1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Texas Instruments ADS7950 SPI ADC driver
4 *
5 * Copyright 2016 David Lechner <david@lechnology.com>
6 *
7 * Based on iio/ad7923.c:
8 * Copyright 2011 Analog Devices Inc
9 * Copyright 2012 CS Systemes d'Information
10 *
11 * And also on hwmon/ads79xx.c
12 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
13 * Nishanth Menon
14 */
15
16 #include <linux/acpi.h>
17 #include <linux/bitops.h>
18 #include <linux/device.h>
19 #include <linux/err.h>
20 #include <linux/gpio/driver.h>
21 #include <linux/interrupt.h>
22 #include <linux/kernel.h>
23 #include <linux/module.h>
24 #include <linux/regulator/consumer.h>
25 #include <linux/slab.h>
26 #include <linux/spi/spi.h>
27
28 #include <linux/iio/buffer.h>
29 #include <linux/iio/iio.h>
30 #include <linux/iio/sysfs.h>
31 #include <linux/iio/trigger_consumer.h>
32 #include <linux/iio/triggered_buffer.h>
33
34 /*
35 * In case of ACPI, we use the 5000 mV as default for the reference pin.
36 * Device tree users encode that via the vref-supply regulator.
37 */
38 #define TI_ADS7950_VA_MV_ACPI_DEFAULT 5000
39
40 #define TI_ADS7950_CR_GPIO BIT(14)
41 #define TI_ADS7950_CR_MANUAL BIT(12)
42 #define TI_ADS7950_CR_WRITE BIT(11)
43 #define TI_ADS7950_CR_CHAN(ch) ((ch) << 7)
44 #define TI_ADS7950_CR_RANGE_5V BIT(6)
45 #define TI_ADS7950_CR_GPIO_DATA BIT(4)
46
47 #define TI_ADS7950_MAX_CHAN 16
48 #define TI_ADS7950_NUM_GPIOS 4
49
50 #define TI_ADS7950_TIMESTAMP_SIZE (sizeof(int64_t) / sizeof(__be16))
51
52 /* val = value, dec = left shift, bits = number of bits of the mask */
53 #define TI_ADS7950_EXTRACT(val, dec, bits) \
54 (((val) >> (dec)) & ((1 << (bits)) - 1))
55
56 #define TI_ADS7950_MAN_CMD(cmd) (TI_ADS7950_CR_MANUAL | (cmd))
57 #define TI_ADS7950_GPIO_CMD(cmd) (TI_ADS7950_CR_GPIO | (cmd))
58
59 /* Manual mode configuration */
60 #define TI_ADS7950_MAN_CMD_SETTINGS(st) \
61 (TI_ADS7950_MAN_CMD(TI_ADS7950_CR_WRITE | st->cmd_settings_bitmask))
62 /* GPIO mode configuration */
63 #define TI_ADS7950_GPIO_CMD_SETTINGS(st) \
64 (TI_ADS7950_GPIO_CMD(st->gpio_cmd_settings_bitmask))
65
66 struct ti_ads7950_state {
67 struct spi_device *spi;
68 struct spi_transfer ring_xfer;
69 struct spi_transfer scan_single_xfer[3];
70 struct spi_message ring_msg;
71 struct spi_message scan_single_msg;
72
73 /* Lock to protect the spi xfer buffers */
74 struct mutex slock;
75 struct gpio_chip chip;
76
77 struct regulator *reg;
78 unsigned int vref_mv;
79
80 /*
81 * Bitmask of lower 7 bits used for configuration
82 * These bits only can be written when TI_ADS7950_CR_WRITE
83 * is set, otherwise it retains its original state.
