1 /*
2 * Product specific probe and attach routines for:
3 * aic7901 and aic7902 SCSI controllers
4 *
5 * Copyright (c) 1994-2001 Justin T. Gibbs.
6 * Copyright (c) 2000-2002 Adaptec Inc.
7 * All rights reserved.
8 *
9 * Redistribution and use in source and binary forms, with or without
10 * modification, are permitted provided that the following conditions
11 * are met:
12 * 1. Redistributions of source code must retain the above copyright
13 * notice, this list of conditions, and the following disclaimer,
14 * without modification.
15 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
16 * substantially similar to the "NO WARRANTY" disclaimer below
17 * ("Disclaimer") and any redistribution must be conditioned upon
18 * including a substantially similar Disclaimer requirement for further
19 * binary redistribution.
20 * 3. Neither the names of the above-listed copyright holders nor the names
21 * of any contributors may be used to endorse or promote products derived
22 * from this software without specific prior written permission.
23 *
24 * Alternatively, this software may be distributed under the terms of the
25 * GNU General Public License ("GPL") version 2 as published by the Free
26 * Software Foundation.
27 *
28 * NO WARRANTY
29 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
30 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
31 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
32 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
33 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
34 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
35 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
36 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
37 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
38 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
39 * POSSIBILITY OF SUCH DAMAGES.
40 *
41 * $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#92 $
42 */
43
44 #include "aic79xx_osm.h"
45 #include "aic79xx_inline.h"
46 #include "aic79xx_pci.h"
47
48 static inline uint64_t
ahd_compose_id(u_int device,u_int vendor,u_int subdevice,u_int subvendor)49 ahd_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor)
50 {
51 uint64_t id;
52
53 id = subvendor
54 | (subdevice << 16)
55 | ((uint64_t)vendor << 32)
56 | ((uint64_t)device << 48);
57
58 return (id);
59 }
60
61 #define ID_AIC7902_PCI_REV_A4 0x3
62 #define ID_AIC7902_PCI_REV_B0 0x10
63 #define SUBID_HP 0x0E11
64
65 #define DEVID_9005_HOSTRAID(id) ((id) & 0x80)
66
67 #define DEVID_9005_TYPE(id) ((id) & 0xF)
68 #define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */
69 #define DEVID_9005_TYPE_HBA_2EXT 0x1 /* 2 External Ports */
70 #define DEVID_9005_TYPE_IROC 0x8 /* Raid(0,1,10) Card */
71 #define DEVID_9005_TYPE_MB 0xF /* On Motherboard */
72
73 #define DEVID_9005_MFUNC(id) ((id) & 0x10)
74
75 #define DEVID_9005_PACKETIZED(id) ((id) & 0x8000)
76
77 #define SUBID_9005_TYPE(id) ((id) & 0xF)
78 #define SUBID_9005_TYPE_HBA 0x0 /* Standard Card */
79 #define SUBID_9005_TYPE_MB 0xF /* On Motherboard */
80
81 #define SUBID_9005_AUTOTERM(id) (((id) & 0x10) == 0)
82
83 #define SUBID_9005_LEGACYCONN_FUNC(id) ((id) & 0x20)
84
85 #define SUBID_9005_SEEPTYPE(id) (((id) & 0x0C0) >> 6)
86 #define SUBID_9005_SEEPTYPE_NONE 0x0
87 #define SUBID_9005_SEEPTYPE_4K 0x1
88
89 static ahd_device_setup_t ahd_aic7901_setup;
90 static ahd_device_setup_t ahd_aic7901A_setup;
91 static ahd_device_setup_t ahd_aic7902_setup;
92 static ahd_device_setup_t ahd_aic790X_setup;
93
94 static const struct ahd_pci_identity ahd_pci_ident_table[] =
95 {
96 /* aic7901 based controllers */
97 {
98 ID_AHA_29320A,
99 ID_ALL_MASK,
100 "Adaptec 29320A Ultra320 SCSI adapter",
101 ahd_aic7901_setup
102 },
103 {
104 ID_AHA_29320ALP,
105 ID_ALL_MASK,
