1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
4 * Copyright (C) 2008 Markus Plessing <plessing@ems-wuensche.com>
5 * Copyright (C) 2008 Sebastian Haas <haas@ems-wuensche.com>
6 * Copyright (C) 2023 EMS Dr. Thomas Wuensche
7 */
8
9 #include <linux/kernel.h>
10 #include <linux/module.h>
11 #include <linux/interrupt.h>
12 #include <linux/netdevice.h>
13 #include <linux/delay.h>
14 #include <linux/slab.h>
15 #include <linux/pci.h>
16 #include <linux/can/dev.h>
17 #include <linux/io.h>
18
19 #include "sja1000.h"
20
21 #define DRV_NAME "ems_pci"
22
23 MODULE_AUTHOR("Sebastian Haas <support@ems-wuensche.com>");
24 MODULE_AUTHOR("Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>");
25 MODULE_DESCRIPTION("Socket-CAN driver for EMS CPC-PCI/PCIe/104P CAN cards");
26 MODULE_LICENSE("GPL v2");
27
28 #define EMS_PCI_V1_MAX_CHAN 2
29 #define EMS_PCI_V2_MAX_CHAN 4
30 #define EMS_PCI_V3_MAX_CHAN 4
31 #define EMS_PCI_MAX_CHAN EMS_PCI_V2_MAX_CHAN
32
33 struct ems_pci_card {
34 int version;
35 int channels;
36
37 struct pci_dev *pci_dev;
38 struct net_device *net_dev[EMS_PCI_MAX_CHAN];
39
40 void __iomem *conf_addr;
41 void __iomem *base_addr;
42 };
43
44 #define EMS_PCI_CAN_CLOCK (16000000 / 2)
45
46 /* Register definitions and descriptions are from LinCAN 0.3.3.
47 *
48 * PSB4610 PITA-2 bridge control registers
49 */
50 #define PITA2_ICR 0x00 /* Interrupt Control Register */
51 #define PITA2_ICR_INT0 0x00000002 /* [RC] INT0 Active/Clear */
52 #define PITA2_ICR_INT0_EN 0x00020000 /* [RW] Enable INT0 */
53
54 #define PITA2_MISC 0x1c /* Miscellaneous Register */
55 #define PITA2_MISC_CONFIG 0x04000000 /* Multiplexed parallel interface */
56
57 /* Register definitions for the PLX 9030
58 */
59 #define PLX_ICSR 0x4c /* Interrupt Control/Status register */
60 #define PLX_ICSR_LINTI1_ENA 0x0001 /* LINTi1 Enable */
61 #define PLX_ICSR_PCIINT_ENA 0x0040 /* PCI Interrupt Enable */
62 #define PLX_ICSR_LINTI1_CLR 0x0400 /* Local Edge Triggerable Interrupt Clear */
63 #define PLX_ICSR_ENA_CLR (PLX_ICSR_LINTI1_ENA | PLX_ICSR_PCIINT_ENA | \
64 PLX_ICSR_LINTI1_CLR)
65
66 /* Register definitions for the ASIX99100
67 */
68 #define ASIX_LINTSR 0x28 /* Interrupt Control/Status register */
69 #define ASIX_LINTSR_INT0AC BIT(0) /* Writing 1 enables or clears interrupt */
70
71 #define ASIX_LIEMR 0x24 /* Local Interrupt Enable / Miscellaneous Register */
72 #define ASIX_LIEMR_L0EINTEN BIT(16) /* Local INT0 input assertion enable */
73 #define ASIX_LIEMR_LRST BIT(14) /* Local Reset assert */
74
75 /* The board configuration is probably following:
76 * RX1 is connected to ground.
77 * TX1 is not connected.
78 * CLKO is not connected.
79 * Setting the OCR register to 0xDA is a good idea.
80 * This means normal output mode, push-pull and the correct polarity.
81 */
82 #define EMS_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
83
84 /* In the CDR register, you should set CBP to 1.
85 * You will probably also want to set the clock divider value to 7
86 * (meaning direct oscillator output) because the second SJA1000 chip
87 * is driven by the first one CLKOUT output.