84 * [0-3] GPIO signal
85 * [4] Set following frame to return GPIO signal values
86 * [5] Powers down device
87 * [6] Sets Vref range1(2.5v) or range2(5v)
88 *
89 * Bits present on Manual/Auto1/Auto2 commands
90 */
91 unsigned int cmd_settings_bitmask;
92
93 /*
94 * Bitmask of GPIO command
95 * [0-3] GPIO direction
96 * [4-6] Different GPIO alarm mode configurations
97 * [7] GPIO 2 as device range input
98 * [8] GPIO 3 as device power down input
99 * [9] Reset all registers
100 * [10-11] N/A
101 */
102 unsigned int gpio_cmd_settings_bitmask;
103
104 /*
105 * DMA (thus cache coherency maintenance) may require the
106 * transfer buffers to live in their own cache lines.
107 */
108 u16 rx_buf[TI_ADS7950_MAX_CHAN + 2 + TI_ADS7950_TIMESTAMP_SIZE]
109 __aligned(IIO_DMA_MINALIGN);
110 u16 tx_buf[TI_ADS7950_MAX_CHAN + 2];
111 u16 single_tx;
112 u16 single_rx;
113
114 };
115
116 struct ti_ads7950_chip_info {
117 const struct iio_chan_spec *channels;
118 unsigned int num_channels;
119 };
120
121 enum ti_ads7950_id {
122 TI_ADS7950,
123 TI_ADS7951,
124 TI_ADS7952,
125 TI_ADS7953,
126 TI_ADS7954,
127 TI_ADS7955,
128 TI_ADS7956,
129 TI_ADS7957,
130 TI_ADS7958,
131 TI_ADS7959,
132 TI_ADS7960,
133 TI_ADS7961,
134 };
135
136 #define TI_ADS7950_V_CHAN(index, bits) \
137 { \
138 .type = IIO_VOLTAGE, \
139 .indexed = 1, \
140 .channel = index, \
141 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
142 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
143 .address = index, \
144 .datasheet_name = "CH##index", \
145 .scan_index = index, \
146 .scan_type = { \
147 .sign = 'u', \
148 .realbits = bits, \
149 .storagebits = 16, \
150 .shift = 12 - (bits), \
151 .endianness = IIO_CPU, \
152 }, \
153 }
154
155 #define DECLARE_TI_ADS7950_4_CHANNELS(name, bits) \
156 const struct iio_chan_spec name ## _channels[] = { \
157 TI_ADS7950_V_CHAN(0, bits), \
158 TI_ADS7950_V_CHAN(1, bits), \
159 TI_ADS7950_V_CHAN(2, bits), \
160 TI_ADS7950_V_CHAN(3, bits), \
161 IIO_CHAN_SOFT_TIMESTAMP(4), \
162 }
163
164 #define DECLARE_TI_ADS7950_8_CHANNELS(name, bits) \
165 const struct iio_chan_spec name ## _channels[] = { \
166 TI_ADS7950_V_CHAN(0, bits), \
167 TI_ADS7950_V_CHAN(1, bits), \
168 TI_ADS7950_V_CHAN(2, bits), \
169 TI_ADS7950_V_CHAN(3, bits), \
170 TI_ADS7950_V_CHAN(4, bits), \
171 TI_ADS7950_V_CHAN(5, bits), \
172 TI_ADS7950_V_CHAN(6, bits), \
173 TI_ADS7950_V_CHAN(7, bits), \
174 IIO_CHAN_SOFT_TIMESTAMP(8), \
175 }
176
177 #define DECLARE_TI_ADS7950_12_CHANNELS(name, bits) \
178 const struct iio_chan_spec name ## _channels[] = { \
179 TI_ADS7950_V_CHAN(0, bits), \
180 TI_ADS7950_V_CHAN(1, bits), \
181 TI_ADS7950_V_CHAN(2, bits), \
182 TI_ADS7950_V_CHAN(3, bits), \
183 TI_ADS7950_V_CHAN(4, bits), \
184 TI_ADS7950_V_CHAN(5, bits), \
185 TI_ADS7950_V_CHAN(6, bits), \
186 TI_ADS7950_V_CHAN(7, bits), \
187 TI_ADS7950_V_CHAN(8, bits), \
188 TI_ADS7950_V_CHAN(9, bits), \
189 TI_ADS7950_V_CHAN(10, bits), \
190 TI_ADS7950_V_CHAN(11, bits), \