106 "Adaptec 29320ALP PCIx Ultra320 SCSI adapter",
107 ahd_aic7901_setup
108 },
109 {
110 ID_AHA_29320LPE,
111 ID_ALL_MASK,
112 "Adaptec 29320LPE PCIe Ultra320 SCSI adapter",
113 ahd_aic7901_setup
114 },
115 /* aic7901A based controllers */
116 {
117 ID_AHA_29320LP,
118 ID_ALL_MASK,
119 "Adaptec 29320LP Ultra320 SCSI adapter",
120 ahd_aic7901A_setup
121 },
122 /* aic7902 based controllers */
123 {
124 ID_AHA_29320,
125 ID_ALL_MASK,
126 "Adaptec 29320 Ultra320 SCSI adapter",
127 ahd_aic7902_setup
128 },
129 {
130 ID_AHA_29320B,
131 ID_ALL_MASK,
132 "Adaptec 29320B Ultra320 SCSI adapter",
133 ahd_aic7902_setup
134 },
135 {
136 ID_AHA_39320,
137 ID_ALL_MASK,
138 "Adaptec 39320 Ultra320 SCSI adapter",
139 ahd_aic7902_setup
140 },
141 {
142 ID_AHA_39320_B,
143 ID_ALL_MASK,
144 "Adaptec 39320 Ultra320 SCSI adapter",
145 ahd_aic7902_setup
146 },
147 {
148 ID_AHA_39320_B_DELL,
149 ID_ALL_MASK,
150 "Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter",
151 ahd_aic7902_setup
152 },
153 {
154 ID_AHA_39320A,
155 ID_ALL_MASK,
156 "Adaptec 39320A Ultra320 SCSI adapter",
157 ahd_aic7902_setup
158 },
159 {
160 ID_AHA_39320D,
161 ID_ALL_MASK,
162 "Adaptec 39320D Ultra320 SCSI adapter",
163 ahd_aic7902_setup
164 },
165 {
166 ID_AHA_39320D_HP,
167 ID_ALL_MASK,
168 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter",
169 ahd_aic7902_setup
170 },
171 {
172 ID_AHA_39320D_B,
173 ID_ALL_MASK,
174 "Adaptec 39320D Ultra320 SCSI adapter",
175 ahd_aic7902_setup
176 },
177 {
178 ID_AHA_39320D_B_HP,
179 ID_ALL_MASK,
180 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter",
181 ahd_aic7902_setup
182 },
183 /* Generic chip probes for devices we don't know 'exactly' */
184 {
185 ID_AIC7901 & ID_9005_GENERIC_MASK,
186 ID_9005_GENERIC_MASK,
187 "Adaptec AIC7901 Ultra320 SCSI adapter",
188 ahd_aic7901_setup
189 },
190 {
191 ID_AIC7901A & ID_DEV_VENDOR_MASK,
192 ID_DEV_VENDOR_MASK,
193 "Adaptec AIC7901A Ultra320 SCSI adapter",
194 ahd_aic7901A_setup
195 },
196 {
197 ID_AIC7902 & ID_9005_GENERIC_MASK,
198 ID_9005_GENERIC_MASK,
199 "Adaptec AIC7902 Ultra320 SCSI adapter",
200 ahd_aic7902_setup
201 }
202 };
203
204 static const u_int ahd_num_pci_devs = ARRAY_SIZE(ahd_pci_ident_table);
205
206 #define DEVCONFIG 0x40
207 #define PCIXINITPAT 0x0000E000ul
208 #define PCIXINIT_PCI33_66 0x0000E000ul
209 #define PCIXINIT_PCIX50_66 0x0000C000ul
210 #define PCIXINIT_PCIX66_100 0x0000A000ul
211 #define PCIXINIT_PCIX100_133 0x00008000ul
212 #define PCI_BUS_MODES_INDEX(devconfig) \
213 (((devconfig) & PCIXINITPAT) >> 13)
214 static const char *pci_bus_modes[] =
215 {
216 "PCI bus mode unknown",
217 "PCI bus mode unknown",
218 "PCI bus mode unknown",
219 "PCI bus mode unknown",
220 "PCI-X 101-133MHz",
221 "PCI-X 67-100MHz",
222 "PCI-X 50-66MHz",
223 "PCI 33 or 66MHz"
224 };
225
226 #define TESTMODE 0x00000800ul
227 #define IRDY_RST 0x00000200ul
228 #define FRAME_RST 0x00000100ul
229 #define PCI64BIT 0x00000080ul
230 #define MRDCEN 0x00000040ul
231 #define ENDIANSEL 0x00000020ul
232 #define MIXQWENDIANEN 0x00000008ul
233 #define DACEN 0x00000004ul
234 #define STPWLEVEL 0x00000002ul
235 #define QWENDIANSEL 0x00000001ul
236
237 #define DEVCONFIG1 0x44
238 #define PREQDIS 0x01
239
240 #define CSIZE_LATTIME 0x0c
241 #define CACHESIZE 0x000000fful
242 #define LATTIME 0x0000ff00ul
243
244 static int ahd_check_extport(struct ahd_softc *ahd);
245 static void ahd_configure_termination(struct ahd_softc *ahd,
246 u_int adapter_control);
247 static void ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat);
248 static void ahd_pci_intr(struct ahd_softc *ahd);
249
250 const struct ahd_pci_identity *
ahd_find_pci_device(ahd_dev_softc_t pci)251 ahd_find_pci_device(ahd_dev_softc_t pci)
252 {
253 uint64_t full_id;
254 uint16_t device;
255 uint16_t vendor;
256 uint16_t subdevice;
