1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /* Copyright(c) 2009-2010 Realtek Corporation.*/ 3 4 #ifndef __RTL8821AE_PWRSEQ_H__ 5 #define __RTL8821AE_PWRSEQ_H__ 6 7 #include "../pwrseqcmd.h" 8 #include "../btcoexist/halbt_precomp.h" 9 10 #define RTL8812_TRANS_CARDEMU_TO_ACT_STEPS 15 11 #define RTL8812_TRANS_ACT_TO_CARDEMU_STEPS 15 12 #define RTL8812_TRANS_CARDEMU_TO_SUS_STEPS 15 13 #define RTL8812_TRANS_SUS_TO_CARDEMU_STEPS 15 14 #define RTL8812_TRANS_CARDEMU_TO_PDN_STEPS 25 15 #define RTL8812_TRANS_PDN_TO_CARDEMU_STEPS 15 16 #define RTL8812_TRANS_ACT_TO_LPS_STEPS 15 17 #define RTL8812_TRANS_LPS_TO_ACT_STEPS 15 18 #define RTL8812_TRANS_END_STEPS 1 19 20 /* The following macros have the following format: 21 * { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value 22 * comments }, 23 */ 24 #define RTL8812_TRANS_CARDEMU_TO_ACT \ 25 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 26 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0 \ 27 /* disable SW LPS 0x04[10]=0*/}, \ 28 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 29 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1 \ 30 /* wait till 0x04[17] = 1 power ready*/}, \ 31 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 32 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0 \ 33 /* disable HWPDN 0x04[15]=0*/}, \ 34 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 35 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, 0 \ 36 /* disable WL suspend*/}, \ 37 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 38 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0 \ 39 /* polling until return 0*/}, \ 40 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 41 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0}, 42 43 #define RTL8812_TRANS_ACT_TO_CARDEMU \ 44 {0x0c00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 45 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x04 \ 46 /* 0xc00[7:0] = 4 turn off 3-wire */}, \ 47 {0x0e00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 48 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x04 \ 49 /* 0xe00[7:0] = 4 turn off 3-wire */}, \ 50 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 51 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0 \ 52 /* 0x2[0] = 0 RESET BB, CLOSE RF */}, \ 53 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 54 PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US \ 55 /*Delay 1us*/}, \ 56 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 57 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 58 /* Whole BB is reset*/}, \ 59 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 60 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x2A \ 61 /* 0x07[7:0] = 0x28 sps pwm mode 0x2a for BT coex*/}, \ 62 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 63 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x02, 0 \ 64 /*0x8[1] = 0 ANA clk =500k */}, \ 65 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 66 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1 \ 67 /*0x04[9] = 1 turn off MAC by HW state machine*/}, \ 68 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 69 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0 \ 70 /*wait till 0x04[9] = 0 polling until return 0 to disable*/}, 71 72 #define RTL8812_TRANS_CARDEMU_TO_SUS \ 73 {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 74 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xF0, 0xc0}, \ 75 {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 76 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xF0, 0xE0}, \ 77 {0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 78 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x07 \ 79 /* gpio11 input mode, gpio10~8 output mode */}, \ 80 {0x0045, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 81 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00 \ 82 /* gpio 0~7 output same value as input ?? */}, \ 83 {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 84 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xff \ 85 /* gpio0~7 output mode */}, \ 86 {0x0047, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 87 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 88 /* 0x47[7:0] = 00 gpio mode */}, \ 89 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 90 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 91 /* suspend option all off */}, \ 92 {0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 93 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x80, BIT7 \ 94 /*0x14[7] = 1 turn on ZCD */}, \ 95 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 96 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, BIT0 \ 97 /* 0x15[0] =1 trun on ZCD */}, \ 98 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 99 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x10, BIT4 \ 100 /*0x23[4] = 1 hpon LDO sleep mode */}, \ 101 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 102 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x02, 0 \ 103 /*0x8[1] = 0 ANA clk =500k */}, \ 104 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 105 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, BIT3 \ 106 /*0x04[11] = 2b'11 enable WL suspend for PCIe*/}, 107 108 #define RTL8812_TRANS_SUS_TO_CARDEMU \ 109 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 110 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, 0 \ 111 /*0x04[11] = 2b'01enable WL suspend*/}, \ 112 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 113 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x10, 0 \ 114 /*0x23[4] = 0 hpon LDO sleep mode leave */}, \ 115 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 116 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, 0 \ 117 /* 0x15[0] =0 trun off ZCD */}, \ 118 {0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 119 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x80, 0 \ 120 /*0x14[7] = 0 turn off ZCD */}, \ 121 {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 122 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00 \ 123 /* gpio0~7 input mode */}, \ 124 {0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 125 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00 \ 126 /* gpio11 input mode, gpio10~8 input mode */}, 127 128 #define RTL8812_TRANS_CARDEMU_TO_CARDDIS \ 129 {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 130 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0 \ 131 /*0x03[2] = 0, reset 8051*/}, \ 132 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 133 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x05 \ 134 /*0x80=05h if reload fw, fill the default value of host_CPU handshake field*/}, \ 135 {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 136 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xF0, 0xcc}, \ 137 {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 138 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xF0, 0xEC}, \ 139 {0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 140 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x07 \ 141 /* gpio11 input mode, gpio10~8 output mode */}, \ 142 {0x0045, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 143 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00 \ 144 /* gpio 0~7 output same value as input ?? */}, \ 145 {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 146 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xff \ 147 /* gpio0~7 output mode */}, \ 148 {0x0047, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 149 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 150 /* 0x47[7:0] = 00 gpio mode */}, \ 151 {0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 152 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x80, BIT7 \ 153 /*0x14[7] = 1 turn on ZCD */}, \ 154 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 155 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, BIT0 \ 156 /* 0x15[0] =1 trun on ZCD */}, \ 157 {0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 158 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, 0 \ 159 /*0x12[0] = 0 force PFM mode */}, \ 160 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 161 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x10, BIT4 \ 162 /*0x23[4] = 1 hpon LDO sleep mode */}, \ 163 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 164 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x02, 0 \ 165 /*0x8[1] = 0 ANA clk =500k */}, \ 166 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 167 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20 \ 168 /*0x07=0x20 , SOP option to disable BG/MB*/}, \ 169 {0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 170 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 171 /*0x01f[1]=0 , disable RFC_0 control REG_RF_CTRL_8812 */}, \ 172 {0x0076, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 173 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 174 /*0x076[1]=0 , disable RFC_1 control REG_OPT_CTRL_8812 +2 */}, \ 175 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 176 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, BIT3 \ 177 /*0x04[11] = 2b'01 enable WL suspend*/}, 178 179 #define RTL8812_TRANS_CARDDIS_TO_CARDEMU \ 180 {0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 181 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0 \ 182 /*0x12[0] = 1 force PWM mode */}, \ 183 {0x0014, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 184 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x80, 0 \ 185 /*0x14[7] = 0 turn off ZCD */}, \ 186 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 187 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x01, 0 \ 188 /* 0x15[0] =0 trun off ZCD */}, \ 189 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 190 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x10, 0 \ 191 /*0x23[4] = 0 hpon LDO leave sleep mode */}, \ 192 {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 193 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00 \ 194 /* gpio0~7 input mode */}, \ 195 {0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 196 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00 \ 197 /* gpio11 input mode, gpio10~8 input mode */}, \ 198 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 199 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0 \ 200 /*0x04[10] = 0, enable SW LPS PCIE only*/}, \ 201 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 202 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, 0 \ 203 /*0x04[11] = 2b'01enable WL suspend*/}, \ 204 {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 205 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2 \ 206 /*0x03[2] = 1, enable 8051*/}, \ 207 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 208 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 209 /*PCIe DMA start*/}, 210 211 #define RTL8812_TRANS_CARDEMU_TO_PDN \ 212 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 213 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7 \ 214 /* 0x04[15] = 1*/}, 215 216 #define RTL8812_TRANS_PDN_TO_CARDEMU \ 217 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 218 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0 \ 219 /* 0x04[15] = 0*/}, 220 221 #define RTL8812_TRANS_ACT_TO_LPS \ 222 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 223 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF \ 224 /*PCIe DMA stop*/}, \ 225 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 226 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F \ 227 /*Tx Pause*/}, \ 228 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 229 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 230 /*Should be zero if no packet is transmitting*/}, \ 231 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 232 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 233 /*Should be zero if no packet is transmitting*/}, \ 234 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 235 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 236 /*Should be zero if no packet is transmitting*/}, \ 237 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 238 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 239 /*Should be zero if no packet is transmitting*/}, \ 240 {0x0c00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 241 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x04 \ 242 /* 0xc00[7:0] = 4 turn off 3-wire */}, \ 243 {0x0e00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 244 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x04 \ 245 /* 0xe00[7:0] = 4 turn off 3-wire */}, \ 246 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 247 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0 \ 248 /*CCK and OFDM are disabled,and clock are gated,and RF closed*/}, \ 249 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 250 PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US \ 251 /*Delay 1us*/}, \ 252 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 253 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 254 /* Whole BB is reset*/}, \ 255 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 256 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03 \ 257 /*Reset MAC TRX*/}, \ 258 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 259 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 260 /*check if removed later*/}, \ 261 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 262 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5 \ 263 /*Respond TxOK to scheduler*/}, 264 265 #define RTL8812_TRANS_LPS_TO_ACT \ 266 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 267 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84 \ 268 /*SDIO RPWM*/}, \ 269 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 270 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \ 271 /*USB RPWM*/}, \ 272 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 273 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \ 274 /*PCIe RPWM*/}, \ 275 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 276 PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS \ 277 /*Delay*/}, \ 278 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 279 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0 \ 280 /*. 0x08[4] = 0 switch TSF to 40M*/}, \ 281 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 282 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0 \ 283 /*Polling 0x109[7]=0 TSF in 40M*/}, \ 284 {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 285 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6|BIT7, 0 \ 286 /*. 0x29[7:6] = 2b'00 enable BB clock*/}, \ 287 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 288 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1 \ 289 /*. 0x101[1] = 1*/}, \ 290 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 291 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF \ 292 /*. 0x100[7:0] = 0xFF enable WMAC TRX*/}, \ 293 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 294 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0 \ 295 /*. 0x02[1:0] = 2b'11 enable BB macro*/}, \ 296 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 297 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 298 /*. 