 disable_irq(port->irq);
77 s->tx_enabled = 0;
78 }
79 }
80
uart_clps711x_start_tx(struct uart_port * port)81 static void uart_clps711x_start_tx(struct uart_port *port)
82 {
83 struct clps711x_port *s = dev_get_drvdata(port->dev);
84
85 if (!s->tx_enabled) {
86 s->tx_enabled = 1;
87 enable_irq(port->irq);
88 }
89 }
90
uart_clps711x_int_rx(int irq,void * dev_id)91 static irqreturn_t uart_clps711x_int_rx(int irq, void *dev_id)
92 {
93 struct uart_port *port = dev_id;
94 struct clps711x_port *s = dev_get_drvdata(port->dev);
95 unsigned int status, flg;
96 u16 ch;
97
98 for (;;) {
99 u32 sysflg = 0;
100
101 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
102 if (sysflg & SYSFLG_URXFE)
103 break;
104
105 ch = readw(port->membase + UARTDR_OFFSET);
106 status = ch & (UARTDR_FRMERR | UARTDR_PARERR | UARTDR_OVERR);
107 ch &= 0xff;
108
109 port->icount.rx++;
110 flg = TTY_NORMAL;
111
112 if (unlikely(status)) {
113 if (status & UARTDR_PARERR)
114 port->icount.parity++;
115 else if (status & UARTDR_FRMERR)
116 port->icount.frame++;
117 else if (status & UARTDR_OVERR)
118 port->icount.overrun++;
119
120 status &= port->read_status_mask;
121
122 if (status & UARTDR_PARERR)
123 flg = TTY_PARITY;
124 else if (status & UARTDR_FRMERR)
125 flg = TTY_FRAME;
126 else if (status & UARTDR_OVERR)
127 flg = TTY_OVERRUN;
128 }
129
130 if (uart_handle_sysrq_char(port, ch))
131 continue;
132
133 if (status & port->ignore_status_mask)
134 continue;
135
136 uart_insert_char(port, status, UARTDR_OVERR, ch, flg);
137 }
138
139 tty_flip_buffer_push(&port->state->port);
140
141 return IRQ_HANDLED;
142 }
143
uart_clps711x_int_tx(int irq,void * dev_id)144 static irqreturn_t uart_clps711x_int_tx(int irq, void *dev_id)
145 {
146 struct uart_port *port = dev_id;
147 struct clps711x_port *s = dev_get_drvdata(port->dev);
148 struct circ_buf *xmit = &port->state->xmit;
149
150 if (port->x_char) {
151 writew(port->x_char, port->membase + UARTDR_OFFSET);
152 port->icount.tx++;
153 port->x_char = 0;
154 return IRQ_HANDLED;
155 }
156
157 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
158 if (s->tx_enabled) {
159 disable_irq_nosync(port->irq);
160 s->tx_enabled = 0;
161 }
162 return IRQ_HANDLED;
163 }
164
165 while (!uart_circ_empty(xmit)) {
166 u32 sysflg = 0;
167
168 writew(xmit->buf[xmit->tail], port->membase + UARTDR_OFFSET);
169 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
170 port->icount.tx++;
171
172 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
173 if (sysflg & SYSFLG_UTXFF)
174 break;
175 }
176
177 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
178 uart_write_wakeup(port);
179
180 return IRQ_HANDLED;
181 }
182
uart_clps711x_tx_empty(struct uart_port * port)183 static unsigned int uart_clps711x_tx_empty(struct uart_port *port)
184 {
185 struct clps711x_port *s = dev_get_drvdata(port->dev);
186 u32 sysflg = 0;
187
188 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
189
190 return (sysflg & SYSFLG_UBUSY) ? 0 : TIOCSER_TEMT;
191 }
192
uart_clps711x_get_mctrl(struct uart_port * port)193 static unsigned int uart_clps711x_get_mctrl(struct uart_port *port)
194 {
195 unsigned int result = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR;
196 struct clps711x_port *s = dev_get_drvdata(port->dev);
197
198 return mctrl_gpio_get(s->gpios, &result);
199 }
200
uart_clps711x_set_mctrl(struct uart_port * port,unsigned int mctrl)201 static void uart_clps711x_set_mctrl(struct uart_port *port, unsigned int mctrl)
202 {
203 struct clps711x_port *s = dev_get_drvdata(port->dev);
204
205 mctrl_gpio_set(s->gpios, mctrl);
206 }
207