257 uint16_t subvendor;
258 const struct ahd_pci_identity *entry;
259 u_int i;
260
261 vendor = ahd_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2);
262 device = ahd_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2);
263 subvendor = ahd_pci_read_config(pci, PCI_SUBSYSTEM_VENDOR_ID, /*bytes*/2);
264 subdevice = ahd_pci_read_config(pci, PCI_SUBSYSTEM_ID, /*bytes*/2);
265 full_id = ahd_compose_id(device,
266 vendor,
267 subdevice,
268 subvendor);
269
270 /*
271 * Controllers, mask out the IROC/HostRAID bit
272 */
273
274 full_id &= ID_ALL_IROC_MASK;
275
276 for (i = 0; i < ahd_num_pci_devs; i++) {
277 entry = &ahd_pci_ident_table[i];
278 if (entry->full_id == (full_id & entry->id_mask)) {
279 /* Honor exclusion entries. */
280 if (entry->name == NULL)
281 return (NULL);
282 return (entry);
283 }
284 }
285 return (NULL);
286 }
287
288 int
ahd_pci_config(struct ahd_softc * ahd,const struct ahd_pci_identity * entry)289 ahd_pci_config(struct ahd_softc *ahd, const struct ahd_pci_identity *entry)
290 {
291 u_int command;
292 uint32_t devconfig;
293 uint16_t subvendor;
294 int error;
295
296 ahd->description = entry->name;
297 /*
298 * Record if this is an HP board.
299 */
300 subvendor = ahd_pci_read_config(ahd->dev_softc,
301 PCI_SUBSYSTEM_VENDOR_ID, /*bytes*/2);
302 if (subvendor == SUBID_HP)
303 ahd->flags |= AHD_HP_BOARD;
304
305 error = entry->setup(ahd);
306 if (error != 0)
307 return (error);
308
309 devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4);
310 if ((devconfig & PCIXINITPAT) == PCIXINIT_PCI33_66) {
311 ahd->chip |= AHD_PCI;
312 /* Disable PCIX workarounds when running in PCI mode. */
313 ahd->bugs &= ~AHD_PCIX_BUG_MASK;
314 } else {
315 ahd->chip |= AHD_PCIX;
316 }
317 ahd->bus_description = pci_bus_modes[PCI_BUS_MODES_INDEX(devconfig)];
318
319 ahd_power_state_change(ahd, AHD_POWER_STATE_D0);
320
321 error = ahd_pci_map_registers(ahd);
322 if (error != 0)
323 return (error);
324
325 /*
326 * If we need to support high memory, enable dual
327 * address cycles. This bit must be set to enable
328 * high address bit generation even if we are on a
329 * 64bit bus (PCI64BIT set in devconfig).
330 */
331 if ((ahd->flags & (AHD_39BIT_ADDRESSING|AHD_64BIT_ADDRESSING)) != 0) {
332 if (bootverbose)
333 printk("%s: Enabling 39Bit Addressing\n",
334 ahd_name(ahd));
335 devconfig = ahd_pci_read_config(ahd->dev_softc,
336 DEVCONFIG, /*bytes*/4);
337 devconfig |= DACEN;
338 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG,
339 devconfig, /*bytes*/4);
340 }
341
342 /* Ensure busmastering is enabled */
343 command = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2);
344 command |= PCIM_CMD_BUSMASTEREN;
345 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, command, /*bytes*/2);
346
347 error = ahd_softc_init(ahd);
348 if (error != 0)
349 return (error);
350
351 ahd->bus_intr = ahd_pci_intr;
352
353 error = ahd_reset(ahd, /*reinit*/FALSE);
354 if (error != 0)
355 return (ENXIO);
356
357 ahd->pci_cachesize =
358 ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME,
359 /*bytes*/1) & CACHESIZE;
360 ahd->pci_cachesize *= 4;
361
362 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
363 /* See if we have a SEEPROM and perform auto-term */
364 error = ahd_check_extport(ahd);
365 if (error != 0)
366 return (error);
367
368 /* Core initialization */
369 error = ahd_init(ahd);
370 if (error != 0)
371 return (error);
372 ahd->init_level++;
373
374 /*
375 * Allow interrupts now that we are completely setup.
376 */
377 return ahd_pci_map_int(ahd);
378 }
379
380 void __maybe_unused
ahd_pci_suspend(struct ahd_softc * ahd)381 ahd_pci_suspend(struct ahd_softc *ahd)
382 {
383 /*
384 * Save chip register configuration data for chip resets
385 * that occur during runtime and resume events.