0x522 = 0*/}, 299 300 #define RTL8812_TRANS_END \ 301 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 302 0, PWR_CMD_END, 0, 0}, 303 304 extern struct wlan_pwr_cfg rtl8812_power_on_flow 305 [RTL8812_TRANS_CARDEMU_TO_ACT_STEPS + 306 RTL8812_TRANS_END_STEPS]; 307 extern struct wlan_pwr_cfg rtl8812_radio_off_flow 308 [RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + 309 RTL8812_TRANS_END_STEPS]; 310 extern struct wlan_pwr_cfg rtl8812_card_disable_flow 311 [RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + 312 RTL8812_TRANS_CARDEMU_TO_PDN_STEPS + 313 RTL8812_TRANS_END_STEPS]; 314 extern struct wlan_pwr_cfg rtl8812_card_enable_flow 315 [RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + 316 RTL8812_TRANS_CARDEMU_TO_PDN_STEPS + 317 RTL8812_TRANS_END_STEPS]; 318 extern struct wlan_pwr_cfg rtl8812_suspend_flow 319 [RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + 320 RTL8812_TRANS_CARDEMU_TO_SUS_STEPS + 321 RTL8812_TRANS_END_STEPS]; 322 extern struct wlan_pwr_cfg rtl8812_resume_flow 323 [RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + 324 RTL8812_TRANS_CARDEMU_TO_SUS_STEPS + 325 RTL8812_TRANS_END_STEPS]; 326 extern struct wlan_pwr_cfg rtl8812_hwpdn_flow 327 [RTL8812_TRANS_ACT_TO_CARDEMU_STEPS + 328 RTL8812_TRANS_CARDEMU_TO_PDN_STEPS + 329 RTL8812_TRANS_END_STEPS]; 330 extern struct wlan_pwr_cfg rtl8812_enter_lps_flow 331 [RTL8812_TRANS_ACT_TO_LPS_STEPS + 332 RTL8812_TRANS_END_STEPS]; 333 extern struct wlan_pwr_cfg rtl8812_leave_lps_flow 334 [RTL8812_TRANS_LPS_TO_ACT_STEPS + 335 RTL8812_TRANS_END_STEPS]; 336 337 /* Check document WM-20130516-JackieLau-RTL8821A_Power_Architecture-R10.vsd 338 * There are 6 HW Power States: 339 * 0: POFF--Power Off 340 * 1: PDN--Power Down 341 * 2: CARDEMU--Card Emulation 342 * 3: ACT--Active Mode 343 * 4: LPS--Low Power State 344 * 5: SUS--Suspend 345 * 346 * The transision from different states are defined below 347 * TRANS_CARDEMU_TO_ACT 348 * TRANS_ACT_TO_CARDEMU 349 * TRANS_CARDEMU_TO_SUS 350 * TRANS_SUS_TO_CARDEMU 351 * TRANS_CARDEMU_TO_PDN 352 * TRANS_ACT_TO_LPS 353 * TRANS_LPS_TO_ACT 354 * 355 * TRANS_END 356 */ 357 #define RTL8821A_TRANS_CARDEMU_TO_ACT_STEPS 25 358 #define RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS 15 359 #define RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS 15 360 #define RTL8821A_TRANS_SUS_TO_CARDEMU_STEPS 15 361 #define RTL8821A_TRANS_CARDDIS_TO_CARDEMU_STEPS 15 362 #define RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS 15 363 #define RTL8821A_TRANS_PDN_TO_CARDEMU_STEPS 15 364 #define RTL8821A_TRANS_ACT_TO_LPS_STEPS 15 365 #define RTL8821A_TRANS_LPS_TO_ACT_STEPS 15 366 #define RTL8821A_TRANS_END_STEPS 1 367 368 #define RTL8821A_TRANS_CARDEMU_TO_ACT \ 369 {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 370 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,\ 371 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0 \ 372 /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/}, \ 373 {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 374 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,\ 375 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0 \ 376 /*0x67[0] = 0 to disable BT_GPS_SEL pins*/}, \ 377 {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 378 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,\ 379 PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS \ 380 /*Delay 1ms*/}, \ 381 {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 382 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,\ 383 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, 0 \ 384 /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/}, \ 385 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 386 PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT4|BIT3|BIT2), 0 \ 387 /* disable SW LPS 0x04[10]=0 and WLSUS_EN 0x04[12:11]=0*/}, \ 388 {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 389 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 , BIT0 \ 390 /* Disable USB suspend */}, \ 391 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 392 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1 \ 393 /* wait till 0x04[17] = 1 power ready*/}, \ 394 {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 395 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 , 0 \ 396 /* Enable USB suspend */}, \ 397 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 398 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0 \ 399 /* release WLON reset 0x04[16]=1*/}, \ 400 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 401 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0 \ 402 /* disable HWPDN 0x04[15]=0*/}, \ 403 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 404 PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT4|BIT3), 0 \ 405 /* disable WL suspend*/}, \ 406 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 407 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0 \ 408 /* polling until return 0*/}, \ 409 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 410 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0 \ 411 /**/}, \ 412 {0x004F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 413 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0 \ 414 /*0x4C[24] = 0x4F[0] = 1, switch DPDT_SEL_P output from WL BB */},\ 415 {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 416 PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT5|BIT4), (BIT5|BIT4) \ 417 /*0x66[13] = 0x67[5] = 1, switch for PAPE_G/PAPE_A \ 418 from WL BB ; 0x66[12] = 0x67[4] = 1, switch LNAON from WL BB */},\ 419 {0x0025, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 420 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6, 0 \ 421 /*anapar_mac<118> , 0x25[6]=0 by wlan single function*/},\ 422 {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 423 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1 \ 424 /*Enable falling edge triggering interrupt*/},\ 425 {0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 426 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1 \ 427 /*Enable GPIO9 interrupt mode*/},\ 428 {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 429 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 430 /*Enable GPIO9 input mode*/},\ 431 {0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 432 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0 \ 433 /*Enable HSISR GPIO[C:0] interrupt*/},\ 434 {0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 435 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1 \ 436 /*Enable HSISR GPIO9 interrupt*/},\ 437 {0x007A, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 438 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3A \ 439 /*0x7A = 0x3A start BT*/},\ 440 {0x002E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 441 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF , 0x82 \ 442 /* 0x2C[23:12]=0x820 ; XTAL trim */}, \ 443 {0x0010, PWR_CUT_A_MSK , PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 444 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6 , BIT6 \ 445 /* 0x10[6]=1 */}, 446 447 #define RTL8821A_TRANS_ACT_TO_CARDEMU \ 448 {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 449 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 450 /*0x1F[7:0] = 0 turn off RF*/}, \ 451 {0x004F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 452 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0 \ 453 /*0x4C[24] = 0x4F[0] = 0, switch DPDT_SEL_P output from \ 454 register 0x65[2] */},\ 455 {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 456 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 457 /*Enable rising edge triggering interrupt*/}, \ 458 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 459 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1 \ 460 /*0x04[9] = 1 turn off MAC by HW state machine*/}, \ 461 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 462 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0 \ 463 /*wait till 0x04[9] = 0 polling until return 0 to disable*/}, \ 464 {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 465 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,\ 466 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5 \ 467 /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/}, \ 468 {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 469 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,\ 470 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0 \ 471 /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/}, 472 473 #define RTL8821A_TRANS_CARDEMU_TO_SUS \ 474 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 475 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3) \ 476 /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/}, \ 477 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 478 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,\ 479 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3 \ 480 /*0x04[12:11] = 2b'01 enable WL suspend*/}, \ 481 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 482 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4 \ 483 /*0x23[4] = 1b'1 12H LDO enter sleep mode*/}, \ 484 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 485 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20 \ 486 /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/}, \ 487 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 488 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4 \ 489 /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/}, \ 490 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 491 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0 \ 492 /*Set SDIO suspend local register*/}, \ 493 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 494 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0 \ 495 /*wait power state to suspend*/}, 496 497 #define RTL8821A_TRANS_SUS_TO_CARDEMU \ 498 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 499 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT7, 0 \ 500 /*clear suspend enable and power down enable*/}, \ 501 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 502 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0 \ 503 /*Set SDIO suspend local register*/}, \ 504 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 505 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1 \ 506 /*wait power state to suspend*/},\ 507 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 508 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0 \ 509 /*0x23[4] = 1b'0 12H LDO enter normal