191 IIO_CHAN_SOFT_TIMESTAMP(12), \
192 }
193
194 #define DECLARE_TI_ADS7950_16_CHANNELS(name, bits) \
195 const struct iio_chan_spec name ## _channels[] = { \
196 TI_ADS7950_V_CHAN(0, bits), \
197 TI_ADS7950_V_CHAN(1, bits), \
198 TI_ADS7950_V_CHAN(2, bits), \
199 TI_ADS7950_V_CHAN(3, bits), \
200 TI_ADS7950_V_CHAN(4, bits), \
201 TI_ADS7950_V_CHAN(5, bits), \
202 TI_ADS7950_V_CHAN(6, bits), \
203 TI_ADS7950_V_CHAN(7, bits), \
204 TI_ADS7950_V_CHAN(8, bits), \
205 TI_ADS7950_V_CHAN(9, bits), \
206 TI_ADS7950_V_CHAN(10, bits), \
207 TI_ADS7950_V_CHAN(11, bits), \
208 TI_ADS7950_V_CHAN(12, bits), \
209 TI_ADS7950_V_CHAN(13, bits), \
210 TI_ADS7950_V_CHAN(14, bits), \
211 TI_ADS7950_V_CHAN(15, bits), \
212 IIO_CHAN_SOFT_TIMESTAMP(16), \
213 }
214
215 static DECLARE_TI_ADS7950_4_CHANNELS(ti_ads7950, 12);
216 static DECLARE_TI_ADS7950_8_CHANNELS(ti_ads7951, 12);
217 static DECLARE_TI_ADS7950_12_CHANNELS(ti_ads7952, 12);
218 static DECLARE_TI_ADS7950_16_CHANNELS(ti_ads7953, 12);
219 static DECLARE_TI_ADS7950_4_CHANNELS(ti_ads7954, 10);
220 static DECLARE_TI_ADS7950_8_CHANNELS(ti_ads7955, 10);
221 static DECLARE_TI_ADS7950_12_CHANNELS(ti_ads7956, 10);
222 static DECLARE_TI_ADS7950_16_CHANNELS(ti_ads7957, 10);
223 static DECLARE_TI_ADS7950_4_CHANNELS(ti_ads7958, 8);
224 static DECLARE_TI_ADS7950_8_CHANNELS(ti_ads7959, 8);
225 static DECLARE_TI_ADS7950_12_CHANNELS(ti_ads7960, 8);
226 static DECLARE_TI_ADS7950_16_CHANNELS(ti_ads7961, 8);
227
228 static const struct ti_ads7950_chip_info ti_ads7950_chip_info[] = {
229 [TI_ADS7950] = {
230 .channels = ti_ads7950_channels,
231 .num_channels = ARRAY_SIZE(ti_ads7950_channels),
232 },
233 [TI_ADS7951] = {
234 .channels = ti_ads7951_channels,
235 .num_channels = ARRAY_SIZE(ti_ads7951_channels),
236 },
237 [TI_ADS7952] = {
238 .channels = ti_ads7952_channels,
239 .num_channels = ARRAY_SIZE(ti_ads7952_channels),
240 },
241 [TI_ADS7953] = {
242 .channels = ti_ads7953_channels,
243 .num_channels = ARRAY_SIZE(ti_ads7953_channels),
244 },
245 [TI_ADS7954] = {
246 .channels = ti_ads7954_channels,
247 .num_channels = ARRAY_SIZE(ti_ads7954_channels),
248 },
249 [TI_ADS7955] = {
250 .channels = ti_ads7955_channels,
251 .num_channels = ARRAY_SIZE(ti_ads7955_channels),
252 },
253 [TI_ADS7956] = {
254 .channels = ti_ads7956_channels,
255 .num_channels = ARRAY_SIZE(ti_ads7956_channels),
256 },
257 [TI_ADS7957] = {
258 .channels = ti_ads7957_channels,
259 .num_channels = ARRAY_SIZE(ti_ads7957_channels),
260 },
261 [TI_ADS7958] = {
262 .channels = ti_ads7958_channels,
263 .num_channels = ARRAY_SIZE(ti_ads7958_channels),
264 },
265 [TI_ADS7959] = {
266 .channels = ti_ads7959_channels,
267 .num_channels = ARRAY_SIZE(ti_ads7959_channels),
268 },
269 [TI_ADS7960] = {
270 .channels = ti_ads7960_channels,
271 .num_channels = ARRAY_SIZE(ti_ads7960_channels),
272 },
273 [TI_ADS7961] = {
274 .channels = ti_ads7961_channels,
275 .num_channels = ARRAY_SIZE(ti_ads7961_channels),
276 },
277 };