uart_clps711x_break_ctl(struct uart_port * port,int break_state)208 static void uart_clps711x_break_ctl(struct uart_port *port, int break_state)
209 {
210 unsigned int ubrlcr;
211
212 ubrlcr = readl(port->membase + UBRLCR_OFFSET);
213 if (break_state)
214 ubrlcr |= UBRLCR_BREAK;
215 else
216 ubrlcr &= ~UBRLCR_BREAK;
217 writel(ubrlcr, port->membase + UBRLCR_OFFSET);
218 }
219
uart_clps711x_set_ldisc(struct uart_port * port,struct ktermios * termios)220 static void uart_clps711x_set_ldisc(struct uart_port *port,
221 struct ktermios *termios)
222 {
223 if (!port->line) {
224 struct clps711x_port *s = dev_get_drvdata(port->dev);
225
226 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON1_SIREN,
227 (termios->c_line == N_IRDA) ? SYSCON1_SIREN : 0);
228 }
229 }
230
uart_clps711x_startup(struct uart_port * port)231 static int uart_clps711x_startup(struct uart_port *port)
232 {
233 struct clps711x_port *s = dev_get_drvdata(port->dev);
234
235 /* Disable break */
236 writel(readl(port->membase + UBRLCR_OFFSET) & ~UBRLCR_BREAK,
237 port->membase + UBRLCR_OFFSET);
238
239 /* Enable the port */
240 return regmap_update_bits(s->syscon, SYSCON_OFFSET,
241 SYSCON_UARTEN, SYSCON_UARTEN);
242 }
243
uart_clps711x_shutdown(struct uart_port * port)244 static void uart_clps711x_shutdown(struct uart_port *port)
245 {
246 struct clps711x_port *s = dev_get_drvdata(port->dev);
247
248 /* Disable the port */
249 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON_UARTEN, 0);
250 }
251
uart_clps711x_set_termios(struct uart_port * port,struct ktermios * termios,struct ktermios * old)252 static void uart_clps711x_set_termios(struct uart_port *port,
253 struct ktermios *termios,
254 struct ktermios *old)
255 {
256 u32 ubrlcr;
257 unsigned int baud, quot;
258
259 /* Mask termios capabilities we don't support */
260 termios->c_cflag &= ~CMSPAR;
261 termios->c_iflag &= ~(BRKINT | IGNBRK);
262
263 /* Ask the core to calculate the divisor for us */
264 baud = uart_get_baud_rate(port, termios, old, port->uartclk / 4096,
265 port->uartclk / 16);
266 quot = uart_get_divisor(port, baud);
267
268 switch (termios->c_cflag & CSIZE) {
269 case CS5:
270 ubrlcr = UBRLCR_WRDLEN5;
271 break;
272 case CS6:
273 ubrlcr = UBRLCR_WRDLEN6;
274 break;
275 case CS7:
276 ubrlcr = UBRLCR_WRDLEN7;
277 break;
278 case CS8:
279 default:
280 ubrlcr = UBRLCR_WRDLEN8;
281 break;
282 }
283
284 if (termios->c_cflag & CSTOPB)
285 ubrlcr |= UBRLCR_XSTOP;
286
287 if (termios->c_cflag & PARENB) {
288 ubrlcr |= UBRLCR_PRTEN;
289 if (!(termios->c_cflag & PARODD))
290 ubrlcr |= UBRLCR_EVENPRT;
291 }
292
293 /* Enable FIFO */
294 ubrlcr |= UBRLCR_FIFOEN;
295
296 /* Set read status mask */
297 port->read_status_mask = UARTDR_OVERR;
298 if (termios->c_iflag & INPCK)
299 port->read_status_mask |= UARTDR_PARERR | UARTDR_FRMERR;
300
301 /* Set status ignore mask */
302 port->ignore_status_mask = 0;
303 if (!(termios->c_cflag & CREAD))
304 port->ignore_status_mask |= UARTDR_OVERR | UARTDR_PARERR |
305 UARTDR_FRMERR;
306
307 uart_update_timeout(port, termios->c_cflag, baud);
308
309 writel(ubrlcr | (quot - 1), port->membase + UBRLCR_OFFSET);
310 }
311
uart_clps711x_type(struct uart_port * port)312 static const char *uart_clps711x_type(struct uart_port *port)
313 {
314 return (port->type == PORT_CLPS711X) ? "CLPS711X" : NULL;
315 }
316
uart_clps711x_config_port(struct uart_port * port,int flags)317 static void uart_clps711x_config_port(struct uart_port *port, int flags)
318 {
319 if (flags & UART_CONFIG_TYPE)
320 port->type = PORT_CLPS711X;
321 }
322