mode*/}, \ 510 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 511 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, 0 \ 512 /*0x04[12:11] = 2b'00 disable WL suspend*/}, 513 514 #define RTL8821A_TRANS_CARDEMU_TO_CARDDIS \ 515 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 516 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20 \ 517 /*0x07=0x20 , SOP option to disable BG/MB*/}, \ 518 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 519 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,\ 520 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3 \ 521 /*0x04[12:11] = 2b'01 enable WL suspend*/}, \ 522 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 523 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2 \ 524 /*0x04[10] = 1, enable SW LPS*/}, \ 525 {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 526 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1 \ 527 /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/}, \ 528 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 529 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4 \ 530 /*0x23[4] = 1b'1 12H LDO enter sleep mode*/}, \ 531 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 532 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0 \ 533 /*Set SDIO suspend local register*/}, \ 534 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 535 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0 \ 536 /*wait power state to suspend*/}, 537 538 #define RTL8821A_TRANS_CARDDIS_TO_CARDEMU \ 539 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 540 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT7, 0 \ 541 /*clear suspend enable and power down enable*/}, \ 542 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 543 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0 \ 544 /*Set SDIO suspend local register*/}, \ 545 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 546 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1 \ 547 /*wait power state to suspend*/},\ 548 {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 549 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0 \ 550 /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/}, \ 551 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 552 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, 0 \ 553 /*0x04[12:11] = 2b'00 disable WL suspend*/},\ 554 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 555 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0 \ 556 /*0x23[4] = 1b'0 12H LDO enter normal mode*/}, \ 557 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 558 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 559 /*PCIe DMA start*/}, 560 561 #define RTL8821A_TRANS_CARDEMU_TO_PDN \ 562 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 563 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4 \ 564 /*0x23[4] = 1b'1 12H LDO enter sleep mode*/}, \ 565 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 566 PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK,\ 567 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20 \ 568 /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/}, \ 569 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 570 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0 \ 571 /* 0x04[16] = 0*/},\ 572 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 573 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7 \ 574 /* 0x04[15] = 1*/}, 575 576 #define RTL8821A_TRANS_PDN_TO_CARDEMU \ 577 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 578 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0 \ 579 /* 0x04[15] = 0*/}, 580 581 #define RTL8821A_TRANS_ACT_TO_LPS \ 582 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 583 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF \ 584 /*PCIe DMA stop*/}, \ 585 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 586 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF \ 587 /*Tx Pause*/}, \ 588 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 589 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 590 /*Should be zero if no packet is transmitting*/}, \ 591 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 592 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 593 /*Should be zero if no packet is transmitting*/}, \ 594 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 595 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 596 /*Should be zero if no packet is transmitting*/}, \ 597 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 598 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 599 /*Should be zero if no packet is transmitting*/}, \ 600 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 601 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0 \ 602 /*CCK and OFDM are disabled,and clock are gated*/}, \ 603 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 604 PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US \ 605 /*Delay 1us*/}, \ 606 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 607 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 608 /*Whole BB is reset*/}, \ 609 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 