278
279 /*
280 * ti_ads7950_update_scan_mode() setup the spi transfer buffer for the new
281 * scan mask
282 */
ti_ads7950_update_scan_mode(struct iio_dev * indio_dev,const unsigned long * active_scan_mask)283 static int ti_ads7950_update_scan_mode(struct iio_dev *indio_dev,
284 const unsigned long *active_scan_mask)
285 {
286 struct ti_ads7950_state *st = iio_priv(indio_dev);
287 int i, cmd, len;
288
289 len = 0;
290 for_each_set_bit(i, active_scan_mask, indio_dev->num_channels) {
291 cmd = TI_ADS7950_MAN_CMD(TI_ADS7950_CR_CHAN(i));
292 st->tx_buf[len++] = cmd;
293 }
294
295 /* Data for the 1st channel is not returned until the 3rd transfer */
296 st->tx_buf[len++] = 0;
297 st->tx_buf[len++] = 0;
298
299 st->ring_xfer.len = len * 2;
300
301 return 0;
302 }
303
ti_ads7950_trigger_handler(int irq,void * p)304 static irqreturn_t ti_ads7950_trigger_handler(int irq, void *p)
305 {
306 struct iio_poll_func *pf = p;
307 struct iio_dev *indio_dev = pf->indio_dev;
308 struct ti_ads7950_state *st = iio_priv(indio_dev);
309 int ret;
310
311 mutex_lock(&st->slock);
312 ret = spi_sync(st->spi, &st->ring_msg);
313 if (ret < 0)
314 goto out;
315
316 iio_push_to_buffers_with_timestamp(indio_dev, &st->rx_buf[2],
317 iio_get_time_ns(indio_dev));
318
319 out:
320 mutex_unlock(&st->slock);
321 iio_trigger_notify_done(indio_dev->trig);
322
323 return IRQ_HANDLED;
324 }
325
ti_ads7950_scan_direct(struct iio_dev * indio_dev,unsigned int ch)326 static int ti_ads7950_scan_direct(struct iio_dev *indio_dev, unsigned int ch)
327 {
328 struct ti_ads7950_state *st = iio_priv(indio_dev);
329 int ret, cmd;
330
331 mutex_lock(&st->slock);
332 cmd = TI_ADS7950_MAN_CMD(TI_ADS7950_CR_CHAN(ch));
333 st->single_tx = cmd;
334
335 ret = spi_sync(st->spi, &st->scan_single_msg);
336 if (ret)
337 goto out;
338
339 ret = st->single_rx;
340
341 out:
342 mutex_unlock(&st->slock);
343
344 return ret;
345 }
346
ti_ads7950_get_range(struct ti_ads7950_state * st)347 static int ti_ads7950_get_range(struct ti_ads7950_state *st)
348 {
349 int vref;
350
351 if (st->vref_mv) {
352 vref = st->vref_mv;
353 } else {
354 vref = regulator_get_voltage(st->reg);
355 if (vref < 0)
356 return vref;
357
358 vref /= 1000;
359 }
360
361 if (st->cmd_settings_bitmask & TI_ADS7950_CR_RANGE_5V)
362 vref *= 2;
363
364 return vref;
365 }
366
ti_ads7950_read_raw(struct iio_dev * indio_dev,struct iio_chan_spec const * chan,int * val,int * val2,long m)367 static int ti_ads7950_read_raw(struct iio_dev *indio_dev,
368 struct iio_chan_spec const *chan,
369 int *val, int *val2, long m)
370 {
371 struct ti_ads7950_state *st = iio_priv(indio_dev);
372 int ret;
373
374 switch (m) {
375 case IIO_CHAN_INFO_RAW:
376 ret = ti_ads7950_scan_direct(indio_dev, chan->address);
377 if (ret < 0)
378 return ret;
379
380 if (chan->address != TI_ADS7950_EXTRACT(ret, 12, 4))
381 return -EIO;
382
383 *val = TI_ADS7950_EXTRACT(ret, chan->scan_type.shift,
384 chan->scan_type.realbits);
385
386 return IIO_VAL_INT;