uart_clps711x_nop_void(struct uart_port * port)323 static void uart_clps711x_nop_void(struct uart_port *port)
324 {
325 }
326
uart_clps711x_nop_int(struct uart_port * port)327 static int uart_clps711x_nop_int(struct uart_port *port)
328 {
329 return 0;
330 }
331
332 static const struct uart_ops uart_clps711x_ops = {
333 .tx_empty = uart_clps711x_tx_empty,
334 .set_mctrl = uart_clps711x_set_mctrl,
335 .get_mctrl = uart_clps711x_get_mctrl,
336 .stop_tx = uart_clps711x_stop_tx,
337 .start_tx = uart_clps711x_start_tx,
338 .stop_rx = uart_clps711x_nop_void,
339 .break_ctl = uart_clps711x_break_ctl,
340 .set_ldisc = uart_clps711x_set_ldisc,
341 .startup = uart_clps711x_startup,
342 .shutdown = uart_clps711x_shutdown,
343 .set_termios = uart_clps711x_set_termios,
344 .type = uart_clps711x_type,
345 .config_port = uart_clps711x_config_port,
346 .release_port = uart_clps711x_nop_void,
347 .request_port = uart_clps711x_nop_int,
348 };
349
350 #ifdef CONFIG_SERIAL_CLPS711X_CONSOLE
uart_clps711x_console_putchar(struct uart_port * port,int ch)351 static void uart_clps711x_console_putchar(struct uart_port *port, int ch)
352 {
353 struct clps711x_port *s = dev_get_drvdata(port->dev);
354 u32 sysflg = 0;
355
356 /* Wait for FIFO is not full */
357 do {
358 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
359 } while (sysflg & SYSFLG_UTXFF);
360
361 writew(ch, port->membase + UARTDR_OFFSET);
362 }
363
uart_clps711x_console_write(struct console * co,const char * c,unsigned n)364 static void uart_clps711x_console_write(struct console *co, const char *c,
365 unsigned n)
366 {
367 struct uart_port *port = clps711x_uart.state[co->index].uart_port;
368 struct clps711x_port *s = dev_get_drvdata(port->dev);
369 u32 sysflg = 0;
370
371 uart_console_write(port, c, n, uart_clps711x_console_putchar);
372
373 /* Wait for transmitter to become empty */
374 do {
375 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
376 } while (sysflg & SYSFLG_UBUSY);
377 }
378
uart_clps711x_console_setup(struct console * co,char * options)379 static int uart_clps711x_console_setup(struct console *co, char *options)
380 {
381 int baud = 38400, bits = 8, parity = 'n', flow = 'n';
382 int ret, index = co->index;
383 struct clps711x_port *s;
384 struct uart_port *port;
385 unsigned int quot;
386 u32 ubrlcr;
387
388 if (index < 0 || index >= UART_CLPS711X_NR)
389 return -EINVAL;
390
391 port = clps711x_uart.state[index].uart_port;
392 if (!port)
393 return -ENODEV;
394
395 s = dev_get_drvdata(port->dev);
396
397 if (!options) {
398 u32 syscon = 0;
399
400 regmap_read(s->syscon, SYSCON_OFFSET, &syscon);
401 if (syscon & SYSCON_UARTEN) {
402 ubrlcr = readl(port->membase + UBRLCR_OFFSET);
403
404 if (ubrlcr & UBRLCR_PRTEN) {
405 if (ubrlcr & UBRLCR_EVENPRT)
406 parity = 'e';
407 else
408 parity = 'o';
409 }
410
411 if ((ubrlcr & UBRLCR_WRDLEN_MASK) == UBRLCR_WRDLEN7)
412 bits = 7;
413
414 quot = ubrlcr & UBRLCR_BAUD_MASK;
415 baud = port->uartclk / (16 * (quot + 1));
416 }
417 } else
418 uart_parse_options(options, &baud, &parity, &bits, &flow);
419
420 ret = uart_set_options(port, co, baud, parity, bits, flow);
421 if (ret)
422 return ret;
423
424 return regmap_update_bits(s->syscon, SYSCON_OFFSET,
425 SYSCON_UARTEN, SYSCON_UARTEN);
426 }
427
428 static struct console clps711x_console = {
429 .name = UART_CLPS711X_DEVNAME,
430 .device = uart_console_device,
431 .write = uart_clps711x_console_write,
432 .setup = uart_clps711x_console_setup,
433 .flags = CON_PRINTBUFFER,
434 .index = -1,
435 };
436 #endif
437
uart_clps711x_probe(struct platform_device * pdev)438 static int uart_clps711x_probe(struct platform_device *pdev)