610 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03 \ 611 /*Reset MAC TRX*/}, \ 612 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 613 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0 \ 614 /*check if removed later*/}, \ 615 {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 616 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00 \ 617 /*When driver enter Sus/ Disable, enable LOP for BT*/}, \ 618 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 619 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5 \ 620 /*Respond TxOK to scheduler*/}, 621 622 #define RTL8821A_TRANS_LPS_TO_ACT \ 623 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 624 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84 \ 625 /*SDIO RPWM*/},\ 626 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,\ 627 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \ 628 /*USB RPWM*/},\ 629 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 630 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \ 631 /*PCIe RPWM*/},\ 632 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 633 PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS \ 634 /*Delay*/},\ 635 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 636 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0 \ 637 /*. 0x08[4] = 0 switch TSF to 40M*/},\ 638 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 639 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0 \ 640 /*Polling 0x109[7]=0 TSF in 40M*/},\ 641 {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 642 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6|BIT7, 0 \ 643 /*. 0x29[7:6] = 2b'00 enable BB clock*/},\ 644 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 645 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1 \ 646 /*. 0x101[1] = 1*/},\ 647 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 648 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF \ 649 /*. 0x100[7:0] = 0xFF enable WMAC TRX*/},\ 650 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 651 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0 \ 652 /*. 0x02[1:0] = 2b'11 enable BB macro*/},\ 653 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 654 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 655 /*. 0x522 = 0*/}, 656 657 #define RTL8821A_TRANS_END \ 658 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 659 0, PWR_CMD_END, 0, 0}, 660 661 extern struct wlan_pwr_cfg rtl8821A_power_on_flow 662 [RTL8821A_TRANS_CARDEMU_TO_ACT_STEPS + 663 RTL8821A_TRANS_END_STEPS]; 664 extern struct wlan_pwr_cfg rtl8821A_radio_off_flow 665 [RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + 666 RTL8821A_TRANS_END_STEPS]; 667 extern struct wlan_pwr_cfg rtl8821A_card_disable_flow 668 [RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + 669 RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS + 670 RTL8821A_TRANS_END_STEPS]; 671 extern struct wlan_pwr_cfg rtl8821A_card_enable_flow 672 [RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + 673 RTL8821A_TRANS_CARDEMU_TO_ACT_STEPS + 674 RTL8821A_TRANS_END_STEPS]; 675 extern struct wlan_pwr_cfg rtl8821A_suspend_flow 676 [RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + 677 RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS + 678 RTL8821A_TRANS_END_STEPS]; 679 extern struct wlan_pwr_cfg rtl8821A_resume_flow 680 [RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + 681 RTL8821A_TRANS_CARDEMU_TO_SUS_STEPS + 682 RTL8821A_TRANS_END_STEPS]; 683 extern struct wlan_pwr_cfg rtl8821A_hwpdn_flow 684 [RTL8821A_TRANS_ACT_TO_CARDEMU_STEPS + 685 RTL8821A_TRANS_CARDEMU_TO_PDN_STEPS + 686 RTL8821A_TRANS_END_STEPS]; 687 extern struct wlan_pwr_cfg rtl8821A_enter_lps_flow 688 [RTL8821A_TRANS_ACT_TO_LPS_STEPS + 689 RTL8821A_TRANS_END_STEPS]; 690 extern struct wlan_pwr_cfg rtl8821A_leave_lps_flow 691 [RTL8821A_TRANS_LPS_TO_ACT_STEPS + 692 RTL8821A_TRANS_END_STEPS]; 693 694 /*RTL8812 Power Configuration CMDs for PCIe interface*/ 695 #define RTL8812_NIC_PWR_ON_FLOW rtl8812_power_on_flow 696 #define RTL8812_NIC_RF_OFF_FLOW rtl8812_radio_off_flow 697 #define RTL8812_NIC_DISABLE_FLOW rtl8812_card_disable_flow 698 #define RTL8812_NIC_ENABLE_FLOW rtl8812_card_enable_flow 699 #define RTL8812_NIC_SUSPEND_FLOW rtl8812_suspend_flow 700 #define RTL8812_NIC_RESUME_FLOW rtl8812_resume_flow 701 #define RTL8812_NIC_PDN_FLOW rtl8812_hwpdn_flow 702 #define RTL8812_NIC_LPS_ENTER_FLOW rtl8812_enter_lps_flow 703 #define RTL8812_NIC_LPS_LEAVE_FLOW rtl8812_leave_lps_flow 704 705 /* RTL8821 Power Configuration CMDs for PCIe interface */ 706 #define RTL8821A_NIC_PWR_ON_FLOW rtl8821A_power_on_flow 707 #define RTL8821A_NIC_RF_OFF_FLOW rtl8821A_radio_off_flow 708 #define RTL8821A_NIC_DISABLE_FLOW rtl8821A_card_disable_flow 709 #define RTL8821A_NIC_ENABLE_FLOW rtl8821A_card_enable_flow 710 #define RTL8821A_NIC_SUSPEND_FLOW rtl8821A_suspend_flow 711 #define RTL8821A_NIC_RESUME_FLOW rtl8821A_resume_flow 712 #define RTL8821A_NIC_PDN_FLOW rtl8821A_hwpdn_flow 713 #define RTL8821A_NIC_LPS_ENTER_FLOW rtl8821A_enter_lps_flow 714 #define RTL8821A_NIC_LPS_LEAVE_FLOW rtl8821A_leave_lps_flow 715 716 #endif 717