386 */
387 ahd->suspend_state.pci_state.devconfig =
388 ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4);
389 ahd->suspend_state.pci_state.command =
390 ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/1);
391 ahd->suspend_state.pci_state.csize_lattime =
392 ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, /*bytes*/1);
393
394 }
395
396 void __maybe_unused
ahd_pci_resume(struct ahd_softc * ahd)397 ahd_pci_resume(struct ahd_softc *ahd)
398 {
399 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG,
400 ahd->suspend_state.pci_state.devconfig, /*bytes*/4);
401 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND,
402 ahd->suspend_state.pci_state.command, /*bytes*/1);
403 ahd_pci_write_config(ahd->dev_softc, CSIZE_LATTIME,
404 ahd->suspend_state.pci_state.csize_lattime, /*bytes*/1);
405 }
406
407 /*
408 * Perform some simple tests that should catch situations where
409 * our registers are invalidly mapped.
410 */
411 int
ahd_pci_test_register_access(struct ahd_softc * ahd)412 ahd_pci_test_register_access(struct ahd_softc *ahd)
413 {
414 uint32_t cmd;
415 u_int targpcistat;
416 u_int pci_status1;
417 int error;
418 uint8_t hcntrl;
419
420 error = EIO;
421
422 /*
423 * Enable PCI error interrupt status, but suppress NMIs
424 * generated by SERR raised due to target aborts.
425 */
426 cmd = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2);
427 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND,
428 cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2);
429
430 /*
431 * First a simple test to see if any
432 * registers can be read. Reading
433 * HCNTRL has no side effects and has
434 * at least one bit that is guaranteed to
435 * be zero so it is a good register to
436 * use for this test.
437 */
438 hcntrl = ahd_inb(ahd, HCNTRL);
439 if (hcntrl == 0xFF)
440 goto fail;
441
442 /*
443 * Next create a situation where write combining
444 * or read prefetching could be initiated by the
445 * CPU or host bridge. Our device does not support
446 * either, so look for data corruption and/or flaged
447 * PCI errors. First pause without causing another
448 * chip reset.
449 */
450 hcntrl &= ~CHIPRST;
451 ahd_outb(ahd, HCNTRL, hcntrl|PAUSE);
452 while (ahd_is_paused(ahd) == 0)
453 ;
454
455 /* Clear any PCI errors that occurred before our driver attached. */
456 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
457 targpcistat = ahd_inb(ahd, TARGPCISTAT);
458 ahd_outb(ahd, TARGPCISTAT, targpcistat);
459 pci_status1 = ahd_pci_read_config(ahd->dev_softc,
460 PCIR_STATUS + 1, /*bytes*/1);
461 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1,
462 pci_status1, /*bytes*/1);
463 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
464 ahd_outb(ahd, CLRINT, CLRPCIINT);
465
466 ahd_outb(ahd, SEQCTL0, PERRORDIS);
467 ahd_outl(ahd, SRAM_BASE, 0x5aa555aa);
468 if (ahd_inl(ahd, SRAM_BASE) != 0x5aa555aa)
469 goto fail;
470
471 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) {
472 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
473 targpcistat = ahd_inb(ahd, TARGPCISTAT);
474 if ((targpcistat & STA) != 0)
475 goto fail;
476 }
477
478 error = 0;
479
480 fail:
481 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) {
482
483 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
484 targpcistat = ahd_inb(ahd, TARGPCISTAT);
485
486 /* Silently clear any latched errors. */
487 ahd_outb(ahd, TARGPCISTAT, targpcistat);
488 pci_status1 = ahd_pci_read_config(ahd->dev_softc,
489 PCIR_STATUS + 1, /*bytes*/1);
490 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1,
491 pci_status1, /*bytes*/1);
492 ahd_outb(ahd, CLRINT, CLRPCIINT);
493 }
494 ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS);
495 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2);
496 return (error);
497 }
498
499 /*
500 * Check the external port logic for a serial eeprom
501 * and termination/cable detection contrls.
502 */
503 static int
ahd_check_extport(struct ahd_softc * ahd)504 ahd_check_extport(struct ahd_softc *ahd)
505 {
506 struct vpd_config vpd;
507 struct seeprom_config *sc;
508 u_int adapter_control;
509 int have_seeprom;
510 int error;
511
512 sc = ahd->seep_config;
513 have_seeprom = ahd_acquire_seeprom(ahd);
514 if (have_seeprom) {
515 u_int start_addr;
516
517 /*
518 * Fetch VPD for this function and parse it.