88 */
89 #define EMS_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
90
91 #define EMS_PCI_V1_BASE_BAR 1
92 #define EMS_PCI_V1_CONF_BAR 0
93 #define EMS_PCI_V1_CONF_SIZE 4096 /* size of PITA control area */
94 #define EMS_PCI_V1_CAN_BASE_OFFSET 0x400 /* offset where the controllers start */
95 #define EMS_PCI_V1_CAN_CTRL_SIZE 0x200 /* memory size for each controller */
96
97 #define EMS_PCI_V2_BASE_BAR 2
98 #define EMS_PCI_V2_CONF_BAR 0
99 #define EMS_PCI_V2_CONF_SIZE 128 /* size of PLX control area */
100 #define EMS_PCI_V2_CAN_BASE_OFFSET 0x400 /* offset where the controllers start */
101 #define EMS_PCI_V2_CAN_CTRL_SIZE 0x200 /* memory size for each controller */
102
103 #define EMS_PCI_V3_BASE_BAR 0
104 #define EMS_PCI_V3_CONF_BAR 5
105 #define EMS_PCI_V3_CONF_SIZE 128 /* size of ASIX control area */
106 #define EMS_PCI_V3_CAN_BASE_OFFSET 0x00 /* offset where the controllers starts */
107 #define EMS_PCI_V3_CAN_CTRL_SIZE 0x100 /* memory size for each controller */
108
109 #define EMS_PCI_BASE_SIZE 4096 /* size of controller area */
110
111 #define PCI_SUBDEVICE_ID_EMS 0x4010
112
113 static const struct pci_device_id ems_pci_tbl[] = {
114 /* CPC-PCI v1 */
115 {PCI_VENDOR_ID_SIEMENS, 0x2104, PCI_ANY_ID, PCI_ANY_ID,},
116 /* CPC-PCI v2 */
117 {PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_PLX, 0x4000},
118 /* CPC-104P v2 */
119 {PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_PLX, 0x4002},
120 /* CPC-PCIe v3 */
121 {PCI_VENDOR_ID_ASIX, PCI_DEVICE_ID_ASIX_AX99100_LB, 0xa000, PCI_SUBDEVICE_ID_EMS},
122 {0,}
123 };
124 MODULE_DEVICE_TABLE(pci, ems_pci_tbl);
125
126 /* Helper to read internal registers from card logic (not CAN)
127 */
ems_pci_v1_readb(struct ems_pci_card * card,unsigned int port)128 static u8 ems_pci_v1_readb(struct ems_pci_card *card, unsigned int port)
129 {
130 return readb(card->base_addr + (port * 4));
131 }
132
ems_pci_v1_read_reg(const struct sja1000_priv * priv,int port)133 static u8 ems_pci_v1_read_reg(const struct sja1000_priv *priv, int port)
134 {
135 return readb(priv->reg_base + (port * 4));
136 }
137
ems_pci_v1_write_reg(const struct sja1000_priv * priv,int port,u8 val)138 static void ems_pci_v1_write_reg(const struct sja1000_priv *priv,
139 int port, u8 val)
140 {
141 writeb(val, priv->reg_base + (port * 4));
142 }
143
ems_pci_v1_post_irq(const struct sja1000_priv * priv)144 static void ems_pci_v1_post_irq(const struct sja1000_priv *priv)
145 {
146 struct ems_pci_card *card = priv->priv;
147
148 /* reset int flag of pita */
149 writel(PITA2_ICR_INT0_EN | PITA2_ICR_INT0,
150 card->conf_addr + PITA2_ICR);
151 }
152
ems_pci_v2_read_reg(const struct sja1000_priv * priv,int port)153 static u8 ems_pci_v2_read_reg(const struct sja1000_priv *priv, int port)
154 {
155 return readb(priv->reg_base + port);
156 }
157
ems_pci_v2_write_reg(const struct sja1000_priv * priv,int port,u8 val)158 static void ems_pci_v2_write_reg(const struct sja1000_priv *priv,
159 int port, u8 val)
160 {
161 writeb(val, priv->reg_base + port);
162 }
163
ems_pci_v2_post_irq(const struct sja1000_priv * priv)164 static void ems_pci_v2_post_irq(const struct sja1000_priv *priv)
165 {
166 struct ems_pci_card *card = priv->priv;
167
168 writel(PLX_ICSR_ENA_CLR, card->conf_addr + PLX_ICSR);
169 }
170
ems_pci_v3_read_reg(const struct sja1000_priv * priv,int port)171 static u8 ems_pci_v3_read_reg(const struct sja1000_priv *priv, int port)
172 {
173 return readb(priv->reg_base + port);
174 }
175
ems_pci_v3_write_reg(const struct sja1000_priv * priv,int port,u8 val)176 static void ems_pci_v3_write_reg(const struct sja1000_priv *priv,