439 {
440 struct device_node *np = pdev->dev.of_node;
441 struct clps711x_port *s;
442 struct resource *res;
443 struct clk *uart_clk;
444 int irq, ret;
445
446 s = devm_kzalloc(&pdev->dev, sizeof(*s), GFP_KERNEL);
447 if (!s)
448 return -ENOMEM;
449
450 uart_clk = devm_clk_get(&pdev->dev, NULL);
451 if (IS_ERR(uart_clk))
452 return PTR_ERR(uart_clk);
453
454 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
455 s->port.membase = devm_ioremap_resource(&pdev->dev, res);
456 if (IS_ERR(s->port.membase))
457 return PTR_ERR(s->port.membase);
458
459 irq = platform_get_irq(pdev, 0);
460 if (irq < 0)
461 return irq;
462 s->port.irq = irq;
463
464 s->rx_irq = platform_get_irq(pdev, 1);
465 if (s->rx_irq < 0)
466 return s->rx_irq;
467
468 s->syscon = syscon_regmap_lookup_by_phandle(np, "syscon");
469 if (IS_ERR(s->syscon))
470 return PTR_ERR(s->syscon);
471
472 s->port.line = of_alias_get_id(np, "serial");
473 s->port.dev = &pdev->dev;
474 s->port.iotype = UPIO_MEM32;
475 s->port.mapbase = res->start;
476 s->port.type = PORT_CLPS711X;
477 s->port.fifosize = 16;
478 s->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_CLPS711X_CONSOLE);
479 s->port.flags = UPF_SKIP_TEST | UPF_FIXED_TYPE;
480 s->port.uartclk = clk_get_rate(uart_clk);
481 s->port.ops = &uart_clps711x_ops;
482
483 platform_set_drvdata(pdev, s);
484
485 s->gpios = mctrl_gpio_init_noauto(&pdev->dev, 0);
486 if (IS_ERR(s->gpios))
487 return PTR_ERR(s->gpios);
488
489 ret = uart_add_one_port(&clps711x_uart, &s->port);
490 if (ret)
491 return ret;
492
493 /* Disable port */
494 if (!uart_console(&s->port))
495 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON_UARTEN, 0);
496
497 s->tx_enabled = 1;
498
499 ret = devm_request_irq(&pdev->dev, s->port.irq, uart_clps711x_int_tx, 0,
500 dev_name(&pdev->dev), &s->port);
501 if (ret) {
502 uart_remove_one_port(&clps711x_uart, &s->port);
503 return ret;
504 }
505
506 ret = devm_request_irq(&pdev->dev, s->rx_irq, uart_clps711x_int_rx, 0,
507 dev_name(&pdev->dev), &s->port);
508 if (ret)
509 uart_remove_one_port(&clps711x_uart, &s->port);
510
511 return ret;
512 }
513
uart_clps711x_remove(struct platform_device * pdev)514 static int uart_clps711x_remove(struct platform_device *pdev)
515 {
516 struct clps711x_port *s = platform_get_drvdata(pdev);
517
518 return uart_remove_one_port(&clps711x_uart, &s->port);
519 }
520
521 static const struct of_device_id __maybe_unused clps711x_uart_dt_ids[] = {
522 { .compatible = "cirrus,ep7209-uart", },
523 { }
524 };
525 MODULE_DEVICE_TABLE(of, clps711x_uart_dt_ids);
526
527 static struct platform_driver clps711x_uart_platform = {
528 .driver = {
529 .name = "clps711x-uart",
530 .of_match_table = of_match_ptr(clps711x_uart_dt_ids),
531 },
532 .probe = uart_clps711x_probe,
533 .remove = uart_clps711x_remove,
534 };
535
uart_clps711x_init(void)536 static int __init uart_clps711x_init(void)
537 {
538 int ret;
539
540 #ifdef CONFIG_SERIAL_CLPS711X_CONSOLE
541 clps711x_uart.cons = &clps711x_console;
542 clps711x_console.data = &clps711x_uart;
543 #endif
544
545 ret = uart_register_driver(&clps711x_uart);
546 if (ret)
547 return ret;
548
549 return platform_driver_register(&clps711x_uart_platform);
550 }
551 module_init(uart_clps711x_init);
552
uart_clps711x_exit(void)553 static void __exit uart_clps711x_exit(void)
554 {
555 platform_driver_unregister(&clps711x_uart_platform);
556 uart_unregister_driver(&clps711x_uart);
557 }
558 module_exit(uart_clps711x_exit);
559
560 MODULE_AUTHOR("Deep Blue Solutions Ltd");
561 MODULE_DESCRIPTION("CLPS711X serial driver");
562 MODULE_LICENSE("GPL");
563