387 case IIO_CHAN_INFO_SCALE:
388 ret = ti_ads7950_get_range(st);
389 if (ret < 0)
390 return ret;
391
392 *val = ret;
393 *val2 = (1 << chan->scan_type.realbits) - 1;
394
395 return IIO_VAL_FRACTIONAL;
396 }
397
398 return -EINVAL;
399 }
400
401 static const struct iio_info ti_ads7950_info = {
402 .read_raw = &ti_ads7950_read_raw,
403 .update_scan_mode = ti_ads7950_update_scan_mode,
404 };
405
ti_ads7950_set(struct gpio_chip * chip,unsigned int offset,int value)406 static void ti_ads7950_set(struct gpio_chip *chip, unsigned int offset,
407 int value)
408 {
409 struct ti_ads7950_state *st = gpiochip_get_data(chip);
410
411 mutex_lock(&st->slock);
412
413 if (value)
414 st->cmd_settings_bitmask |= BIT(offset);
415 else
416 st->cmd_settings_bitmask &= ~BIT(offset);
417
418 st->single_tx = TI_ADS7950_MAN_CMD_SETTINGS(st);
419 spi_sync(st->spi, &st->scan_single_msg);
420
421 mutex_unlock(&st->slock);
422 }
423
ti_ads7950_get(struct gpio_chip * chip,unsigned int offset)424 static int ti_ads7950_get(struct gpio_chip *chip, unsigned int offset)
425 {
426 struct ti_ads7950_state *st = gpiochip_get_data(chip);
427 int ret;
428
429 mutex_lock(&st->slock);
430
431 /* If set as output, return the output */
432 if (st->gpio_cmd_settings_bitmask & BIT(offset)) {
433 ret = st->cmd_settings_bitmask & BIT(offset);
434 goto out;
435 }
436
437 /* GPIO data bit sets SDO bits 12-15 to GPIO input */
438 st->cmd_settings_bitmask |= TI_ADS7950_CR_GPIO_DATA;
439 st->single_tx = TI_ADS7950_MAN_CMD_SETTINGS(st);
440 ret = spi_sync(st->spi, &st->scan_single_msg);
441 if (ret)
442 goto out;
443
444 ret = ((st->single_rx >> 12) & BIT(offset)) ? 1 : 0;
445
446 /* Revert back to original settings */
447 st->cmd_settings_bitmask &= ~TI_ADS7950_CR_GPIO_DATA;
448 st->single_tx = TI_ADS7950_MAN_CMD_SETTINGS(st);
449 ret = spi_sync(st->spi, &st->scan_single_msg);
450 if (ret)
451 goto out;
452
453 out:
454 mutex_unlock(&st->slock);
455
456 return ret;
457 }
458
ti_ads7950_get_direction(struct gpio_chip * chip,unsigned int offset)459 static int ti_ads7950_get_direction(struct gpio_chip *chip,
460 unsigned int offset)
461 {
462 struct ti_ads7950_state *st = gpiochip_get_data(chip);
463
464 /* Bitmask is inverted from GPIO framework 0=input/1=output */
465 return !(st->gpio_cmd_settings_bitmask & BIT(offset));
466 }
467
_ti_ads7950_set_direction(struct gpio_chip * chip,int offset,int input)468 static int _ti_ads7950_set_direction(struct gpio_chip *chip, int offset,
469 int input)
470 {
471 struct ti_ads7950_state *st = gpiochip_get_data(chip);
472 int ret = 0;
473
474 mutex_lock(&st->slock);
475
476 /* Only change direction if needed */
477 if (input && (st->gpio_cmd_settings_bitmask & BIT(offset)))
478 st->gpio_cmd_settings_bitmask &= ~BIT(offset);
479 else if (!input && !(st->gpio_cmd_settings_bitmask & BIT(offset)))
480 st->gpio_cmd_settings_bitmask |= BIT(offset);
481 else
482 goto out;
483
484 st->single_tx = TI_ADS7950_GPIO_CMD_SETTINGS(st);