177 int port, u8 val)
178 {
179 writeb(val, priv->reg_base + port);
180 }
181
ems_pci_v3_post_irq(const struct sja1000_priv * priv)182 static void ems_pci_v3_post_irq(const struct sja1000_priv *priv)
183 {
184 struct ems_pci_card *card = priv->priv;
185
186 writel(ASIX_LINTSR_INT0AC, card->conf_addr + ASIX_LINTSR);
187 }
188
189 /* Check if a CAN controller is present at the specified location
190 * by trying to set 'em into the PeliCAN mode
191 */
ems_pci_check_chan(const struct sja1000_priv * priv)192 static inline int ems_pci_check_chan(const struct sja1000_priv *priv)
193 {
194 unsigned char res;
195
196 /* Make sure SJA1000 is in reset mode */
197 priv->write_reg(priv, SJA1000_MOD, 1);
198
199 priv->write_reg(priv, SJA1000_CDR, CDR_PELICAN);
200
201 /* read reset-values */
202 res = priv->read_reg(priv, SJA1000_CDR);
203
204 if (res == CDR_PELICAN)
205 return 1;
206
207 return 0;
208 }
209
ems_pci_del_card(struct pci_dev * pdev)210 static void ems_pci_del_card(struct pci_dev *pdev)
211 {
212 struct ems_pci_card *card = pci_get_drvdata(pdev);
213 struct net_device *dev;
214 int i = 0;
215
216 for (i = 0; i < card->channels; i++) {
217 dev = card->net_dev[i];
218
219 if (!dev)
220 continue;
221
222 dev_info(&pdev->dev, "Removing %s.\n", dev->name);
223 unregister_sja1000dev(dev);
224 free_sja1000dev(dev);
225 }
226
227 if (card->base_addr)
228 pci_iounmap(card->pci_dev, card->base_addr);
229
230 if (card->conf_addr)
231 pci_iounmap(card->pci_dev, card->conf_addr);
232
233 kfree(card);
234
235 pci_disable_device(pdev);
236 }
237
ems_pci_card_reset(struct ems_pci_card * card)238 static void ems_pci_card_reset(struct ems_pci_card *card)
239 {
240 /* Request board reset */
241 writeb(0, card->base_addr);
242 }
243
244 /* Probe PCI device for EMS CAN signature and register each available
245 * CAN channel to SJA1000 Socket-CAN subsystem.
246 */
ems_pci_add_card(struct pci_dev * pdev,const struct pci_device_id * ent)247 static int ems_pci_add_card(struct pci_dev *pdev,
248 const struct pci_device_id *ent)
249 {
250 struct sja1000_priv *priv;
251 struct net_device *dev;
252 struct ems_pci_card *card;
253 int max_chan, conf_size, base_bar, conf_bar;
254 int err, i;
255
256 /* Enabling PCI device */
257 if (pci_enable_device(pdev) < 0) {
258 dev_err(&pdev->dev, "Enabling PCI device failed\n");
259 return -ENODEV;
260 }
261
262 /* Allocating card structures to hold addresses, ... */
263 card = kzalloc(sizeof(*card), GFP_KERNEL);
264 if (!card) {
265 pci_disable_device(pdev);
266 return -ENOMEM;
267 }
268
269 pci_set_drvdata(pdev, card);
270
271 card->pci_dev = pdev;
272
273 card->channels = 0;
274
275 if (pdev->vendor == PCI_VENDOR_ID_ASIX) {
276 card->version = 3; /* CPC-PCI v3 */
277 max_chan = EMS_PCI_V3_MAX_CHAN;
278 base_bar = EMS_PCI_V3_BASE_BAR;
279 conf_bar = EMS_PCI_V3_CONF_BAR;
280 conf_size = EMS_PCI_V3_CONF_SIZE;
281 } else if (pdev->vendor == PCI_VENDOR_ID_PLX) {
282 card->version = 2; /* CPC-PCI v2 */
283 max_chan = EMS_PCI_V2_MAX_CHAN;
284 base_bar = EMS_PCI_V2_BASE_BAR;
285 conf_bar = EMS_PCI_V2_CONF_BAR;
286 conf_size = EMS_PCI_V2_CONF_SIZE;
287 } else {
288 card->version = 1; /* CPC-PCI v1 */
289 max_chan = EMS_PCI_V1_MAX_CHAN;
290 base_bar = EMS_PCI_V1_BASE_BAR;
291 conf_bar = EMS_PCI_V1_CONF_BAR;
292 conf_size = EMS_PCI_V1_CONF_SIZE;
293 }
294
295 /* Remap configuration space and controller memory area */
296 card->conf_addr = pci_iomap(pdev, conf_bar, conf_size);
297 if (!card->conf_addr) {
298 err = -ENOMEM;
299 goto failure_cleanup;
300 }
301
302 card->base_addr = pci_iomap(pdev, base_bar, EMS_PCI_BASE_SIZE);