519 */
520 if (bootverbose)
521 printk("%s: Reading VPD from SEEPROM...",
522 ahd_name(ahd));
523
524 /* Address is always in units of 16bit words */
525 start_addr = ((2 * sizeof(*sc))
526 + (sizeof(vpd) * (ahd->channel - 'A'))) / 2;
527
528 error = ahd_read_seeprom(ahd, (uint16_t *)&vpd,
529 start_addr, sizeof(vpd)/2,
530 /*bytestream*/TRUE);
531 if (error == 0)
532 error = ahd_parse_vpddata(ahd, &vpd);
533 if (bootverbose)
534 printk("%s: VPD parsing %s\n",
535 ahd_name(ahd),
536 error == 0 ? "successful" : "failed");
537
538 if (bootverbose)
539 printk("%s: Reading SEEPROM...", ahd_name(ahd));
540
541 /* Address is always in units of 16bit words */
542 start_addr = (sizeof(*sc) / 2) * (ahd->channel - 'A');
543
544 error = ahd_read_seeprom(ahd, (uint16_t *)sc,
545 start_addr, sizeof(*sc)/2,
546 /*bytestream*/FALSE);
547
548 if (error != 0) {
549 printk("Unable to read SEEPROM\n");
550 have_seeprom = 0;
551 } else {
552 have_seeprom = ahd_verify_cksum(sc);
553
554 if (bootverbose) {
555 if (have_seeprom == 0)
556 printk ("checksum error\n");
557 else
558 printk ("done.\n");
559 }
560 }
561 ahd_release_seeprom(ahd);
562 }
563
564 if (!have_seeprom) {
565 u_int nvram_scb;
566
567 /*
568 * Pull scratch ram settings and treat them as
569 * if they are the contents of an seeprom if
570 * the 'ADPT', 'BIOS', or 'ASPI' signature is found
571 * in SCB 0xFF. We manually compose the data as 16bit
572 * values to avoid endian issues.
573 */
574 ahd_set_scbptr(ahd, 0xFF);
575 nvram_scb = ahd_inb_scbram(ahd, SCB_BASE + NVRAM_SCB_OFFSET);
576 if (nvram_scb != 0xFF
577 && ((ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A'
578 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'D'
579 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P'
580 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'T')
581 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'B'
582 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'I'
583 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'O'
584 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'S')
585 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A'
586 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'S'
587 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P'
588 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'I'))) {
589 uint16_t *sc_data;
590 int i;
591
592 ahd_set_scbptr(ahd, nvram_scb);
593 sc_data = (uint16_t *)sc;
594 for (i = 0; i < 64; i += 2)
595 *sc_data++ = ahd_inw_scbram(ahd, SCB_BASE+i);
596 have_seeprom = ahd_verify_cksum(sc);
597 if (have_seeprom)
598 ahd->flags |= AHD_SCB_CONFIG_USED;
599 }
600 }
601
602 #ifdef AHD_DEBUG
603 if (have_seeprom != 0
604 && (ahd_debug & AHD_DUMP_SEEPROM) != 0) {
605 uint16_t *sc_data;
606 int i;
607
608 printk("%s: Seeprom Contents:", ahd_name(ahd));
609 sc_data = (uint16_t *)sc;
610 for (i = 0; i < (sizeof(*sc)); i += 2)
611 printk("\n\t0x%.4x", sc_data[i]);
612 printk("\n");
613 }
614 #endif
615
616 if (!have_seeprom) {
617 if (bootverbose)
618 printk("%s: No SEEPROM available.\n", ahd_name(ahd));
619 ahd->flags |= AHD_USEDEFAULTS;
620 error = ahd_default_config(ahd);
621 adapter_control = CFAUTOTERM|CFSEAUTOTERM;
622 kfree(ahd->seep_config);
623 ahd->seep_config = NULL;
624 } else {
625 error = ahd_parse_cfgdata(ahd, sc);
626 adapter_control = sc->adapter_control;
627 }
628 if (error != 0)
629 return (error);
630
631 ahd_configure_termination(ahd, adapter_control);
632
633 return (0);
634 }
635
636 static void
ahd_configure_termination(struct ahd_softc * ahd,u_int adapter_control)637 ahd_configure_termination(struct ahd_softc *ahd, u_int adapter_control)
638 {
639 int error;
640 u_int sxfrctl1;
641 uint8_t termctl;
642 uint32_t devconfig;
643
644 devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4);
645 devconfig &= ~STPWLEVEL;
646 if ((ahd->flags & AHD_STPWLEVEL_A) != 0)
647 devconfig |= STPWLEVEL;
648 if (bootverbose)
649 printk("%s: STPWLEVEL is %s\n",
650 ahd_name(ahd), (devconfig & STPWLEVEL) ? "on" : "off");
651 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, devconfig, /*bytes*/4);
652
653 /* Make sure current sensing is off. */
654 if ((ahd->flags & AHD_CURRENT_SENSING) != 0) {
655 (void)ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0);
656 }
657
658 /*
659 * Read to sense. Write to set.