485 ret = spi_sync(st->spi, &st->scan_single_msg);
486
487 out:
488 mutex_unlock(&st->slock);
489
490 return ret;
491 }
492
ti_ads7950_direction_input(struct gpio_chip * chip,unsigned int offset)493 static int ti_ads7950_direction_input(struct gpio_chip *chip,
494 unsigned int offset)
495 {
496 return _ti_ads7950_set_direction(chip, offset, 1);
497 }
498
ti_ads7950_direction_output(struct gpio_chip * chip,unsigned int offset,int value)499 static int ti_ads7950_direction_output(struct gpio_chip *chip,
500 unsigned int offset, int value)
501 {
502 ti_ads7950_set(chip, offset, value);
503
504 return _ti_ads7950_set_direction(chip, offset, 0);
505 }
506
ti_ads7950_init_hw(struct ti_ads7950_state * st)507 static int ti_ads7950_init_hw(struct ti_ads7950_state *st)
508 {
509 int ret = 0;
510
511 mutex_lock(&st->slock);
512
513 /* Settings for Manual/Auto1/Auto2 commands */
514 /* Default to 5v ref */
515 st->cmd_settings_bitmask = TI_ADS7950_CR_RANGE_5V;
516 st->single_tx = TI_ADS7950_MAN_CMD_SETTINGS(st);
517 ret = spi_sync(st->spi, &st->scan_single_msg);
518 if (ret)
519 goto out;
520
521 /* Settings for GPIO command */
522 st->gpio_cmd_settings_bitmask = 0x0;
523 st->single_tx = TI_ADS7950_GPIO_CMD_SETTINGS(st);
524 ret = spi_sync(st->spi, &st->scan_single_msg);
525
526 out:
527 mutex_unlock(&st->slock);
528
529 return ret;
530 }
531
ti_ads7950_probe(struct spi_device * spi)532 static int ti_ads7950_probe(struct spi_device *spi)
533 {
534 struct ti_ads7950_state *st;
535 struct iio_dev *indio_dev;
536 const struct ti_ads7950_chip_info *info;
537 int ret;
538
539 spi->bits_per_word = 16;
540 spi->mode |= SPI_CS_WORD;
541 ret = spi_setup(spi);
542 if (ret < 0) {
543 dev_err(&spi->dev, "Error in spi setup\n");
544 return ret;
545 }
546
547 indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
548 if (!indio_dev)
549 return -ENOMEM;
550
551 st = iio_priv(indio_dev);
552
553 spi_set_drvdata(spi, indio_dev);
554
555 st->spi = spi;
556
557 info = &ti_ads7950_chip_info[spi_get_device_id(spi)->driver_data];
558
559 indio_dev->name = spi_get_device_id(spi)->name;
560 indio_dev->modes = INDIO_DIRECT_MODE;
561 indio_dev->channels = info->channels;
562 indio_dev->num_channels = info->num_channels;
563 indio_dev->info = &ti_ads7950_info;
564
565 /* build spi ring message */
566 spi_message_init(&st->ring_msg);
567
568 st->ring_xfer.tx_buf = &st->tx_buf[0];
569 st->ring_xfer.rx_buf = &st->rx_buf[0];
570 /* len will be set later */
571
572 spi_message_add_tail(&st->ring_xfer, &st->ring_msg);
573
574 /*
575 * Setup default message. The sample is read at the end of the first
576 * transfer, then it takes one full cycle to convert the sample and one
577 * more cycle to send the value. The conversion process is driven by
578 * the SPI clock, which is why we have 3 transfers. The middle one is
579 * just dummy data sent while the chip is converting the sample that
580 * was read at the end of the first transfer.