303 if (!card->base_addr) {
304 err = -ENOMEM;
305 goto failure_cleanup;
306 }
307
308 if (card->version == 1) {
309 /* Configure PITA-2 parallel interface (enable MUX) */
310 writel(PITA2_MISC_CONFIG, card->conf_addr + PITA2_MISC);
311
312 /* Check for unique EMS CAN signature */
313 if (ems_pci_v1_readb(card, 0) != 0x55 ||
314 ems_pci_v1_readb(card, 1) != 0xAA ||
315 ems_pci_v1_readb(card, 2) != 0x01 ||
316 ems_pci_v1_readb(card, 3) != 0xCB ||
317 ems_pci_v1_readb(card, 4) != 0x11) {
318 dev_err(&pdev->dev,
319 "Not EMS Dr. Thomas Wuensche interface\n");
320 err = -ENODEV;
321 goto failure_cleanup;
322 }
323 }
324
325 if (card->version == 3) {
326 /* ASIX chip asserts local reset to CAN controllers
327 * after bootup until it is deasserted
328 */
329 writel(readl(card->conf_addr + ASIX_LIEMR) & ~ASIX_LIEMR_LRST,
330 card->conf_addr + ASIX_LIEMR);
331 }
332
333 ems_pci_card_reset(card);
334
335 /* Detect available channels */
336 for (i = 0; i < max_chan; i++) {
337 dev = alloc_sja1000dev(0);
338 if (!dev) {
339 err = -ENOMEM;
340 goto failure_cleanup;
341 }
342
343 card->net_dev[i] = dev;
344 priv = netdev_priv(dev);
345 priv->priv = card;
346 priv->irq_flags = IRQF_SHARED;
347
348 dev->irq = pdev->irq;
349
350 if (card->version == 1) {
351 priv->read_reg = ems_pci_v1_read_reg;
352 priv->write_reg = ems_pci_v1_write_reg;
353 priv->post_irq = ems_pci_v1_post_irq;
354 priv->reg_base = card->base_addr + EMS_PCI_V1_CAN_BASE_OFFSET
355 + (i * EMS_PCI_V1_CAN_CTRL_SIZE);
356 } else if (card->version == 2) {
357 priv->read_reg = ems_pci_v2_read_reg;
358 priv->write_reg = ems_pci_v2_write_reg;
359 priv->post_irq = ems_pci_v2_post_irq;
360 priv->reg_base = card->base_addr + EMS_PCI_V2_CAN_BASE_OFFSET
361 + (i * EMS_PCI_V2_CAN_CTRL_SIZE);
362 } else {
363 priv->read_reg = ems_pci_v3_read_reg;
364 priv->write_reg = ems_pci_v3_write_reg;
365 priv->post_irq = ems_pci_v3_post_irq;
366 priv->reg_base = card->base_addr + EMS_PCI_V3_CAN_BASE_OFFSET
367 + (i * EMS_PCI_V3_CAN_CTRL_SIZE);
368 }
369
370 /* Check if channel is present */
371 if (ems_pci_check_chan(priv)) {
372 priv->can.clock.freq = EMS_PCI_CAN_CLOCK;
373 priv->ocr = EMS_PCI_OCR;
374 priv->cdr = EMS_PCI_CDR;
375
376 SET_NETDEV_DEV(dev, &pdev->dev);
377 dev->dev_id = i;
378
379 if (card->version == 1) {
380 /* reset int flag of pita */
381 writel(PITA2_ICR_INT0_EN | PITA2_ICR_INT0,
382 card->conf_addr + PITA2_ICR);
383 } else if (card->version == 2) {
384 /* enable IRQ in PLX 9030 */
385 writel(PLX_ICSR_ENA_CLR,
386 card->conf_addr + PLX_ICSR);
387 } else {
388 /* Enable IRQ in AX99100 */
389 writel(ASIX_LINTSR_INT0AC, card->conf_addr + ASIX_LINTSR);
390 /* Enable local INT0 input enable */
391 writel(readl(card->conf_addr + ASIX_LIEMR) | ASIX_LIEMR_L0EINTEN,
392 card->conf_addr + ASIX_LIEMR);
393 }
394
395 /* Register SJA1000 device */
396 err = register_sja1000dev(dev);
397 if (err) {
398 dev_err(&pdev->dev,
399 "Registering device failed: %pe\n",
400 ERR_PTR(err));
401 free_sja1000dev(dev);
402 goto failure_cleanup;
403 }
404
405 card->channels++;
406
407 dev_info(&pdev->dev, "Channel #%d at 0x%p, irq %d\n",
408 i + 1, priv->reg_base, dev->irq);
409 } else {
410 free_sja1000dev(dev);
411 }
412 }
413
414 return 0;
415
416 failure_cleanup:
417 dev_err(&pdev->dev, "Error: %d. Cleaning Up.\n", err);
418
419 ems_pci_del_card(pdev);
420
421 return err;
422 }
423
424 static struct pci_driver ems_pci_driver = {
425 .name = DRV_NAME,
426 .id_table = ems_pci_tbl,
427 .probe = ems_pci_add_card,
428 .remove = ems_pci_del_card,
429 };
430
431 module_pci_driver(ems_pci_driver);
432