660 */
661 error = ahd_read_flexport(ahd, FLXADDR_TERMCTL, &termctl);
662 if ((adapter_control & CFAUTOTERM) == 0) {
663 if (bootverbose)
664 printk("%s: Manual Primary Termination\n",
665 ahd_name(ahd));
666 termctl &= ~(FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH);
667 if ((adapter_control & CFSTERM) != 0)
668 termctl |= FLX_TERMCTL_ENPRILOW;
669 if ((adapter_control & CFWSTERM) != 0)
670 termctl |= FLX_TERMCTL_ENPRIHIGH;
671 } else if (error != 0) {
672 printk("%s: Primary Auto-Term Sensing failed! "
673 "Using Defaults.\n", ahd_name(ahd));
674 termctl = FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH;
675 }
676
677 if ((adapter_control & CFSEAUTOTERM) == 0) {
678 if (bootverbose)
679 printk("%s: Manual Secondary Termination\n",
680 ahd_name(ahd));
681 termctl &= ~(FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH);
682 if ((adapter_control & CFSELOWTERM) != 0)
683 termctl |= FLX_TERMCTL_ENSECLOW;
684 if ((adapter_control & CFSEHIGHTERM) != 0)
685 termctl |= FLX_TERMCTL_ENSECHIGH;
686 } else if (error != 0) {
687 printk("%s: Secondary Auto-Term Sensing failed! "
688 "Using Defaults.\n", ahd_name(ahd));
689 termctl |= FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH;
690 }
691
692 /*
693 * Now set the termination based on what we found.
694 */
695 sxfrctl1 = ahd_inb(ahd, SXFRCTL1) & ~STPWEN;
696 ahd->flags &= ~AHD_TERM_ENB_A;
697 if ((termctl & FLX_TERMCTL_ENPRILOW) != 0) {
698 ahd->flags |= AHD_TERM_ENB_A;
699 sxfrctl1 |= STPWEN;
700 }
701 /* Must set the latch once in order to be effective. */
702 ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN);
703 ahd_outb(ahd, SXFRCTL1, sxfrctl1);
704
705 error = ahd_write_flexport(ahd, FLXADDR_TERMCTL, termctl);
706 if (error != 0) {
707 printk("%s: Unable to set termination settings!\n",
708 ahd_name(ahd));
709 } else if (bootverbose) {
710 printk("%s: Primary High byte termination %sabled\n",
711 ahd_name(ahd),
712 (termctl & FLX_TERMCTL_ENPRIHIGH) ? "En" : "Dis");
713
714 printk("%s: Primary Low byte termination %sabled\n",
715 ahd_name(ahd),
716 (termctl & FLX_TERMCTL_ENPRILOW) ? "En" : "Dis");
717
718 printk("%s: Secondary High byte termination %sabled\n",
719 ahd_name(ahd),
720 (termctl & FLX_TERMCTL_ENSECHIGH) ? "En" : "Dis");
721
722 printk("%s: Secondary Low byte termination %sabled\n",
723 ahd_name(ahd),
724 (termctl & FLX_TERMCTL_ENSECLOW) ? "En" : "Dis");
725 }
726 return;
727 }
728
729 #define DPE 0x80
730 #define SSE 0x40
731 #define RMA 0x20
732 #define RTA 0x10
733 #define STA 0x08
734 #define DPR 0x01
735
736 static const char *split_status_source[] =
737 {
738 "DFF0",
739 "DFF1",
740 "OVLY",
741 "CMC",
742 };
743
744 static const char *pci_status_source[] =
745 {
746 "DFF0",
747 "DFF1",
748 "SG",
749 "CMC",
750 "OVLY",
751 "NONE",
752 "MSI",
753 "TARG"
754 };
755
756 static const char *split_status_strings[] =
757 {
758 "%s: Received split response in %s.\n",
759 "%s: Received split completion error message in %s\n",
760 "%s: Receive overrun in %s\n",
761 "%s: Count not complete in %s\n",
762 "%s: Split completion data bucket in %s\n",
763 "%s: Split completion address error in %s\n",
764 "%s: Split completion byte count error in %s\n",
765 "%s: Signaled Target-abort to early terminate a split in %s\n"
766 };
767
768 static const char *pci_status_strings[] =
769 {
770 "%s: Data Parity Error has been reported via PERR# in %s\n",
771 "%s: Target initial wait state error in %s\n",
772 "%s: Split completion read data parity error in %s\n",