581 */
582
583 st->scan_single_xfer[0].tx_buf = &st->single_tx;
584 st->scan_single_xfer[0].len = 2;
585 st->scan_single_xfer[0].cs_change = 1;
586 st->scan_single_xfer[1].tx_buf = &st->single_tx;
587 st->scan_single_xfer[1].len = 2;
588 st->scan_single_xfer[1].cs_change = 1;
589 st->scan_single_xfer[2].rx_buf = &st->single_rx;
590 st->scan_single_xfer[2].len = 2;
591
592 spi_message_init_with_transfers(&st->scan_single_msg,
593 st->scan_single_xfer, 3);
594
595 /* Use hard coded value for reference voltage in ACPI case */
596 if (ACPI_COMPANION(&spi->dev))
597 st->vref_mv = TI_ADS7950_VA_MV_ACPI_DEFAULT;
598
599 mutex_init(&st->slock);
600
601 st->reg = devm_regulator_get(&spi->dev, "vref");
602 if (IS_ERR(st->reg)) {
603 ret = dev_err_probe(&spi->dev, PTR_ERR(st->reg),
604 "Failed to get regulator \"vref\"\n");
605 goto error_destroy_mutex;
606 }
607
608 ret = regulator_enable(st->reg);
609 if (ret) {
610 dev_err(&spi->dev, "Failed to enable regulator \"vref\"\n");
611 goto error_destroy_mutex;
612 }
613
614 ret = iio_triggered_buffer_setup(indio_dev, NULL,
615 &ti_ads7950_trigger_handler, NULL);
616 if (ret) {
617 dev_err(&spi->dev, "Failed to setup triggered buffer\n");
618 goto error_disable_reg;
619 }
620
621 ret = ti_ads7950_init_hw(st);
622 if (ret) {
623 dev_err(&spi->dev, "Failed to init adc chip\n");
624 goto error_cleanup_ring;
625 }
626
627 ret = iio_device_register(indio_dev);
628 if (ret) {
629 dev_err(&spi->dev, "Failed to register iio device\n");
630 goto error_cleanup_ring;
631 }
632
633 /* Add GPIO chip */
634 st->chip.label = dev_name(&st->spi->dev);
635 st->chip.parent = &st->spi->dev;
636 st->chip.owner = THIS_MODULE;
637 st->chip.can_sleep = true;
638 st->chip.base = -1;
639 st->chip.ngpio = TI_ADS7950_NUM_GPIOS;
640 st->chip.get_direction = ti_ads7950_get_direction;
641 st->chip.direction_input = ti_ads7950_direction_input;
642 st->chip.direction_output = ti_ads7950_direction_output;
643 st->chip.get = ti_ads7950_get;
644 st->chip.set = ti_ads7950_set;
645
646 ret = gpiochip_add_data(&st->chip, st);
647 if (ret) {
648 dev_err(&spi->dev, "Failed to init GPIOs\n");
649 goto error_iio_device;
650 }
651
652 return 0;
653
654 error_iio_device:
655 iio_device_unregister(indio_dev);
656 error_cleanup_ring:
657 iio_triggered_buffer_cleanup(indio_dev);
658 error_disable_reg:
659 regulator_disable(st->reg);
660 error_destroy_mutex:
661 mutex_destroy(&st->slock);
662
