Searched full:tolerance (Results 1 – 25 of 29) sorted by relevance
12
| /Documentation/power/ |
| D | pm_qos_interface.rst | 92 state latency tolerance (in microseconds) and the third one is for PM QoS flags.
95 The target values of resume latency and active state latency tolerance are
181 Active state latency tolerance
190 If there is a latency tolerance control mechanism for a given device available
196 Whenever the effective latency tolerance changes for the device, its
199 latency tolerance requirements for the device is empty, the callback is expected
200 to switch the underlying hardware latency tolerance control mechanism to an
204 automatically updating the device's latency tolerance in response to its power
206 be done in the autonomous latency tolerance control mode.
210 Then, user space can use that attribute to specify its latency tolerance
[all …]
|
| /Documentation/misc-devices/ |
| D | ad525x_dpot.rst | 9 settings. Access to the factory programmed tolerance is also provided, but
16 Each dpot device will have a set of eeprom, rdac, and tolerance files. How
23 The tolerance files are the read-only factory programmed tolerance settings
|
| /Documentation/hwmon/ |
| D | w83792d.rst | 145 via thermal_cruise# file. The tolerance# file serves to create T +- tolerance
147 remains below the thermal_cruise# +- tolerance# value. Once the temperature
148 exceeds the high limit (T+tolerance), the fan will be turned on with a
156 limit (T-tolerance), the fan speed will be fixed at the current speed because
168 temperature region (sf2_point@_fan# +- tolerance#) it will cause fans to run
194 tolerance[1-3]
|
| D | nct6775.rst | 192 Temperature step tolerance.
204 Target temperature tolerance, unit millidegree Celsius
240 Target speed tolerance
264 Temperature tolerance, unit millidegree Celsius
267 Temperature tolerance for critical temperature,
|
| D | w83793.rst | 89 predefined value, within a tolerance margin. So if tempX_input >
92 the PWM value. If the temperature is within the tolerance range, the PWM
|
| D | w83l786ng.rst | 65 tolerance[1-2]
|
| D | nsa320.rst | 58 reasonable tolerance.
|
| D | dell-smm-hwmon.rst | 303 ``0x05a3`` Get fan speed tolerance Returns the speed tolerance for each fan state:
309 tolerance
|
| D | ds1621.rst | 80 A second thing is that, during extensive testing, Tout showed a tolerance
|
| D | w83791d.rst | 142 temp[1-3]_tolerance temperature tolerance for Thermal Cruise mode.
|
| D | w83627ehf.rst | 178 tolerance, unit millidegree Celsius (range 0 - 15000)
|
| /Documentation/ABI/removed/ |
| D | sysfs-mce | 14 Tolerance level. When a machine check exception occurs for a
20 defies normal kernel locking rules. The tolerance level
|
| /Documentation/devicetree/bindings/cpufreq/ |
| D | cpufreq-dt.txt | 19 - voltage-tolerance: Specify the CPU voltage tolerance in percentage.
|
| /Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra20-hsuart.yaml | 70 Standard UART devices are expected to have tolerance for baud rate error by -4 to +4 %. All
72 issue. UART RX baud rate tolerance level is 0% to +4% in 1-stop config. Otherwise, the
|
| /Documentation/filesystems/ |
| D | btrfs.rst | 8 features while focusing on fault tolerance, repair and easy administration.
|
| /Documentation/userspace-api/media/rc/ |
| D | lirc-get-rec-resolution.rst | 40 tolerance value.
|
| /Documentation/devicetree/bindings/gpio/ |
| D | aspeed,sgpio.yaml | 19 - Support reset tolerance option for each output port
|
| /Documentation/ABI/testing/ |
| D | sysfs-devices-power | 229 contains the PM QoS active state latency tolerance limit for the
234 but hardware should not be allowed to set the latency tolerance
241 latency tolerance requirements from the kernel side.
|
| D | sysfs-platform-dfl-port | 46 Description: Read-write. Read or set AFU latency tolerance reporting value.
|
| D | sysfs-platform-dfl-fme | 243 Description: Read-only. Read this file to get current Latency Tolerance
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | ti,ads7843.yaml | 55 Tolerance used for filtering.
|
| /Documentation/dev-tools/ |
| D | autofdo.rst | 45 some tolerance for source changes. This mode is commonly used in a
|
| /Documentation/devicetree/bindings/regulator/ |
| D | regulator.yaml | 66 reach the target voltage, plus/minus whatever tolerance the board
|
| /Documentation/driver-api/cxl/ |
| D | memory-devices.rst | 25 multiple Host Bridges and endpoints while another may opt for fault tolerance
|
| /Documentation/devicetree/bindings/remoteproc/ |
| D | ti,k3-r5f-rproc.yaml | 15 either in a LockStep mode providing safety/fault tolerance features or in a
|
12