773 "%s: Split completion address attribute parity error in %s\n",
774 "%s: Received a Target Abort in %s\n",
775 "%s: Received a Master Abort in %s\n",
776 "%s: Signal System Error Detected in %s\n",
777 "%s: Address or Write Phase Parity Error Detected in %s.\n"
778 };
779
780 static void
ahd_pci_intr(struct ahd_softc * ahd)781 ahd_pci_intr(struct ahd_softc *ahd)
782 {
783 uint8_t pci_status[8];
784 ahd_mode_state saved_modes;
785 u_int pci_status1;
786 u_int intstat;
787 u_int i;
788 u_int reg;
789
790 intstat = ahd_inb(ahd, INTSTAT);
791
792 if ((intstat & SPLTINT) != 0)
793 ahd_pci_split_intr(ahd, intstat);
794
795 if ((intstat & PCIINT) == 0)
796 return;
797
798 printk("%s: PCI error Interrupt\n", ahd_name(ahd));
799 saved_modes = ahd_save_modes(ahd);
800 ahd_dump_card_state(ahd);
801 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
802 for (i = 0, reg = DF0PCISTAT; i < 8; i++, reg++) {
803
804 if (i == 5)
805 continue;
806 pci_status[i] = ahd_inb(ahd, reg);
807 /* Clear latched errors. So our interrupt deasserts. */
808 ahd_outb(ahd, reg, pci_status[i]);
809 }
810
811 for (i = 0; i < 8; i++) {
812 u_int bit;
813
814 if (i == 5)
815 continue;
816
817 for (bit = 0; bit < 8; bit++) {
818
819 if ((pci_status[i] & (0x1 << bit)) != 0) {
820 const char *s;
821
822 s = pci_status_strings[bit];
823 if (i == 7/*TARG*/ && bit == 3)
824 s = "%s: Signaled Target Abort\n";
825 printk(s, ahd_name(ahd), pci_status_source[i]);
826 }
827 }
828 }
829 pci_status1 = ahd_pci_read_config(ahd->dev_softc,
830 PCIR_STATUS + 1, /*bytes*/1);
831 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1,
832 pci_status1, /*bytes*/1);
833 ahd_restore_modes(ahd, saved_modes);
834 ahd_outb(ahd, CLRINT, CLRPCIINT);
835 ahd_unpause(ahd);
836 }
837
838 static void
ahd_pci_split_intr(struct ahd_softc * ahd,u_int intstat)839 ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat)
840 {
841 uint8_t split_status[4];
842 uint8_t split_status1[4];
843 uint8_t sg_split_status[2];
844 uint8_t sg_split_status1[2];
845 ahd_mode_state saved_modes;
846 u_int i;
847 uint16_t pcix_status;
848
849 /*
850 * Check for splits in all modes. Modes 0 and 1
851 * additionally have SG engine splits to look at.
852 */
853 pcix_status = ahd_pci_read_config(ahd->dev_softc, PCIXR_STATUS,
854 /*bytes*/2);
855 printk("%s: PCI Split Interrupt - PCI-X status = 0x%x\n",
856 ahd_name(ahd), pcix_status);
857 saved_modes = ahd_save_modes(ahd);
858 for (i = 0; i < 4; i++) {
859 ahd_set_modes(ahd, i, i);
860
861 split_status[i] = ahd_inb(ahd, DCHSPLTSTAT0);
862 split_status1[i] = ahd_inb(ahd, DCHSPLTSTAT1);
863 /* Clear latched errors. So our interrupt deasserts. */
864 ahd_outb(ahd, DCHSPLTSTAT0, split_status[i]);
865 ahd_outb(ahd, DCHSPLTSTAT1, split_status1[i]);
866 if (i > 1)
867 continue;
868 sg_split_status[i] = ahd_inb(ahd, SGSPLTSTAT0);
869 sg_split_status1[i] = ahd_inb(ahd, SGSPLTSTAT1);
870 /* Clear latched errors. So our interrupt deasserts. */
871 ahd_outb(ahd, SGSPLTSTAT0, sg_split_status[i]);
872 ahd_outb(ahd, SGSPLTSTAT1, sg_split_status1[i]);
873 }
874
875 for (i = 0; i < 4; i++) {
876 u_int bit;
877
878 for (bit = 0; bit < 8; bit++) {
879
880 if ((split_status[i] & (0x1 << bit)) != 0)
881 printk(split_status_strings[bit], ahd_name(ahd),
882 split_status_source[i]);
883
884 if (i > 1)
885 continue;
886
887 if ((sg_split_status[i] & (0x1 << bit)) != 0)
888 printk(split_status_strings[bit], ahd_name(ahd), "SG");
889 }
890 }
891 /*
892 * Clear PCI-X status bits.