663 return ret;
664 }
665
ti_ads7950_remove(struct spi_device * spi)666 static void ti_ads7950_remove(struct spi_device *spi)
667 {
668 struct iio_dev *indio_dev = spi_get_drvdata(spi);
669 struct ti_ads7950_state *st = iio_priv(indio_dev);
670
671 gpiochip_remove(&st->chip);
672 iio_device_unregister(indio_dev);
673 iio_triggered_buffer_cleanup(indio_dev);
674 regulator_disable(st->reg);
675 mutex_destroy(&st->slock);
676 }
677
678 static const struct spi_device_id ti_ads7950_id[] = {
679 { "ads7950", TI_ADS7950 },
680 { "ads7951", TI_ADS7951 },
681 { "ads7952", TI_ADS7952 },
682 { "ads7953", TI_ADS7953 },
683 { "ads7954", TI_ADS7954 },
684 { "ads7955", TI_ADS7955 },
685 { "ads7956", TI_ADS7956 },
686 { "ads7957", TI_ADS7957 },
687 { "ads7958", TI_ADS7958 },
688 { "ads7959", TI_ADS7959 },
689 { "ads7960", TI_ADS7960 },
690 { "ads7961", TI_ADS7961 },
691 { }
692 };
693 MODULE_DEVICE_TABLE(spi, ti_ads7950_id);
694
695 static const struct of_device_id ads7950_of_table[] = {
696 { .compatible = "ti,ads7950", .data = &ti_ads7950_chip_info[TI_ADS7950] },
697 { .compatible = "ti,ads7951", .data = &ti_ads7950_chip_info[TI_ADS7951] },
698 { .compatible = "ti,ads7952", .data = &ti_ads7950_chip_info[TI_ADS7952] },
699 { .compatible = "ti,ads7953", .data = &ti_ads7950_chip_info[TI_ADS7953] },
700 { .compatible = "ti,ads7954", .data = &ti_ads7950_chip_info[TI_ADS7954] },
701 { .compatible = "ti,ads7955", .data = &ti_ads7950_chip_info[TI_ADS7955] },
702 { .compatible = "ti,ads7956", .data = &ti_ads7950_chip_info[TI_ADS7956] },
703 { .compatible = "ti,ads7957", .data = &ti_ads7950_chip_info[TI_ADS7957] },
704 { .compatible = "ti,ads7958", .data = &ti_ads7950_chip_info[TI_ADS7958] },
705 { .compatible = "ti,ads7959", .data = &ti_ads7950_chip_info[TI_ADS7959] },
706 { .compatible = "ti,ads7960", .data = &ti_ads7950_chip_info[TI_ADS7960] },
707 { .compatible = "ti,ads7961", .data = &ti_ads7950_chip_info[TI_ADS7961] },
708 { },
709 };
710 MODULE_DEVICE_TABLE(of, ads7950_of_table);
711
712 static struct spi_driver ti_ads7950_driver = {
713 .driver = {
714 .name = "ads7950",
715 .of_match_table = ads7950_of_table,
716 },
717 .probe = ti_ads7950_probe,
718 .remove = ti_ads7950_remove,
719 .id_table = ti_ads7950_id,
720 };
721 module_spi_driver(ti_ads7950_driver);
722
723 MODULE_AUTHOR("David Lechner <david@lechnology.com>");
724 MODULE_DESCRIPTION("TI TI_ADS7950 ADC");
725 MODULE_LICENSE("GPL v2");
726