893 */
894 ahd_pci_write_config(ahd->dev_softc, PCIXR_STATUS,
895 pcix_status, /*bytes*/2);
896 ahd_outb(ahd, CLRINT, CLRSPLTINT);
897 ahd_restore_modes(ahd, saved_modes);
898 }
899
900 static int
ahd_aic7901_setup(struct ahd_softc * ahd)901 ahd_aic7901_setup(struct ahd_softc *ahd)
902 {
903
904 ahd->chip = AHD_AIC7901;
905 ahd->features = AHD_AIC7901_FE;
906 return (ahd_aic790X_setup(ahd));
907 }
908
909 static int
ahd_aic7901A_setup(struct ahd_softc * ahd)910 ahd_aic7901A_setup(struct ahd_softc *ahd)
911 {
912
913 ahd->chip = AHD_AIC7901A;
914 ahd->features = AHD_AIC7901A_FE;
915 return (ahd_aic790X_setup(ahd));
916 }
917
918 static int
ahd_aic7902_setup(struct ahd_softc * ahd)919 ahd_aic7902_setup(struct ahd_softc *ahd)
920 {
921 ahd->chip = AHD_AIC7902;
922 ahd->features = AHD_AIC7902_FE;
923 return (ahd_aic790X_setup(ahd));
924 }
925
926 static int
ahd_aic790X_setup(struct ahd_softc * ahd)927 ahd_aic790X_setup(struct ahd_softc *ahd)
928 {
929 ahd_dev_softc_t pci;
930 u_int rev;
931
932 pci = ahd->dev_softc;
933 rev = ahd_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
934 if (rev < ID_AIC7902_PCI_REV_A4) {
935 printk("%s: Unable to attach to unsupported chip revision %d\n",
936 ahd_name(ahd), rev);
937 ahd_pci_write_config(pci, PCIR_COMMAND, 0, /*bytes*/2);
938 return (ENXIO);
939 }
940 ahd->channel = ahd_get_pci_function(pci) + 'A';
941 if (rev < ID_AIC7902_PCI_REV_B0) {
942 /*
943 * Enable A series workarounds.
944 */
945 ahd->bugs |= AHD_SENT_SCB_UPDATE_BUG|AHD_ABORT_LQI_BUG
946 | AHD_PKT_BITBUCKET_BUG|AHD_LONG_SETIMO_BUG
947 | AHD_NLQICRC_DELAYED_BUG|AHD_SCSIRST_BUG
948 | AHD_LQO_ATNO_BUG|AHD_AUTOFLUSH_BUG
949 | AHD_CLRLQO_AUTOCLR_BUG|AHD_PCIX_MMAPIO_BUG
950 | AHD_PCIX_CHIPRST_BUG|AHD_PCIX_SCBRAM_RD_BUG
951 | AHD_PKTIZED_STATUS_BUG|AHD_PKT_LUN_BUG
952 | AHD_MDFF_WSCBPTR_BUG|AHD_REG_SLOW_SETTLE_BUG
953 | AHD_SET_MODE_BUG|AHD_BUSFREEREV_BUG
954 | AHD_NONPACKFIFO_BUG|AHD_PACED_NEGTABLE_BUG
955 | AHD_FAINT_LED_BUG;
956
957 /*
958 * IO Cell parameter setup.
959 */
960 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29);
961
962 if ((ahd->flags & AHD_HP_BOARD) == 0)
963 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVA);
964 } else {
965 /* This is revision B and newer. */
966 extern uint32_t aic79xx_slowcrc;
967 u_int devconfig1;
968
969 ahd->features |= AHD_RTI|AHD_NEW_IOCELL_OPTS
970 | AHD_NEW_DFCNTRL_OPTS|AHD_FAST_CDB_DELIVERY
971 | AHD_BUSFREEREV_BUG;
972 ahd->bugs |= AHD_LQOOVERRUN_BUG|AHD_EARLY_REQ_BUG;
973
974 /* If the user requested that the SLOWCRC bit to be set. */
975 if (aic79xx_slowcrc)
976 ahd->features |= AHD_AIC79XXB_SLOWCRC;
977
978 /*
979 * Some issues have been resolved in the 7901B.
980 */
981 if ((ahd->features & AHD_MULTI_FUNC) != 0)
982 ahd->bugs |= AHD_INTCOLLISION_BUG|AHD_ABORT_LQI_BUG;
983
984 /*
985 * IO Cell parameter setup.
986 */
987 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29);
988 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVB);
989 AHD_SET_AMPLITUDE(ahd, AHD_AMPLITUDE_DEF);
990
991 /*
992 * Set the PREQDIS bit for H2B which disables some workaround
993 * that doesn't work on regular PCI busses.
994 * XXX - Find out exactly what this does from the hardware
995 * folks!
996 */
997 devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1);
998 ahd_pci_write_config(pci, DEVCONFIG1,
999 devconfig1|PREQDIS, /*bytes*/1);
1000 devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1);
1001 }
1002
1003 return (0);
1004 }
1005